Pasar al contenido principal

MILICONCENTRADORES DIELECTRICOS MULTIFASE PARA INTEGRACION ARQUITECTONICA EN FACHADA DE SISTEMAS SOLARES HIBRIDOS

ENE2013-48325-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD DE LLEIDA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 31
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Energetic simulation of a dielectric photovoltaic-thermal concentrator

  • Moreno Bellostes, Àlex
  • Riverola Lacasta, Alberto
  • Chemisana Villegas, Daniel
A solar concentrating photovoltaic-thermal (CPVT) module with cell immersion in dielectric liquid has been modelled and energetically simulated. The concentrator focuses radiation linearly by using a cylindrical shape optics made of polymethyl methacrylate. The geometric concentration is 12 suns with an optical efficiency of 76.14%. The dielectric fluid, deionized water, flows through the concentrator case fulfilling a double function: to concentrate and to cool the PV cells. The concentrator is designed to be superimposed in front of the windows in a 2-storey family house with 4-person occupancy. The system is modelled to partially cover thermal and electrical demands utilizing a radiant floor and a reversible air-air heat pump for space heating and cooling (SH&C) and an electrical circuit which combines direct consumption and battery storage. The system topology has been simulated for three locations (Lisbon, Barcelona and Genoa). Results indicate an appropriate performance of the system analyzed with DHW solar fractions in a range from around 61% to above 75%. The lowest corresponds to Genoa and the highest to Lisbon and Barcelona. Regarding SH&C solar fractions are also quite adequate with values ranging from 38.3% (Genoa) to above 60% (68.8% in Lisbon and 62.4% in Barcelona). Finally, SFs for electrical loads take a value of 44.09% in the case of Lisbon, 38.9% for Barcelona and 23.51% for Genoa., The authors would like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant references ENE2013-48325-R, ENE2016-81040-R and BES-2014-069596) and “Generalitat de Catalunya” for the grant 2017FI_B_01171.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Environmental assessment of a pork-production system in North-East of Spain focusing on life-cycle swine nutrition

  • Lamnatou, Chrysovalantou
  • Ezcurra Ciaurriz, F. Xavier
  • Chemisana Villegas, Daniel
  • Pla Aragonés, Lluís Miquel
Given the importance of pig-meat production in Spain, the present work (based on cumulative energy demand, global warming potential, ReCiPe method and different functional units) presents a life cycle assessment of an intensive pork-production system (growing-finishing pigs from 25 to 105 kg body weight) in North-East of Spain. Emphasis is given on animal feeding (which is separated into 3 phases) while the impact of drinking-water consumption, straw usage and transportation (for feed and straw) are also taken into account for certain scenarios. The results demonstrate that there is a cumulative energy demand of 5.6 MJprim per kg of animal feed and 14.5-35.6 MJprim per kg of meat (live or carcass weight). Moreover, global warming potential (based on a time horizon of 100 years: 100a) is 3.2-5.5 kg CO2.eq per kg of meat (live or carcass weight) and 336-460 kg CO2.eq per market pig. On the other hand, ReCiPe impact per market pig ranges from 60 to 76 Pts, depending on the scenario. Based on all the studied cases, animal feed is responsible for the greatest part of the total impact feed/drinking-water/straw/transportation and transportation is responsible for the second highest impact. A comparison with results from the literature is also provided and critical issues (about feed composition, cleaner-production solutions, etc.) are presented., The authors would like to thank ''Ministerio de Economía y Competitividad'' of Spain for the funding (grant reference ENE2013-48325-R). Lluis M. Plà-Aragonés wishes to acknowledge the financial support of the Spanish Research ProgramTRA2013-48180-C3-P and CYTED program support to the thematic network P515RT0123.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Full modeling and experimental validation of cylindrical holographic lenses recorded in Bayfol HX photopolymer and partly operating in the transition regime for solar concentration

  • Marín Sáez, Julia
  • Atencia Carrizo, Jesús
  • Chemisana Villegas, Daniel
  • Collados, María Victoria
Concentrating photovoltaics for building integration can be successfully carried out with Holographic Optical Elements (HOEs) because of their behavior analogous to refractive optical elements and their tuning ability to the spectral range that the photovoltaic (PV) cell is sensitive to. That way, concentration of spectral ranges that would cause overheating of the cell is avoided. Volume HOEs are usually chosen because they provide high efficiencies. However, their chromatic selectivity is also very high, and only a small part of the desired spectral range reaches the PV cell. A novel approach is theoretically and experimentally explored to overcome this problem: the use of HOEs operating in the transition regime, which yield lower chromatic selectivity while keeping rather high efficiencies. A model that considers the recording material’s response, by determining the index modulation reached for each spatial frequency and exposure dosage, has been developed. It has been validated with experimental measurements of three cylindrical holographic lenses with different spatial frequency ranges recorded in Bayfol HX photopolymer. Simulations of systems comprising two lenses and a mono-c Si PV cell are carried out with the standard AM 1.5D solar spectrum. Promising results are obtained when using the system with lower spatial frequencies lenses: a total current intensity equal to 3.72 times the one that would be reached without the concentrator., Generalitat de Catalunya (2017FI_B2_00127); Ministerio de Economía y Competitividad of Spain (ENE2013-48325-R, ENE2016-81040-R); Diputación General de Aragón - Fondo Social Europeo (TOL research group, T76); Universidad de Zaragoza (UZ2017-CIE-02).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Characterization of volume holographic optical elements recorded in Bayfol HX photopolymer for solar photovoltaic applications

  • Marín Sáez, Julia
  • Atencia Carrizo, Jesús
  • Chemisana Villegas, Daniel
  • Collados, María Victoria
Volume Holographic Optical Elements (HOEs) present interesting characteristics for photovoltaic applications as they can select spectrum for concentrating the target bandwidth and avoiding non-desired wavelengths, which can cause the decrease of the performance on the cell, for instance by overheating it. Volume HOEs have been recorded on Bayfol HX photopolymer to test the suitability of this material for solar concentrating photovoltaic systems. The HOEs were recorded at 532 nm and provided a dynamic range, reaching close to 100% efficiency at 800 nm. The diffracted spectrum had a FWHM of 230 nm when illuminating at Bragg angle. These characteristics prove HOEs recorded on Bayfol HX photopolymer are suitable for concentrating solar light onto photovoltaic cells sensitive to that wavelength range., This research has been supported by the Spanish Ministerio de Economía y Competitividad (grants ENE2013-48325-R and FIS2012-35433), the Diputación General de Aragón-Fondo Social Europeo (TOL research group, T76) and the Generalitat de Catalunya (grant 2015 FI_B 00328).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Photovoltaic/thermal (PVT) systems: A review with emphasis on environmental issues

  • Lamnatou, Chrysovalantou
  • Chemisana Villegas, Daniel
The present article is a review about PVT (photovoltaic/thermal) investigations with emphasis on studies which include environmental issues about PVT technology. The references analyzed are presented according to certain criteria (e.g. the type of the system: BA (building-added), BI (building-integrated), CPVT (concentrating PVT), etc.). The literature review shows that most of the investigations examine EPBT (energy payback time) and CO2 emissions. In terms of the types of the systems, most of the studies are about BA PVT/water installations for domestic applications and thereby, more studies (which include environmental issues) are needed e.g. about BIPVT, CPVT, BICPVT and PVT systems for different applications (apart from the building sector), for example industrial. In addition, a separate section with factors which influence PVT from environmental point of view (PV cell material, heat transfer fluid, concentrators, alternative materials, etc.) is included. A critical discussion about these factors is also provided, explaining how they influence the environmental profile of a PVT system. Moreover, explanations about different methods and indicators which provide (or which can provide as a future prospect) useful information for PVT (from environmental point of view) are also presented., The authors would like to acknowledge networking support by the COST Action TU1205 Building Integration of Solar Thermal Systems. The authors would also like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant reference ENE2013-48325-R).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Energy simulation of a holographic PVT concentrating system for building integration applications

  • Marín Sáez, Julia
  • Chemisana Villegas, Daniel
  • Moreno Bellostes, Àlex
  • Riverola Lacasta, Alberto
  • Atencia Carrizo, Jesús
  • Collados, María Victoria
A building integrated holographic concentrating photovoltaic-thermal system has been optically and energetically simulated. The system has been designed to be superimposed into a solar shading louvre; in this way the concentrating unit takes profit of the solar altitude tracking, which the shading blinds already have, to increase system performance. A dynamic energy simulation has been conducted in two different locations—Sde Boker (Israel) and Avignon (France)—both with adequate annual irradiances for solar applications, but with different weather and energy demand characteristics. The simulation engine utilized has been TRNSYS, coupled with MATLAB (where the ray-tracing algorithm to simulate the holographic optical performance has been implemented). The concentrator achieves annual mean optical efficiencies of 30.3% for Sde Boker and 43.0% for the case of Avignon. Regarding the energy production, in both locations the thermal energy produced meets almost 100% of the domestic hot water demand as this has been considered a priority in the system control. On the other hand, the space heating demands are covered by a percentage ranging from 15% (Avignon) to 20% (Sde Boker). Finally, the electricity produced in both places covers 7.4% of the electrical demand profile for Sde Boker and 9.1% for Avignon., This research was supported by ‘Ministerio de Economía y Competitividad’ of Spain for the funding (grants ENE2013-48325-R and BES-2014-069596), the Generalitat de Catalunya (grant 2016 FI_B1 00019), the UdL-Santander Bank (UdL-Impuls grant) and the Diputación General de Aragón-Fondo Social Europeo (TOL research group, T76).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Dielectric-based 3D building-integrated concentrating photovoltaic modules: An environmental life-cycle assessment

  • Baig, Hasan
  • Lamnatou, Chrysovalantou
  • Chemisana Villegas, Daniel
  • Mallick, Tapas K.
The environmental profile of a dielectric-based 3D Building-Integrated Concentrating Photovoltaic(BICPV) device is investigated. Several scenarios and life-cycle impact assessment methods are adopted,including the newly-developed method ReCiPe. Multiple environmental indicators are evaluated fordifferent cities: Barcelona, Seville, Paris, Marseille, London and Aberdeen. The results from the mate-rial manufacturing phase demonstrate that the PV cells and the concentrator are the components withthe highest contribution to the total impact of the BICPV, based on ReCiPe, Eco-indicator 99, USEtox,CED (cumulative energy demand), GWP (global warming potential) according to different time hori-zons (20a, 100a, 500a) and Ecological footprint. Among the studied cities, Barcelona, Marseille andSeville present the lowest GWP and CED: less than 142 g CO2.eq/kWh and less than 2.9 MJprim/kWh,based on all the studied scenarios. Moreover, by considering 30-years lifespan, Barcelona, Marseille andSeville show 0.0107–0.0111 ReCiPe Pts/kWh while London, Paris and Aberdeen present 0.0161-0.0173ReCiPe Pts/kWh. Results about greenhouse-gas-, energy-, ReCiPe-payback times and energy-return-on-investment are also presented and critically discussed. In addition, comparisons with the literature andissues for the improvement of the environmental profile of the proposed system are included., The authors would like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant reference ENE2013-48325-R).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Mid-infrared emissivity of crystalline silicon solar cells

  • Riverola Lacasta, Alberto
  • Mellor, A.
  • Alonso Alvarez, D.
  • Ferre Llin, L.
  • Guarracino, I.
  • Markides, C. N.
  • Paul, D. J.
  • Chemisana Villegas, Daniel
  • Ekins-Daukes, N.
The thermal emissivity of crystalline silicon photovoltaic (PV) solar cells plays a role in determining the operating temperature of a solar cell. To elucidate the physical origin of thermal emissivity, we have made an experimental measurement of the full radiative spectrum of the crystalline silicon (c-Si) solar cell, which includes both absorption in the ultraviolet to near-infrared range and emission in the mid-infrared. Using optical modelling, we have identified the origin of radiative emissivity in both encapsulated and unencapsulated solar cells. We find that both encapsulated and unencapsulated c-Si solar cells are good radiative emitters but achieve this through different effects. The emissivity of an unencapsulated c-Si solar cell is determined to be 75% in the MIR range, and is dominated by free-carrier emission in the highly doped emitter and back surface field layers; both effects are greatly augmented through the enhanced optical outcoupling arising from the front surface texture. An encapsulated glass-covered cell has an average emissivity around 90% on the MIR, and dips to 70% at 10 µm and is dominated by the emissivity of the cover glass. These findings serve to illustrate the opportunity for optimising the emissivity of c-Si based collectors, either in conventional c-Si PV modules where high emissivity and low-temperature operation is desirable, or in hybrid PV-thermal collectors where low emissivity enables a higher thermal output to be achieved., This research was supported by the 'Ministerio de Economía y Competitividad' of Spain (grants ENE2013-48325-R, BES-2014-069596 and EEBB-I-16-11459) and the by the UK Engineering and Physical Science Research Council (EPSRC) [grant number EP/M025012/1]. A. Mellor was supported by the European Commission through Marie Sklodowska Curie International Fellowship, Grant No. DLV-657359. Re fl ection and Transmission measurements were performed by Dr. Volker Kübler in the Micro-structured Surfaces Group of Fraunhofer- ISE, Freiburg, Germany.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Holographic solar energy systems: The role of optical elements

  • Collados, María Victoria
  • Chemisana Villegas, Daniel
  • Atencia Carrizo, Jesús
The use of holographic optical elements for solar energy applications has increased interest in the recent years because of their potential to reduce production cost, their ability to select certain bandwidths of the solar spectrum and their suitability for architectural integration. Among the different typologies of holograms, volume holograms are the most widely utilised devices due to their high efficiency (up to 100%) and also because they have two important characteristics: angular selectivity and chromatic selectivity, which are crucial for the design of systems addressed for lighting, solar shading or solar concentrators. In the present article, an analysis of the main existing holographic solar energy systems is presented, with emphasis on the characteristics of the optical element. (C) 2016 Elsevier Ltd. All rights reserved., This research has been supported by the Diputación General de Aragón (Consolidated Group TOL, T76) and the Spanish Ministries of Science and Technology (grant FIS2012-35433) and Economy and Competitiveness (grant ENE2013-48325-R).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Building-integrated solar thermal systems based on vacuum-tube technology: Critical factors focusing on life-cycle environmental profile

  • Lamnatou, Chrysovalantou
  • Cristofari, Christian A.
  • Chemisana Villegas, Daniel
  • Canaletti, J. L.
The present study refers to Building-Integrated Solar Thermal (BIST) systems based on vacuum-tube collectors and it consists of two parts. In the first part, a literature review is presented, including studies about vacuum-tube technology (vacuum-tube/BIST systems, the environmental profile of vacuum-tube collectors, etc.). Critical issues, for example related to the integration of vacuum-tube collectors into the building, are highlighted. The review shows that most of the proposed vacuum-tube/BIST concepts are about façade-integration and there are few studies about the environmental profile of vacuum-tube collectors. As a continuity of the issues presented in the first part, the second part includes a case study about the environmental comparison of a vacuum-tube/BIST system with a flat-plate/BIST configuration, based on life cycle assessment. The systems are gutter-integrated, patented and they have been developed/tested at the University of Corsica, in France. Multiple life-cycle impact assessment methodologies, environmental indicators, scenarios and databases are adopted. The results reveal that the energy-payback time is 1.8 and 0.5 years, for the flat-plate/BIST and for the vacuum-tube/BIST, respectively, while by using recycling these values become 0.5 and 0.1 years, respectively. Energy-return-on-investment, greenhouse-gas payback time and avoided impact during use phase (by adopting USEtox, ecological footprint and France´s electricity as well as with reference domestic-gas-boiler CO2.eq emissions) are also presented. The findings of the present work: 1) are compared with the literature and good agreement is observed, 2) verify that considerably higher impact can be avoided by utilizing the vacuum-tube/BIST instead of the flat-plate/BIST system., The authors would like to acknowledge networking support by the COST Action TU1205 Building Integration of Solar Thermal Systems. The authors would also like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant reference ENE2013-48325-R).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Concentrating solar systems: Life Cycle Assessment (LCA) and environmental issues

  • Lamnatou, Chrysovalantou
  • Chemisana Villegas, Daniel
The present article is a critical literature review about studies which are based on LCA (life cycle assessment) and about studies which include environmental issues about concentrating solar systems (concentrating photovoltaic (CPV), concentrating solar power (CSP), etc.). The results reveal that CPV environmental profile depends on several factors such as the materials of the concentrator and the direct solar radiation. On the other hand, there are different factors which influence CSP profile (from environmental point of view), including water use and materials e.g. for storage. By considering the literature review presented it can be noted that: 1) Regarding CPV, there is a need for more studies which investigate different concentration ratios, CPVT (concentrating photovoltaic/thermal) systems, low-concentration CPV, strategies to reduce the impact of certain components such as the tracking (especially for large-scale applications) and the concentrators, 2) Concerning CSP, there is a need for more investigations about dish-Stirling, storage materials, strategies for water savings, soiling effect, 3) In general, regarding concentrating solar systems, there is a need for more studies with Fresnel lenses and reflectors, for small-scale systems for buildings and for multiple final applications (desalination, drying, etc.), 4) With respect to the adopted methods/environmental indicators, certainly CO2.eq emissions, embodied energy and EPBT (energy payback time) can provide useful information for concentrating solar systems; nevertheless, there is a need for utilization of additional methods (e.g. based on midpoint, endpoint approaches) which can also offer useful information., The authors would like to thank ''Ministerio de Economía y Competitividad'' of Spain for the funding (grant reference ENE2013-48325-R).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental performance of a fresnel-transmission pvt concentrator for building-façade integration

  • Chemisana Villegas, Daniel
  • Rosell Urrutia, Joan Ignasi
  • Riverola Lacasta, Alberto
  • Lamnatou, Chrysovalantou
A building-façade integrated concentrating photovoltaic-thermal system has been designed, constructed and experimentally characterised. Comparative performances with a non-concentration reference unit have been conducted to analyse the differential outputs. The concentrating system consists of double-side reflective strips which concentrate the incident beam towards a static photovoltaic-thermal receiver. The reflectors are placed vertically at the façade and track the sun by rotating axially. The concentrating reflector outperforms the reference one in both, thermal and electrical power. The thermal output of the concentration module almost doubles the reference one and the electrical power registered is more than 4.5 times in the case of the concentrating configuration., The authors would like to acknowledge the funding from “Ministerio de Economía y Competitividad” of Spain (grants ENE2013-48325-R and BES-2014-069596). The authors would also like to thank networking support by the COST Action TU1205 Building Integration of Solar Thermal Systems.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Fluid-based spectrally selective filters for direct immersed PVT solar systems in building applications

  • Chemisana Villegas, Daniel
  • Fernández, Eduardo F.
  • Riverola Lacasta, Alberto
  • Moreno Bellostes, Àlex
Liquid filters applied in hybrid photovoltaic-thermal (PVT) solar systems report potential benefits as they allow for selecting the wavelengths at which the solar cell operates with higher efficiency. Among the rest, low frequency photons are absorbed by the liquid, therefore not warming the cell up. In addition, direct immersion of photovoltaic cells in liquids enhances temperature control by cooling the cells under almost negligible contact resistance between the liquid and the cell. The characteristics of the liquids for direct immersed PVT application are described, defining an indicator (ideal filter window) to select the best liquid depending on the PV technology and the incident irradiance. Several liquids are assessed based on the required properties for the present application. As a conclusion, regarding optical, thermal, electrical and operational aspects, a mixture of deionized water and isopropyl alcohol results as proper candidate satisfying well all of them., The authors would like to thank ''Ministerio de Economía y Competitividad'' of Spain for the funding (grant references ENE2013- 48325-R and ENE2016-81040-R) and to “Generalitat de Catalunya, AGAUR” (grant reference 2017 SGR 1276).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Broadband behavior of transmission volume holographic optical elements for solar concentration

  • Bañares-Palacios, Paula
  • Álvarez-Álvarez, Samuel
  • Marín-Sáez, Julia
  • Collados, María-Victoria
  • Chemisana, Daniel
  • Atencia, Jesús
A ray tracing algorithm is developed to analyze the energy performance of transmission and phase volume holographic lenses that operate with broadband illumination. The agreement between the experimental data and the theoretical treatment has been tested. The model has been applied to analyze the optimum recording geometry for solar concentration applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Characterization of volume holographic optical elements recorded in Bayfol HX photopolymer for solar photovoltaic applications

  • Marín Sáez, Julia
  • Atencia Carrizo, Jesús
  • Chemisana Villegas, Daniel
  • Collados Collados, María Victoria
Volume Holographic Optical Elements (HOEs) present interesting characteristics for photovoltaic applications as they can select spectrum for concentrating the target bandwidth and avoiding non-desired wavelengths, which can cause the decrease of the performance on the cell, for instance by overheating it. Volume HOEs have been recorded on Bayfol HX photopolymer to test the suitability of this material for solar concentrating photovoltaic systems. The HOEs were recorded at 532 nm and provided a dynamic range, reaching close to 100% efficiency at 800 nm. The diffracted spectrum had a FWHM of 230 nm when illuminating at Bragg angle. These characteristics prove HOEs recorded on Bayfol HX photopolymer are suitable for concentrating solar light onto photovoltaic cells sensitive to that wavelength range.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Energy simulation of a holographic PVT concentrating system for building integration applications

  • Marín-Sáez, Julia
  • Chemisana, Daniel
  • Moreno, Álex
  • Riverola, Alberto
  • Atencia Carrizo, Jesús
  • Collados Collados, María Victoria
A building integrated holographic concentrating photovoltaic-thermal system has been optically and energetically simulated. The system has been designed to be superimposed into a solar shading louvre; in this way the concentrating unit takes profit of the solar altitude tracking, which the shading blinds already have, to increase system performance. A dynamic energy simulation has been conducted in two different locations—Sde Boker (Israel) and Avignon (France)—both with adequate annual irradiances for solar applications, but with different weather and energy demand characteristics. The simulation engine utilized has been TRNSYS, coupled with MATLAB (where the ray-tracing algorithm to simulate the holographic optical performance has been implemented). The concentrator achieves annual mean optical efficiencies of 30.3% for Sde Boker and 43.0% for the case of Avignon. Regarding the energy production, in both locations the thermal energy produced meets almost 100% of the domestic hot water demand as this has been considered a priority in the system control. On the other hand, the space heating demands are covered by a percentage ranging from 15% (Avignon) to 20% (Sde Boker). Finally, the electricity produced in both places covers 7.4% of the electrical demand profile for Sde Boker and 9.1% for Avignon.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Full modeling and experimental validation of cylindrical holographic lenses recorded in Bayfol HX photopolymer and partly operating in the transition regime for solar concentration

  • Marín-Sáez, J.
  • Atencia, J.
  • Chemisana, D.
  • Collados, M.V.
Concentrating photovoltaics for building integration can be successfully carried out with Holographic Optical Elements (HOEs) because of their behavior analogous to refractive optical elements and their tuning ability to the spectral range that the photovoltaic (PV) cell is sensitive to. That way, concentration of spectral ranges that would cause overheating of the cell is avoided. Volume HOEs are usually chosen because they provide high efficiencies. However, their chromatic selectivity is also very high, and only a small part of the desired spectral range reaches the PV cell. A novel approach is theoretically and experimentally explored to overcome this problem: the use of HOEs operating in the transition regime, which yield lower chromatic selectivity while keeping rather high efficiencies. A model that considers the recording material’s response, by determining the index modulation reached for each spatial frequency and exposure dosage, has been developed. It has been validated with experimental measurements of three cylindrical holographic lenses with different spatial frequency ranges recorded in Bayfol HX photopolymer. Simulations of systems comprising two lenses and a mono-c Si PV cell are carried out with the standard AM 1.5D solar spectrum. Promising results are obtained when using the system with lower spatial frequencies lenses: a total current intensity equal to 3.72 times the one that would be reached without the concentrator.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Energy analysis of holographic lenses for solar concentration

  • Marín-Sáez, Julia
  • Collados, M.Victoria
  • Chemisana, Daniel
  • Atencia, Jesús
The use of volume and phase holographic elements in the design of photovoltaic solar concentrators has become very popular as an alternative solution to refractive systems, due to their high efficiency, low cost and possibilities of building integration. Angular and chromatic selectivity of volume holograms can affect their behavior as solar concentrators. In holographic lenses, angular and chromatic selectivity varies along the lens plane. Besides, considering that the holographic materials are not sensitive to the wavelengths for which the solar cells are most efficient, the reconstruction wavelength is usually different from the recording one. As a consequence, not all points of the lens work at Bragg condition for a defined incident direction or wavelength. A software tool that calculates the direction and efficiency of solar rays at the output of a volume holographic element has been developed in this study. It allows the analysis of the total energy that reaches the solar cell, taking into account the sun movement, the solar spectrum and the sensitivity of the solar cell. The dependence of the recording wavelength on the collected energy is studied with this software. As the recording angle is different along a holographic lens, some zones of the lens could not act as a volume hologram. The efficiency at the transition zones between volume and thin behavior in lenses recorded in Bayfol HX is experimentally analyzed in order to decide if the energy of generated higher diffraction orders has to be included in the simulation.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Energetic simulation of a dielectric photovoltaic-thermal concentrator

  • Moreno Bellostes, Àlex
  • Riverola Lacasta, Alberto
  • Chemisana Villegas, Daniel
A solar concentrating photovoltaic-thermal (CPVT) module with cell immersion in dielectric liquid has been modelled and energetically simulated. The concentrator focuses radiation linearly by using a cylindrical shape optics made of polymethyl methacrylate. The geometric concentration is 12 suns with an optical efficiency of 76.14%. The dielectric fluid, deionized water, flows through the concentrator case fulfilling a double function: to concentrate and to cool the PV cells. The concentrator is designed to be superimposed in front of the windows in a 2-storey family house with 4-person occupancy. The system is modelled to partially cover thermal and electrical demands utilizing a radiant floor and a reversible air-air heat pump for space heating and cooling (SH&C) and an electrical circuit which combines direct consumption and battery storage. The system topology has been simulated for three locations (Lisbon, Barcelona and Genoa). Results indicate an appropriate performance of the system analyzed with DHW solar fractions in a range from around 61% to above 75%. The lowest corresponds to Genoa and the highest to Lisbon and Barcelona. Regarding SH&C solar fractions are also quite adequate with values ranging from 38.3% (Genoa) to above 60% (68.8% in Lisbon and 62.4% in Barcelona). Finally, SFs for electrical loads take a value of 44.09% in the case of Lisbon, 38.9% for Barcelona and 23.51% for Genoa., The authors would like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant references ENE2013-48325-R, ENE2016-81040-R and BES-2014-069596) and “Generalitat de Catalunya” for the grant 2017FI_B_01171.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Energy simulation of a holographic PVT concentrating system for building integration applications

  • Marín Sáez, Julia
  • Chemisana Villegas, Daniel
  • Moreno Bellostes, Àlex
  • Riverola Lacasta, Alberto
  • Atencia Carrizo, Jesús
  • Collados, María Victoria
A building integrated holographic concentrating photovoltaic-thermal system has been optically and energetically simulated. The system has been designed to be superimposed into a solar shading louvre; in this way the concentrating unit takes profit of the solar altitude tracking, which the shading blinds already have, to increase system performance. A dynamic energy simulation has been conducted in two different locations—Sde Boker (Israel) and Avignon (France)—both with adequate annual irradiances for solar applications, but with different weather and energy demand characteristics. The simulation engine utilized has been TRNSYS, coupled with MATLAB (where the ray-tracing algorithm to simulate the holographic optical performance has been implemented). The concentrator achieves annual mean optical efficiencies of 30.3% for Sde Boker and 43.0% for the case of Avignon. Regarding the energy production, in both locations the thermal energy produced meets almost 100% of the domestic hot water demand as this has been considered a priority in the system control. On the other hand, the space heating demands are covered by a percentage ranging from 15% (Avignon) to 20% (Sde Boker). Finally, the electricity produced in both places covers 7.4% of the electrical demand profile for Sde Boker and 9.1% for Avignon., This research was supported by ‘Ministerio de Economía y Competitividad’ of Spain for the funding (grants ENE2013-48325-R and BES-2014-069596), the Generalitat de Catalunya (grant 2016 FI_B1 00019), the UdL-Santander Bank (UdL-Impuls grant) and the Diputación General de Aragón-Fondo Social Europeo (TOL research group, T76).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Photovoltaic/thermal (PVT) systems: A review with emphasis on environmental issues

  • Lamnatou, Chrysovalantou
  • Chemisana Villegas, Daniel
The present article is a review about PVT (photovoltaic/thermal) investigations with emphasis on studies which include environmental issues about PVT technology. The references analyzed are presented according to certain criteria (e.g. the type of the system: BA (building-added), BI (building-integrated), CPVT (concentrating PVT), etc.). The literature review shows that most of the investigations examine EPBT (energy payback time) and CO2 emissions. In terms of the types of the systems, most of the studies are about BA PVT/water installations for domestic applications and thereby, more studies (which include environmental issues) are needed e.g. about BIPVT, CPVT, BICPVT and PVT systems for different applications (apart from the building sector), for example industrial. In addition, a separate section with factors which influence PVT from environmental point of view (PV cell material, heat transfer fluid, concentrators, alternative materials, etc.) is included. A critical discussion about these factors is also provided, explaining how they influence the environmental profile of a PVT system. Moreover, explanations about different methods and indicators which provide (or which can provide as a future prospect) useful information for PVT (from environmental point of view) are also presented., The authors would like to acknowledge networking support by the COST Action TU1205 Building Integration of Solar Thermal Systems. The authors would also like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant reference ENE2013-48325-R).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Full modeling and experimental validation of cylindrical holographic lenses recorded in Bayfol HX photopolymer and partly operating in the transition regime for solar concentration

  • Marín Sáez, Julia
  • Atencia Carrizo, Jesús
  • Chemisana Villegas, Daniel
  • Collados, María Victoria
Concentrating photovoltaics for building integration can be successfully carried out with Holographic Optical Elements (HOEs) because of their behavior analogous to refractive optical elements and their tuning ability to the spectral range that the photovoltaic (PV) cell is sensitive to. That way, concentration of spectral ranges that would cause overheating of the cell is avoided. Volume HOEs are usually chosen because they provide high efficiencies. However, their chromatic selectivity is also very high, and only a small part of the desired spectral range reaches the PV cell. A novel approach is theoretically and experimentally explored to overcome this problem: the use of HOEs operating in the transition regime, which yield lower chromatic selectivity while keeping rather high efficiencies. A model that considers the recording material’s response, by determining the index modulation reached for each spatial frequency and exposure dosage, has been developed. It has been validated with experimental measurements of three cylindrical holographic lenses with different spatial frequency ranges recorded in Bayfol HX photopolymer. Simulations of systems comprising two lenses and a mono-c Si PV cell are carried out with the standard AM 1.5D solar spectrum. Promising results are obtained when using the system with lower spatial frequencies lenses: a total current intensity equal to 3.72 times the one that would be reached without the concentrator., Generalitat de Catalunya (2017FI_B2_00127); Ministerio de Economía y Competitividad of Spain (ENE2013-48325-R, ENE2016-81040-R); Diputación General de Aragón - Fondo Social Europeo (TOL research group, T76); Universidad de Zaragoza (UZ2017-CIE-02).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Mid-infrared emissivity of crystalline silicon solar cells

  • Riverola Lacasta, Alberto
  • Mellor, A.
  • Alonso Alvarez, D.
  • Ferre Llin, L.
  • Guarracino, I.
  • Markides, C. N.
  • Paul, D. J.
  • Chemisana Villegas, Daniel
  • Ekins-Daukes, N.
The thermal emissivity of crystalline silicon photovoltaic (PV) solar cells plays a role in determining the operating temperature of a solar cell. To elucidate the physical origin of thermal emissivity, we have made an experimental measurement of the full radiative spectrum of the crystalline silicon (c-Si) solar cell, which includes both absorption in the ultraviolet to near-infrared range and emission in the mid-infrared. Using optical modelling, we have identified the origin of radiative emissivity in both encapsulated and unencapsulated solar cells. We find that both encapsulated and unencapsulated c-Si solar cells are good radiative emitters but achieve this through different effects. The emissivity of an unencapsulated c-Si solar cell is determined to be 75% in the MIR range, and is dominated by free-carrier emission in the highly doped emitter and back surface field layers; both effects are greatly augmented through the enhanced optical outcoupling arising from the front surface texture. An encapsulated glass-covered cell has an average emissivity around 90% on the MIR, and dips to 70% at 10 µm and is dominated by the emissivity of the cover glass. These findings serve to illustrate the opportunity for optimising the emissivity of c-Si based collectors, either in conventional c-Si PV modules where high emissivity and low-temperature operation is desirable, or in hybrid PV-thermal collectors where low emissivity enables a higher thermal output to be achieved., This research was supported by the 'Ministerio de Economía y Competitividad' of Spain (grants ENE2013-48325-R, BES-2014-069596 and EEBB-I-16-11459) and the by the UK Engineering and Physical Science Research Council (EPSRC) [grant number EP/M025012/1]. A. Mellor was supported by the European Commission through Marie Sklodowska Curie International Fellowship, Grant No. DLV-657359. Re fl ection and Transmission measurements were performed by Dr. Volker Kübler in the Micro-structured Surfaces Group of Fraunhofer- ISE, Freiburg, Germany.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dielectric-based 3D building-integrated concentrating photovoltaic modules: An environmental life-cycle assessment

  • Baig, Hasan
  • Lamnatou, Chrysovalantou
  • Chemisana Villegas, Daniel
  • Mallick, Tapas K.
The environmental profile of a dielectric-based 3D Building-Integrated Concentrating Photovoltaic(BICPV) device is investigated. Several scenarios and life-cycle impact assessment methods are adopted,including the newly-developed method ReCiPe. Multiple environmental indicators are evaluated fordifferent cities: Barcelona, Seville, Paris, Marseille, London and Aberdeen. The results from the mate-rial manufacturing phase demonstrate that the PV cells and the concentrator are the components withthe highest contribution to the total impact of the BICPV, based on ReCiPe, Eco-indicator 99, USEtox,CED (cumulative energy demand), GWP (global warming potential) according to different time hori-zons (20a, 100a, 500a) and Ecological footprint. Among the studied cities, Barcelona, Marseille andSeville present the lowest GWP and CED: less than 142 g CO2.eq/kWh and less than 2.9 MJprim/kWh,based on all the studied scenarios. Moreover, by considering 30-years lifespan, Barcelona, Marseille andSeville show 0.0107–0.0111 ReCiPe Pts/kWh while London, Paris and Aberdeen present 0.0161-0.0173ReCiPe Pts/kWh. Results about greenhouse-gas-, energy-, ReCiPe-payback times and energy-return-on-investment are also presented and critically discussed. In addition, comparisons with the literature andissues for the improvement of the environmental profile of the proposed system are included., The authors would like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant reference ENE2013-48325-R).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Concentrating solar systems: Life Cycle Assessment (LCA) and environmental issues

  • Lamnatou, Chrysovalantou
  • Chemisana Villegas, Daniel
The present article is a critical literature review about studies which are based on LCA (life cycle assessment) and about studies which include environmental issues about concentrating solar systems (concentrating photovoltaic (CPV), concentrating solar power (CSP), etc.). The results reveal that CPV environmental profile depends on several factors such as the materials of the concentrator and the direct solar radiation. On the other hand, there are different factors which influence CSP profile (from environmental point of view), including water use and materials e.g. for storage. By considering the literature review presented it can be noted that: 1) Regarding CPV, there is a need for more studies which investigate different concentration ratios, CPVT (concentrating photovoltaic/thermal) systems, low-concentration CPV, strategies to reduce the impact of certain components such as the tracking (especially for large-scale applications) and the concentrators, 2) Concerning CSP, there is a need for more investigations about dish-Stirling, storage materials, strategies for water savings, soiling effect, 3) In general, regarding concentrating solar systems, there is a need for more studies with Fresnel lenses and reflectors, for small-scale systems for buildings and for multiple final applications (desalination, drying, etc.), 4) With respect to the adopted methods/environmental indicators, certainly CO2.eq emissions, embodied energy and EPBT (energy payback time) can provide useful information for concentrating solar systems; nevertheless, there is a need for utilization of additional methods (e.g. based on midpoint, endpoint approaches) which can also offer useful information., The authors would like to thank ''Ministerio de Economía y Competitividad'' of Spain for the funding (grant reference ENE2013-48325-R).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Characterization of volume holographic optical elements recorded in Bayfol HX photopolymer for solar photovoltaic applications

  • Marín Sáez, Julia
  • Atencia Carrizo, Jesús
  • Chemisana Villegas, Daniel
  • Collados, María Victoria
Volume Holographic Optical Elements (HOEs) present interesting characteristics for photovoltaic applications as they can select spectrum for concentrating the target bandwidth and avoiding non-desired wavelengths, which can cause the decrease of the performance on the cell, for instance by overheating it. Volume HOEs have been recorded on Bayfol HX photopolymer to test the suitability of this material for solar concentrating photovoltaic systems. The HOEs were recorded at 532 nm and provided a dynamic range, reaching close to 100% efficiency at 800 nm. The diffracted spectrum had a FWHM of 230 nm when illuminating at Bragg angle. These characteristics prove HOEs recorded on Bayfol HX photopolymer are suitable for concentrating solar light onto photovoltaic cells sensitive to that wavelength range., This research has been supported by the Spanish Ministerio de Economía y Competitividad (grants ENE2013-48325-R and FIS2012-35433), the Diputación General de Aragón-Fondo Social Europeo (TOL research group, T76) and the Generalitat de Catalunya (grant 2015 FI_B 00328).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fluid-based spectrally selective filters for direct immersed PVT solar systems in building applications

  • Chemisana Villegas, Daniel
  • Fernández, Eduardo F.
  • Riverola Lacasta, Alberto
  • Moreno Bellostes, Àlex
Liquid filters applied in hybrid photovoltaic-thermal (PVT) solar systems report potential benefits as they allow for selecting the wavelengths at which the solar cell operates with higher efficiency. Among the rest, low frequency photons are absorbed by the liquid, therefore not warming the cell up. In addition, direct immersion of photovoltaic cells in liquids enhances temperature control by cooling the cells under almost negligible contact resistance between the liquid and the cell. The characteristics of the liquids for direct immersed PVT application are described, defining an indicator (ideal filter window) to select the best liquid depending on the PV technology and the incident irradiance. Several liquids are assessed based on the required properties for the present application. As a conclusion, regarding optical, thermal, electrical and operational aspects, a mixture of deionized water and isopropyl alcohol results as proper candidate satisfying well all of them., The authors would like to thank ''Ministerio de Economía y Competitividad'' of Spain for the funding (grant references ENE2013- 48325-R and ENE2016-81040-R) and to “Generalitat de Catalunya, AGAUR” (grant reference 2017 SGR 1276).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Holographic solar energy systems: The role of optical elements

  • Collados, María Victoria
  • Chemisana Villegas, Daniel
  • Atencia Carrizo, Jesús
The use of holographic optical elements for solar energy applications has increased interest in the recent years because of their potential to reduce production cost, their ability to select certain bandwidths of the solar spectrum and their suitability for architectural integration. Among the different typologies of holograms, volume holograms are the most widely utilised devices due to their high efficiency (up to 100%) and also because they have two important characteristics: angular selectivity and chromatic selectivity, which are crucial for the design of systems addressed for lighting, solar shading or solar concentrators. In the present article, an analysis of the main existing holographic solar energy systems is presented, with emphasis on the characteristics of the optical element. (C) 2016 Elsevier Ltd. All rights reserved., This research has been supported by the Diputación General de Aragón (Consolidated Group TOL, T76) and the Spanish Ministries of Science and Technology (grant FIS2012-35433) and Economy and Competitiveness (grant ENE2013-48325-R).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Building-integrated solar thermal systems based on vacuum-tube technology: Critical factors focusing on life-cycle environmental profile

  • Lamnatou, Chrysovalantou
  • Cristofari, Christian A.
  • Chemisana Villegas, Daniel
  • Canaletti, J. L.
The present study refers to Building-Integrated Solar Thermal (BIST) systems based on vacuum-tube collectors and it consists of two parts. In the first part, a literature review is presented, including studies about vacuum-tube technology (vacuum-tube/BIST systems, the environmental profile of vacuum-tube collectors, etc.). Critical issues, for example related to the integration of vacuum-tube collectors into the building, are highlighted. The review shows that most of the proposed vacuum-tube/BIST concepts are about façade-integration and there are few studies about the environmental profile of vacuum-tube collectors. As a continuity of the issues presented in the first part, the second part includes a case study about the environmental comparison of a vacuum-tube/BIST system with a flat-plate/BIST configuration, based on life cycle assessment. The systems are gutter-integrated, patented and they have been developed/tested at the University of Corsica, in France. Multiple life-cycle impact assessment methodologies, environmental indicators, scenarios and databases are adopted. The results reveal that the energy-payback time is 1.8 and 0.5 years, for the flat-plate/BIST and for the vacuum-tube/BIST, respectively, while by using recycling these values become 0.5 and 0.1 years, respectively. Energy-return-on-investment, greenhouse-gas payback time and avoided impact during use phase (by adopting USEtox, ecological footprint and France´s electricity as well as with reference domestic-gas-boiler CO2.eq emissions) are also presented. The findings of the present work: 1) are compared with the literature and good agreement is observed, 2) verify that considerably higher impact can be avoided by utilizing the vacuum-tube/BIST instead of the flat-plate/BIST system., The authors would like to acknowledge networking support by the COST Action TU1205 Building Integration of Solar Thermal Systems. The authors would also like to thank “Ministerio de Economía y Competitividad” of Spain for the funding (grant reference ENE2013-48325-R).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Environmental assessment of a pork-production system in North-East of Spain focusing on life-cycle swine nutrition

  • Lamnatou, Chrysovalantou
  • Ezcurra Ciaurriz, F. Xavier
  • Chemisana Villegas, Daniel
  • Pla Aragonés, Lluís Miquel
Given the importance of pig-meat production in Spain, the present work (based on cumulative energy demand, global warming potential, ReCiPe method and different functional units) presents a life cycle assessment of an intensive pork-production system (growing-finishing pigs from 25 to 105 kg body weight) in North-East of Spain. Emphasis is given on animal feeding (which is separated into 3 phases) while the impact of drinking-water consumption, straw usage and transportation (for feed and straw) are also taken into account for certain scenarios. The results demonstrate that there is a cumulative energy demand of 5.6 MJprim per kg of animal feed and 14.5-35.6 MJprim per kg of meat (live or carcass weight). Moreover, global warming potential (based on a time horizon of 100 years: 100a) is 3.2-5.5 kg CO2.eq per kg of meat (live or carcass weight) and 336-460 kg CO2.eq per market pig. On the other hand, ReCiPe impact per market pig ranges from 60 to 76 Pts, depending on the scenario. Based on all the studied cases, animal feed is responsible for the greatest part of the total impact feed/drinking-water/straw/transportation and transportation is responsible for the second highest impact. A comparison with results from the literature is also provided and critical issues (about feed composition, cleaner-production solutions, etc.) are presented., The authors would like to thank ''Ministerio de Economía y Competitividad'' of Spain for the funding (grant reference ENE2013-48325-R). Lluis M. Plà-Aragonés wishes to acknowledge the financial support of the Spanish Research ProgramTRA2013-48180-C3-P and CYTED program support to the thematic network P515RT0123.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental performance of a fresnel-transmission pvt concentrator for building-façade integration

  • Chemisana Villegas, Daniel
  • Rosell Urrutia, Joan Ignasi
  • Riverola Lacasta, Alberto
  • Lamnatou, Chrysovalantou
A building-façade integrated concentrating photovoltaic-thermal system has been designed, constructed and experimentally characterised. Comparative performances with a non-concentration reference unit have been conducted to analyse the differential outputs. The concentrating system consists of double-side reflective strips which concentrate the incident beam towards a static photovoltaic-thermal receiver. The reflectors are placed vertically at the façade and track the sun by rotating axially. The concentrating reflector outperforms the reference one in both, thermal and electrical power. The thermal output of the concentration module almost doubles the reference one and the electrical power registered is more than 4.5 times in the case of the concentrating configuration., The authors would like to acknowledge the funding from “Ministerio de Economía y Competitividad” of Spain (grants ENE2013-48325-R and BES-2014-069596). The authors would also like to thank networking support by the COST Action TU1205 Building Integration of Solar Thermal Systems.