Pasar al contenido principal

ESTRUCTURAS FLEXIBLES DE CONTROL DE CONVERTIDORES ELECTRONICOS PARA PROCESADO E INTEGRACION DE ENERGIAS RENOVABLES EN MICRORREDES

ENE2009-13998-C02-02

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2009
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An adaptive synchronous-reference-frame phase-locked loop for power quality improvement in a polluted utility grid

  • González Espín, Francisco José
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
The proper operation of grid-connected power electronics converters needs using a synchronization technique to estimate the phase of the grid voltage. The performance of this synchronization technique is related to the quality of the consumed or delivered electric power. The synchronous-reference-frame phase-locked loop (SRF-PLL) has been widely used due to its ease of operation and robust behavior. However, the estimated phase can have a considerable amount of unwanted ripple if the grid voltage disturbances are not properly rejected. The aim of this paper is to propose an adaptive SRF-PLL which strongly rejects these disturbances even if the fundamental frequency of the grid voltage varies. This is accomplished by using several adaptive infinite-impulse-response notch filters, implemented by means of an inherently stable Schur-lattice structure. This structure is perfectly suited to be programmed in fixed-point DSPs (i.e., it has high mapping precision, low roundoff accumulation, and suppression of quantization limit cycle oscillations). The proposed adaptive SRF-PLL has been tested by means of the TI TMS320F2812 DSP. The obtained experimental results show that the proposed synchronization method highly rejects the undesired harmonics even if the fundamental harmonic frequency of a highly polluted grid voltage abruptly varies. © 2011 IEEE., This work was supported by the Spanish Ministry of Science and Innovation under Grants ENE2009-13998-C02-02 and ENE2006-15521-C03-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Measurement of the Loop Gain Frequency Response of Digitally Controlled Power Converters

  • González Espín, Francisco José
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • González-Medina, Raúl|||0000-0003-0378-5045
  • Pascual Molto, Marcos|||0000-0002-9337-9755
[EN] The study of the loop gain frequency response in a power converter is a powerful tool commonly used for the design of the controllers used in the control stage. As the control of medium- and high-power electronic converters is usually performed digitally, it is useful to find a method to measure the digital loop gains. The purpose of this paper is to present a method for properly measuring the loop gain frequency response of digitally controlled power converters by means of an analog frequency response analyzer (FRA). An analog sinusoidal reference signal generated by the FRA is injected through an analog-to-digital converter into the digital controller, and added to the discrete feedback signal. To obtain the frequency response of the open-loop gain, both feedback and disturbed feedback signals are sent back to the FRA by using the pulsewidth modulation peripherals of the controller., This work was supported by the Spanish Ministry of Science and Innovation under Grants ENE2006-15521-C03-02 and ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Photovoltaic Power System With Battery Backup With Grid-Connection and Islanded Operation Capabilities

  • Velasco de la Fuente, David
  • Trujillo Rodríguez, Cesar Leonardo
  • Ortega González, Rubén
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
This paper presents the analysis, design, and experimentation results of a photovoltaic energy management system with battery backup. The proposed system is capable of both grid-connected and islanded operations. The main advantage of the proposed system is that, in grid-connected mode, the inverter works as a current source in phase with the grid voltage, injecting power to the grid and controlling the dc-link voltage. The dc/dc converter manages the battery charge. In islanded mode, the inverter control is reconfigured to work as a voltage source using droop schemes. The dc/dc converter controls the dc-link voltage to enable the maximum power point tracking reference to be followed. An operation protocol is proposed to ensure the quality of the energy supply and minimize energy loss. A battery bank is connected to the dc link as energy storage for islanded operation mode. The aim of this paper is to show that the proposed system performs correctly, without dangerous transients for the inverter or the loads. Simulation and experimental results on a 3-kW prototype show the feasibility of the proposed control strategy., This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02. The translation of this paper was funded by the Universitat Politecnica de Valencia, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Peak current mode control of three-phase boost rectifiers in discontinuous conduction mode for small wind power generators

  • Carranza, O.
  • González, L.G.
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
[EN] This paper presents a peak current mode control scheme of a boost rectifier with low distortion of the input current for wind power systems based on permanent magnet synchronous generators with variable speed operation. The three-phase boost rectifier is operated in discontinuous conduction mode (DCM), and power factor correction techniques are applied. It is shown that the DCM operation significantly reduces the total harmonic distortion of the currents in the permanent magnet synchronous generator, increasing the power factor of the system, so that the vibrations and mechanical stress of the generator are minimized. The characteristics of the DCM boost rectifier are studied considering: (1) the series resistance of the inductors; (2) the modeling and adjustment of peak current mode control yielding a stable loop; (3) the design of an input filter that reduces the switching noise in the currents of the generator., This work was supported by the Spanish Ministry of Science and Innovation under Grants ENE2006- 15521-C03-02 and ENE2009- 13998-C02-02. The first author thanks the support of the Instituto Politecnico Nacional (IPN) and of the Comision de Operacion y Fomento de Actividades Academicas (COFAA) to finance his stay at the Universidad Politecnica de Valencia (UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A low-cost photovoltaic emulator for static and dynamic evaluation of photovoltaic power converters and facilities

  • González-Medina, Raúl|||0000-0003-0378-5045
  • Patrao Herrero, Iván|||0000-0003-4412-0365
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
In testing maximum power point tracking (MPPT) algorithms running on electronic power converters for photovoltaic (PV) applications, either a PV energy source (PV module or PV array) or a PV emulator is required. With a PV emulator, it is possible to control the testing conditions with accuracy so that it is the preferred option. The PV source is modeled as a current source; thus, the emulator has to work as a current source dependent on its output voltage. The proposed emulator is a buck converter with an average current mode control loop, which allows testing the static and dynamic performance of PV facilities up to 3 kW. To validate the concept, the emulator is used to evaluate the MPPT algorithm of a 230-W experimental microinverter working from a single PV module., This work is supported by the Spanish Ministry of Science and Innovation under grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Review of anti-islanding techniques in distributed generators

  • Velasco, D.
  • Trujillo, C. L.
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
[EN] In this paper a revision about different techniques for islanding detection in distributed generators is presented. On one hand, remote techniques, not integrated in the distributed generators, are discussed. On the other hand, local techniques, integrated in the distributed generator, are described. Furthermore, it is discussed how the local techniques are divided into passive techniques, based on exclusively monitoring some electrical parameters, and active techniques, which intentionally introduce disturbances at the output of the inverter, in order to determine if some parameters are affected., This work was supported by the Spanish Ministry of Science and Innovation under Grants ENE2006-15521-C03-02 and ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modeling and control of a push-pull converter for photovoltaic microinverters operating in island mode

  • Trujillo Rodríguez, César Leonardo
  • Velasco de la Fuente, David
  • Ortega, Rubén
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
[EN] This paper presents the modeling and control of a push-pull converter integrated into a two-stage photovoltaic microinverter operating in island mode without backup energy storage components (batteries). A push-pull small signal model is presented, from which they are derived all transfer functions needed to implement the controllers that regulate the output current, input voltage and output voltage interacting with the MPPT algorithm. A significant contribution of the paper is the proposal of an innovative control structure that simultaneously regulates in island mode both the ac voltage and the dc voltage of the panels, in order to place it in the best operation point. Such operation point is calculated by a specific control loop that interacts with the MPPT algorithm. To validate the proposed concept, simulations in PSIM (TM) were carried out. (C) 2011 Elsevier Ltd. All rights reserved., This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dynamic modeling of DC-DC converters with peak current control in double-stage photovoltaic grid-connected inverters

  • Garcerá, Gabriel|||0000-0002-5507-4379
  • González-Medina, Raúl|||0000-0003-0378-5045
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Sandia Paredes, Jesús|||0000-0002-4198-8364
In photovoltaic (PV) double-stage grid-connected inverters a high-frequency DC-DC isolation and voltage step-up stage is commonly used between the panel and the grid-connected inverter. This paper is focused on the modeling and control design of DC-DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. In the proposed overall control structure the output voltage of the DC-DC converter is regulated by the grid-connected inverter. Therefore, the inverter may be considered as a constant voltage load for the development of the small-signal model of the DC-DC converter, whereas the PV panel is considered as a negative resistance. The sensitivity of the control loops to variations of the power extracted from the PV panel and of its voltage is studied. The theoretical analysis is corroborated by frequency response measurements on a 230 W experimental inverter working from a single PV panel. The inverter is based on a Flyback DC-DC converter operating in discontinuous conduction mode (DCM) followed by a PWM full-bridge single-phase inverter. The time response of the whole system (DC-DC + inverter) is also shown to validate the concept. Copyright © 2011 John Wiley & Sons, Ltd. In photovoltaic (PV) double-stage gridconnected inverters a high-frequency DC-DC isolation and voltage step-up stage is commonly used between the panel and the grid-connected inverter. This paper is focused on the modeling and control design of DC-DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. The sensitivity of the control loops to variations of the power extracted from the PV panel and of its voltage is studied. Copyright © 2011 John Wiley & Sons, Ltd. Copyright © 2011 John Wiley & Sons, Ltd., This work was supported by the Spanish Ministry of Science and Innovation (MICINN) under grant ENE2009-13998-C02-02. The company AUSTRIAMICROSYSTEMS co-financed this project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Grid-tie inverter topology with maximum power extraction from two photovoltaic arrays

  • Patrao Herrero, Iván|||0000-0003-4412-0365
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • González-Medina, Raúl|||0000-0003-0378-5045
This study presents a transformerless topology for a grid-tied single-phase inverter capable of performing the simultaneous maximum power point tracking of two independent and series connected photovoltaic sources. This topology is derived from the neutral point clamped multilevel inverter in half-bridge configuration. The use of a half-bridge topology reduces the leakage current to very low values, whereas the multilevel topology presents an output voltage quality similar to that of a full-bridge inverter. To simultaneously track the maximum power of both photovoltaic sources, a generation control circuit is used. With this topology, it is possible to improve the performance of the converter under partial shadowing conditions, very common in photovoltaic facilities operating in residential areas. A 5 kW prototype of this topology has been implemented and tested in the laboratory., This work is supported by the Spanish Ministry of Science and Innovation under grants ENE2009-13998-C02-02 and ENE2012-37667-C02-01.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Reconfigurable control scheme for a PV microinverter working in both grid connected and island modes

  • Trujillo Rodríguez, Cesar Leonardo
  • Velasco de la Fuente, David
  • Garcerá, Gabriel
  • Guacaneme Moreno, Javier Antonio
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
In this paper, a photovoltaic (PV) microinverter capable of operating in both island mode and grid-connected mode by means of a reconfigurable control scheme is proposed. The main advantage of control reconfiguration is that in grid-connected mode, the microinverter works as a current source in phase with the grid voltage, injecting power to the grid. This is the operation mode of most commercial grid-connected PV microinverters. The idea is to provide those microinverters with the additional functionality of working in island mode without changing their control algorithms for grid-connected mode, which were developed and refined over time. It is proposed that in island mode, the microinverter control is reconfigured to work as a voltage source using droop schemes. These schemes consist in implementing P/Q strategies in the inverters, in order to properly share the power delivered to the loads. The aim of the paper is to show that the proposed control reconfiguration is possible without dangerous transients for the microinverter or the loads. Simulation and experimental results on an 180-W PV microinverter are provided to show the feasibility of the proposed control strategy., This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Transformerless topologies for grid-connected single-phase photovoltaic inverters

  • Patrao Herrero, Iván|||0000-0003-4412-0365
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • González Espín, Francisco José
[EN] In order to improve the efficiency and reduce the cost of a photovoltaic system, the use of transformerless photovoltaic inverters is an alternative of increasing interest. However, this topology needs to be studied in detail, as it presents some problems related to the galvanic connection between the grid and the photovoltaic generator (e.g. efficiency degradation and safety problems). In this paper, a review of grid-connected single-phase photovoltaic inverters based on transformerless topologies has been carried out. On the one hand, some alternatives based on classical topologies have been presented. On the other hand, alternatives based on multi-level inverter topologies have been studied, showing up that no leakage current is generated in comparison to classical topologies. © 2011 Elsevier Ltd All rights reserved., This work is supported by the Spanish Ministry of Science and Innovation under grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the control structure of wind energy generation systems based on a permanent magnet synchronous generator

  • Carranza Castillo, Oscar
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • González-Medina, Raúl|||0000-0003-0378-5045
This paper presents the analysis of the two usual control structures for variable speed and fixed pitch wind energy generation systems, namely speed and torque control, to determine the most appropriate structure to improve both robustness and reliability of this kind of distributed generators. The study considers all the elements of a typical wind power generation system and it has been carried out in a general way, so that conclusions are independent of the kind of the AC/DC converter that it is used to process the energy at the output of the generator. Particular emphasis was placed on developing a model of the turbine where the mechanical torque is considered as a system variable and not an exogenous disturbance for the system, as in other previous studies. After showing that speed control presents several advantages in terms of stability and reliability, an experimental study of this technique was carried out by using a grid connected wind generation system, which is composed by a three-phase boost rectifier feeding the grid connected inverter. Other practical issues for the design of high efficient wind generation systems, like the use of a Kalman speed estimator to avoid the need of mechanical sensors, are also implemented in the prototype and discussed in the paper. (c) 2012 Elsevier Ltd. All rights reserved., The first author thanks the support of the Instituto Politecnico Nacional (IPN) and of the Comision de Operacion y Fomento de Actividades Academicas (COFAA). This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of active islanding detection methods for grid-connected microinverters for renewable energy processing

  • Trujillo Rodríguez, Cesar Leonardo
  • Velasco de la Fuente, David
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
[EN] This paper presents the analysis and comparison of the main active techniques for islanding detection used in grid-connected microinverters for power processing of renewable energy sources. These techniques can be classified into two classes: techniques introducing positive feedback in the control of the inverter and techniques based on harmonics injection. Accurate PSIMTM simulations have been carried out in order to perform a comparative analysis of the techniques under study and to establish their advantages and disadvantages according to IEEE standards., This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparative study of speed estimators with highly noisymeasurement signals for Wind Energy Generation Systems

  • Carranza Castillo, Oscar
  • González Morales, Luis Gerardo
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
This paper presents a comparative study of several speed estimators to implement a sensorless speed control loop in Wind Energy Generation Systems driven by power factor correction three-phase boost rectifiers. This rectifier topology reduces the low frequency harmonics contents of the generator currents and, consequently, the generator power factor approaches unity whereas undesired vibrations of the mechanical system decrease. For implementation of the speed estimators, the compared techniques start from the measurement of electrical variables like currents and voltages, which contain low frequency harmonics of the fundamental frequency of the wind generator, as well as switching frequency components due to the boost rectifier. In this noisy environment it has been analyzed the performance of the following estimation techniques: Synchronous Reference Frame Phase Locked Loop, speed reconstruction by measuring the dc current and voltage of the rectifier and speed estimation by means of both an Extended Kalman Filter and a Linear Kalman Filter. © 2010 Elsevier Ltd., The first author thanks the support of the Instituto Politecnico Nacional (IPN) to finance his stay at the Universidad Politecnica de Valencia (UPV). This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Control techniques for reduction of the total harmonic distortion in voltage applied to a single-phase inverter with nonlinear loads: Review

  • Ortega, Rubén
  • Trujillo Rodríguez, César Leonardo
  • Velasco de la Fuente, David
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
  • Garcerá, Gabriel|||0000-0002-5507-4379
[EN] This paper presents the design, analysis and implementation of four control techniques (proportional-integral, two-degree of freedom, repetitive and resonant) with the aim of reducing the total harmonic distortion in voltage (THDv). When the inverter is working as a voltage source theses techniques are useful in island mode operation. The purpose is to keep the output voltage waveform, frequency and amplitude according to the standard IEEE 519, when nonlinear loads are fed. A comparative analysis derived from inverter simulations with nonlinear loads is realized in order to validate those control techniques. (C) 2011 Elsevier Ltd. All rights reserved., This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02. The first author thanks the support of the Instituto Politecnico Nacional (IPN), the Comision de Operacion y Fomento de Actividades Academicas (COFAA), the Secretaria de Educacion Publica and the Agencia Espanola de Cooperacion Internacional para el Desarrollo (AECID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An Adaptive Control System for Three-Phase Photovoltaic Inverters Working in a Polluted andVariable Frequency Electric Grid

  • González Espín, Francisco José
  • Garcerá, Gabriel|||0000-0002-5507-4379
  • Patrao Herrero, Iván|||0000-0003-4412-0365
  • Figueres Amorós, Emilio|||0000-0002-0716-3916
Theproportional+resonant (PR) controller has been proposed in the past as a suitable method to control the current generated by the grid-connected photovoltaic voltage source inverters. Due to the fact that information regarding the frequency of the grid is needed to use this control technique, the synchronous reference frame phase-locked loop (SRF-PLL) is commonly used. To assure that the total harmonic distortion of the injected current (THDi) meets the appropriate standards, even if the grid voltage is polluted and its frequency varies, an adaptive control strategy is presented in this paper. This control strategy can improve the behavior of both, the conventional SRF-PLL and the conventional PR controller, when they are used in a polluted grid with a time varying frequency. The experimental results obtained by means of a digitally controlled 10-kVA inverter, show up that the THDi of the injected current is improved when the proposed adaptive control strategy replaces the conventional one., This work was supported by the Spanish Ministry of Science and Innovation under Grant ENE2009-13998-C02-02. Recommended for publication by Associate Editor B. Lehman.