Pasar al contenido principal

MEJORA DE LA CONVERSION DE ENERGIA SOLAR MEDIANTE PROCESOS DE EXCITACION ELECTRONICA EN DOS ETAPAS. APROXIMACION ELECTROQUIMICA.

ENE2013-46624-C4-4-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Zinc Content in Ternary ZnCdS Films Deposited by Chemical Bath Deposition for Photovoltaic Applications

  • Ullah, Shafi
  • Ullah, Hanif
  • Bouhjar, F.
  • Chahboun, Adil
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Cadmium Zinc Sulfide thin films with different Zn concentration were synthesized in aqueous solution by chemical bath deposition (CBD) method using CdSO4, ZnSO4, CH4N2S for Cd+2, Zn+2, and S¿2 ions source, respectively. The as-deposited films are well homogeneous, adherent and free from pinholes. The incorporation of Zn in CdS was found to be dependent on the annealing temperature. Structure, morphology, elemental analysis, optical and photoelectrochemical (PEC) properties of ZnCdS were characterized using X-ray diffraction, atomic force microscopy, energy dispersive spectroscopy, transmission electron microscopy and UV-Vis absorption measurements, respectively. According to EDS analysis the films are non-stoichiometric due to a deficit of sulfur, which becomes more important as the Zn content increases. The absorption edge shifts toward the lower wavelength region and hence the bandgap of the films increases as the Zn content increases. The values of optical absorption edge are found to change from 2.42 eV for CdS and 2.90 eV for ZnS thin films. The PEC and linear sweep voltammetry performance of the Zn doped CdS films were examined by chronoamperometry technique which provided a significant high potential current due to increase of the electrical conductivity as compared to CdS film., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044). The Universitat Politecnica de Valencia, Coordinator of the Erasmus + KA 107 Scholarship funded by European Union under project (2016-17)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thin Film of Perovskite (Mixed-Cation of Lead Bromide FA(1-x)MA(x)PbBr) Obtained by One-Step Method

  • Slimi, B.
  • Chtourou, R.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Perovskite materials for solar cell applications were prepared by a one-step method. In the following work, the spin coating technique was used for organic-inorganic hybrid perovskite formamidinium lead tribromide (FAPbBr(3)), methylammonium lead tribromide (MAPbBr(3)) and formamidinium methylammonium lead tribromide (FA(1-x)MA(x)PbBr(3)).Thin films of mixed FA(1-x)MA(x)PbBr(3) (x = 0-1) perovskites deposited on indium tin oxide glass substrates were obtained by mixing FAPbBr(3) and MAPbBr(3) in different proportions. Structural x-ray diffraction (XRD), morphological (Scanning Electron Microscopy (SEM) and energy dispersive x-ray spectroscopy (EDX) and optical (uv-visible spectroscopy (UV-Vis) proprieties were investigated for all synthesized perovskites as a function of the MA/FA ratio. The (XRD) analysis shows the formation of a cubic-phase perovskite with space group Pm-3 m in the composition range 0 <= x <= 1. High absorbance levels were obtained in the infrared region 500-900 nm for mixed perovskites FAMAPbBr(3). The estimated energy band-gap from the absorbance spectral measurements for FAMAPbBr(3) thin films was in the range of 2.2 eV for FAPbBr(3) and 2.3 eV for MAPbBr(3), respectively. The photoluminescence emission of mixed FA/MA perovskite thin films was located in intermediate values between 580 nm and 555 nm., Nanomaterials and Systems Laboratory for Renewable Energies, Research and Technology Center of Energy Technoparc Borj Cedria for financial support. This work was supported by the Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and the Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of iodide substitution on the physical properties and stability of cesium lead halide perovskite thin films CsPbBr3-xIx (0 &lt, = x &lt, = 1)

  • Atourki, Lahoucine
  • Vega-Fleitas, Erica
  • Kirou, Hassan
  • Bouabid, Khalid
  • Ihlal, Ahmed
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] This study sheds light on the effect of iodide substitution on the structural and optical properties of solution processed mixed cesium lead perovskite thin films CsPbBr3-xIx (0 <= x <= 1) as well as their atmospheric and thermal stability. Pawley fit indicated that the mixed lead halide CsPbBr(3-x)l(x) perovskite crystallizes in the orthorhombic (Pnma) space group. X-ray diffraction analyses showed a shift to lower angles when the average fraction of iodide incorporated increased indicating the expansion of the lattice. Absorbance measurements show that the CsPbBr3-xIx films exhibit a very high absorbance in the visible and short infrared region. The band gap of CsPbBr(3-x)l(x) is tuned from 238 (CsPbBr3) to 2.17 eV (CsPbBr2I1) following the Vegard's law. CsPbBr3 films showed a bright photoluminescence with emission maximum at 530 nm CsPbBr(3-x)l(x) films demonstrate excellent stability after aging for two days in a humid environment (relative humidity of 60%) and under thermal annealing at relatively high temperature. (C) 2017 Elsevier B.V. All rights reserved., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

MAPbI2.9-xBrxCl0.1 hybrid halide perovskites: Shedding light on the effect of chloride and bromide ions on structural and photoluminescence properties

  • Atourki, L.
  • Vega-Fleitas, Erica
  • Ahsaine, H.A.
  • Bouabid, K.
  • Ihlal, A.
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
[EN] The optical and structural properties of CH3NH3PbI3 can be adjusted by introducing other extrinsic ions such as chloride and bromide. In this work, mixed bromide iodide lead perovskites with a 10% fraction of chloride were prepared from methylamine, lead nitrate and the corresponding hydro acid (X = I, Br, Cl). The effect of bromide and chloride incorporation on different properties of perovskite thin film was investigated. The Pawley fit method indicates the formation of the iodide halide MAPbI3 Pm-3 m cubic phase for x = 0 and the tetragonal P4/mmm phase for x &#8805; 0.3. All deposited films showed a strong absorbance in the UV vis range. The band gap values were estimated from absorbance measurements. It was found that the onset of the absorption edge for MAPbI2.9-xBrxCl0.1 thin film perovskites ranges between 1.60 and 1.80 eV. Moreover, it was found that both Cl and Br affect the PL emission of the mixed halide lead perovskite, the MAPbI2.9&#8722;xBrxCl0.1 films displayed intermediate values from 730 nm (MAPbI2.2Br0.7Cl0.1) to 770 nm (MAPbI2.6Br0.3Cl0.1), This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical synthesis of hexagonal hollow ZnO nanostructures

  • Abellan Rubio, Mª Angeles
  • Moya Forero, Mónica Mercedes
  • Marí, B.|||0000-0003-0001-419X
[EN] A simple and controllable one-step electrodeposition process is proposed in order to obtain ZnO nanotubes. Zinc oxide thin films were grown on fluorine-doped tin oxide by electrodeposition from an aqueous electrolyte containing zinc nitrate and potassium nitrate. Generally, in aqueous electrolytes ZnO is electrochemically deposited in the form of hexagonal nanocolumns. These nanocolumns grow perpendicularly to the substrate until reaching a maximum height of about 2 µm and then the perpendicular growth vanishes and the solid nanocolumns develop to hexagonal hollow structures. Several characteristics of the electrodeposited films such as thickness, morphology and crystalline structure were obtained as a function of the deposited charge. The evolution of the morphology of the electrodeposited layers as a function of time was monitored by Scanning Electron Microscopy. X-Ray Diffraction confirms that hexagonal nanotubes are preferentially oriented along the (002) direction., This work was supported by CONICYT (project 3130451), Ministerio de Economía y Competitividad (project ENE2013-46624-C4-4-R) and European Commission through NanoCISproject FP7-PEOPLE-2010-IRSES (ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Perovskite FA1-xMAxPbI3 for solar cells: films formation and properties

  • Slimi, B.
  • Ben Assaker, I.
  • Kriaa, A.
  • Chtourou, R.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Organic-inorganic hybrid perovskite formamidinium lead triiodide NH2CHNH2PbI3 (FAPbI3), methylammonium lead triiodide CH3NH3PbI3 (MAPbI3) and formamidinium methylammonium lead triiodide (NH2CHNH2)1-x(CH3NH2)xPbI3 (FA1-xMAxPbI3) thin films were synthesized and deposited on indium tin oxide glass substrates by spin coating process. Thin films of mixed FA1-xMAxPbI3 (x = 0-1) perovskites obtained by mixing FAPbI3 and MAPbI3 in different proportions. The morphological, structural and optical proprieties of all synthetized perovskites have been analyzed as a function of the MA/FA ratio. X-ray diffraction analyses indicated the formation a cubic perovskite phase with space group Pm-3m in the composition range 0 ¿ x ¿ 1. Mixed perovskites FAMAPbI3 showed a high absorbance in the infrared region 780-900 nm. The band gap energy estimated from absorbance spectral measurements for FAMAPbI3 thin films ranges from 1.50 eV for FAPbI3 to 1.56 eV for MAPbI3, respectively. The overall PL emissions of mixed FA/MA perovskite thin films are located in intermediate values between 773 nm and 810 nm., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synthesis of MAPbBr3-iYi (Y=I, Cl, i=0 ,1 ,2, 3) perovskite thin films

  • Vega-Fleitas, Erica
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Methylammonium lead halide perovskites with different halides (iodide, bromide and chloride) have been synthetized from methylamine, lead nitrate and the corresponding hydroX acid (X = I, Br, Cl) precursors. Subsequently MAPbBr3-iYi (Y= I, Cl; i=0, 1, 2, 3) perovskites were deposited as thin films onto FTO substrates by spin coating or dipping. Thin film perovskites were then characterized by X-Ray Diffraction, elemental analysis and optical spectrometry. Crystallites sizes are between 100-600 nm depending on the synthesis temperature. All synthetized MAPbX3-iYi perovskites crystallized in the same cubic phase irrespective of the X and Y components and a unique phase is observed. Elemental analy- sis shows that in all cases the atomic components meet the expected stoichiometric formulae. The bandgap of thin film MAPbX3-iYi perovskites were inferred from transmittance and reflectance spectral measurements. It is found that the on-set of the absorption edge for thin film MAPbX3 perovskites is about 1.66, 2.55 and 3.37 eV for X= I, Br, Cl, respectively "and it reaches intermediate values for mixed MAPbX3-iYi perovskites., This work was supported by Ministerio de Economía y Competitividad (ENE2013-46624-C4-4-R)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Photoluminescent properties of electrochemically synthetized ZnO nanotubes

  • Gracia Jimenez, J. M.
  • Cembrero Cil, Jesús
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
ZnO nanotubes were prepared by a sequential combination of electrochemical deposition, chemical attack and regeneration. ZnO nanocolumns were initially electrodeposited on conductive substrates and then converted into nanotubes by a process involving chemical etching and subsequent regrowth. The morphology of these ZnO nanocolumns and derived nanotubes was monitored by Scanning Electron Microscopy and their optical properties was studied by photoluminescence spectroscopy. Photoluminescence were measured as a function of temperature, from 6 to 300 K, for both nanocolumns and nanotubes. In order to study the behaviour of induced intrinsic defect all ZnO films were annealed in air at 400 °C and their photoluminescent properties were also registered before and after annealing. The behaviour of photoluminescence is explained taking into account the contribution of different point defects. A band energy diagram related to intrinsic defects was proposed to describe the behaviour of photoluminescence spectra, This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrodeposition of CuGaSe2 and CuGaS2 thin films for photovoltaic applications

  • Ullah, Shafi
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
Abstract CuGaSe2 and CuGaS2 polycrystalline thin film absorbers were prepared by one-step electrodeposition from an aqueous electrolyte containing CuCl2, GaCl3 and H2SeO3. The pH of the solution was adjusted to 2.3 by adding HCl and KOH. Annealing improved crystallinity of CuGaSe2 and further annealing in sulphur atmosphere was required to obtain CuGaS2 layers. The morphology, topography, chemical composition and crystal structure of the deposited thin films were analysed by scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy and X-ray diffraction, respectively. X-Ray diffraction showed that the asdeposited CuGaSe2 film exhibited poor crystallinity, but which improved dramatically when the layers were annealed in forming gas atmosphere for 40 min. Subsequent sulphurization of CuGaSe2 films was performed at 400 °C for 10 min in presence of molecular sulphur and under forming gas atmosphere. The effect of sulphurization was the conversion of CuGaSe2 into CuGaS2. The formation of CuGaS2 thin films was evidenced by the shift observed in the X-ray diffraction pattern and by the blue shift of the optical bandgap. The bandgap of CuGaSe2 was found to be 1.66 eV, while for CuGaS2 it raised up to 2.2 eV. A broad intermediate absorption band associated to Cr and centred at 1.63 eV was observed in Cr-doped CuGaS2 films., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044). One of the authors (S. Ullah) acknowledges the European Union (IDEAS-Call-3, Innovation and Design for Euro-Asian scholars) for its financial support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Role of the chemical substitution on the structural and luminescence properties of the mixed halide perovskite thin MAPbI3-xBrx (0:1) films

  • Atourki, L.
  • Vega-Fleitas, Erica
  • Hassan Ait Ahsaine
  • Bouabid, Khalid
  • Ihlal, Ahmed
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
Mixed bromide iodide lead perovskites were prepared from methylamine, lead nitrate and the corre- sponding hydroX acid (X = I, Br), they were then deposited as thin films on ITO substrate by the spin coating process. X-ray diffraction analyses indicated the formation of a tetragonal phase I4/mcm up to x = 0.4 and a cubic perovskite with space group Pm3 m in the composition range of 0.6-1. Mixed lead perovskites showed a high absorbance in the UV vis range. The band gap energy of thin films were estimated from absorbance spectral measurements, it was found that the onset of the absorption edge for MAPbI3- x Brx (x < 1) thin films is ranging between 1.58 to 1.72 eV. Photoluminescence emission energies for mixed halide perovskites presented intermediate values from 781 nm (MAPbI3 ) to 545 nm (MAPbBr3 )., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

One step electrodeposition of Ag-decorated ZnO nanowires

  • Slimi, B.
  • Ben Assaker, I.
  • Kriaa, A.
  • Chtourou, R.
  • Marí, B.|||0000-0003-0001-419X
A new route for synthesizing Ag-decorated ZnO nanowires (NWs) on conductive glass substrates using a one-step electrodeposition technique is described here. The structural, optical, and photoelectrochemical properties of Ag-decorated ZnO nanowires were studied in detail using techniques such X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, UV-visible spectroscopy, photoluminescence, and photoelectrochemical measurements. Both pure and Ag-decorated ZnO nanowires were found to crystallize in the wurtzite structure, irrespective of their Ag contents. Increasing the Ag content from pure ZnO NWs to 3% Ag ZnO NWs decreases the photoluminescence intensity, shifts the optical band gap to the red, and increases the photocurrent up to threefold. This behavior was attributed to the surface plasmon resonance effect induced by the Ag nanoparticles, which inhibits charge recombination and improves charge transport on the ZnO surface., B.S. acknowledges the Nanomaterials and Systems Laboratory for Renewable Energies, Research and Technology Centre of Energy Technoparc Borj Cedria for financial support. This work was supported by the Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and the Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Substrate Influences on the Properties of SnS Thin Films Deposited by Chemical Spray Pyrolysis Technique for Photovoltaic Applications

  • Sall, Thierno
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
Herein, we report on tin monosulfide (SnS) thin films elaborated by the Chemical Spray Pyrolysis (CSP) technique onto various substrates as simple glass, ITO-, and Mo-coated glasses in order to study the influence of substrates on the physical and chemical properties of Sns thin films. Structural analysis revealed that all films crystallize in orthorhombic structure with (111) as the sole preferential direction without secondary phases. In addition, film prepared onto pure glass exhibits a better crystallization compared to films deposited onto coated glass substrates. Raman spectroscopy analysis confirms the results obtained by X-ray diffraction with modes corresponding well to SnS single crystal orthorhombic ones (47, 65, 94, 160, 186, and 219 cm21) without any additional parasite secondary phase like Sn2S3 or SnS2. Field emission scanning electron microscope revealed that all films have a cornflake-like particles surface morphology, and energy dispersive X-ray spectroscopy analysis showed the presence of sulfur and tin with a nearly stoichiometric ratio in films deposited onto pure glass. High surface roughness and large grains are observable in film deposited onto glass. From optical spectroscopy, it is inferred that band gap energy of SnS/glass and SnS/ITO were 1.64 and 1.82 eV, respectively., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optical properties of Yb3+ doped ZnO/MgO nanocomposites

  • Marí, B.|||0000-0003-0001-419X
  • Jindal, J.
  • Singh, Krishan Chander
  • Verma, Naveen
[EN] Yb3þ doped ZnO/MgO nanocomposite were prepared by combustion synthesis method. The samples were further heated to 1000 °C to improve their crystallinity and photoluminescent efficiency. The concentrations of Yb3þ and Mg2þ were varied between 1–2% and 5–70% respectively in prepared samples. The nano-powders were characterized by Scanning Electron Microscopy and X-ray Diffraction for morphology and structural determination. XRD studies have revealed the wurtzite structure for MgxZn1"xO for Mg concentrations below 30%. Higher concentrations of Mg results in Yb3þ doped ZnO/ MgO nanocomposite containing three phases; the wurzite hexagonal phase typical of ZnO, the cubic phase of MgO and a small amount of cubic Yb2O3 phase. As expected, the amount of cubic phase in nanopowders increased with the increase of Mg concentration in ZnO. The crystallite size of ZnO/MgO composites decreased from 55 nm to 30 nm with increase of Mg content. SEM images of Yb3þ doped ZnO/MgO nanocomposite with higher Mg content (450%) showed clearly distinct hexagonal and cubical shaped nano-particles. Photoluminescent emission showed a broad band in the range (435 nm to 700 nm). Pure ZnO nano-phosphor showed an emission peak around 545 nm, which is blue shifted with Mg content. The photoluminescence intensity increased with increase of Mg content in ZnO and it became maximum with 30% Mg concentration. Time resolved decay curves of photoluminescence indicated decay time in microsecond time scale, This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R), Generalitat Valenciana (PROMETEUS-II/2014/044) and the European Commission through NanoCIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparative study on MAPbI3 based solar cells using different electron transporting materials

  • Adhikari, Krishna R.
  • Gurung, S.
  • Bhattarai, Binod
  • Marí, B.|||0000-0003-0001-419X
[EN] This paper presents a comparative study on organometal halide perovskite based solar cells using two different transparent conducting oxides such as TiO2 and ZnO as electron transporting materials. Simulation is an interesting tool for studying the behavior of every component of a solar cell device as well as for analyzing the performance of the full device. Solar cell capacitance simulator (SCAPS)-1D has been the tool used for numerical simulation of such devices. Influences of thickness of absorber and ETMs, interface trap density of states and dopant concentration of ETMs on the performance of photovoltaic solar cells are studied. Comparable efficiencies of 22.35% and 22.49% for PV devices made of spiro-MeOTAD/MAPbI3/TiO2 and spiroMeOTAD/MAPbI3/ZnO, respectively, with 400/400/90 nm thicknesses under 1 Sun illumination are observed. The performance of both devices indicates the replacement of the TiO2 by a ZnO layer. It could be a good option to reduce the cost and increase the mobility of ETM for this type of solar cells. Generally, increase in thickness of MAPbI3 perovskite up to around 700 nm results into increase in the power conversion efficiency (PCE) of the solar cells. On the other hand, TiO2 and ZnO layers thicker than 90 nm results into decrease in the efficiency of the devices. Furthermore, the increase in interface trap density is found to reduce the efficiency of the devices., This work was supported by Ministerio de Economía y Competitividad through grant ENE2013- 46624-C4-4-R. One of the authors (Krishna Raj Adhikari) acknowledges the University Grants Commission, Nepal and Erasmus Mundus IDEAS, European Commission for their scholarship and Mobility Action-2 Program. The authors are also very grateful to Dr. Marc Bergelman from University of Gent for providing SCAPS simulation program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of a Compact Fe2O3 Layer on the Photovoltaic Performance of Perovskite-Based Solar Cells

  • Bouhjar, F.
  • Ullah, Shafi
  • Bessais, B.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] In this study, uniform and dense iron oxide ¿-Fe2O3 thin films were used as an electron-transport layer (ETL) in CH3NH3PbI3-based perovskite solar cells (PSCs), replacing the Titanium dioxide (TiO2) ETL conventionally used in planar heterojunction perovskite solar cells. The ¿-Fe2O3 films were synthesized using an electrodeposition method for the blocking layer and a hydrothermal method for the overlaying layer, while 2,2¿,7,7¿-tetrakis (N, N¿-di-p-methoxyphenylamine)-9,9¿ spirobifluorene (spiro-OMeTAD) was employed as a hole conductor in the solar cells. Based on the above synthesized ¿-Fe2O3 films the photovoltaic performance of the PSCs was studied. The ¿-Fe2O3 layers were found to have a significant impact on the photovoltaic conversion efficiency (PCE) of the PSCs. This was attributed to an efficient charge separation and transport due to a better coverage of the perovskite on the ¿-Fe2O3 films. As a result, the PCE measured under standard solar conditions (AM 1.5G, 100 mW cm¿2) reached 5.7%., This work was supported by the Ministry of High Education and Scientific Research, Tunisia and Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitatvalenciana (Prometeus 2014/044).