Pasar al contenido principal

ESTUDIO Y DESARROLLO DE NUEVAS TECNOLOGIAS PARA SU APLICACION EN LA FABRICACION DE IMPLANTES

DPI2013-45201-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT DE GIRONA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Breast Cancer Stem Cell Culture and Enrichment Using Poly("-Caprolactone) Scaffolds

  • Palomeras Pairet, Sònia
  • Rabionet Díaz, Marc
  • Ferrer Real, Inés
  • Sarrats Carbó, Ariadna
  • Garcia-Romeu, Maria Luisa
  • Puig i Miquel, Teresa
  • Ciurana, Quim de
The cancer stem cell (CSC) population displays self-renewal capabilities, resistance to conventional therapies, and a tendency to post-treatment recurrence. Increasing knowledge about CSCs’ phenotype and functions is needed to investigate new therapeutic strategies against the CSC population. Here, poly(ε-caprolactone) (PCL), a biocompatible polymer free of toxic dye, has been used to fabricate scaffolds, solid structures suitable for 3D cancer cell culture. It has been reported that scaffold cell culture enhances the CSCs population. A RepRap BCN3D+ printer and 3 mm PCL wire were used to fabricate circular scaffolds. PCL design and fabrication parameters were first determined and then optimized considering several measurable variables of the resulting scaffolds. MCF7 breast carcinoma cell line was used to assess scaffolds adequacy for 3D cell culture. To evaluate CSC enrichment, the Mammosphere Forming Index (MFI) was performed in 2D and 3D MCF7 cultures. Results showed that the 60° scaffolds were more suitable for 3D culture than the 45° and 90° ones. Moreover, 3D culture experiments, in adherent and non-adherent conditions, showed a significant increase in MFI compared to 2D cultures (control). Thus, 3D cell culture with PCL scaffolds could be useful to improve cancer cell culture and enrich the CSCs population, This work was supported partially by Spanish grants from Fundación Ramón Areces, Instituto de Salud Carlos III (PI1400329) and Ministerio de Economía Y Competitividad (DPI2013-45201-P), and the support of the Catalonian government (2014SGR00868). The authors are grateful for the financial support from the University of Girona (MPCUdG2016/036)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Electrospinning PCL Scaffolds Manufacture for Three-Dimensional Breast Cancer Cell Culture

  • Rabionet Díaz, Marc
  • Yeste Oliveras, Marc
  • Puig i Miquel, Teresa
  • Ciurana, Quim de
In vitro cell culture is traditionally performed within two-dimensional (2D) environments, providing a quick and cheap way to study cell properties in a laboratory. However, 2D systems differ from the in vivo environment and may not mimic the physiological cell behavior realistically. For instance, 2D culture models are thought to induce cancer stem cells (CSCs) differentiation, a rare cancer cell subpopulation responsible for tumor initiation and relapse. This fact hinders the development of therapeutic strategies for tumors with a high relapse percentage, such as triple negative breast cancer (TNBC). Thus, three-dimensional (3D) scaffolds have emerged as an attractive alternative to monolayer culture, simulating the extracellular matrix structure and maintaining the differentiation state of cells. In this work, scaffolds were fabricated through electrospinning different poly("-caprolactone)-acetone solutions. Poly("-caprolactone) (PCL) meshes were seeded with triple negative breast cancer (TNBC) cells and 15% PCL scaffolds displayed significantly (p < 0.05) higher cell proliferation and elongation than the other culture systems. Moreover, cells cultured on PCL scaffolds exhibited higher mammosphere forming capacity and aldehyde dehydrogenase activity than 2D-cultured cells, indicating a breast CSCs enrichment. These results prove the powerful capability of electrospinning technology in terms of poly("-caprolactone) nanofibers fabrication. In addition, this study has demonstrated that electrospun 15% PCL scaffolds are suitable tools to culture breast cancer cells in a more physiological way and to expand the niche of breast CSCs. In conclusion, three-dimensional cell culture using PCL scaffolds could be useful to study cancer stem cell behavior and may also trigger the development of new specific targets against such malignant subpopulation, This work was supported partially by Spanish grants from Fundación Ramón Areces, Instituto de Salud Carlos III (PI1400329) and Ministerio de Economía Y Competitividad (DPI2013-45201-P; RYC-2014-15581), and the support of the Catalonian government (2014SGR00868). The authors are grateful for the financial support from the University of Girona (MPCUdG2016/036)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Electrospinning Parameters Selection to Manufacture Polycaprolactone Scaffolds for Three-dimensional Breast Cancer Cell Culture and Enrichment

  • Rabionet Díaz, Marc
  • Puig i Miquel, Teresa
  • Ciurana, Quim de
Only a small cell population of a breast tumour presents stem cell characteristics, thus so-called breast cancer stem cells (BCSCs). BCSCs are tumour-initiating cells and chemoresistant and they can grow in non-adherent conditions as mammospheres. Study of BCSCs is a challenge due to their low representation and the inability to propagate them without inducing differentiation. Previous studies have demonstrated that three-dimensional (3D) cell culture models such as scaffolds enhance the BCSCs population. In this project, scaffolds were fabricated by electrospinning technology. Specific values of voltage and flow rate were fixed to electrospun 7.5 and 15% poly(ɛ-caprolactone) (PCL) solutions according to process stability. Both scaffolds were seeded with MCF-7 breast cancer cells and 7.5% meshes displayed lower cell proliferation compared with 15% scaffolds. Cells cultured in both scaffolds presented a significant Mammosphere Forming Index (MFI) increase, thus indicating a BCSCs enrichment. Results show that three-dimensional cell culture with electrospun 15% PCL scaffolds could be useful to expand BCSCs population facilitating the future development of new therapeutic strategies against this tumour subpopulation, This work was funded partially by Spanish grants from Fundación Ramón Areces, Instituto de Salud Carlos III (PI1400329) and by European Regional Development Fund (FEDER) and Ministerio de Economía y Competitividad (DPI2013-45201-P) and the support of the Catalonian government (2014SGR00868)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Spectrum Transmission Measurement of a Fiber Laser Beam in Polymethyl Metacrylate for Laser Sintering Processing

  • Monroy, Karla P.
  • Pupo, Yurivania
  • Serenó, Lídia
  • Ciurana, Quim de
A novel procedure is applied to evaluate the performance of Polymethyl Metacrylate (PMMA) plates as a pass through window for laser beam transmission, as a part of laser sintering machine construction. The method for laser beam spectrum transmission measurement consists basically in the exposure of a Kapton polyamide film, with the laser in a pulsed mode, in order to obtain variance diameter measurements. Measurements were analyzed in matched paired experiment levels in order to evaluate the effect of the laser beam transmission through the plates. A negligible effect of the presence of PMMA during the process was found. Selection of this polymer was then validated in performance, besides it owns transparency for purposes of process control and stable properties under harsh environmental conditions. Nevertheless, optical state of the material needs to be preserved in order to ensure consistent results in a long term, The authors gratefully appreciate the financial supports from the National Council of Science and Technology (CONACYT) and the Secretary of Public Education (SEP) in Mexico that leaded to these research results. Additionally, this investigation has been partially supported by the Project DPI2013-45201-P of the Spanish Ministry of Economy and Competitiveness
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Effect of fibre laser process on in-vitro degradation rate of a polycaprolactone stent a novel degradation study method

  • Guerra Sánchez, Antonio
  • Ciurana, Quim de
In this paper, the authors present the effect of input energy density of Nd:YAG fibre laser upon the degradation rate of the polycaprolactone. The degradation study were carried out with a novel in-vitro method closer to body conditions and were compared with the traditional in-vitro method. This approach was not presented in the available literature. The degradation rate of biodegradable stents is one of the most importance factor upon making these devices, due to it is the property in charge to provide the appropriate period of time to heal the atherosclerosis. The research for a degradable material that shows mechanical properties similar to the current permanent stents in the market and an appropriate degradation rate is still an open challenge. The literature has shown the degradation rate of some biodegradable materials before stent manufacturing's process employing in-vitro degradation methods in static flow conditions which does not match properly with the real body conditions where the blood flow circulate by the vessel. The laser cut samples were analysed by Scanning Electron Microscopy (SEM), Optical Microscopy, and weighing in order to study the effect of laser process, and degradation method over the degradation rates, surface morphology changes, and geometric pattern changes in the stent. Results have shown the influence of the laser process over the degradations rate, accelerating it according the input energy density increases. The dynamic method has increased the weight of samples, fact that will accelerate the degradations rate in a medium period of time that prove the differences that will exist in body conditions, The first authors acknowledge the financial support from University of Girona (UdG) and the Ministry of Economy and Competitiveness (MINECO), Spain for its PhD scholarship and grants from DPI2013-45201-P. The authors are grateful for the financial support from the University of Girona (Spain)MPCUdG2016/036
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Study of the Ultrasonic Molding Process Parameters for Manufacturing Polypropylene Parts

  • Negre Gubau, Paula
  • Grabalosa Saubí, Jordi
  • Ferrer Real, Inés
  • Ciurana, Quim de
Applications of polymeric materials are becoming a huge opportunity to innovate in new manufacturing technologies. In this sense Ultrasonic Molding (USM) process is an innovative technology to produce polymeric micro parts. Here, ultrasonic energy is used for melting polymeric pellets and fill a mold cavity. This paper presents a preliminary study to analyse the influence of three process parameters of USM on filling cavity, porosity, part weight and dimension. The process parameters studied are: humidity of the pellets, sonotrode velocity and mold temperature. The results show that dried pellets, velocities lower than 7mm/s or using increasing ramps velocities provide better parts. Although in future works the effect of the ultrasonic time on filling cavity and part dimensions should be studied and more material tested to extend the knowledge to this new technology, The authors would like to express their gratitude to the ULTRASION SL for their support, assistance and narrow collaboration in this research, to the Mechanical Engineering and Industrial Construction department of the University of Girona, and to Consejo Nacional de Ciencia y Tecnología de México (Conacyt). The project was developed with the DPI2013-45201-P reference grant awarded by the Spanish Government
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optimization of Poli(ϵ-caprolactone) Scaffolds Suitable for 3D Cancer Cell Culture

  • Giró Perafita, Ariadna
  • Rabionet Díaz, Marc
  • Puig i Miquel, Teresa
  • Ciurana, Quim de
Fused Deposition Model (FDM) as Additive manufacturing (AM) technologies may offer a viable and simpler alternative to manufacture scaffolds for different purposes such as tissue engineering and cells culture. Existing commercial FDM machines are currently being modified to improve their accuracy, capabilities and use. However, for biocompatible and/or bioimplantable materials such as Poli (ϵ -caprolactone) PCL there is still a lot of work to do to set up process parameters. Cells culture had been carried on 2D without being a proper and real midst. In fact cells do not grow only in two flat directions but in all directions making strong net. Since cells responses to proteins or drugs is important for knowing proliferation or enrichment more real culture in 3D is needed. This work focuses on the study and optimization of open-source 3D printer machine, called RepRap, employed to manufacture biocompatible scaffolds for 3D cells culture of Triple-Negative Breast Cancer (TNBC). It has been shown that scaffolds culture can enhance the Cancer Stem Cell (CSC) population, responsible in part for tumour recurrence after chemotherapy. Mammosphere Forming Index (MFI) was defined in all cell lines to evaluate this population in TNBC cell lines sensible and resistant to chemotherapy. Enriching TNBC cells with CSC after scaffold culture will help to study new therapeutic treatments directed to this population. Several process parameters are tested to manufacture scaffolds and cells culture had been carried out in order to validate the results. Results show that porosity plays an important role in scaffolds manufacture having low cells adhesion and growth. Lower porosity values should be tested to further evaluate MFI index after scaffold culture as cell growth and enrichment indication, This work was supported in part by Spanish Grants: Fundación Ramón Areces (TP), Instituto de Salud Carlos III (PI1400329, TP), Ministerio de Economía i Competitividad (DPI2013-45201-P), and the support of Catalonian Government (2014SGR00868). Marc Rabionet is the recipient of a Departmental Collaboration Grant from the Ministerio de Educación Cultura y Deportes of Spain for the academic years 2014-2015
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of processing conditions on manufacturing polyamide parts by ultrasonic molding

  • Ciurana, Quim de
  • Grabalosa Saubí, Jordi
  • Ferrer Real, Inés
  • Elías-Zúñiga, Alex
Ultrasonic molding is a new manufacturing process for producing small and micro polymeric components where the material is plasticized using vibration energy. In small parts manufacturing, replicability is usually demanded. Downscaled tensile specimens were manufactured using ultrasonic molding on polyamide pellets not only to obtain specimens, but also to investigate the influence of the processing conditions on process performance and material characterization. A modeling approach is proposed to assess the energy flow involved in the process. It was observed that 300 mg of polyamide could be plasticized and injected in less than 3 s and the results showed a relationship between the processing conditions and the final product, i.e. the higher the values of applied pressure, ultrasonic time and vibration amplitude, the more accurate and more homogeneous parts were. Moreover, the material did not suffer chemical degradation, but light variation on the molecular weight and different chain alignment along the specimen were detected. The mechanical properties measured were slightly influenced by the processing conditions and were in accordance with what would be expected for that particular material when being processed using conventional injection molding, The project was carried out under the DPI2013-45201-P reference grant awarded by the Spanish Government and with the financial support from the University of Girona (Spain) MPCUdG2016/036, and to the Consejo Nacional de Ciencia y Tecnología de México (CONACYT), Project Number 242269
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

New method for medical devices design and manufacture: Case study-scapholunate implant

  • Ferrer Mallorquí, Inès
  • Grabalosa Saubí, Jordi
  • Salvador, Antoni
  • Elías-Zúñiga, Alex
  • Ciurana, Quim de
The scapholunate interosseous ligament is located between the scaphoid and lunate bones and if it torns causes instability, leading to weakness in the hand, chronic pain, and lack of motion. While many treatment options are available, based on the type of instability, all of them present side effects including stiffness in the wrist, long recovery times, and widespread scarring. As such, wrist prostheses have been introduced as an alternative treatment. As suitable scapholunate prostheses implanted using arthroscopy are a promising option in reducing complications associated with conservative treatments, this work proposes a new implant designed to replace the scapholunate ligament. The implant is a completely new design, which was manufactured to determine its workability. Medical experts and engineers approved and validated the new design process, and the prototype obtained will be used to evaluate performance and to propose possible future improvements, This study received financial support from the University of Girona (UdG) and the Ministry of Economy and Competitiveness (MINECO) through the grants MPCUdG2016/036 and DPI2013-45201-P, respectively
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fibre laser cutting of polycaprolactone sheet for stents manufacturing: a feasibility study

  • Guerra Sánchez, Antonio
  • Farjas Silva, Jordi
  • Ciurana, Quim de
The role of the stent is temporary and it is limited to the intervention and shortly thereafter. Bioresorbable polymer stents were introduced to overcome this problem, making the stent manufacturing process rather difficult considering the complexity of the material. The stent forecast sale makes constant technology development necessary on this field. The adaptation of the laser manufacturing industry to these new materials is costly, thus further studies employing different sorts of lasers are necessary. This paper aims to explore the feasibility of 1.08 µm wavelength fibre laser to cut polycaprolactone sheet, which is especially interesting for long-term implantable devices, such as stents. The laser cut samples were analysed by Differential Scanning Calorimetry (DSC), Tensile Stress Test, and Optical Microscopy in order to study the effects of the laser process over the workpiece. The parameters measured were: taper angle, dimensional precision, material structure changes and mechanical properties changes. Results showed a dimensional precision above 95.75% with a taper angle lower than 0.033°. The laser ablation process has exhibited a minor influence upon material properties. Results exhibit the feasibility of fibre laser to cut polycaprolactone, making the fibre laser an alternative to manufacture stents, The authors acknowledge the financial support from Ministry of Economy and Competitiveness (MINECO), Spain for its PhD scholarship and grants from DPI2013-45201-P and University of Girona (UdG), Spain MPCUdG2016/036
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fabrication of PCL/PLA Composite Tube for Stent Manufacturing

  • Guerra Sánchez, Antonio
  • San Molina, Joan
  • Ciurana, Quim de
This work presents the effect of Dip Coating process over the tube's features to obtain a PCL/PLA tube to stent purpose. The effects of withdrawal speed, number of cycles, and solutions concentration were studied. Four different tubes were fabricated and analyzed by Dynamic Mechanical Analysis (DMA), Degradation Rate, Surface Roughness, Thickness, and Uniformity. Results have shown the strong influence of withdrawal speed and polymer's concentration over the tube's features. DMA and degradation results showed the limitations of PCL and PLA as material for the stent purpose, meanwhile the PCL/PLA composite tube showed a behavior closer to the stents requirements, The authors acknowledge the financial support from Ministry of Economy and Competitiveness (MINECO), Spain for its PhD scholarship and grants from DPI2013-45201-P and University of Girona (UdG), Spain MPCUdG2016/036
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A novel 3D additive manufacturing machine to biodegradable stents

  • Guerra Sánchez, Antonio
  • Roca Calm, Albert
  • Ciurana, Quim de
Biodegradable stents offer the potential to improve long-term patency rates by providing support just long enough for the artery to heal. However, design a biodegradable structure for an intended period of support is rather difficult. Nowadays in the stent industry the manufacture process par excellence is the laser micro cutting. Nevertheless in the case of polymeric stents, the 3D additive manufacturing techniques could be a more economical solution. This work aim to design and implement a novel 3D Additive Manufacturing Machine to Biodegradable Stent Manufacture. The effects of nozzle temperature, fluid flow, and printing speed over the polycaprolactone stent’s precision is studied. Results have shown the strong influence of temperature and flow rate over the printing precision. Printing speed did not had a clear tendency. The results allow us to believe that the novel technology presented in this paper will be an interesting future research line, The authors acknowledge the financial support from Ministry of Economy and Competitiveness (MINECO), Spain for its PhD scholarship and grants from DPI2013-45201-P and University of Girona (UdG), Spain MPCUdG2016/036.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

3D-printed Tubular Scaffolds for Vascular Tissue Engineering

  • Rabionet Díaz, Marc
  • Guerra Sánchez, Antonio
  • Puig i Miquel, Teresa
  • Ciurana, Quim de
Biomedical engineering is the application of engineering principles and design concepts to medicine and biology for healthcare purposes. Much of the work in biomedical engineering consists of research and development, spanning a broad array of subfields like biomechanics, genetic, neural, pharmaceutical, medical devices and tissue engineering among others. Tissue engineering has emerged as a key discipline for organ and tissue regeneration, in which compatibility with final user and a fast regeneration are still major challenges. Recently, three-dimensional printing has arose as an alternative system for producing biomaterials devices, such as scaffolds for tissue engineering. The proliferation of murine fibroblasts NIH/3T3, widely used in tissue engineering studies, into polycaprolactone scaffolds has been assayed in this paper. This work aim to analyze the effect of different architectures of 3D tubular scaffolds with empty core on fibroblast proliferation, focusing the tissue engineering application. We determined the effect of manufacturing process parameters and scaffold design onto the cell proliferation. From results, it can be concluded that manufacturing parameters (printing speed, temperature, and flow rate) affected fibroblast growth rate up to 40-65%. Narrow pores produced by an increased material extrusion showed less fibroblast growth, possibly due to a hindered oxygen and nutrient exchange. Nevertheless, future experiments using different designs and scaffold's architecture must be done, The authors acknowledge the financial support from the Ministry of Economy and Competitiveness (MINECO), Spain for its PhD scholarship and grants from DPI2013-45201-P and RYC-2014-15581 and the financial support from the University of Girona (Spain) MPCUdG2016/036. This work was also supported partially by Spanish grants from Fundación Ramón Areces and Instituto de Salud Carlos III (PI1400329)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Assessing a stepped sonotrode in ultrasonic molding technology

  • Grabalosa Saubí, Jordi
  • Ferrer Real, Inés
  • Martínez-Romero, Oscar
  • Elías-Zúñiga, Alex
  • Plantá, X.
  • Rivillas, F.
Ultrasonic molding is a new technology used to process polymeric micro-molded parts. An ultrasonic horn, or sonotrode, transmits ultrasonic energy which melts the material and pushes it into a mold cavity to configure a shape. Sonotrode design - and any transformations to the dimensions or shape caused by tool wear - strongly affects efficient operation. The sonotrode may go beyond the generator operating frequency range, thus affecting process performance. This paper assesses two issues involving a stepped sonotrode employed in ultrasonic molding: (i) a design procedure that can predict the sonotode's behavior during the molding process and (ii) a method for creating a sonotrode operating frequencies map which will facilitate the design of new sonotrodes and be able to determine the extent to which they can be re-machined after a certain period of wear. Numerical simulations carried out by finite element methods were compared to experimental measurements performed to capture the sonotrode frequency vibrational modes. A frequency map provides the dimensional range within which the sonotrode can be re-machined in order to eliminate tool wear and allow the sonotrode to work properly again, thus extending the lifecycle of the tool, This project was carried out with the helpof a DPI2013-45201-P reference grant awarded by the Spanish Gov-ernment