Pasar al contenido principal

DISEÑO Y FABRICACION DE UNA PILA PEM ULTRALIGERA DE MEDIANA POTENCIA PARA UNIDAD DE ENERGIA DE UN UAV

ENE2012-38642-C02-01

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Use of fuel cell stacks to achieve high altitudes in light unmanned aerial vehicles

  • Renau, Jordi
  • Lozano, Antonio
  • Barroso Estébanez, Jorge Angel
  • Miralles, José
  • Martín, Jesús
  • Sánchez, Fernando
  • Barreras, Félix
A study is presented to determine if substituting an internal combustion engine (ICE) by an electric motor powered by a fuel cell stack can be a viable option to increase the service ceiling of an available light unmanned aerial vehicle (UAV), extending it to 10,000 m. As a first condition, the stack has to be capable of supplying the minimum power required for horizontal leveled flight at this altitude, which is a function of the UAV total mass. A second step examines if the UAV can transport the energy required to reach the desired service ceiling without exceeding the maximum mass that can be loaded, considering that both hydrogen and oxygen have to be carried on-board. A particularly light PEM fuel cell stack is proposed as a suitable power source. A realistic system is described to store the required amount of reactant gases maintaining the mass below the allowable limits. Results indicate that with its aerodynamic characteristics, the UAV should be capable of ascending up to 10,000 m with the described fuel cell and gas storage system. Some multivariable maps that include service ceiling, total payload and required power are provided to perform this type of analysis.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Analysis of the performance of a passive hybrid powerplant to power a lightweight unmanned aerial vehicle for a high altitude mission

  • Renau, Jordi
  • Sánchez, Fernando
  • Lozano, Antonio
  • Barroso, Jorge
  • Barreras, Félix
The objective of this research is to analyze the performance of a passive hybrid powerplant control system to be implemented in a lightweight unmanned aerial vehicle capable to ascend up to the high troposphere (10, 000 m). The powerplant is based on a high-temperature PEM fuel cell connected in parallel to a set of lithium-polymer batteries and regulated by two power diodes. Test performed in steady state demonstrates that the use of the hybrid system increases the efficiency of the stack by more than 7% because the voltage at the main DC bus is limited by the batteries. The robustness of the passive control system is proved in a long-term test in which random perturbations of ±15% are applied to the average power that would be demanded during the ascent flight. The hybridization of the stack with the batteries eliminates sudden peaks in the current generated by the stack, which are responsible for prompt degradation phenomena that drastically reduce its useful lifetime. The study demonstrates that with the passive hybrid powerplant it is possible to reach the target height with the gas storage system considered in the application, contrary to what happens with the simple power plant.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Design and manufacture of a high-temperature PEMFC and its cooling system to power a lightweight UAV for a high altitude mission

  • Renau, J.
  • Barroso, J.
  • Lozano, A.
  • Nueno, A.
  • Sánchez, F.
  • Martín, J.
  • Barreras, F.
In the present study, the optimal design of a high-temperature proton exchange membrane fuel cell (HT-PEMFC) that will be used to power an unmanned aerial vehicle (UAV) in a high altitude mission is performed. The use of PEMFCs for service ceiling above 10 km implies overcoming a number of problems caused by the harsh environmental conditions. Among them, new strategies to manage the heat generated by electrochemical reactions are needed. The maximum power required by the UAV was determined solving the aerodynamic problem, and the design of the lightweight HT-PEMFC, including its cooling system, was optimized. To perform the numerical solution of the heat transfer problem, a computational code was implemented using the EES software. The decisions adopted resulted in a 40-cells stack with an electric power above 1 kW and a weight around 3.65 kg. Besides, it is demonstrated that, for the configuration considered in the study, a passive cooling system without any additional fan system can be used to maintain the stack temperature in 160 °C.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Experimental determination of the heat transfer coefficient for the optimal design of the cooling system of a PEM fuel cell placed inside the fuselage of an UAV

  • Barroso, Jorge
  • Jordi Renau, Jordi
  • Lozano, Antonio
  • Miralles, José
  • Martín, Jesús
  • Sánchez, Fernando
  • Barreras, Félix
The objective of this research is to calculate the heat transfer coefficients needed for the further design of the optimal cooling system of a high-temperature polymer electrolyte membrane fuel cell (HT-PEMFC) stack that will be incorporated to the powerplant of a light unmanned aerial vehicle (UAV) capable of reaching an altitude of 10,000 m. Experiments are performed in two rectangular tunnels, for three different form factors, in experimental conditions as close as possible to the actual ones in the HT-PEMFC stack. For the calculations, all the relevant thermal processes are considered (i.e., convection and radiation). Different parameters are measured, such as air mass flow rate, inlet and outlet air temperatures, and wall temperatures for bipolar plates and endplates. Different numerical models are fitted revealing the influence of the diverse relevant non-dimensional groups on the Nusselt number. Heat transfer coefficients calculated for the air cooling flow vary from 8 to 44 W m2 K1. Results obtained at sea level are extrapolated for a flight ceiling of 10 km. The flow section is optimized as a function of the power required to cool the stack down to the temperature recommended by the membrane-electrode assembly (MEA) manufacturer using a numerical code specifically developed for this purpose.