Pasar al contenido principal

MODELACION Y EXPERIMENTACION EN FLUJO ANULAR Y EN TRANSICION EN SISTEMAS ENERGETICOS

ENE2013-48565-C2-1-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of Conductivity Sensors for Multi-Phase Flow Local Measurements at the Polytechnic University of Valencia (UPV) and University Jaume I of Castellon (UJI)

  • Muñoz-Cobo, J. L.
  • Chiva, Sergio
  • Mendez, Santos
  • Monrós, Guillem
  • Escrivá, A.
  • Cuadros-Orón, José Luis
[EN] This paper describes all the procedures and methods currently used at UPV (Universitat Politécnica de Valencia) and UJI (University Jaume I) for the development and use of sensors for multi-phase flow analysis in vertical pipes. This paper also describes the methods that we use to obtain the values of the two-phase flow magnitudes from the sensor signals and the validation and cross-verification methods developed to check the consistency of the results obtained for these magnitudes with the sensors. First, we provide information about the procedures used to build the multi-sensor conductivity probes and some of the tests performed with different materials to avoid sensor degradation issues. In addition, we provide information about the characteristics of the electric circuits that feed the sensors. Then the data acquisition of the conductivity probe, the signal conditioning and the data processing including the device that have been designed to automatize all the measurement process of moving the sensors inside the channels by means of stepper electric motors controlled by computer are shown in operation. Then, we explain the methods used for bubble identification and categorization. Finally, we describe the methodology used to obtain the two-phase flow information from the sensor signals. This includes the following items: void fraction, gas velocity, Sauter mean diameter and interfacial area concentration. The last part of this paper is devoted to the conductance probes developed for the annular flow analysis, which includes the analysis of the interfacial waves produced in annular flow and that requires a different type of sensor, The authors are indebted to the support received from MINECO for the project MODEXFLAT ENE2013-48565-C2-1-P and ENE2013-48565-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A CFD-DEM solver to model bubbly flow. Part II: Critical validation in upward vertical pipes including axial evolution

  • Peña-Monferrer, Carlos
  • Monrós-Andreu, Guillem
  • Chiva Vicent, Sergio
  • Martinez-Cuenca, R.
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
[EN] In the computational modeling of two-phase flow, many uncertainties are usually faced in simulations and validations with experiments. This has traditionally made it difficult to provide a general method to predict the two-phase flow characteristics for any geometry and condition, even for bubbly flow regimes. Thus, we focus our research on studying in depth the bubbly flow modeling and validation from a critical point of view. The conditions are intentionally limited to scenarios where coalescence and breakup can be neglected, to concentrate on the study of bubble dynamics and its interaction with the main fluid. This study required the development of a solver for bubbly flow with higher resolution level than TFM and a new methodology to obtain the data from the simulation. In Part II, taking profit of the detailed data provided by the CFD-DEM solver presented in Part I, we propose a novel methodology based on virtual sensor probes, to perform a rigorous validation and to investigate the experimental data. The same approximation used for processing the experimental datasets applies to simulation data, then the same assumptions are considered. In this way we can study an extended number of disperse phase variables as bubble velocity, void fraction, interfacial area concentration, mean chord length and distribution, Sauter mean diameter, bubble frequency and missing ratio, in addition to other variables as bubble size distribution or carrier phase velocity and turbulence. Several upward bubbly flow scenarios from datasets of different authors are used to validate the solver using this methodology. Finally, an axial evolution validation is performed including a discussion motivated by the comparison between experiments and the data from the virtual probes. (C) 2017 Elsevier Ltd. All rights reserved., The authors sincerely thank the "Plan Nacional de I + D+i" for funding the project MODEXFLAT ENE2013-48565-C2-1-P and ENE2013-48565-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A CFD-DEM solver to model bubbly flow. Part I: Model development and assessment in upward vertical pipes

  • Peña-Monferrer, Carlos
  • Monrós Andreu, Guillem
  • Chiva Vicent, Sergio
  • Martinez-Cuenca, R.
  • Muñoz-Cobo, J. L.
[EN] In the computational modeling of two-phase flow, many uncertainties are usually faced in simulations and validations with experiments. This has traditionally made it difficult to provide a general method to predict the two-phase flow characteristics for any geometry and condition, even for bubbly flow regimes. Thus, we focus our research on studying in depth the bubbly flow modeling and validation from a critical point of view. The conditions are intentionally limited to scenarios where coalescence and breakup can be neglected, to concentrate on the study of bubble dynamics and its interaction with the main fluid. This study required the development of a solver for bubbly flow with higher resolution level than TFM and a new methodology to obtain the data from the simulation. Part I shows the development of a solver based on the CFD-DEM formulation. The motion of each bubble is computed individually with this solver and aspects as inhomogeneity, nonlinearity of the interfacial forces, bubble-wall interactions and turbulence effects in interfacial forces are taken into account. To develop the solver, several features that are not usually required for traditional CFD-DEM simulations but are relevant for bubbly flow in pipes, have been included. Models for the assignment of void fraction into the grid, seeding of bubbles at the inlet, pressure change influence on the bubble size and turbulence effects on both phases have been assessed and compared with experiments for an upward vertical pipe scenario. Finally, the bubble path for bubbles of different size have been investigated and the interfacial forces analyzed. (C) 2017 Elsevier Ltd. All rights reserved., The authors sincerely thank the ''Plan Nacional de I + D+ i" for funding the project MODEXFLAT ENE2013-48565-C2-1-P and ENE2013-48565-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental investigation of the entrained droplet velocities in a submerged jet injected into a stagnant water pool

  • Berna-Escriche, César|||0000-0002-2097-5089
  • Escrivá, A.|||0000-0002-9670-068X
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
  • Pastor, José V.|||0000-0003-4113-4681
  • Micó, Carlos|||0000-0001-5787-6212
  • Juliá, J.E.
[EN] Round turbulent air jets submerged in stagnant water have been studied experimentally in this paper. To achieve this objective a water pool with an air injector has been built and particle image velocimetry visualization techniques (PIV) have been employed to capture images of the submerged jet throughout its spreading. From these images one of the most important variables that characterizes submerged jets the velocity of the entrained droplets, was determined, finding that the function which best fits the entrained droplet velocity distribution is a decreasing exponential function. In addition, a correlation that relates the initial submerged gaseous jet properties, via the gas Reynolds number, with the entrained droplet velocities was developed, in this case via the entrained droplet Reynolds number. (C) 2016 Elsevier Inc. All rights reserved., The authors are indebted to the financial support of MODEX-FLAT project, reference: ENE2013-48565-C2-1-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Aplicación de la metodología de escalado a una rotura de pequeño tamaño entre la instalación experimental ROSA-LSTF y una planta PWR de 3 lazos del tipo Siemens-KWU, Application of the scaling methodology to a small size break between the experimentalo facility ROSA-LSTF and a 3-Loop PWR plant of the Siemens-KWU type

  • Berna-Escriche, César|||0000-0002-2097-5089
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
  • Escrivá, A.|||0000-0002-9670-068X
[ES] La metodología de escalado consiste en una descripción cuantitativa de las condiciones que se deben cumplir en una instalación experimental para poder reproducir adecuadamente el comportamiento de una planta comercial. El análisis de escala top-down de la metodología H2TS se ha aplicado a una rotura de pequeño tamaño en la rama caliente entre la instalación experimental LSTF-ROSA y un reactor comercial de distinto tipo al de referencia de esta (planta de referencia tipo Westinghouse, aplicada a tipo Siemens-KWU). Las cinco etapas fundamentales de un LOCA se han analizado, habiéndose calculado un total de 53 grupos de escala (monomios ¿)., [EN] The scaling methodology consists of a quantitative description of the conditions that must be met in an experimental facility to adequately reproduce the behavior of a commercial plant. The ¿top-down¿ scaling analysis of the H2TS methodology has been applied to a small size break in the hot leg between the LSTF-ROSA experimental facility and a commercial reactor of different type to its reference plant (reference plant is a Westinghouse, applied to a Siemens-KWU type). The five fundamental stages of a LOCA have been analyzed, having been calculated a total of 53 scaling groups (p-monomials)., Los autores quieren agradecer el soporte financiero del proyecto MODEXFLAT, referencia: ENE2013-48565-C2-1-P y el soporte financiero del Consejo de Seguridad Nuclear (CSN). Agradecer a JAERI por proporcionar los datos experimentales a través del proyecto CAMP-OECD
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the One-Dimensional Modeling of Vertical Upward Bubbly Flow

  • Peña-Monferrer, C.
  • Gómez-Zarzuela, C.
  • Chiva, S.
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
[EN] The one-dimensional two-fluid model approach has been traditionally used in thermal-hydraulics codes for the analysis of transients and accidents in water¿cooled nuclear power plants. This paper investigates the performance of RELAP5/MOD3 predicting vertical upward bubbly flow at low velocity conditions. For bubbly flow and vertical pipes, this code applies the drift- velocity approach, showing important discrepancies with the experiments compared. Then, we use a classical formulation of the drag coefficient approach to evaluate the performance of both approaches. This is based on the critical Weber criteria and includes several assumptions for the calculation of the interfacial area and bubble size that are evaluated in this work. A more accurate drag coefficient approach is proposed and implemented in RELAP5/MOD3. Instead of using the Weber criteria, the bubble size distribution is directly considered. This allows the calculation of the interfacial area directly from the definition of Sauter mean diameter of a distribution. The results show that only the proposed approach was able to predict all the flow characteristics, in particular the bubble size and interfacial area concentration. Finally, the computational results are analyzed and validated with cross-section area average measurements of void fraction, dispersed phase velocity, bubble size, and interfacial area concentration., The authors sincerely thank the Plan Nacional de I+D+i for funding the Projects MODEXFLAT ENE2013-48565-C2-1- P, ENE2013-48565-C2-2-P, and NUC-MULTPHYS ENE2012- 34585.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Top-down scaling methodology from the LSTF facility to a three loop PWR plant applied to a SBLOCA event - The ROSA 1.2 test

  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
  • Berna-Escriche, César|||0000-0002-2097-5089
  • Escrivá, A.|||0000-0002-9670-068X
[EN] The scaling methodology describes quantitatively the possible differences in the behavior between a reduced size experimental facility and a full scale commercial plant for a determined transient. Then scaling is an essential tool in the design and operation processes of a reduced size facility in order to be able to simulate the behavior of large commercial plants. Since, in this way, it is possible to advance in the development of safety systems, prediction of situations likely to produce accidental sequences, etcetera. Therefore the scaling calculations should be carried out from the earlier stages of the experimental facility conceptual design, so that its experimental data results could be directly extrapolated to a commercial plant. Evidently, the scaling analysis has to be carried out for the experimental test plans, in order to check the capacity to transpose the experimental data of the reduced size facilities to the commercial plants. Consequently, the major objective of the scaling methodology is to evaluate quantitatively the applicability of small size test facility data to predict the behavior of full size commercial plants. The top-down scaling step of the H2TS scaling methodology, between the LSTF experimental facility and a Pressurized Water Reactor of Siemens-KWU type for the ROSA 1.2 test, has been carried out along this document to evaluate the global system behavior. In order to achieve this main purpose, the general description of both facilities, the transient scenario, and the results of the scaling analysis for a small break loss of coolant accident (SBLOCA) in the hot leg are shown. The scaling analysis methodology used is the top-down global system analysis, from which, it is intended to establish thermal-hydraulic similarity between a scaled facility and a full scale industrial plant. With this aim, the accidental sequence of the ROSA 1.2 test has been divided into its five main time phases, analyzing separately each of them. In each phase the similarity groups (pi-monomials and pi-monomial groups) have been defined and applied. In such a way that only a reduced number pi-monomials are needed to develop the scaling methodology, in addition, many of these similarity groups appear in several phases. The key aspect of this document is to show the applicability of the top-down scaling analysis methodology to a commercial plant of a different type to that of the reference NPP at which the experimental facility replicates, i.e., test carried out in a Westinghouse type experimental facility, scaling analysis applied to a Siemens-KWU type. In such a way that, it has been proved the possibility to use the measurements facility of different type of the reference plant for an accidental scenario, in particular, applicability of a SBLOCA test data from an experimental facility of type Westinghouse to a commercial plant of type Siemens-KWU., The authors are indebted to the financial support of MODEXFLAT project, reference: ENE2013-48565-C2-1-P and the financial support of the Spanish Regulatory Commission (CSN). We are also indebted to JAERI by providing the experimental data through the CAMP-OECD project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancement of the SPARC90 code to pool scrubbing events under jet injection regime

  • Berna-Escriche, César|||0000-0002-2097-5089
  • Escrivá, A.|||0000-0002-9670-068X
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
  • Herranz, Luis Enrique
[EN] Submerged gaseous jets may have an outstanding relevance in many industrial processes and may be of particular significance in severe nuclear accident scenarios, like in the Fukushima accident. Even though pool scrubbing has been traditionally associated with low injection velocities, there are a number of potential scenarios in which fission product trapping in aqueous ponds might also occur under jet injection regime (like SGTR meltdown sequences in PWRs and SBO ones in BWRs). The SPARC90 code was developed to determine the fission product trapping in pools during severe accidents. The code assumes that carrier gas arrives at the water ponds at low or moderate velocities and it forms a big bubble that eventually detaches from the injection pipe. However, particle laden gases may enter the water at very high velocities resulting in a submerged gas jet instead. This work presents the fundamentals, major hypotheses and changes introduced into the code in order to estimate particle removal during gas injection in pools under the jet regime (SPARC90-Jet). A simplified and reliable approach to submerged jet hydrodynamics has been implemented on the basis of updated equations for jet hydrodynamics and aerosol removal, so that gas-liquid and droplet-particles interactions are described. The code modifications have been validated as far as possible. However, no suitable hydrodynamic tests have been found in the literature, so that an indirect validation has been conducted through comparisons against data from pool scrubbing experiments. Besides, this validation has been forcefully limited since very few pool scrubbing tests are available in the jet injection regime (i.e., ACE, LACE, POSEIDON II and RCA). But nevertheless, a considerable improvement in the estimation of the Decontamination Factor (DF) has been reached, as well as it has been proven that sizes of aerosol particles and submergencies are factors of major influence, however there is still a long road ahead. We have extended the SPARC90 capabilities to study jet discharge processes, then the new SPARC90-Jet version is able to study globular and jet discharge processes, i.e. pool discharges under low and high velocity conditions. Therefore, the work here presented should be understood as a promising first step toward an effective code extension to the jet regime, The authors are indebted to the financial support of MODEXFLAT project, reference: ENE2013-48565-C2-1-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CFD modelling and validation of upward bubbly flow in an adiabatic vertical pipe using the quadrature method of moments

  • Peña Monferrer, Carlos
  • Passalacqua, Alberto
  • Chiva Vicent, Sergio
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
[EN] An Eulerian-Eulerian approach was investigated to model adiabatic bubbly flow with CFD techniques. In the framework of the OpenFOAM (R) software, a two-fluid model solver was modified to include a population balance equation, solved with the quadrature method of moments approximation to predict upward bubbly flow in vertical pipes considering the polydisperse nature of two-phase flow. Some progress have been made recently solving population balance equations in OpenFOAM (R) and this research aims to extend its application to the case of vertical pipes under different conditions of liquid and gas velocities. In order to test the solver for nuclear applications, interfacial forces and bubble induced turbulence models were included to provide to this solver the capability to correctly predict the behavior of the continuous and disperse phases. Two-phase flow experiments with different superficial velocities of gas and liquid are used to validate the model and its implementation. Radial profiles of void fraction, gas and liquid velocities, Sauter mean diameter and turbulence intensity are compared to the computational results. These results are in satisfactory agreement with the experiments, showing the capability of the solver to predict two-phase flow characteristics., The authors sincerely thank the "Plan Nacional de I+D+i" Projects ENE2013-48565-C2-1-P and ENE2013-48565-C2-2-P for funding the project. C. Pena-Monferrer would like to thank the Department of Mechanical Engineering at Iowa State University for hosting him while performing part of this research work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modelling and experimental investigation of horizontal buoyant gas jets injected into stagnant uniform ambient liquid

  • Harby, K.
  • Chiva, S.
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
[EN] In this article, an experimental and theoretical study on the buoyant non-condensable gas jet that is injected horizontally into a high-density liquid ambient at different initial conditions is performed. Direct and instantaneous global measurements of the interface were performed using a high-speed photography. The position and motion of the entire gas jet were captured by a high-velocity camera and the images were processed, averaged and analyzed to extract the jet parameters and interface position. In the mathematical model, the rate of entrainment is assumed to be a function of the jet centerline velocity, the ratio of the mean jet and the ambient densities, while the entrainment coefficient depends on the local Froude number at the jet region. An interfacial shear stress acting at the interface between the jet flow and the water ambient in the opposed direction to the main jet momentum flux is considered. The results showed that the model is able to accurately predict the jet parameters: trajectory, spread, jet angles and penetration lengths as well as the jet regimes. An overall good agreement was obtained between the simulation and experimental results over a large range of Froude numbers and jet diameters. The developed model has proven to be an adequate tool to predict the different jet parameters., The authors of this paper are indebted to the National of I+D projects MODEXFLAT ENE2013-48565-C2-1-P and ENE2013-48565-C2-2-P.