Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Utilization of phase change materials in solar domestic hot water systems

  • Mazman, Muhsin
  • Cabeza, Luisa F.
  • Mehling, Harald
  • Nogués Aymamí, Miquel
  • Evliya, Hunay
  • Paksoy, Halime Ö.
Thermal energy storage systems which keep warm and cold water separated by means of gravitational stratification have been found to be attractive in low and medium temperature thermal storage applications due to their simplicity and low cost. This effect is known as thermal stratification, and has been studied experimentally thoughtfully. This system stores sensible heat in water for short term applications. Adding PCM (phase change material) modules at the top of the water tank would give the system a higher storage density and compensate heat loss in the top layer because of the latent heat of PCM. Tests were performed under real operating conditions in a complete solar heating system that was constructed at the University of Lleida, Spain. In this work, new PCM-graphite compounds with optimized thermal properties were used, such as 80:20 weight percent ratio mixtures of paraffin and stearic acid (PS), paraffin and palmitic acid (PP), and stearic acid and myristic acid (SM). The solar domestic hot water (SDHW) tank used in the experiments had a 150 L water capacity. Three modules with a cylindrical geometry with an outer diameter of 0.176 m and a height of 0.315 m were used. In the cooling experiments, the average tank water temperature dropped below the PCM melting temperature range in about 6–12 h. During reheating experiments, the PCM could increase the temperature of 14–36 L of water at the upper part of the SDHW tank by 3–4 C. This effect took place in 10–15 min. It can be concluded that PS gave the best results for thermal performance enhancement of the SDHW tank (74% efficiency)., This study was supported by The Scientific and Technical Research Council of Turkey (TUBITAK) and The Ministry of Education and Science of Spain through the project ENE2005-08256-C02-01/ALT.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Behaviour of a concrete wall containing micro‐encapsulated PCM after a decade of its construction

  • Cabeza, Luisa F.
  • Navarro Farré, Lidia
  • Pisello, Anna Laura
  • Olivieri, Lorenzo
  • Bartolomé, Cesar
  • Sánchez Sánchez, José
  • Álvarez Domínguez, Servando
  • Tenorio, José Antonio
Today, our society has the duty of reducing the energy consumed in the building sector. A promising technology to achieve this goal is the implementation of thermal energy storage (TES) solutions in buildings envelope. Lately, much literature dealing with the effect of the inclusion of latent heat storage materials in construction materials to provide higher thermal inertia has appeared, mostly focusing on the evaluation of the thermal properties, density, or porosity of these new materials. However, few of them evaluated the long stability properties of the materials with embedded PCM when included in a building, very much needed since the lifetime of a building is about 50 years. Therefore, in this study, an evaluation of a house‐like cubicle of concrete with micro‐encapsulated PCM after a decade of its construction is carried out. The results are compared to the tests done in 2005 concluding that the thermal performance of this cubicle presented no degradation in the PCM effect., The work partially funded by the Spanish Government (ENE2015‐64117‐C5‐1‐R (MINECO/FEDER), ULLE10‐4E‐1305, and ENE2005‐08256‐C02‐01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Financiado por el proyecto RTC‐2015‐3583‐5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013‐2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Behaviour of a concrete wall containing micro‐encapsulated PCM after a decade of its construction

  • Cabeza, Luisa F.
  • Navarro Farré, Lidia
  • Pisello, Anna Laura
  • Olivieri, Lorenzo
  • Bartolomé, Cesar
  • Sánchez Sánchez, José
  • Álvarez Domínguez, Servando
  • Tenorio, José Antonio
Today, our society has the duty of reducing the energy consumed in the building sector. A promising technology to achieve this goal is the implementation of thermal energy storage (TES) solutions in buildings envelope. Lately, much literature dealing with the effect of the inclusion of latent heat storage materials in construction materials to provide higher thermal inertia has appeared, mostly focusing on the evaluation of the thermal properties, density, or porosity of these new materials. However, few of them evaluated the long stability properties of the materials with embedded PCM when included in a building, very much needed since the lifetime of a building is about 50 years. Therefore, in this study, an evaluation of a house‐like cubicle of concrete with micro‐encapsulated PCM after a decade of its construction is carried out. The results are compared to the tests done in 2005 concluding that the thermal performance of this cubicle presented no degradation in the PCM effect., The work partially funded by the Spanish Government (ENE2015‐64117‐C5‐1‐R (MINECO/FEDER), ULLE10‐4E‐1305, and ENE2005‐08256‐C02‐01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Financiado por el proyecto RTC‐2015‐3583‐5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013‐2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Utilization of phase change materials in solar domestic hot water systems

  • Mazman, Muhsin
  • Cabeza, Luisa F.
  • Mehling, Harald
  • Nogués Aymamí, Miquel
  • Evliya, Hunay
  • Paksoy, Halime Ö.
Thermal energy storage systems which keep warm and cold water separated by means of gravitational stratification have been found to be attractive in low and medium temperature thermal storage applications due to their simplicity and low cost. This effect is known as thermal stratification, and has been studied experimentally thoughtfully. This system stores sensible heat in water for short term applications. Adding PCM (phase change material) modules at the top of the water tank would give the system a higher storage density and compensate heat loss in the top layer because of the latent heat of PCM. Tests were performed under real operating conditions in a complete solar heating system that was constructed at the University of Lleida, Spain. In this work, new PCM-graphite compounds with optimized thermal properties were used, such as 80:20 weight percent ratio mixtures of paraffin and stearic acid (PS), paraffin and palmitic acid (PP), and stearic acid and myristic acid (SM). The solar domestic hot water (SDHW) tank used in the experiments had a 150 L water capacity. Three modules with a cylindrical geometry with an outer diameter of 0.176 m and a height of 0.315 m were used. In the cooling experiments, the average tank water temperature dropped below the PCM melting temperature range in about 6–12 h. During reheating experiments, the PCM could increase the temperature of 14–36 L of water at the upper part of the SDHW tank by 3–4 C. This effect took place in 10–15 min. It can be concluded that PS gave the best results for thermal performance enhancement of the SDHW tank (74% efficiency)., This study was supported by The Scientific and Technical Research Council of Turkey (TUBITAK) and The Ministry of Education and Science of Spain through the project ENE2005-08256-C02-01/ALT.