Pasar al contenido principal

SISTEMATIZACION DE LA FABRICACION PERSONALIZADA DE MOLDES MEDIANTE FABRICACION ADITIVA 3DP Y DE SU INSPECCION CON METROLOGIA OPTICA

DPI2017-89840-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE LEÓN

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

BULERIA. Repositorio Institucional de la Universidad de León
Publicación Tesis doctoral (DoctoralThesis)

Desarrollo de la técnica aditiva de proyección de aglutinante para la fabricación rápida de moldes para fundición de metales no férreos, Development of additive binder jetting technique for rapid casting of non-ferrous metal

  • Rodríguez González, Pablo
187 p., [ES] El objetivo principal de esta tesis doctoral, es demostrar la viabilidad para poder utilizar el material en polvo de sulfato de calcio como materia prima en la técnica de proyección de aglutinante, para la producción de moldes de carcasa en el ámbito de la fundición de aluminio., Agencia Estatal de Investigación
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Feasibility of Calcium Sulfate Moulds Made by Inkjet 3D Printing for Rapid Casting of Aluminium Alloys

  • Rodríguez González, Pablo
  • Robles Valero, Pablo Eduardo
  • Fernández Abia, Ana Isabel
  • Castro Sastre, María Ángeles
  • Barreiro García, Joaquín
[EN] In this research, a comparative analysis has been carried out between a traditional sand casting process and a modern mould obtained by additive manufacturing (AM), in the context of aluminium parts production. In this case of AM, an inkjet 3D printing (3DP) process allowed us to create a ceramic mould. A numerical simulation was carried out to study the filling and cooling rates of both parts. The design freedom typical of the 3DP technique allowed us to optimize the f illing system. The results showed that in sand moulding, the speed in the gate suddenly increased when the liquid metal entered the part cavity, leading to severe turbulence due to the fountain e ect. The input of air is related to the speed in the gate. Nevertheless, the results showed that when using the 3DP mould, the speed in the gate remained constant and the filling process was homogenous. With regard to the dimensional precision, while the staircase e ect in the surface of the 3DP mould is the most critical aspect to control, in the sand casting mould the critical aspect is the dimensional precision of the pattern. Microstructures of the cross-section of the moulded parts showed folded shapes and air input in sand casting, which could be produced by the severe turbulence and the oxide f ilm present in the melt during the filling process. On the other hand, the porosity found in parts produced with the 3DP mould corresponds to shrinkage; during the filling process, the remaining binder is vaporized, creating nucleation points. In this way, pores are formed by shrinkage and a mixture of shrinkage and gas entrapment. With these considerations, it can be concluded that AM shows feasibility and advantages as an alternative to the sand casting method for aluminium alloys, SI, Agencia Estatal de Investigación
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Application of Vacuum Techniques in Shell Moulds Produced by Additive Manufacturing

  • Rodríguez González, Pablo
  • Robles Valero, Pablo Eduardo
  • Fernández Abia, Ana Isabel
  • Castro Sastre, María Ángeles
  • Barreiro García, Joaquín
[EN] This research shows the feasibility of the additive manufacturing technique (AM), Binder Jetting (BJ), for the production of shell moulds, which are filled by vacuum suction in the field of aluminium parts production. In addition, this study compares the gravity pouring technique and highlights the advantages of using vacuum techniques in AM moulds. A numerical simulation was carried out to study the behaviour of the liquid metal inside the moulds and the cooling rate of parts was analysed. The results show that in the gravity-pouring mould, the velocity in the gate causes moderate turbulence with small waves. However, vacuum suction keeps the velocity constant by eliminating waves and the filling process is homogeneous. Regarding dimensional accuracy, the staircase e ect on the surface of the 3D moulds was the most critical aspect. The vacuum provides very homogeneous values of roughness across the entire surface of the part. Similarly, 3D scanning of castings revealed more accurate dimensions thanks to the help of vacuum forces. Finally, the microstructure of the cross section of the moulded parts shows that the porosity decreases with the vacuum filled. In both cases, the origin of the pores corresponds to gas entrapment and shrinkage during the filling process, the binder vaporization and nucleation points creation, leading to pores by shrinkage, gas entrapment or a mixture of both. This is the first study that uses vacuum f illing techniques in moulds created by BJ, demonstrating the feasibility and advantages of AM using vacuum techniques, as an alternative to traditional casting., SI, Agencia Estatal de Investigación
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Towards Functional Parts by Binder Jetting Calcium-Sulphate with Thermal Treatment Post-Processing

  • Castro Sastre, María Ángeles
  • Fernández Abia, Ana Isabel
  • Piep, Janik
  • Rodríguez González, Pablo
  • Barreiro García, Joaquín
[EN] The objective of our research is to improve the properties of calcium-sulphate hemihydrate parts printed by binder jetting. In this paper, we show the thermal treatment results when using temperature time ramps on binder-jetted ceramic parts without infiltrating. The results show that the mechanical properties of printed parts are improved substantially. Two different thermal cycles were investigated for their effect on the dehydration process of CaSO4·½H2O using infrared analysis. The thermal-treated samples were compared with respect to porosity, surface roughness, compression strength and dimensional and weight variation. The proposed thermal treatment significantly improves the compression strength in a short time, guaranteeing dimensional stability while providing a good surface. This improvement in mechanical properties offers a great chance for using binder-jetted parts as functional components, for example, in the casting field or the medical sector (scaffolds)., SI, Agencia Estatal de Investigación
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Evaluation of the influence of post-processing on the optical inspection accuracy of additively manufactured parts

  • Giganto Fernández, Sara
  • Martínez Pellitero, Susana
  • Barreiro García, Joaquín
  • Cuesta González, Eduardo
[EN] Optical measurement systems are important techniques for rapid inspecting additively manufactured parts by techniques such as selective laser melting (SLM). Depending on their application, SLM parts require post-processes such as sandblasting or heat treatment, commonly applied in order to improve their surface finish or mechanical properties, respectively. These post-processes modify the parts surface characteristics, and therefore the suitability for optical inspection. This work evaluates the influence of these SLM post-processes on optical inspection. For this, a test part, manufactured in 17-4PH stainless steel using a 3DSystems ProX100 machine, was optically measured using a structured light scanner and compared to the values obtained from contact measurements (reference values). Both optical and contact measurements were performed under three conditions: as-built, post sandblasting, and post sandblasting and subsequent heat treatment. The analysis results show that applying the sandblasting postprocessing provides a surface finish to the SLM parts suitable for optical inspection. This postprocess allows precise inspection of this type of parts, reaching values close to those obtained by contact. Likewise, it is concluded that the used structured blue-light scanner is suitable for inspecting SLM parts., SI, Ministerio de Ciencia, Innovación y Universidades, Instituto Universitario de Tecnología Industrial (SV-18-1-GIJON-1-06 and SV-19-GIJON-1-14)
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Metrology Benchmarking of 3D Scanning Sensors Using a Ceramic GD&T-Based Artefact

  • Cuesta González, Eduardo
  • Meana Díaz, Víctor Manuel
  • Álvarez Álvarez, Braulio José
  • Giganto Fernández, Sara
  • Martínez Pellitero, Susana
[EN] The use of non-contact scanning equipment in metrology and in dimensional and geometric inspection applications is increasing due to its ease of use, the speed and density of scans, and the current costs. In fact, these technologies are becoming increasingly dominant in the industrial environment, thus moving from reverse engineering applications to metrological applications. However, this planned transfer requires actions to ensure the achievable accuracy by providing traceability of measurements. In the present study, a comparison between the devices is carried out and a specific standard artefact is designed, equipped with multiple ceramic optically friendly entities, and allowing a wide variety of geometric dimensioning and tolerancing (GD&T). Four different 3D scanning sensors are used in the experimentation. Three of them are based on laser triangulation, and the fourth is a structured blue light sensor (fringe pattern projection). The standard artefact is calibrated with a high accuracy, using a coordinate measuring machine (CMM) and probing sensors. With this CMM, reference values of multiple predefined GD&T are obtained. The evaluation methodology maximises the accuracy of each device in measuring the dimensions of the artefact due to the good dimensional (milling and turning), surface (control of machining variables), and the dimensional and spatial distribution characteristics. The procedure also includes the same treatment of the captured point clouds (trimming, filtering, and best-fit algorithm, etc.) in each of the four 3D scanning sensors considered. From this process, very reliable measurements of the maximum achievable accuracy of each device (deviations from the CMM measurements) are finally obtained, and a multi-characteristic comparison between the four sensors is performed, also with high reliability., SI, Ministerio de Economía, Instituto Universitario de Tecnología Industrial (SV-20-GIJON-1-03)
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Analysis of gaseous emission and particle number size distributions in metal casting processes with binder jetting moulds

  • Blanco Alegre, Carlos del
  • Calvo Gordaliza, Ana Isabel
  • Castro Sastre, María Ángeles
  • Fernández Abia, Ana Isabel
  • Rodríguez González, Pablo
  • Oduber Pérez, Fernanda Isabel
  • Castro Izquierdo, Amaya
  • Barreiro García, Joaquín
  • Fraile Laiz, Roberto
[EN] The impact on indoor air quality during metal casting processes using the 3D printing (3DP) binder jetting technique to manufacture moulds is analyzed in this research. This study investigates the particle size distribution and gas concentration during the manufacturing stages of 3DP moulds, with focus on particle deposition in the human respiratory system. The goal is to understand the risks associated with particle and gas emissions in binder jetting 3D printing, and thus improve worker safety. The results indicate that particle emission rates are lowest during printing (0.01 1011particles min−1) but increase during post-processing and melting-pouring phases (3.07 1011 particles min−1). During melting and pouring, the emission of particles was mainly in the range 7.9–71 nm, with values 10 times higher than in the previous phases. The study calculates the deposition of inhaled particles in different parts of the respiratory tract and reveals a 2.39 times higher extrathoracic mass deposition during 3DP mould manufacturing stages compared to melting-pouring stages. Additionally, alveolar mass deposition is higher during melting-pouring stages due to an increase in ultrafine emission rates. The study emphasizes the importance of insulation equipment and workplace ventilation in indoor spaces, particularly during heating processes that generate ultrafine particles through nucleation, so that health risks can be mitigated, SI, The sampling campaign was partially supported by the Spanish Ministry of Science, Innovation and Universities (Grant RTI2018-098189-B-I00), the University of León (Programa Propio 2015/00054/001 and 2018/00203/001) and the AEROHEALTH project (Ministry of Science and Innovation, Grant PID2019-106164RB-I00, co-financed with European FEDER funds). Authors thank the Ministry of Science, Innovation and Universities of Spain for the support through the research project with reference DPI2017-89840-R. Furthermore, this study is part of the project TED2021-132292 B–I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union “NextGenerationEU”/PRTR
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Automated Shrinkage and Gas Porosity Detection Using YOLO Model in Additive-Manufactured Aluminum Alloy Parts

  • Arias Martínez, Laura
  • Jáñez Martino, Francisco
  • Fidalgo Fernández, Eduardo
  • Rodríguez González, Pablo
  • Fernández Abia, Ana Isabel
  • Alegre Gutiérrez, Enrique
  • Barreiro García, Joaquín
Open access funding provided by FEDER European Funds and the Junta de Castilla y León under the Research and Innovation Strategy for Smart Specialization (RIS3) of Castilla y León 2021-2027, [EN] Developing intelligent and automatic systems to detect defects in additive manufacturing parts is still a great challenge. In this work, the binder jetting technology has been used to manufacture molds for aluminum casting, and the defects of the parts obtained in these molds have been analyzed and compared with the parts obtained in molds manufactured with the traditional sand-casting method. The main defects obtained in both casting methods have been due to porosity, which is one of the most critical defects affecting the mechanical behavior of the parts. We propose a methodology to develop an automatic system for detecting these defects in casting parts. We also presented the Porosity Detection Corpus, a novel and publicly available dataset containing 204 pictures taken after cross-sectioning the manufactured parts, 102 for each casting technique. Then, we manually annotated the bounding boxes that include gas and shrinkage pores using two different labeling: only pores and their type. Finally, we trained and evaluated a pre-trained You Only Look Once (YOLO) model on the Porosity Detection Corpus, considering different thresholds in terms of recall. For detecting unique pores, we recommended using 25% of threshold, with a recall of 0.599. For classifying the type of pore, gas or shrinkage, we recommended a threshold of 25% with a mAP of 0.377., SI