Pasar al contenido principal

INTENSIFICACION DE PROCESOS EN LA OBTENCION DE COMBUSTIBLES LIQUIDOS A PARTIR DE GAS DE SINTESIS

CTQ2016-76533-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Glycerol steam reforming with low steam/glycerol ratio in a two-zone fluidized bed reactor

  • Yus, M.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
The production of hydrogen from glycerol steam reforming has been studied in several reactors. In conventional reactors the catalyst is deactivated by coke: in fixed bed reactors plugging was observed if a low steam/glycerol ratio was employed, while in fluidized bed reactors it was possible to operate for a longer time-on-stream. The use of a two-zone fluidized bed reactor is studied in this work, as a method to counteract the problem of catalyst deactivation by coke. The glycerol reforming takes place in the upper part of this reactor while the catalyst is simultaneously regenerated in the lower part, where a stream of a regenerating gas is introduced. It has been found that CO2, O2 or H2O can act as regenerating gas in a two-zone-fluidized bed reactor, allowing steady state operation at a water:glycerol molar ratio as low as 1.25. The effect of the operating conditions has been studied and the yield to the main products was compared with the calculated values assuming thermodynamic equilibrium.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Preliminary study on the feasibility of using a zeolite A membrane in a membrane reactor for methanol production

  • Gorbe, J.
  • Lasobras, J.
  • Francés, E.
  • Herguido, J.
  • Menéndez, M.
  • Kumakiri, I.
  • Kita, H.
The permeation of a mixture containing H2, CO2 and water through a zeolite membrane was studied under several operating conditions. The aim was to obtain insight on the feasibility of using such membrane in a zeolite membrane reactor for CO2 hydrogenation to methanol. The effects of total pressure (100–270 kPa), water partial pressure (10–18 kPa) and temperature (160–260 °C) were studied. Promising water-permanent gas separation factors were obtained up to 240 °C. A surprisingly high water partial pressure was found in the permeate in some cases, which is explained by the radial temperature gradient in the experimental system. The good capability of this zeolite A membrane to selectively separate water vapor makes it a promising material for its use in a zeolite membrane reactor.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Polymer–ceramic composite membranes for water removal in membrane reactors

  • Juárez, Ester
  • Lasobras Laguna, Javier
  • Soler, Jaime
  • Herguido, Javier
  • Menéndez, Miguel
Methanol can be obtained through CO2 hydrogenation in a membrane reactor with higher yield or lower pressure than in a conventional packed bed reactor. In this study, we explore a new kind of membrane with the potential suitability for such membrane reactors. Silicone–ceramic composite membranes are synthetized and characterized for their capability to selectively remove water from a mixture containing hydrogen, CO2, and water at temperatures typical for methanol synthesis. We show that this membrane can achieve selective permeation of water under such harsh conditions, and thus is an alternative candidate for use in membrane reactors for processes where water is one of the products and the yield is limited by thermodynamic equilibrium.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Modifications in the composition of cuo/zno/al2o3 catalyst for the synthesis of methanol by co2 hydrogenation

  • Trifan, Bianca
  • Lasobras Laguna, Javier
  • Soler, Jaime
  • Herguido, Javier
  • Menéndez, Miguel
Renewable methanol, obtained from CO2 and hydrogen provided from renewable energy, was proposed to close the CO2 loop. In industry, methanol synthesis using the catalyst CuO/ZnO/Al2O3 occurs at a high pressure. We intend to make certain modification on the traditional catalyst to work at lower pressure, maintaining high selectivity. Therefore, three heterogeneous catalysts were synthesized by coprecipitation to improve the activity and the selectivity to methanol under mild conditions of temperature and pressure. Certain modifications on the traditional catalyst Cu/Zn/Al2O3 were employed such as the modification of the synthesis time and the addition of Pd as a dopant agent. The most efficient catalyst among those tested was a palladium-doped catalyst, 5% Pd/Cu/Zn/Al2O3. This had a selectivity of 64% at 210 °C and 5 bar.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Methanol to Gasoline (MTG): preparation, characterization and testing of HZSM-5 zeolite-based catalysts to be used in a fluidized bed reactor

  • Sanz-Martínez, A.
  • Lasobras, J.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
The preparation of catalysts suitable for MTG processes in a fluidized bed reactor has been studied with emphasis on improving the textural, physico-chemical, morphological, structural and mechanical properties. A mixture of HZSM-5 zeolite (active material), boehmite or bentonite (binder) and alumina (inert filler) was used to prepare different catalysts. After preparation, characterization by physical adsorption of N2, XRF, XRD and SEM-EDX techniques was carried out. The screening of catalysts was performed in a fluidized bed reactor. The distribution of products was very similar in all cases, with the yield of light hydrocarbons always being higher than that of gasoline. Among the catalysts tested, the one containing boehmite as a binder (HZ_Boeh) was found as the most appropriate due to its high mechanical strength, high yield to aromatics and lower yield to durene.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Conventional and improved fluidized bed reactors for dry reforming of methane: Mathematical models

  • Zambrano, D.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
Dry reforming of methane is a potentially useful reaction, but has some drawbacks: catalyst deactivation by coke and yield limited by thermodynamic equilibrium. New improved fluidized bed reactors may compensate these disadvantages. Mathematical models for the dry reforming of methane in three types of fluidized bed reactors have been developed. These reactors include: a) conventional fluidized bed reactor, b) two zone fluidized bed reactor, which provides simultaneous reaction and catalyst regeneration in a single fluidized bed, and c) two-zone fluidized bed reactor with hydrogen selective membranes, which in addition to the previous one provides increased yield to hydrogen, because the selective removal of hydrogen through the membrane. The situations where these reactors counteract the two main drawbacks of dry reforming of methane are shown. Comparison with previous experimental results shows that the models predict well the effect of operating conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

MTO with SAPO-34 in a Fixed-Bed reactor: deactivation profiles

  • Zapater, Diego
  • Lasobras, Javier
  • Soler, Jaime
  • Herguido, Javier
  • Menéndez, Miguel
Methanol-to-olefins is a promising process that has attracted the attention of many research groups in the last years. Zeolites are the primary catalyst for this process, and SAPO-34 is one of the most used because of its high selectivity toward C2-C4 olefins. As a drawback, it deactivates quickly and forces the process to work alternately using reaction and regeneration cycles. The mechanism by which SAPO-34 deactivates is still on debate, and further research needs to be done. In this study, the evolution of the deactivation profile for an SAPO-34-based catalyst was studied in a fixed-bed reactor. To achieve that, the catalyst bed was extracted after each experiment and divided in sections of 2 cm. For each section, CO2 adsorption, thermogravimetric analysis, and ammonia temperature-programmed desorption were performed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Methanol to gasoline (MTG): Parametric study and validation of the process in a two-zone fluidized bed reactor (TZFBR)

  • Sanz-Martínez, A.
  • Lasobras, J.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
Methanol to Gasoline (MTG) process transforms methanol to hydrocarbons within the boiling point range of gasoline. The result is a wide spectrum of products (olefins, paraffins, aromatics and naphthenics, among others), with the total conversion of methanol to hydrocarbons and water. Catalyst deactivation by coke is a main problem in this process. This work aims to determine the feasibility of carrying out the production of gasoline from methanol in a two-zone fluidized bed reactor (TZFBR). The hypothesis is that the formation of carbonaceous deposits (coke) on the catalyst particles can be counteracted by its combustion in the regeneration zone that this novel reactor presents, thus achieving stable and continuous operation. In this way, both processes (reaction and regeneration) would be being carried out simultaneously in the same reactor (process intensification). The comparison of results between a conventional fluidized bed reactor and a TZFBR shows that the second one actually provides a better stability over time.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of Thermal, Acid, and Alkaline Treatments over SAPO-34 and Its Agglomerated Catalysts: Property Modification and Methanol-to-Olefin Reaction Performance

  • Zapater, Diego
  • Lasobras, Javier
  • Zambrano, Naydu
  • Hita, Idoia
  • Castaño, Pedro
  • Soler, Jaime
  • Herguido, Javier
  • Menéndez, Miguel
SAPO-34 zeolite is one of the most well-studied methanol-to-olefin catalysts, with applications from laboratory to commercial scale. Here, we have studied the impact on the properties and performance of different modifications of a commercial zeolite, including thermal, acid, and alkaline treatments, along with its agglomeration with bentonite and alumina required in the technical catalyst. We prepared three zeolites and agglomerated them, making a total of seven materials, along with our benchmark catalyst. These were characterized and tested in a packed bed reactor. We analyzed the conversion, yield, and deactivation (coke) based on the effective acid site density ρAS* (a parameter correlating acid strength, density, and micropore volume). Thermal treatment increased the effective acid site density of the commercial zeolite by 60%, while only a 10% increase was found in the parent agglomerated catalyst. Acid etching increased the effective acid site density by 80%, while the basic treatment completely amorphized the framework of the zeolite. After agglomeration, the performance of the catalysts (by means of olefin production and deactivation) correlated with effective acid site density. The catalysts based on thermally and acid-treated zeolites performed best, while they had the lowest effective acid site density.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Comparison of Conventional and Two-Zone Fluidized Bed Reactors for Methanol to Olefins. Effect of Reaction Conditions and the Presence of Water in the Feed

  • Zapater, D.
  • Lasobras, J.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
The effect of water over the performance of the Methanol-to-Olefins process was studied in a conventional fluidized bed reactor (CFBR) and a two-zone fluidized bed reactor (TZFBR). Both of them contained the same SAPO-34-based catalyst, prepared by agglomeration with bentonite and alumina. In the first section of this paper, the performance was studied in the TZFBR for a wide range of temperatures (350-600 °C, ¿T = 50 °C), and two oxygen concentrations fed to the lower zone (7.5 and 10.8% for 500, 550, and 600 °C). In the second section, a comparison between the performance over the two previously mentioned reactors is presented, followed by a comparison between feeding water or not doing so to the TZFBR. Results showed that the TZFBR increased the initial yield to olefins and the production time of them, an effect that was increased by feeding a mixture of methanol-water (1:1 molar ratio) instead of pure methanol.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Zeolite membranes: Comparison in the separation of H2O/H2/CO2 mixtures and test of a reactor for CO2 hydrogenation to methanol

  • Raso, R.
  • Tovar, M.
  • Lasobras, J.
  • Herguido, J.
  • Kumakiri, I.
  • Araki, S.
  • Menéndez, M.
A zeolite membrane reactor can be employed for hydrogenation of CO2 to methanol. The removal of water from the reaction environment would increase the reaction rate and the achievable conversion. The separation of water from mixtures containing CO2, hydrogen and water at suitable temperatures for this reaction was tested with several zeolite membranes (zeolite A, mordenite, zeolite T, chabazite and Ti-Chabazite). Zeolite A provided the best H2O/H2 separation factor. Preliminary experiments comparing a traditional reactor and the combination of a traditional reactor with a membrane reactor show that the yield of methanol was improved, in one case being higher than the limit corresponding to the thermodynamic equilibrium in a conventional reactor.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Counteracting SAPO-34 catalyst deactivation in MTO process using a two zone fluidized bed reactor: Reactor testing and process viability

  • Zapater, D.
  • Lasobras, J.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
Deactivation of SAPO-34 catalyst is a common problem in methanol to olefins (MTO) process. Due to its shape selectivity to olefins, SAPO-34 is one of the best zeolites for this purpose, but this advantage also makes its deactivation faster and more pronounced due to pore blockage or coke formation. Commonly, deactivation can be reduced by feeding water alongside with methanol, but this option only reduces but does not fully avoids deactivation. To solve this problem, we propose the use of a reactor in which reaction and regeneration of the catalyst take place simultaneously in the same unit. In this work, the comparison between conventional (CFBR) and two zone (TZFBR) fluidized bed reactors is presented, as well as a parametric study of some of the most important variables that define the TZFBR operation.