Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Three-dimensional fractal geometry for gas permeation in microchannels

  • Malankowska, M.
  • Schlautmann, S.
  • Berenschot, E.J.W.
  • Tiggelaar, R.M.
  • Pina, M.P.
  • Mallada, R.
  • Tas, N.R.
  • Gardeniers, H.
The novel concept of a microfluidic chip with an integrated three-dimensional fractal geometry with nanopores, acting as a gas transport membrane, is presented. The method of engineering the 3D fractal structure is based on a combination of anisotropic etching of silicon and corner lithography. The permeation of oxygen and carbon dioxide through the fractal membrane is measured and validated theoretically. The results show high permeation flux due to low resistance to mass transfer because of the hierarchical branched structure of the fractals, and the high number of the apertures. This approach offers an advantage of high surface to volume ratio and pores in the range of nanometers. The obtained results show that the gas permeation through the nanonozzles in the form of fractal geometry is remarkably enhanced in comparison to the commonly-used polydimethylsiloxane (PDMS) dense membrane. The developed chip is envisioned as an interesting alternative for gas-liquid contactors that require harsh conditions, such as microreactors or microdevices, for energy applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Study of different titanosilicate (TS-1 and ETS-10) as fillers for Mixed Matrix Membranes for CO2/CH4 gas separation applications

  • Martin-Gil, V.
  • Lopez, A.
  • Hrabanek, P.
  • Mallada, R.
  • Vankelecom, I.F.J.
  • Fila, V.
Three titanosilicate zeolites were used as fillers for Mixed Matrix Membranes: (i) ETS-10, TS-1 having Si/Ti=100 and (iii) TS-1 using Si/Ti=25. Zeolite samples were characterized by X-Ray Diffraction, Scanning Electron Microscopy, Atomic Emission Spectroscopy, X-Ray Photoelectron Spectroscopy, and CO2 and CH4 adsorption isotherms. TS-1 particles showed a narrow size distribution ranging from 200 nm to 400 nm. In the case of ETS-10, the size distribution was broader ranging from 400 nm to 800 nm. Mixed Matrix Membranes were prepared using Matrimid (R) polyimide as continuous phase and filler loadings of 10, 20, and 30 wt%. Membranes were characterized by Thermogravimetric Analysis, Differential Scanning Calorimetry, and Scanning Electron Microscopy. The performances was measured at 8 bars of transmembrane pressure for CO2/CH4 mixed gases system at 50/50 vol/vol. concentration. Membranes using TS-1 (Si/Ti=25) as filler showed a maximum increase of 89.1% of CO2 permeability and 23.9% increase in separation factor. In the case of TS-1 (Si/Ti=100) only permeability increased significantly, with a maximum increase of 90.1%. Regarding the ETS-10 membranes, both permeability and separation factor increased slightly with respect to the reference polymeric membrane (22.5% in CO2 permeability and 7.8% in the separation factor). In conclusion, TS-1 (Si/Ti=25) is the most suitable filler for the use in Mixed Matrix Membranes for gas separation applications among the titanosilicate studied in this work.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Exploring the Gas-Permeation Properties of Proton-Conducting Membranes Based on Protic Imidazolium Ionic Liquids: Application in Natural Gas Processing

  • Kallem, P.
  • Charmette, C.
  • Drobek, M.
  • Julbe, A.
  • Mallada, R.
  • Pina, M.P.
This experimental study explores the potential of supported ionic liquid membranes (SILMs) based on protic imidazolium ionic liquids (ILs) and randomly nanoporous polybenzimidazole (PBI) supports for CH4/N-2 separation. In particular, three classes of SILMs have been prepared by the infiltration of porous PBI membranes with different protic moieties: 1-H-3-methylimidazolium bis (trifluoromethane sulfonyl)imide; 1-H-3-vinylimidazolium bis(trifluoromethane sulfonyl)imide followed by in situ ultraviolet (UV) polymerization to poly[1-(3H-imidazolium)ethylene] bis(trifluoromethanesulfonyl)imide. The polymerization process has been monitored by Fourier transform infrared (FTIR) spectroscopy and the concentration of the protic entities in the SILMs has been evaluated by thermogravimetric analysis (TGA). Single gas permeability values of N-2 and CH4 at 313 K, 333 K and 363 K were obtained from a series of experiments conducted in a batch gas permeance system. The results obtained were assessed in terms of the preferential cavity formation and favorable solvation of methane in the apolar domains of the protic ionic network. The most attractive behavior exhibited poly[1-(3H-imidazolium)ethylene]bis(trifluoromethanesulfonyl)imide polymeric ionic liquid (PIL) cross-linked with 1% divinylbenzene supported membranes, showing stable performance when increasing the upstream pressure. The CH4/N-2 permselectivity value of 2.1 with CH4 permeability of 156 Barrer at 363 K suggests that the transport mechanism of the as-prepared SILMs is solubility-dominated.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hierarchical Porous Polybenzimidazole Microsieves: An Efficient Architecture for Anhydrous Proton Transport via Polyionic Liquids

  • Kallem, P.
  • Drobek, M.
  • Julbe, A.
  • Vriezekolk, E.J.
  • Mallada, R.
  • Pina, M.P.
Liquid-induced phase-separation micromolding (LIPSµM) has been successfully used for manufacturing hierarchical porous polybenzimidazole (HPBI) microsieves (42-46% porosity, 30-40 µm thick) with a specific pore architecture (pattern of macropores: ~9 µm in size, perforated, dispersed in a porous matrix with a 50-100 nm pore size). Using these microsieves, proton-exchange membranes were fabricated by the infiltration of a 1H-3-vinylimidazolium bis(trifluoromethanesulfonyl)imide liquid and divinylbenzene (as a cross-linker), followed by in situ UV polymerization. Our approach relies on the separation of the ion conducting function from the structural support function. Thus, the polymeric ionic liquid (PIL) moiety plays the role of a proton conductor, whereas the HPBI microsieve ensures the mechanical resistance of the system. The influence of the porous support architecture on both proton transport performance and mechanical strength has been specifically investigated by means of comparison with straight macroporous (36% porosity) and randomly nanoporous (68% porosity) PBI counterparts. The most attractive results were obtained with the poly[1-(3H-imidazolium)ethylene]bis(trifluoromethanesulfonyl)imide PIL cross-linked with 1% divinylbenzene supported on HPBI membranes with a 21-µm-thick skin layer, achieving conductivity values up to 85 mS cm-1 at 200 °C under anhydrous conditions and in the absence of mineral acids.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microfluidic devices as gas – Ionic liquid membrane contactors for CO2 removal from anaesthesia gases

  • Malankowska, M.
  • Martins, C. F.
  • Rho, H. S.
  • Neves, L. A.
  • Tiggelaar, R. M.
  • Crespo, J. G.
  • Pina, M. P.
  • Mallada, R.
  • Gardeniers, H.
  • Coelhoso, I. M.
This work proposes a microfluidic gas – ionic liquid contactor for CO2 removal from anaesthesia gas, containing Xe. The working principle involves the transport of CO2 through a polymer flat membrane followed by its capture and enzymatic bioconversion in the ionic liquid solvent. Microfluidic devices enable a rapid and inexpensive screening of potential CO2 absorbers. The alveolar – type design of the ionic liquid chamber was adopted to reduce mass transfer limitations of CO2 through the liquid phase. Polydimethylsiloxane (PDMS) was the chosen polymer for dense membrane, as well as for the microfluidic device fabrication, mainly due to the high permeability of gases, O2 and CO2, and low cost. The selected ionic liquid was cholinium propionate (CP) with a water activity of 0.753, due to its high affinity towards CO2 and biocompatibility with the enzyme used for CO2 conversion to bicarbonate, carbonic anhydrase (CA). The CO2 and Xe permeability and CO2/Xe selectivity were determined in the microfluidic devices developed and compared to those exhibited by free standing PDMS membranes mounted on a standard permeation cell. The performance of the microfluidic devices as gas – ionic liquid contactors was evaluated for a given solvent flow rate with pure gas streams of CO2 and Xe. The obtained results show that cholinium propionate with or without the enzyme has no effect on the Xe transport, but remarkably enhances the affinity towards carbon dioxide leading to enhancement factor up to 1.9 in the presence of 0.1 mg CA/gIL.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Understanding blood oxygenation in a microfluidic meander double side membrane contactor

  • Malankowska, M.
  • Julian, I.
  • Pellejero, I.
  • Rho, H.S.
  • Schlautmann, S.
  • Tiggelaar, R.M.
  • Pina, M.P.
  • Gardeniers, H.J.G.E.
  • Mallada, R.
Lung disease is one of the most important causes of high morbidity in preterm infants. In this work, we study a simple and easy to fabricate microfluidic device that demonstrates a great potential for blood oxygenation. A meander type architecture with double side vertical membrane arrangement has been selected as reference model to investigate the oxygenation process. The design criteria for the fabricated devices has been to maximize the oxygen saturation level while ensuring the physiological blood flow in order to avoid thrombus formation and channel blockage during operation. A mathematical model for the oxygen transfer has been developed and validated by the experimental study. The obtained results demonstrate that blood was successfully oxygenated up to approximately 98% of O2 saturation and that the oxygen transfer rate at 1 mL/min blood flow rate was approximately 92 mL/min·m2. Finally, a sensitivity analysis of the key parameters, i.e. size of the channel, oxygen concentration in the gas phase and oxygen permeation properties of the membrane, is carried out to discuss the performance limits and to settle the guidelines for future developments.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Experimental evaluation of the thermal polarization in direct contact membrane distillation using electrospun nanofiber membranes doped with molecular probes

  • Santoro, S.
  • Vidorreta, I.
  • Coelhoso, I.
  • Lima, J.C.
  • Desiderio, G.
  • Lombardo, G.
  • Drioli, E.
  • Mallada, R.
  • Crespo, J.
  • Criscuoli, A.
  • Figoli, A.
Membrane distillation (MD) has recently gained considerable attention as a valid process for the production of fresh-water due to its ability to exploit low grade waste heat for operation and to ensure a nearly feed concentration-independent production of high-purity distillate. Limitations have been related to polarization phenomena negatively affecting the thermal efficiency of the process and, as a consequence, its productivity. Several theoretical models have been developed to predict the impact of the operating conditions of the process on the thermal polarization, but there is a lack of experimental validation. In this study, electrospun nanofiber membranes (ENMs) made of Poly(vinylidene fluoride) (PVDF) and doped with (1, 10-phenanthroline) ruthenium (II) Ru(phen) 3 were tested at different operating conditions (i.e., temperature and velocity of the feed) in direct contact membrane distillation (DCMD). The temperature sensitive luminophore, Ru(phen) 3 , allowed the on-line and non-invasive mapping of the temperature at the membrane surface during the process and the experimental evaluation of the effect of the temperature and velocity of the feed on the thermal polarization.