Pasar al contenido principal

ELECTROQUIMICA DE SUPERFICIES Y COMBUSTIBLES SOSTENIBLES

CTQ2010-16271

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSIDAD DE ALICANTE
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 33
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the electrochemical properties of platinum stepped surfaces vicinal to the (100) pole. A computational study

  • Ferre Vilaplana, Adolfo
  • Gisbert, Ruben
  • Herrero, Enrique
DFT studies on platinum stepped surfaces have been carried out in order to understand the differences in the electrochemical behavior between the surfaces with (111) and (100) terraces. Thus, adsorption energies of different species on selected surfaces have been computed. For the adsorption of Bi and Cu on the Pt(553) and Pt(711) surfaces, it has been found that the adsorption energy on the site corresponding to the step decoration for the Pt(553) surface is ca. 0.5 eV higher than that calculated on the (111) terrace sites. On the other hand, there is no preferential adsorption site for Cu or Bi on the Pt(711) surface, since the energy differences between the different sites on this stepped surface with (100) terraces are very small. CO and OH adsorption on the surfaces with (100) terraces, namely the Pt(100), the Pt(711) and the Pt(510) surfaces, has been also investigated. The energy differences between step sites and terrace sites for the surfaces are very small, ca. 0.2 eV for OH adsorption and <0.1 eV for CO adsorption. For OH, the preferred adsorption mode is a bridge mode, whereas the adsorption energy for the on top and bridge configurations of CO are similar on those surfaces. The comparison with previous DFT calculations indicates that the perturbation created by the step on the (100) terrace is significantly smaller than that created on the (111) terraces. Thus, the modification of the electrochemical properties produced by the presence of a step in the (100) terrace is minor, in agreement with the experimental results. (C) 2014 Elsevier Ltd. All rights reserved., This work has been financially supported by the MICINN (Spain) (project CTQ2010-16271-FEDER) and Generalitat Valenciana (project PROMETEO/2009/045, -FEDER).
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Influence of the CO Adsorption Environment on Its Reactivity with (111) Terrace Sites in Stepped Pt Electrodes under Alkaline Media

  • Farias, Manuel J.S.
  • Busó-Rogero, Carlos
  • Gisbert, Rubén
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
The effect of the electrode potential in the reactivity of platinum stepped single crystal electrodes with (111) terraces toward CO oxidation has been studied. It is found that the CO adlayer is significantly affected by the potential at which the adlayer is formed. The electrochemical and FTIR experiments show that the adsorbed CO layer formed in acidic solution at 0.03 V vs SHE is different from that formed at −0.67 V vs SHE in alkaline solutions. The major effect of the electrode potential is a change in the long-range structure of CO adlayer. The adlayer formed in alkaline media presents a higher number of defects. These differences affect the onset and peak potential for CO stripping experiments. The stripping voltammogram for the adlayer formed at −0.67 V vs SHE always shows a prewave and the peak potential is more negative than that observed for the adlayer formed at 0.03 V vs SHE. This means that the apparent higher activity for CO oxidation observed in alkaline media is a consequence of the different CO adlayer structure on the (111) terrace, and not a true catalytic effect. The different behavior is discussed in terms of the different mobility of CO observed depending on the electrode potential. Also, the FTIR frequencies are used to estimate the pzc (potential of zero charge) for the Pt(111) electrode covered with a CO adlayer.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Electrochemical features of Pt(S)[n(110) × (100)] surfaces in acidic media

  • Souza-Garcia, Janaina
  • Angelucci, Camilo Andrea
  • Climent, Victor
  • Feliu, Juan M.
  • Climent, Victor|||/items/f8d596b7-a0df-492d-8e11-794f68d84268
Experiments have been carried out in sulfuric and perchloric acid solutions on Pt(S)[n(110) × (100)] electrodes. The comparison between the two different electrolytic media reveals an important influence of the anion in the voltammetric features. Total charge curves have been obtained with the CO charge displacement method in combination with voltammetric measurements. From these curves, the dependence of the pztc with the step density and the strength of the anion adsorption have been analyzed. The problem of the so-called third peak is treated for a series of electrodes that contain (110) terraces, revealing the requirement of (110) domains for occurrence of this adsorption state.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Sequential Pt(1 1 1) oxide formation in perchloric acid: An electrochemical study of surface species inter-conversion

  • Gómez Marín, Ana María
  • Clavilier, Jean
  • Feliu, Juan M.
A significant number of electrocatalytic reactions take place in a potential region in which the surface of platinum is partly covered by oxygenated species. Hence, the mechanism of the electrochemical formation and reduction of surface oxides is fundamental to understand how its properties can determine the reactivity of the catalyst. In this paper, the dynamic of the initial states of the electrochemical oxide growth on Pt(1 1 1), in the absence of anion specific adsorption and keeping surface stability, is studied by employing electrochemical techniques. Several species, such as chemisorbed hydroxide and oxygen, initial Pt oxide structures and even sub-surface oxygen, interconvert and interact. Their existences depend more strongly on the total surface coverage than on the electrode potential. Considering structural and thermodynamic data related to the identity of the electrochemical oxide film at platinum, the results suggest that Pt(1 1 1) oxide starts by water dissociation to OHads followed by its electrochemical oxidation to Oads at higher potentials. The latter process occurs as a phase transition through a nucleation and growth mechanism, until a stable adlayer is formed. In parallel, Oads transforms to an initial Pt oxide structure. Thus, there are at least two types of processes involved in the growth of the surface oxide layer (i.e. two states of oxide films), and the separation between anodic and cathodic j–E profiles reflects a true hysteresis arising from a change of state of the surface oxide film.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Some reflections on the understanding of the oxygen reduction reaction at Pt(111)

  • Gómez Marín, Ana María
  • Rizo, Rubén
  • Feliu, Juan M.
  • Rizo, Rubén|||/items/27448570-0e85-47c3-be0f-38bcb1bf11b3
The oxygen reduction reaction (ORR) is a pivotal process in electrochemistry. Unfortunately, after decades of intensive research, a fundamental knowledge about its reaction mechanism is still lacking. In this paper, a global and critical view on the most important experimental and theoretical results regarding the ORR on Pt(111) and its vicinal surfaces, in both acidic and alkaline media, is taken. Phenomena such as the ORR surface structure sensitivity and the lack of a reduction current at high potentials are discussed in the light of the surface oxidation and disordering processes and the possible relevance of the hydrogen peroxide reduction and oxidation reactions in the ORR mechanism. The necessity to build precise and realistic reaction models, which are deducted from reliable experimental results that need to be carefully taken under strict working conditions is shown. Therefore, progress in the understanding of this important reaction on a molecular level, and the choice of the right approach for the design of the electrocatalysts for fuel-cell cathodes is only possible through a cooperative approach between theory and experiments.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Effects of the anion adsorption and pH on the formic acid oxidation reaction on Pt(111) electrodes

  • Perales-Rondón, Juan V.
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
The effects of solution pH and anion adsorption for the formic acid oxidation reaction on the Pt(111) electrode have been examined using electrochemical techniques. Regarding the pH effects, it has been found that oxidation currents for this reaction increase with pH, which indicates that solution formate is involved in the reaction mechanism. Unexpectedly, the adsorption of sulfate on the Pt(111) electrode has a positive effect on the oxidation of formic acid, which also suggests that adsorbed anions are also involved in the mechanism. The activation energy calculated from temperature dependent measurements diminishes with the solution pH and also in the presence of adsorbed sulfate. These measurements corroborate the involvement of solution formate and anions in the oxidation mechanism. Using these results, a rate equation for the oxidation of formic acid is proposed. The current values calculated from this equation are in very good agreement with the experimental currents in perchloric acid solutions.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

On the electrochemical properties of platinum stepped surfaces vicinal to the (100) pole. A computational study

  • Ferre-Vilaplana, Adolfo
  • Gisbert, Rubén
  • Herrero, Enrique
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
DFT studies on platinum stepped surfaces have been carried out in order to understand the differences in the electrochemical behavior between the surfaces with (111) and (100) terraces. Thus, adsorption energies of different species on selected surfaces have been computed. For the adsorption of Bi and Cu on the Pt(553) and Pt(711) surfaces, it has been found that that the adsorption energy on the site corresponding to the step decoration for the Pt(553) surface is ca. 0.5 eV higher than that calculated on the (111) terrace sites. On the other hand, there is no preferential adsorption site for Cu or Bi on the Pt(711) surface, since the energy differences between the different sites on this stepped surface with (100) terraces are very small. CO and OH adsorption on the surface with (100) terraces, namely the Pt(100), the Pt(711) and the Pt(510) surfaces, have been also investigated. The energy differences between step sites and terrace sites for both surfaces is very small, ca. 0.2 eV for OH adsorption and <0.1 eV for CO adsorption. For OH, the preferred adsorption mode is a bridge mode, whereas the adsorption energy for the on top and bridge configurations of CO are similar on those surfaces. The comparison with previous DFT calculations indicates that the perturbation created by the step on the (100) terrace is significantly smaller than that created on the (111) terraces. Thus, the modification of the electrochemical properties produced by the presence of a step in the (100) terrace is minor, in agreement with the experimental results.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Oxidation of Ethanol and Its Derivatives on Well Defined Pt Single Crystal Electrodes Vicinal to Pt(111): A Comparative Study

  • Arán-Ais, Rosa M.
  • Santos, Nathalia Abe
  • Villullas, Hebe M.
  • Feliu, Juan M.
  • Arán-Ais, Rosa M.|||/items/9120125e-5943-4754-ba84-7200ee3b8c85
The oxidation of ethanol (EtOH) at Pt(111) electrodes is dominated by the 4e path leading to acetic acid. The inclusion of surface defects such as those present on stepped surfaces leads to an increase of the reactivity towards the most desirable 12e path leading to CO2 as final product. This path is also favored when the methyl group is more oxidized, as in the case of ethylene glycol (EG) that spontaneously decomposes to CO on Pt(111) electrodes, thus showing a more effective breaking of the C-C bond. Some trends in reactivity can be envisaged when other derivative molecules are compared at well-ordered electrodes. This strategy was used in the past, but the improvement in the electrode pretreatment and the overall information available on the subject suggest that relevant information is still missing.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Electrocatalysis of H2O2 reduction/oxidation at model platinum surfaces

  • Sitta, Elton
  • Gómez Marín, Ana María
  • Aldaz Riera, Antonio
  • Feliu, Juan M.
Oxidation (HPOR) and reduction (HPRR) reactions of hydrogen peroxide were studied on platinum single crystalline surfaces. Experimental curves were fitted to a simple model in which the whole process is described by the sum of two independent, mass controlled reactions. It is shown that stepped surfaces are more catalytic than basal planes for both HPOR and HPRR reactions. On the contrary, on oxide covered surfaces, those having large {111} terraces are better electrocatalysts for HPRR, but worse for HPOR. These results shed light concerning H2O2 reactivity on platinum surfaces and may help to unveil oxygen reduction reaction mechanism.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Oxygen reduction on nanostructured platinum surfaces in acidic media: Promoting effect of surface steps and ideal response of Pt(1 1 1)

  • Gómez Marín, Ana María
  • Feliu, Juan M.
In this paper, the role of surface steps on the electrocatalytic activity of platinum nanostructured surfaces for the oxygen reduction reaction (ORR) in acidic medium is evaluated by using stepped surfaces of structure Pt(S)[n(1 1 1) × (1 1 1)] with large terraces (20 ≤ n ≤ 50). It is realized that the inclusion of an even low amount of surface steps enhances the ORR, and linear activity trends are measured when currents at constant potential are plotted vs. the step density. As a consequence, an ideal ORR curve for a defect-free Pt(1 1 1) surface is extrapolated at zero defect density from experimental data and can be compared to that of a quasi-perfect Pt(1 1 1) electrode. It is clearly shown that surface steps promote the electrode activity toward ORR in acid medium. Results are discussed in light of available theoretical and experimental data.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

New Insights into the Oxygen Reduction Reaction Mechanism on Pt (111): A Detailed Electrochemical Study

  • Gómez Marín, Ana María
  • Feliu, Juan M.
The oxygen reduction reaction (ORR) is undoubtedly the most important fuel-cell cathodic reaction. In this work, a detailed electrochemical analysis of the ORR on Pt (111) in nonadsorbing electrolytes was performed, which included the high-potential region Eup=1.15 V while ensuring the electrode surface structure stability. Our results suggest that the reduction of a soluble intermediate species formed during the ORR is the rate-determining step in the whole reaction mechanism. This species does not undergo any other electrochemical reaction at E>0.9 V and may accumulate close to the electrode surface. Together with dissolved O2, this intermediate may modify the oxide-growth dynamics on Pt (111). Hence, both species interact with the electrode surface through complex catalytic networks. Under certain experimental conditions, oxygenated species from the oxidation of Pt (111) may enhance the overall ORR current. These results propose an alternative to explain the current state of the art for this fundamental process.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Tailoring properties of platinum supported catalysts by irreversible adsorbed adatoms toward ethanol oxidation for direct ethanol fuel cells

  • Figueiredo, Marta C.
  • Santasalo-Aarnio, Annukka
  • Vidal-Iglesias, Francisco J.
  • Solla-Gullón, José
  • Feliu, Juan M.
  • Kontturi, Kyösti
  • Kallio, Tanja
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
In this work ethanol oxidation on carbon supported Pt catalysts modified with irreversibly adsorbed adatoms is reported. This study concerns understanding of the effect of a second metal on real catalysts in conditions as close as possible to those applied in fuel cells systems. The results were acquired using cyclic voltammetry, chronoamperometry and in situ infra-red techniques always taking into account the future application of the electrocatalyst materials in fuel cells. Foreign adatoms, both Bi and Sb, irreversibly adsorbed on a Pt electrode were studied, and revealed to enhance catalytic activity toward a more efficient ethanol oxidation. The catalytic enhancement continuously increased with the coverage of the adatom on the surface up to coverages close to saturation. With these high coverages a decrease of the activity was observed suggesting that free platinum atoms are required to oxidize ethanol. The results suggest that the adatoms play a third body role avoiding the poisoning of the Pt sites that will then be free for oxidizing ethanol. However, electronic effects on Pt/C–Bi and bifunctional mechanism at Pt/C–Sb are also suggested. The oxidation products were identified by in situ FTIR and are mainly acetaldehyde and acetic acid for the three catalysts. CO2 was also observed for the unmodified Pt/C and interestingly for the Pt/C–Sb electrodes.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles

  • Busó-Rogero, Carlos
  • Grozovski, Vitali
  • Vidal-Iglesias, Francisco J.
  • Solla-Gullón, José
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
Ethanol oxidation on platinum nanoparticles with well-characterized surfaces is studied using cyclic voltammetry and FTIR techniques. Their behavior is compared with that obtained for platinum single crystal electrodes, in order to rationalize their performance and to understand the effects of the surface structure and anion adsorption on the reactivity. The results clearly demonstrate that there are strong effects of anion adsorption and surface structure on the measured current and oxidation mechanism. Thus, the main product of ethanol oxidation on (111) preferentially oriented Pt nanoparticles is acetic acid, and the amount of CO2 produced can be considered negligible. On the other hand, (100) preferentially oriented Pt nanoparticles are effective for the cleavage of the C–C bond yielding adsorbed CO, which eventually is oxidized to CO2. This nanoparticles electrode has the highest catalytic activity at high potentials, whereas (111) preferentially oriented Pt nanoparticles are more active at low potentials. In addition, no significant differences in the activity are reported by using different supporting electrolytes, which indicates that adsorbed acetate, which results from the adsorption of acetic acid, hinders ethanol oxidation.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Pt catalysts modified with Bi: Enhancement of the catalytic activity for alcohol oxidation in alkaline media

  • Figueiredo, Marta C.
  • Arán-Ais, Rosa M.
  • Feliu, Juan M.
  • Kontturi, Kyösti
  • Kallio, Tanja
  • Arán-Ais, Rosa M.|||/items/9120125e-5943-4754-ba84-7200ee3b8c85
Recent developments on anion-exchange membranes for fuel cell application renewed the interest in the study of alcohol oxidation at high pHs for applications in anion-exchange membrane direct alcohol fuel cells (AEM-DAFC). Although platinum is still the most studied catalyst for oxidation of alcohols in alkaline media, the introduction of one or more metals in order to increase the oxophilicity of the catalyst is a common approach in the development of improved materials for these reactions. In this manuscript, we report the enhancement of the catalytic activity of Pt/C toward ethanol, methanol, and propanol oxidation in alkaline media by simple adsorption of Bi surface. The activity was checked by cyclic voltammetry, and the reaction products and intermediates were analyzed by “in situ” infrared spectroscopy. The presence of Bi was shown to increase the activity of Pt toward the oxidation of the referred alcohols by acting as a third body (impeding surface poisoning) and also by an electronic effect (on water adsorption at the surface).
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Oxygen reduction reaction on stepped platinum surfaces in alkaline media

  • Rizo, Rubén
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
  • Rizo, Rubén|||/items/27448570-0e85-47c3-be0f-38bcb1bf11b3
The oxygen reduction reaction (ORR) in 0.1 M NaOH on platinum single crystal electrodes has been studied using hanging meniscus rotating disk electrode configuration. Basal planes and stepped surfaces with (111) and (100) terraces have been employed. The results indicate that the Pt(111) electrode has the highest electrocatalytic activity among all the studied surfaces. The addition of steps on this electrode surface significantly diminishes the reactivity of the surface towards the ORR. In fact, the reactivity of the steps on the surfaces with wide terraces can be considered negligible with respect to that measured for the terrace. On the other hand, Pt(100) and Pt(110) electrodes have much lower activity than the Pt(111) electrode. These results have been compared with those obtained in acid media to understand the effect of the pH and the adsorbed OH on the mechanism. It is proposed that the surface covered by adsorbed OH is active for the reduction of the oxygen molecules.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

On the behavior of the Pt(1 0 0) and vicinal surfaces in alkaline media

  • Arán-Ais, Rosa M.
  • Figueiredo, Marta C.
  • Vidal-Iglesias, Francisco J.
  • Climent, Victor
  • Herrero, Enrique
  • Feliu, Juan M.
  • Arán-Ais, Rosa M.|||/items/9120125e-5943-4754-ba84-7200ee3b8c85
  • Climent, Victor|||/items/f8d596b7-a0df-492d-8e11-794f68d84268
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
We address in this paper a voltammetric study of the charge transfer processes characteristic of Pt(1 0 0) and vicinal surfaces in alkaline media. The electrochemical behavior of a series of stepped surfaces of the type Pt(S)[n(1 0 0) × (1 1 1)] has been characterized using cyclic voltammetry at different pHs, charge displacement measurements and FTIR experiments for adsorbed CO. The results from these techniques allow assigning the different peaks appearing in the voltammogram to hydrogen and/or OH adsorption on the different sites of these surfaces, namely, terrace and step sites. Additionally, the potential of zero total charge (pztc) of the electrodes was determined. The resulting pztc values shift to more negative values when the step density increases on the surface up to n = 5. FTIR spectroscopy experiments have been used to monitor the adsorption of CO on the different surfaces as well as the consequent CO oxidation, accompanying a positive potential sweep. The oxidation of adsorbed CO on (1 0 0) terraces is catalyzed by the presence of the (1 1 1) steps. The FTIR spectra revealed that CO is mostly bonded in bridge configuration at low potentials interconverting to on-top when the electrode potential is increased.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Electrochemical Characterization of Shape-Controlled Pt Nanoparticles in Different Supporting Electrolytes

  • Vidal-Iglesias, Francisco J.
  • Arán-Ais, Rosa M.
  • Solla-Gullón, José
  • Herrero, Enrique
  • Feliu, Juan M.
  • Arán-Ais, Rosa M.|||/items/9120125e-5943-4754-ba84-7200ee3b8c85
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
The voltammetric profile of preferentially shaped platinum nanoparticles has been used to analyze the different sites present on the surface. For the first time, this analysis has been made in NaOH solutions and revisited in sulfuric and perchloric acid media. The comparison with the voltammetric profiles of the model surfaces, that is, single-crystal electrodes, allows assigning the different signals appearing in the voltammograms of the nanoparticle to specific sites on the surface. A good correlation between the shape of the nanoparticle determined by TEM and the voltammetric profile is obtained. For the nanoparticles characterized in alkaline media, the adsorbed species on the surface have been characterized, and three major regions can be identified. Below 0.2 V, the major contribution is due to hydrogen adsorption, whereas above 0.6 V, adsorbed OH is the main species on the surface. Between those values, the signals are due to the competitive adsorption/desorption process of OH/H. New criteria for determining the active area in NaOH solutions has been proposed. In this medium, the total charge density measured between 0.06 and 0.90 V stands for 390 μC cm–2. The areas measured are in perfect agreement with those measured in acid media. Once the nanoparticles have been characterized, the behavior of the nanoparticles toward CO oxidation is analyzed and compared with that observed for single-crystal electrodes.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Oxide growth dynamics at Pt(1 1 1) in absence of specific adsorption: A mechanistic study

  • Gómez Marín, Ana María
  • Feliu, Juan M.
A significant number of electrocatalytic reactions take place in a potential region in which the surface of platinum is partly covered by oxygenated species. Hence, the mechanism of the electrochemical formation and reduction of surface oxides is fundamental to understand how surface composition can determine the reactivity of the catalyst. In this paper, combined potential step chronoamperometry and cyclic voltammetry were performed to involve oxide formation and its evolution on Pt(1 1 1), in the absence of anion specific adsorption and keeping surface stability (0.95 < E < 1.1 V). As a first approximation, a simple mean field model scheme is outlined to describe the dynamics of the initial states of the electrochemical oxide growth on Pt(1 1 1). Qualitatively, the whole oxidation process can be properly described by the sequential electrochemical oxidation of water, in such a way that the main features of the cyclic voltammogram and potential step profiles can be explained. The results corroborate the existence of at least two different oxidation states of the surface. The first state is formed through a nucleation and growth mechanism controlled by the rate at which the nuclei are formed, i.e. it follows a progressive nucleation mechanism. The second state is a further ageing process that depends on the potential at which the oxide layer is fully developed. The final oxide film slows down subsequent water dissociation.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity

  • Busó-Rogero, Carlos
  • Perales-Rondón, Juan V.
  • Farias, Manuel J.S.
  • Vidal-Iglesias, Francisco J.
  • Solla-Gullón, José
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
Thallium modified shape-controlled Pt nanoparticles were prepared and their electrocatalytic activity towards formic acid electrooxidation was evaluated in 0.5 M sulfuric acid. The electrochemical and in situ FTIR spectroscopic results show a remarkable improvement in the electrocatalytic activity, especially in the low potential region (around 0.1–0.2 V vs. RHE). Cubic Pt nanoparticles modified with Tl were found to be more active than the octahedral Pt ones in the entire range of Tl coverages and potential windows. In situ FTIR spectra indicate that the promotional effect produced by Tl results in the inhibition of the poisoning step leading to COads, thus improving the onset potential for the complete formic acid oxidation to CO2. Chronoamperometric experiments were also performed at 0.2 V to evaluate the stability of the electrocatalysts at constant potential. Finally, experiments with different concentrations of formic acid (0.05–1 M) were also carried out. In all cases, Tl-modified cubic Pt nanoparticles result to be the most active. All these facts reinforce the importance of controlling the surface structure of the electrocatalysts to optimize their electrocatalytic properties.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

The breaking of the C-C bond in ethylene glycol oxidation at the Pt(111) electrode and its vicinal surfaces

  • Arán-Ais, Rosa M.
  • Herrero, Enrique
  • Feliu, Juan M.
  • Arán-Ais, Rosa M.|||/items/9120125e-5943-4754-ba84-7200ee3b8c85
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
Ethylene glycol (EG) oxidation has been studied on Pt(111) and its vicinal surfaces in acidic media by cyclic voltammetry and infrared spectroscopy. Even at Pt(111) the C-C bond is readily broken and CO is formed at low potentials. Both types of steps catalyze the EG oxidation to CO2, being the {110} steps the most catalytic for the splitting of the C-C bond. Spectroscopic results show that glycolic acid and oxalic acid are produced mainly at the close-packed terraces.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Towards More Active and Stable Electrocatalysts for Formic Acid Electrooxidation: Antimony-Decorated Octahedral Platinum Nanoparticles

  • Vidal-Iglesias, Francisco J.
  • López Cudero, Ana
  • Solla-Gullón, José
  • Feliu, Juan M.
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Size-Dependent and Step-Modulated Supramolecular Electrochemical Properties of Catechol-Derived Adlayers at Pt(hkl) Surfaces

  • Rodríguez López, Margarita
  • Herrero, Enrique
  • Climent, Victor
  • Rodes, Antonio
  • Aldaz Riera, Antonio
  • Feliu, Juan M.
  • Carrasquillo, Arnaldo Jr.
  • Climent, Victor|||/items/f8d596b7-a0df-492d-8e11-794f68d84268
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
  • Rodes, Antonio|||/items/0498f81b-f1a5-4f48-bee3-357d1a2c65e6
The electrochemical reactivity of catechol-derived adlayers is reported at platinum (Pt) single-crystal electrodes. Pt(111) and stepped vicinal surfaces are used as model surfaces possessing well-ordered nanometer-sized Pt(111) terraces ranging from 0.4 to 12 nm. The electrochemical experiments were designed to probe how the control of monatomic step-density and of atomic-level step structure can be used to modulate molecule–molecule interactions during self-assembly of aromatic-derived organic monolayers at metallic single-crystal electrode surfaces. A hard sphere model of surfaces and a simplified band formation model are used as a theoretical framework for interpretation of experimental results. The experimental results reveal (i) that supramolecular electrochemical effects may be confined, propagated, or modulated by the choice of atomic level crystallographic features (i.e.monatomic steps), deliberately introduced at metallic substrate surfaces, suggesting (ii) that substrate-defect engineering may be used to tune the macroscopic electronic properties of aromatic molecular adlayers and of smaller molecular aggregates.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Synthesis of Pt Nanoparticles in Water-in-Oil Microemulsion: Effect of HCl on Their Surface Structure

  • Martínez-Rodríguez, Roberto A.
  • Vidal-Iglesias, Francisco J.
  • Solla-Gullón, José
  • Cabrera, Carlos R.
  • Feliu, Juan M.
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
The synthesis of shape-controlled nanoparticles is currently a hot research topic. However, from an applied point of view, there is still a lack of easy, cheap, and scalable methodologies. In this communication we report, for the first time, the synthesis of cubic platinum nanoparticles with a very high yield using a water-in-oil microemulsion method, which unlike others, such as the colloidal method, fulfills the previous requirements. This shape/surface structure control is determined by the concentration of HCl in the water phase of the microemulsion. The results reported here show that the optimal HCl percentage in the water phase is about 25% to obtain the highest amount of cubic nanostructures. Ammonia electro-oxidation is used as a surface structure sensitive reaction to illustrate HCl surface structure effects. Moreover, in situ electrochemical characterization has been performed to study the nanoparticle surface structure.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Site Selectivity for CO Adsorption and Stripping on Stepped and Kinked Platinum Surfaces in Alkaline Medium

  • Farias, Manuel J.S.
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
This work reports experimental evidence that the adsorption of CO on Pt surfaces composed by (111) terraces and steps and/or kinks in alkaline media occurs faster on sites with (100) symmetry, followed by (110) sites. On the other hand, the (111) terrace has the lowest adsorption rate. CO electrooxidation demonstrates the existence of a close relationship between the preferential site CO occupancy and the peak multiplicity observed in CO stripping voltammetry. For the stepped Pt(554) and Pt(544) and kinked Pt(875) single crystal surfaces, the CO stripping process takes place at high potentials (0.80 V vs RHE) when only the (110) or (100) step sites are blocked by CO. However, when the terrace sites with (111) symmetry are fully occupied, new CO stripping peaks appear at lower potentials (<0.68 V vs RHE). For all surfaces, it is observed that the first released sites after partial CO oxidation are (111) terrace sites, followed by the step (110) sites and sites with (100) symmetry. The results of partial CO oxidation suggest that the diffusion of adsorbed CO from sites with (110) or (100) symmetry toward unoccupied (111) terrace sites is negligible. However, CO diffusion from terrace sites to step or kink sites cannot be discarded during the growth of the adsorbed CO adlayer, because of the preferential site occupancy for these latter sites. Due to the fact that the CO oxidation process on stepped Pt surfaces in alkaline media occurs at different potentials on different sites, the activation energies for CO oxidation on the different sites have been estimated. The results for full CO coverage and CO decorated stepped surfaces are in good agreement, indicating that the oxidation of CO on the different sites is not coupled. In the absence of CO on terrace sites, in situ FTIR spectroscopy shows that CO molecules on the (110) step sites are essentially linearly bonded, while on the (100) step sites both linearly and bridge bonded CO are observed. The comparison of these spectra with those obtained when a full coverage is attained shows that the band frequencies for CO on step sites are highly coupled with those on the terrace sites.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Shape-Dependent Electrocatalysis: Oxygen Reduction on Carbon-Supported Gold Nanoparticles

  • Erikson, Heiki
  • Sarapuu, Ave
  • Tammeveski, Kaido
  • Solla-Gullón, José
  • Feliu, Juan M.
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
Cubic, octahedral and quasi-spherical (two different particle sizes) Au nanoparticles are synthesised and dispersed in a carbon-black powder. The size and morphology of the Au nanocatalysts is confirmed by transmission electron microscopy and X-ray diffraction. Au nanospheres are approximately 5 and 30 nm in diameter, whereas the size of Au octahedra and nanocubes is approximately 40–45 nm. The electrocatalytic activity of these carbon-supported particles towards the oxygen reduction reaction (ORR) is studied in 0.5 M H2SO4 and 0.1 M KOH solutions by using the rotating-disk-electrode method. The specific activity (SA) for O2 reduction is measured, and the highest SA is observed for Au nanocubes supported on carbon. The highest mass activities are found for the smallest Au nanoparticles. Tafel analysis suggests that the mechanism of the ORR on shape-controlled Au/C catalysts is the same as on bulk Au.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Rapid screening of silver nanoparticles for the catalytic degradation of chlorinated pollutants in water

  • Lugaresi, Ottavio
  • Perales-Rondón, Juan V.
  • Minguzzi, Alessandro
  • Solla-Gullón, José
  • Rondinini, Sandra
  • Feliu, Juan M.
  • Sánchez-Sánchez, Carlos M.
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
Electrochemical abatement of volatile polychlorinated organic compounds for environmental applications represents a very attractive and feasible alternative for working at mild reaction conditions and reduced costs. We present herein the synthesis of three different sized Ag nanoparticles (NPs) and their electrocatalytic performance in the degradation of a model pollutant (trichloromethane, CHCl3) in aqueous media. Two different methodologies are used: A conventional study based on voltammetry and chronoamperometry and a novel screening approach based on the micropipette delivery/substrate collection (MD/SC) mode of the scanning electrochemical microscopy (SECM). This new approach allows to dose any reactant, in this case CHCl3, even if the latter cannot be electrogenerated. Moreover, we introduce here a novel platform for studying nanomaterials by reducing the current collector background contribution using disposable screen-printed array electrodes. The performance ranking obtained by the SECM for the three different samples of Ag NPs synthesized is validated by its comparison with the results obtained by chronoamperometry, which demonstrates the feasibility and the good sensitivity of SECM in electrocatalysts screening for the CHCl3 reduction reaction. In addition, SECM allows to analyze simultaneously a large number of catalysts in one single experiment under constant experimental conditions. We suggest the proper size range and the presence of abundant superficial defective sites, such as steps or kinks, as the main reasons for Ag NPs C1 exhibiting the best overall catalytic performance in trichloromethane electrochemical reduction.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

The Role of PtOH on H2O2 Interactions with Platinum Surfaces in an Electrochemical Environment

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Ethanol Oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium

  • Busó-Rogero, Carlos
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
Ethanol oxidation in 0.1 M NaOH on single-crystal electrodes has been studied using electrochemical and FTIR techniques. The results show that the activity order is the opposite of that found in acidic solutions. The Pt(111) electrode displays the highest currents and also the highest onset potential of all the electrodes. The onset potential for the oxidation of ethanol is linked to the adsorption of OH on the electrode surface. However, small (or even negligible) amounts of COads and carbonate are detected by FTIR, which implies that cleavage of the C[BOND]C bond is not favored in this medium. The activity of the electrodes diminishes quickly upon cycling. The diminution of the activity is proportional to the measured currents and is linked to the formation and polymerization of acetaldehyde, which adsorbs onto the electrode surface and prevents further oxidation.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

CO oxidation on stepped-Pt(111) under electrochemical conditions: insights from theory and experiment

  • Busó-Rogero, Carlos
  • Herrero, Enrique
  • Bandlow, Jochen
  • Comas Vives, Aleix
  • Jacob, Timo
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
The co-adsorption of CO and OH on two Pt stepped surfaces vicinal to the (111) orientation has been evaluated by means of density functional theory (DFT) calculations. Focusing on Pt(533) and Pt(221), which contain (100) and (111)-steps, respectively, we find that (111)-steps should be more reactive towards CO oxidation than surfaces containing (100)-steps. The DFT results are compared with electrochemical experiments on the CO adsorption and oxidation on these vicinal surfaces.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Oxygen reduction reaction at Pt single crystals: a critical overview

  • Gómez Marín, Ana María
  • Rizo, Rubén
  • Feliu, Juan M.
  • Rizo, Rubén|||/items/27448570-0e85-47c3-be0f-38bcb1bf11b3
Oxygen reduction reaction (ORR) dynamics at platinum single crystal surfaces is reviewed, and experimental results in acid and alkaline solutions are discussed in the framework of theoretical studies. Special emphasis is devoted to point out the role of the surface charge, water structure and adsorbed oxygen containing species. Additionally, discussion about the possible relevance of hydrogen peroxide as an intermediate species is also included. It is shown that the ORR is a complex process affected by many different factors and so neither surface charge nor oxygen-containing species coverage alone are a determining factor of the electrode activity. Instead, adlayer structures and the relation between adsorbed water, H2Oads, water dissociation products, OHads or Oads, and PtO oxide species coverage affect the whole energetics of the adsorption processes and may determine the surface reactivity. Finally, if H2O2 is an intermediate product in the ORR mechanism, it would be crucial to find a suitable catalyst able to effectively reduce H2O2 at high potentials and inhibit its oxidation.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Unusually High Activity of Pt Islands on Rh(1 1 1) Electrodes for Ethanol Oxidation

  • Del Colle, Vinicius
  • Grozovski, Vitali
  • Herrero, Enrique
  • Feliu, Juan M.
  • Herrero, Enrique|||/items/ce929130-035f-4c72-803a-a77d9c5ae46d
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Synthesis and Electrocatalytic Properties of H2SO4-Induced (100) Pt Nanoparticles Prepared in Water-in-Oil Microemulsion

  • Martínez-Rodríguez, Roberto A.
  • Vidal-Iglesias, Francisco J.
  • Solla-Gullón, José
  • Cabrera, Carlos R.
  • Feliu, Juan M.
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
The increasing number of applications for shape-controlled metal nanoparticles (NPs) has led to the need for easy, cheap, and scalable methodologies. We report the synthesis of (100) preferentially oriented Pt NPs, with a particle size of 9 nm, by using a water-in-oil microemulsion method. The specific surface structure of the NPs is induced by the presence of H2SO4 in the water phase of the microemulsion. Interestingly, the results reported herein show how increasing amounts of H2SO4 lead to the formation of Pt NPs containing a larger amount of (100) sites on their surface. This preferential surface orientation is confirmed electrochemically by using the so-called hydrogen adsorption/desorption process. In addition, transmission electron microscopy measurements confirm the presence of cubic-like Pt NPs. Finally, the electrocatalytic properties of the Pt NPs are evaluated towards ammonia and CO electro-oxidations, which are (100) structure-sensitive reactions.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Adsorption and first stages of polymerization of aniline on platinum single crystal electrodes

  • Hidalgo-Acosta, Jonnathan C.
  • Climent, Victor
  • Feliu, Juan M.
  • Climent, Victor|||/items/f8d596b7-a0df-492d-8e11-794f68d84268
The present communication studies the adsorption of aniline on platinum single crystal electrodes and the electrochemical properties of the first layers of polyaniline(PANI) grown on those platinum surfaces. The adsorption process was studied in aqueous acidic solution (0.1 M HClO4) and the electrochemical properties of thin films of PANI in both aqueous (1 M HClO4) and non-aqueous media (tetrabutyl ammonium hexafluorophosphate (TBAPF6) with additions of methanesulphonic acid in acetonitrile). First of all, it was found that the adsorption of aniline on platinum single crystal surfaces is a surface sensitive process, and even more important that the adsorption features found at low concentrations (5 × 10−5 M) can be directly correlated to the electrochemical properties of thin films of PANI in the very early stages of polymerization. The Pt(1 1 0) surface was found to be more suitable to obtain polymers with more reversible redox transitions when studied in aqueous media (1 M HClO4). This is in good agreement with the higher polymerization rates found on this surface compared to Pt(1 0 0) and Pt(1 1 1). Finally the differences in ionic exchange rate were greatly enhanced when they were studied in organic media. The AC 250 Hz response in the case of the thin films synthesized on Pt(1 1 0) is about twice greater than that obtained in the other basal planes using polymer layers with the same thickness.