Pasar al contenido principal

GESTION Y CONTROL DE MICRORREDES DE CORRIENTE ALTERNA E INTERCONEXION CON BUSES DE CONTINUA EN MICRORREDES HIBRIDAS

ENE2015-64087-C2-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 38
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Analysis of the effect of clock drifts on frequency regulation and power sharing in inverter-based islanded microgrids

  • Martí Colom, Pau|||0000-0002-5189-0782
  • Torres Martínez, Javier
  • Rosero Chandi, Carlos Xavier
  • Velasco García, Manel|||0000-0002-0764-3063
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Local hardware clocks in physically distributed computation devices hardly ever agree because clocks drift apart and the drift can be different for each device. This paper analyses the effect that local clock drifts have in the parallel operation of voltage source inverters (VSIs) in islanded microgrids (MG). The state-of-the-art control policies for frequency regulation and active power sharing in VSIs-based MGs are reviewed and selected prototype policies are then re-formulated in terms of clock drifts. Next, steady-state properties for these policies are analyzed. For each of the policies, analytical expressions are developed to provide an exact quantification of the impact that drifts have on frequency and active power equilibrium points. In addition, a closed-loop model that accommodates all the policies is derived, and the stability of the equilibrium points is characterized in terms of the clock drifts. Finally, the implementation of the analyzed policies in a laboratory MG provides experimental results that confirm the theoretical analysis., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Secondary switched control with no communications for islanded microgrids

  • Rey, Juan M
  • Martí Colom, Pau|||0000-0002-5189-0782
  • Velasco García, Manel|||0000-0002-0764-3063
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
Flexibility and reliability of AC microgrids are enhanced by reducing the dependence on communications in multi-layer hierarchical control. In this sense, this paper presents a secondary control with no communications for islanded microgrids. It is based on a control scheme that switches between two configurations according to a time-dependent protocol. With this proposal, an excellent performance in terms of transient response and frequency restoration in steady-state is achieved. The paper also presents design considerations for the control parameters. In addition, the theoretical predictions are validated by experimental results from a laboratory microgrid., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Adaptive slope voltage control for distributed generation inverters with improved transient performance

  • Rey López, Juan Manuel
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
  • Guzmán Solà, Ramon|||0000-0002-4386-5800
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Reactive power injection in distributed generation inverters is an useful ancillary service for grid supporting purposes. For grid-feeding converters, the slope control method is the most common voltage regulation strategy used in local (communication-less) applications. Despite its simplicity, this method offers limited dynamic properties in scenarios with changing operation conditions. In this sense, this paper presents an adaptive slope voltage control which provides an improved transient performance against operating variations. To derive the control configuration, a control-oriented mathematical model is developed. The accuracy of the modeling and the performance of the proposed control are validated by selected experimental results., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Control scheme for a multiple-output DC/DC current source parallel resonant converter

  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Guzmán Solà, Ramon|||0000-0002-4386-5800
  • Rey López, Juan Manuel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The aim of this paper is to regulate the output voltages of a multiple-output DC/DC class-D current source parallel resonant converter. To this end, a sliding mode control scheme is presented consisting of an outer voltage loop, an inner current loop and a robust modulator. To devise this control scheme, the averaged large signal model of the converter is derived. In addition, this model is used to determine the stability range of the controller parameters. Some simulation results are provided to validate the expected features of the presented control configuration., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Receding-horizon model predictive control for a three-phase VSI with an LCL filter

  • Guzmán Solà, Ramon|||0000-0002-4386-5800
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Rey, Juan M
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents a Continuous Control Set Model Predictive Control with receding horizon for a threephase voltage source inverter with LCL filter, using a reduced model of the converter. The main advantages of using this reduced model is that an active damping can be achieved while the computational burden is reduced. Besides, in order to eliminate the model uncertainties, and also to achieve a zero steady state error, the proposed converter model includes an embedded integrator. Regarding the control scheme, a Kalman filter is used in order to estimate the three-phase currents without oscillation. The objective is to find the control signals vector that minimizes the error between the current and its reference. It is important to remark that the control signals obtained fromthe cost function can be used directly in a space vector modulator, without the use of additional controllers such as proportionalintegral or proportional-resonant. Compared with the Finite Control Set Model Predictive Control, the proposedmethod operates at fixed switching frequency without using any restriction in the cost function. Simulation and experimental results show that this proposalworks correctly even in case of grid harmonics and voltage sags., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Experimental study of clock drift impact over droop-free distributed control for industrial microgrids

  • Torres Martínez, Javier
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Ghahderijani, Mohammad Moradi
  • Rey López, Juan Manuel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., It is well-know that in systems composed of several digital processors, clock signals of individual units differ from each other due to clock drifts. This paper investigates the effect of clock drifts from voltage source inverters (VSI) in industrial microgrids. Particularly, a primary/secondary droopfree distributed control scheme is considered in order to evaluate its robustness against clock drifts. The study is carried out by fully experimental means using a laboratory microgrid., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Robust and fast sliding-mode control for a DC-DC current-source parallel-resonant converter

  • Moradi Ghahderijani, Mohammad
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Momeneh, Arash
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
Modern DC-DC resonant converters are normally built around a voltage-source series-resonant converter. This study aims to facilitate the practical use of current-source parallel-resonant converters due to their outstanding properties. To this end, this study presents a sliding-mode control scheme, which provides the following features to the closed-loop system: (i) high robustness to external disturbances and parameter variations and (ii) fast transient response during large and abrupt load changes. In addition, a design procedure for determining the values of the control parameters is presented. The theoretical contributions of this study are experimentally validated by selected tests on a laboratory prototype., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Consensus for active power sharing and frequency restoration in islanded microgrids subject to drifting clocks

  • Rosero Chandi, Carlos Xavier
  • Martí Colom, Pau|||0000-0002-5189-0782
  • Velasco García, Manel|||0000-0002-0764-3063
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The application of consensus theory in the control of islanded microgrids (MG) is gaining increased attention because it facilitates the development of distributed control solutions. In particular, its application to active power sharing and frequency regulation has lead to satisfactory results. This paper analyses the effect that local clock drifts have in the parallel operation of voltage source inverters (VSIs) in islanded microgrids (MG) when governed by a distributed consensus algorithm. Analytical expressions that relate the steady-state frequency and active power as a function of each VSI local drift are provided. These expressions allow extracting tuning rules for the consensus-based control algorithm. Simulation results permit corroborating the theoretical analysis., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Voltage support experimental analysis of a low-voltage ride-through strategy applied to grid-connected distributed inverters

  • Garnica López, Miguel Andrés
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
  • Guzmán Solà, Ramon|||0000-0002-4386-5800
In recent decades, different control strategies have been designed for the increasing integration of distributed generation systems. These systems, most of them based on renewable energies, use electronic converters to exchange power with the grid. Capabilities such as low-voltage ride-through and reactive current injection have been experimentally explored and reported in many research papers with a single inverter; however, these capabilities have not been examined in depth in a scenario with multiple inverters connected to the grid. Only few simulation works that include certain methods of reactive power control to solve overvoltage issues in low voltage grids can be found in the literature. Therefore, the overall objective of the work presented in this paper is to provide an experimental analysis of a low-voltage ride-through strategy applied to distributed power generation systems to help support the grid during voltage sags. The amount of reactive power will depend on the capability of each inverter and the amount of generated active power. The obtained experimental results demonstrate that, depending on the configuration of distributed generation, diverse inverters could have different control strategies. In the same way, the discussion of these results shows that the present object of study is of great interest for future research., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Variable structure control in natural frame for three-phase grid-connected inverters with LCL filter

  • Guzmán Solà, Ramon|||0000-0002-4386-5800
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Martín Cañadas, María Elena|||0000-0002-9905-7837
This paper presents a variable structure control in natural frame for a three-phase voltage source inverter. The proposed control method is based on modifying the converter model in natural reference frame, preserving the low frequency state space variables dynamics. Using this model in a Kalman filter, the system state-space variables are estimated allowing to design three robust current sliding-mode controllers in natural frame. The main closed-loop features of the proposed method are: 1) robustness against grid inductance variations because the proposed model is independent of the grid inductance, 2) the power losses are reduced since physical damping resistors are avoided, and 3) the control bandwidth can be increased due to the combination of a variable hysteresis controller with a Kalman filter. To complete the control scheme, a theoretical stability analysis is developed. Finally, selected experimental results validate the proposed control strategy and permit illustrating all its appealing features.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A flexible experimental laboratory for distributed generation networks based on power inverters

  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Guzmán Solà, Ramon|||0000-0002-4386-5800
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
  • Moradi Ghahderijani, Mohammad
In the recently deregulated electricity market, distributed generation based on renewable sources is becoming more and more relevant. In this area, two main distributed scenarios are focusing the attention of recent research: grid-connected mode, where the generation sources are connected to a grid mainly supplied by big power plants, and islanded mode, where the distributed sources, energy storage devices, and loads compose an autonomous entity that in its general form can be named a microgrid. To conduct a successful research in these two scenarios, it is essential to have a flexible experimental setup. This work deals with the description of a real laboratory setup composed of four nodes that can emulate both scenarios of a distributed generation network. A comprehensive description of the hardware and software setup will be done, focusing especially in the dual-core DSP used for control purposes, which is next to the industry standards and able to emulate real complexities. A complete experimental section will show the main features of the system., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Regulatory-framework-embedded energy management system for microgrids: The case study of the Spanish self-consumption scheme

  • Hoz Casas, Jordi de la|||0000-0001-7796-4535
  • Martín Cañadas, María Elena|||0000-0002-9905-7837
  • Alonso, Alex
  • Luna, Adriana Carolina
  • Matas Alcalá, José|||0000-0003-3854-1526
  • Vasquez Quintero, Juan Carlos
  • Guerrero, Josep M.
This paper proposes for the first time to analyse the impact of embedding the regulatory framework constraints inside a model for the energy management optimization of a microgrid. As a case study, a low voltage microgrid using solar energy under the Spanish self-consumption scheme has been selected. The proposed model is based on a previous one elaborated by the authors, which did not include the regulatory framework. The results provided by the former and the new model have been compared, corroborating the importance of taking into account the economic aspects of the regulatory constraints when managing the facility. Furthermore, the results also highlight the urgency to extrapolate this approach to other countries, in order to enhance the economic feasibility of these facilities and aid to their deployment. In addition, the performance of the model has been experimentally validated at the Microgrid Research Laboratory of Aalborg University., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Communication-aware consensus for frequency restoration in islanded microgrids

  • Martí Colom, Pau|||0000-0002-5189-0782
  • Velasco García, Manel|||0000-0002-0764-3063
  • Martín Rull, Enric Xavier|||0000-0002-6775-5470
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
MicroGrids (MGs) include spatially distributed generation (DG) systems and loads that may require operating autonomously in islanded mode. The operation of islanded MGs can benefit from consensus theory and practice, which are the foundations of distributed control. One of the main features of consensus strategies is that they rely on a cooperative scheme where inverters are required to communicate with their neighbors. Therefore properties of the communication network become fundamental. The contribution of this paper is twofold. First, it analyses the impact that communication properties such as transmission interval and message dropouts have in a given consensus-based frequency restoration strategy. Second, new design guidelines for the consensus policy are derived considering the communication dynamics as an opportunity for performance improvement., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Frequency-modulation control of a DC/DC current-source parallel-resonant converter

  • Moradi Ghahderijani, Mohammad
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Momeneh, Arash
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
This paper proposes a frequency-modulation control scheme for a dc/dc current-source parallel-resonant converter with two possible configurations. The basic configuration comprises an external voltage loop, an internal current loop, and a frequency modulator: the voltage loop is responsible for regulating the output voltage, the current loop makes the system controllable and limits the input current, and the modulator provides robustness against variations in resonant component values. The enhanced configuration introduces the output inductor current as a feed-forward term and clearly improves the transient response to fast load changes. The theoretical design of these control schemes is performed systematically by first deriving their small-signal models and second using Bode diagram analysis. The actual performance of the proposed control schemes is experimentally validated by testing on a laboratory prototype., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Voltage sag mitigation in a PV-based industrial microgrid during grid faults

  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Camacho Santiago, Antonio|||0000-0002-0673-6452
  • Torres Martínez, Javier
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The growing interests in industrial microgrid and its high power rating, have made it as a good candidate for voltage support purposes. The aim of this paper is to present a reactive current injection control strategy for a photovoltaic-based industrial microgrid during voltage sags. During the sag, depending on the grid code requirements, the maximum rated reactive current should be injected by the local inverters. The current can be injected through the positive and negative sequences depending on the sag characteristics and power rating of the local inverters. Moreover, to prevent over voltage, the higher phase voltage should be raised to a predefined maximum boundary. Finally, some selected simulation results are presented in order to show the features of the control scheme., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A communication-less control scheme for a variable air-gap wireless energy transfer system using current source resonant converter

  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Rey López, Juan Manuel
  • Torres Martínez, Javier
  • Garnica López, Miguel Andrés
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents a robust control method for wireless energy transfer systems using current source resonant converter without any communication network. The proposed control strategy is valid even for systems with variable air-gap. Output voltage regulation, resonant frequency tracking and zero voltage switching condition are the main control objectives. The control strategy includes a simple modulation technique for the primary side class-D inverter and a sliding mode controller for the secondary-side full-bridge rectifier. Theoretical features of the presented control system are tested by some selected simulation results., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Multi-layer active power and frequency control strategy for industrial microgrids

  • Rey, Juan Manuel
  • Solano, Javier
  • Torres Martínez, Javier
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Industrial microgrids require control strategies that guarantee high reliability and power quality. In this paper a multi-layer active power and frequency control strategy for industrial microgrids is presented. It is composed by a threelayer hierarchical scheme. The first control layer is based on the droop method. The secondary control layer is based on an eventdriven communication scheme that launches a protocol which controls the secondary terms. The tertiary control layer calculates an optimal economical dispatch. The proposed control guarantees an excellent performance in terms of frequency restoration and power sharing. Experimental results obtained on a laboratory microgrid are presented to validate the performance of the proposed control scheme., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Performance evaluation of secondary control policies with respect to digital communications properties in inverter-based islanded microgrids

  • Martí Colom, Pau|||0000-0002-5189-0782
  • Velasco García, Manel|||0000-0002-0764-3063
  • Martín Rull, Enric Xavier|||0000-0002-6775-5470
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
A key challenge for inverted-based microgrids working in islanded mode is to maintain their own frequency and voltage to a certain reference values while regulating the active and reactive power among distributed generators and loads. The implementation of frequency and voltage restoration control policies often requires the use of a digital communication network for real-time data exchange (tertiary control covers the coordi- nated operation of the microgrid and the host grid). Whenever a digital network is placed within the loop, the operation of the secondary control may be affected by the inherent properties of the communication technology. This paper analyses the effect that properties like transmission intervals and message dropouts have for four existing representative approaches to secondary control in a scalable islanded microgrid. The simulated results reveals pros and cons for each approach, and identifies threats that properly avoided or handled in advance can prevent failures that otherwise would occur. Selected experimental results on a low- scale laboratory microgrid corroborate the conclusions extracted from the simulation study., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Control strategy for grid-connected three-phase inverters during voltage sags to meet grid codes and to maximize power delivery capability

  • Garnica López, Miguel Andrés
  • García de Vicuña Muñoz de la Nava, José Luis|||0000-0003-2947-849X
  • Miret Tomàs, Jaume|||0000-0003-1175-4900
  • Castilla Fernández, Miguel|||0000-0002-3284-860X
  • Guzmán Solà, Ramon|||0000-0002-4386-5800
Inverter-based distributed generation plays a vital role in the stability and reliability of new power systems. Under voltage sags, these systems must remain connected to the electrical network according to the stringent requirements of grid codes. Low-voltage ride-through control strategies are becoming a common trend in power electronics research. However, previous studies of these control strategies have not dealt with the different possible scenarios presented by new grid codes, and many of them focus on a very limited number of control objectives. In this study, an algorithm to maximize the converter capabilities was developed and subjected to experimental tests during different voltage sags. In this research, based on unbalanced voltage drops of several severity levels, six different cases of current injection are identified while taking into consideration the restrictions imposed by grid codes. The research results represent a further step towards the development of flexible controllers adaptable to the environments of intelligent electricity grids with high integration of distributed generation., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Experimental study of clock drift impact over droop-free distributed control for industrial microgrids

  • Torres Martínez, Javier
  • Castilla Fernández, Miguel
  • Miret Tomàs, Jaume
  • Ghahderijani, Mohammad Moradi
  • Rey López, Juan Manuel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., It is well-know that in systems composed of several digital processors, clock signals of individual units differ from each other due to clock drifts. This paper investigates the effect of clock drifts from voltage source inverters (VSI) in industrial microgrids. Particularly, a primary/secondary droopfree distributed control scheme is considered in order to evaluate its robustness against clock drifts. The study is carried out by fully experimental means using a laboratory microgrid., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Variable structure control in natural frame for three-phase grid-connected inverters with LCL filter

  • Guzmán Solà, Ramon
  • García de Vicuña Muñoz de la Nava, José Luis
  • Castilla Fernández, Miguel
  • Miret Tomàs, Jaume
  • Martín Cañadas, María Elena
This paper presents a variable structure control in natural frame for a three-phase voltage source inverter. The proposed control method is based on modifying the converter model in natural reference frame, preserving the low frequency state space variables dynamics. Using this model in a Kalman filter, the system state-space variables are estimated allowing to design three robust current sliding-mode controllers in natural frame. The main closed-loop features of the proposed method are: 1) robustness against grid inductance variations because the proposed model is independent of the grid inductance, 2) the power losses are reduced since physical damping resistors are avoided, and 3) the control bandwidth can be increased due to the combination of a variable hysteresis controller with a Kalman filter. To complete the control scheme, a theoretical stability analysis is developed. Finally, selected experimental results validate the proposed control strategy and permit illustrating all its appealing features., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Performance evaluation of secondary control policies with respect to digital communications properties in inverter-based islanded microgrids

  • Martí Colom, Pau
  • Velasco García, Manel
  • Martín Rull, Enric Xavier
  • García de Vicuña Muñoz de la Nava, José Luis
  • Miret Tomàs, Jaume
  • Castilla Fernández, Miguel
A key challenge for inverted-based microgrids working in islanded mode is to maintain their own frequency and voltage to a certain reference values while regulating the active and reactive power among distributed generators and loads. The implementation of frequency and voltage restoration control policies often requires the use of a digital communication network for real-time data exchange (tertiary control covers the coordi- nated operation of the microgrid and the host grid). Whenever a digital network is placed within the loop, the operation of the secondary control may be affected by the inherent properties of the communication technology. This paper analyses the effect that properties like transmission intervals and message dropouts have for four existing representative approaches to secondary control in a scalable islanded microgrid. The simulated results reveals pros and cons for each approach, and identifies threats that properly avoided or handled in advance can prevent failures that otherwise would occur. Selected experimental results on a low- scale laboratory microgrid corroborate the conclusions extracted from the simulation study., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Frequency-modulation control of a DC/DC current-source parallel-resonant converter

  • Moradi Ghahderijani, Mohammad
  • Castilla Fernández, Miguel
  • Momeneh, Arash
  • Miret Tomàs, Jaume
  • García de Vicuña Muñoz de la Nava, José Luis
This paper proposes a frequency-modulation control scheme for a dc/dc current-source parallel-resonant converter with two possible configurations. The basic configuration comprises an external voltage loop, an internal current loop, and a frequency modulator: the voltage loop is responsible for regulating the output voltage, the current loop makes the system controllable and limits the input current, and the modulator provides robustness against variations in resonant component values. The enhanced configuration introduces the output inductor current as a feed-forward term and clearly improves the transient response to fast load changes. The theoretical design of these control schemes is performed systematically by first deriving their small-signal models and second using Bode diagram analysis. The actual performance of the proposed control schemes is experimentally validated by testing on a laboratory prototype., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Analysis of the effect of clock drifts on frequency regulation and power sharing in inverter-based islanded microgrids

  • Martí Colom, Pau
  • Torres Martínez, Javier
  • Rosero Chandi, Carlos Xavier
  • Velasco García, Manel
  • Miret Tomàs, Jaume
  • Castilla Fernández, Miguel
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Local hardware clocks in physically distributed computation devices hardly ever agree because clocks drift apart and the drift can be different for each device. This paper analyses the effect that local clock drifts have in the parallel operation of voltage source inverters (VSIs) in islanded microgrids (MG). The state-of-the-art control policies for frequency regulation and active power sharing in VSIs-based MGs are reviewed and selected prototype policies are then re-formulated in terms of clock drifts. Next, steady-state properties for these policies are analyzed. For each of the policies, analytical expressions are developed to provide an exact quantification of the impact that drifts have on frequency and active power equilibrium points. In addition, a closed-loop model that accommodates all the policies is derived, and the stability of the equilibrium points is characterized in terms of the clock drifts. Finally, the implementation of the analyzed policies in a laboratory MG provides experimental results that confirm the theoretical analysis., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Regulatory-framework-embedded energy management system for microgrids: The case study of the Spanish self-consumption scheme

  • Hoz Casas, Jordi de la
  • Martín Cañadas, María Elena
  • Alonso, Alex
  • Luna, Adriana Carolina
  • Matas Alcalá, José
  • Vasquez Quintero, Juan Carlos
  • Guerrero, Josep M.
This paper proposes for the first time to analyse the impact of embedding the regulatory framework constraints inside a model for the energy management optimization of a microgrid. As a case study, a low voltage microgrid using solar energy under the Spanish self-consumption scheme has been selected. The proposed model is based on a previous one elaborated by the authors, which did not include the regulatory framework. The results provided by the former and the new model have been compared, corroborating the importance of taking into account the economic aspects of the regulatory constraints when managing the facility. Furthermore, the results also highlight the urgency to extrapolate this approach to other countries, in order to enhance the economic feasibility of these facilities and aid to their deployment. In addition, the performance of the model has been experimentally validated at the Microgrid Research Laboratory of Aalborg University., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Voltage support experimental analysis of a low-voltage ride-through strategy applied to grid-connected distributed inverters

  • Garnica López, Miguel Andrés
  • García de Vicuña Muñoz de la Nava, José Luis
  • Miret Tomàs, Jaume
  • Camacho Santiago, Antonio
  • Guzmán Solà, Ramon
In recent decades, different control strategies have been designed for the increasing integration of distributed generation systems. These systems, most of them based on renewable energies, use electronic converters to exchange power with the grid. Capabilities such as low-voltage ride-through and reactive current injection have been experimentally explored and reported in many research papers with a single inverter; however, these capabilities have not been examined in depth in a scenario with multiple inverters connected to the grid. Only few simulation works that include certain methods of reactive power control to solve overvoltage issues in low voltage grids can be found in the literature. Therefore, the overall objective of the work presented in this paper is to provide an experimental analysis of a low-voltage ride-through strategy applied to distributed power generation systems to help support the grid during voltage sags. The amount of reactive power will depend on the capability of each inverter and the amount of generated active power. The obtained experimental results demonstrate that, depending on the configuration of distributed generation, diverse inverters could have different control strategies. In the same way, the discussion of these results shows that the present object of study is of great interest for future research., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Voltage sag mitigation in a PV-based industrial microgrid during grid faults

  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel
  • García de Vicuña Muñoz de la Nava, José Luis
  • Camacho Santiago, Antonio
  • Torres Martínez, Javier
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The growing interests in industrial microgrid and its high power rating, have made it as a good candidate for voltage support purposes. The aim of this paper is to present a reactive current injection control strategy for a photovoltaic-based industrial microgrid during voltage sags. During the sag, depending on the grid code requirements, the maximum rated reactive current should be injected by the local inverters. The current can be injected through the positive and negative sequences depending on the sag characteristics and power rating of the local inverters. Moreover, to prevent over voltage, the higher phase voltage should be raised to a predefined maximum boundary. Finally, some selected simulation results are presented in order to show the features of the control scheme., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Receding-horizon model predictive control for a three-phase VSI with an LCL filter

  • Guzmán Solà, Ramon
  • García de Vicuña Muñoz de la Nava, José Luis
  • Camacho Santiago, Antonio
  • Miret Tomàs, Jaume
  • Rey, Juan M
© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents a Continuous Control Set Model Predictive Control with receding horizon for a threephase voltage source inverter with LCL filter, using a reduced model of the converter. The main advantages of using this reduced model is that an active damping can be achieved while the computational burden is reduced. Besides, in order to eliminate the model uncertainties, and also to achieve a zero steady state error, the proposed converter model includes an embedded integrator. Regarding the control scheme, a Kalman filter is used in order to estimate the three-phase currents without oscillation. The objective is to find the control signals vector that minimizes the error between the current and its reference. It is important to remark that the control signals obtained fromthe cost function can be used directly in a space vector modulator, without the use of additional controllers such as proportionalintegral or proportional-resonant. Compared with the Finite Control Set Model Predictive Control, the proposedmethod operates at fixed switching frequency without using any restriction in the cost function. Simulation and experimental results show that this proposalworks correctly even in case of grid harmonics and voltage sags., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Adaptive slope voltage control for distributed generation inverters with improved transient performance

  • Rey López, Juan Manuel
  • Castilla Fernández, Miguel
  • Miret Tomàs, Jaume
  • Camacho Santiago, Antonio
  • Guzmán Solà, Ramon
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Reactive power injection in distributed generation inverters is an useful ancillary service for grid supporting purposes. For grid-feeding converters, the slope control method is the most common voltage regulation strategy used in local (communication-less) applications. Despite its simplicity, this method offers limited dynamic properties in scenarios with changing operation conditions. In this sense, this paper presents an adaptive slope voltage control which provides an improved transient performance against operating variations. To derive the control configuration, a control-oriented mathematical model is developed. The accuracy of the modeling and the performance of the proposed control are validated by selected experimental results., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A flexible experimental laboratory for distributed generation networks based on power inverters

  • Miret Tomàs, Jaume
  • García de Vicuña Muñoz de la Nava, José Luis
  • Guzmán Solà, Ramon
  • Camacho Santiago, Antonio
  • Moradi Ghahderijani, Mohammad
In the recently deregulated electricity market, distributed generation based on renewable sources is becoming more and more relevant. In this area, two main distributed scenarios are focusing the attention of recent research: grid-connected mode, where the generation sources are connected to a grid mainly supplied by big power plants, and islanded mode, where the distributed sources, energy storage devices, and loads compose an autonomous entity that in its general form can be named a microgrid. To conduct a successful research in these two scenarios, it is essential to have a flexible experimental setup. This work deals with the description of a real laboratory setup composed of four nodes that can emulate both scenarios of a distributed generation network. A comprehensive description of the hardware and software setup will be done, focusing especially in the dual-core DSP used for control purposes, which is next to the industry standards and able to emulate real complexities. A complete experimental section will show the main features of the system., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A communication-less control scheme for a variable air-gap wireless energy transfer system using current source resonant converter

  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel
  • Rey López, Juan Manuel
  • Torres Martínez, Javier
  • Garnica López, Miguel Andrés
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents a robust control method for wireless energy transfer systems using current source resonant converter without any communication network. The proposed control strategy is valid even for systems with variable air-gap. Output voltage regulation, resonant frequency tracking and zero voltage switching condition are the main control objectives. The control strategy includes a simple modulation technique for the primary side class-D inverter and a sliding mode controller for the secondary-side full-bridge rectifier. Theoretical features of the presented control system are tested by some selected simulation results., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Control scheme for a multiple-output DC/DC current source parallel resonant converter

  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel
  • Miret Tomàs, Jaume
  • Guzmán Solà, Ramon
  • Rey López, Juan Manuel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The aim of this paper is to regulate the output voltages of a multiple-output DC/DC class-D current source parallel resonant converter. To this end, a sliding mode control scheme is presented consisting of an outer voltage loop, an inner current loop and a robust modulator. To devise this control scheme, the averaged large signal model of the converter is derived. In addition, this model is used to determine the stability range of the controller parameters. Some simulation results are provided to validate the expected features of the presented control configuration., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Robust and fast sliding-mode control for a DC-DC current-source parallel-resonant converter

  • Moradi Ghahderijani, Mohammad
  • Castilla Fernández, Miguel
  • Momeneh, Arash
  • Miret Tomàs, Jaume
  • García de Vicuña Muñoz de la Nava, José Luis
Modern DC-DC resonant converters are normally built around a voltage-source series-resonant converter. This study aims to facilitate the practical use of current-source parallel-resonant converters due to their outstanding properties. To this end, this study presents a sliding-mode control scheme, which provides the following features to the closed-loop system: (i) high robustness to external disturbances and parameter variations and (ii) fast transient response during large and abrupt load changes. In addition, a design procedure for determining the values of the control parameters is presented. The theoretical contributions of this study are experimentally validated by selected tests on a laboratory prototype., Peer Reviewed, Preprint
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Communication-aware consensus for frequency restoration in islanded microgrids

  • Martí Colom, Pau
  • Velasco García, Manel
  • Martín Rull, Enric Xavier
  • Castilla Fernández, Miguel
  • Miret Tomàs, Jaume
  • Camacho Santiago, Antonio
MicroGrids (MGs) include spatially distributed generation (DG) systems and loads that may require operating autonomously in islanded mode. The operation of islanded MGs can benefit from consensus theory and practice, which are the foundations of distributed control. One of the main features of consensus strategies is that they rely on a cooperative scheme where inverters are required to communicate with their neighbors. Therefore properties of the communication network become fundamental. The contribution of this paper is twofold. First, it analyses the impact that communication properties such as transmission interval and message dropouts have in a given consensus-based frequency restoration strategy. Second, new design guidelines for the consensus policy are derived considering the communication dynamics as an opportunity for performance improvement., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Consensus for active power sharing and frequency restoration in islanded microgrids subject to drifting clocks

  • Rosero Chandi, Carlos Xavier
  • Martí Colom, Pau
  • Velasco García, Manel
  • Castilla Fernández, Miguel
  • Miret Tomàs, Jaume
  • Camacho Santiago, Antonio
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The application of consensus theory in the control of islanded microgrids (MG) is gaining increased attention because it facilitates the development of distributed control solutions. In particular, its application to active power sharing and frequency regulation has lead to satisfactory results. This paper analyses the effect that local clock drifts have in the parallel operation of voltage source inverters (VSIs) in islanded microgrids (MG) when governed by a distributed consensus algorithm. Analytical expressions that relate the steady-state frequency and active power as a function of each VSI local drift are provided. These expressions allow extracting tuning rules for the consensus-based control algorithm. Simulation results permit corroborating the theoretical analysis., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Control strategy for grid-connected three-phase inverters during voltage sags to meet grid codes and to maximize power delivery capability

  • Garnica López, Miguel Andrés
  • García de Vicuña Muñoz de la Nava, José Luis
  • Miret Tomàs, Jaume
  • Castilla Fernández, Miguel
  • Guzmán Solà, Ramon
Inverter-based distributed generation plays a vital role in the stability and reliability of new power systems. Under voltage sags, these systems must remain connected to the electrical network according to the stringent requirements of grid codes. Low-voltage ride-through control strategies are becoming a common trend in power electronics research. However, previous studies of these control strategies have not dealt with the different possible scenarios presented by new grid codes, and many of them focus on a very limited number of control objectives. In this study, an algorithm to maximize the converter capabilities was developed and subjected to experimental tests during different voltage sags. In this research, based on unbalanced voltage drops of several severity levels, six different cases of current injection are identified while taking into consideration the restrictions imposed by grid codes. The research results represent a further step towards the development of flexible controllers adaptable to the environments of intelligent electricity grids with high integration of distributed generation., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Secondary switched control with no communications for islanded microgrids

  • Rey, Juan M
  • Martí Colom, Pau
  • Velasco García, Manel
  • Miret Tomàs, Jaume
  • Castilla Fernández, Miguel
Flexibility and reliability of AC microgrids are enhanced by reducing the dependence on communications in multi-layer hierarchical control. In this sense, this paper presents a secondary control with no communications for islanded microgrids. It is based on a control scheme that switches between two configurations according to a time-dependent protocol. With this proposal, an excellent performance in terms of transient response and frequency restoration in steady-state is achieved. The paper also presents design considerations for the control parameters. In addition, the theoretical predictions are validated by experimental results from a laboratory microgrid., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Multi-layer active power and frequency control strategy for industrial microgrids

  • Rey, Juan Manuel
  • Solano, Javier
  • Torres Martínez, Javier
  • Miret Tomàs, Jaume
  • Ghahderijani, Mohammad Moradi
  • Castilla Fernández, Miguel
© 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Industrial microgrids require control strategies that guarantee high reliability and power quality. In this paper a multi-layer active power and frequency control strategy for industrial microgrids is presented. It is composed by a threelayer hierarchical scheme. The first control layer is based on the droop method. The secondary control layer is based on an eventdriven communication scheme that launches a protocol which controls the secondary terms. The tertiary control layer calculates an optimal economical dispatch. The proposed control guarantees an excellent performance in terms of frequency restoration and power sharing. Experimental results obtained on a laboratory microgrid are presented to validate the performance of the proposed control scheme., Peer Reviewed, Postprint (author's final draft)