Pasar al contenido principal

MODELADO Y CONTROL DEL PROCESO COMBINADO DE PRODUCCION DE MICROALGAS Y TRATAMIENTO DE AGUAS RESIDUALES CON REACTORES INDUSTRIALES

DPI2017-84259-C2-2-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD NACIONAL DE EDUCACION A DISTANCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Robust switched control of an air levitation system with minimum sensing

  • Chaos, D.
  • Chacón Sombría, Jesús
  • Aranda Escolástico, E.
  • Dormido, S.
This work studies the control problem of an air levitation system with limited sensing capabilities. We propose a simple but considerably robust switched controller. We prove that the output of the system is globally uniformly ultimately bounded with a bound as small as we desire and we show through simulations and real experiments the robustness of the controller in the presence of disturbances, model uncertainties and parameter tuning.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Identificación de sistemas de primer y segundo orden mediante control basado en reset, Identification of first and second order systems by reset control

  • Zaragoza, S.
  • Sanchez, J.
  • Baños, A.
[EN] The article presents a method for the identification of first and second order processes with time delay using reset controllers in the absence of disturbances. The method is based on compliance with the method of harmonic balance, which implies the use of an approximation of the control reset by its describing function. The FORE controller (First Order Reset Element) with fixed bandwidth has been chosen because it is the easiest reset driver that possesses all the inherent characteristics in this type of drivers and its descriptive function depends on the amplitude and frequency of its sinusoidal signal input. On the other hand, the fact that the behavior of this reset driver depends on of its reset band allows studying the impact of this parameter in the identification process and in its accuracy., [ES] El artículo presenta un método para la identificación de plantas de primer y segundo orden con retardo usando controladores reseteados en ausencia de perturbaciones. El método se basa en el cumplimiento del principio de equilibrio armónico, lo que implica el uso de una aproximación del controlador reseteado mediante su función descriptiva. Para la realización de este trabajo se ha elegido el controlador FORE (First Order Reset Element) con banda de reset porque es el controlador reseteado que posee todas las características intrínsecas de este tipo de controladores y presenta una función descriptiva que depende de la amplitud y frecuencia de la señal sinusoidal de su entrada. Por otro lado, el que el comportamiento de este controlador dependa de la anchura de la banda de reset que se haya fijado permite estudiar el impacto de este parámetro en el proceso de identificación y en su precisión., Este trabajo ha sido realizado parcialmente gracias al apoyo del Ministerio de Economía y Competitividad de España a través de los fondos asignados a los proyectos DPI2017-84259-C2-2-R y DPI2016-79278-C2-1-R.
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

A practical approach to adaptive sliding mode control

  • González, José Antonio
  • Barreiro Blas, Antonio
  • Dormido Bencomo, Sebastián
This paper is concerned with the development of a practical approach to the design of adaptive sliding mode controllers. The objective is to define an adaptive control law that presents some desired advantages such as non overestimation of the disturbance input, cancellation of the chattering phenomenon, zero overshooting response, avoid control saturation and simplicity of algorithm tuning. In this practical approach a solution is provided that uses both, adaptive sliding surfaces and adaptive control gains so the proposed controller is able to manage input disturbances with bounded derivatives., Agencia Estatal de Investigación | Ref. DPI2017-84259-C2-2-R, Ministerio de Economía y Competitividad | Ref. PTQ-14-07366, Ministerio de Economía y Competitividad | Ref. DPI2016-79278-C2-2-R
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On teaching digital control systems in a generic engineering degree

  • Lerma, Eneko
  • Costa Castelló, Ramon
  • Griñó, Robert
  • Sanchis, Carlos
  • Dormido, Sebastián
Trabajo presentado en el 12th IFAC Symposium on Advances in Control Education ACE , celebrado en Philadelphia, Pennsylvania (Estados Unidos), del 7 al 9 de julio de 2019, In this work, the subject of digital control taught in a generic engineering degree is described. In particular, the contents of the course, the experimental environment and the interactive tools used in teaching are discussed. This work collects the teaching experience obtained during the past twenty years by the teaching team of this subject at the Barcelona School of Industrial Engineering of the Universitat Politecnica de Catalunya., The work of R. Costa-Castello was partially supported by the Government of Spain through the Agencia Estatal de Investigacion projects DPI2015-69286-C3-2-R and Marıa de Maeztu Seal of Excellence to IRI (MDM-2016-0656), by the Generalitat de Catalunya through the Project 2017 SGR 482 and by the donation of Mathworks UPC-I-01523. The work of R. Griño was partially supported by the Government of Spain through the Agencia Estatal de Investigaci´on Project DPI2017-85404-P, by the Generalitat de Catalunya through the Project 2017 SGR 872 and by the donation of Mathworks UPC-I-01523. The work of E. Lerma was partially supported by the donation of Mathworks UPC-I-01523. The work of S. Dormido was partially supported by the Government of Spain through the Agencia Estatal de Investigacion projects DPI2017-84259-C2-2-R.
Docta Complutense
Publicación Artículo científico (JournalArticle)

A study of strategies for developing online laboratories

  • Sáenz, Jacobo
  • Torre, Luis De La
  • Chacón Sombría, Jesús
  • Dormido, Sebastián
Researchers and teachers around the world have created newsoftware and hardware to develop, reuse, and deploy online laboratories (labs). However, due to the nature of labs, most of the available solutions depend greatly on where and how online labs can be used in the first place. Thus, there have been multiple design solutions and great technology combinations. In this study, we analyzed and studied the main obstacles in the online lab development and the alternatives of the technologies, means, methodologies, and approaches on creating online labs. The resulting analysis showed the advantages, disadvantages, and problems of each key component and attempted to explore the working combinations that ensure the usability, modularity, universality, accessibility, and reliability of online labs. In addition, we explored a general solution to take advantage of the benefits of the technologies involved in online labs and to fix or reduce the impacts of the arising problems when developing and deploying online labs.