Pasar al contenido principal

OSCILADORES FLUIDICOS: NUEVAS PERSPECTIVAS Y APLICACION AL CONTROL ACTIVO DE FLUJO

FIS2016-77849-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Towards a better understanding of wall-driven square cavity flows using the Lattice Boltzmann method

  • An, Bo
  • Mellibovsky Elstein, Fernando
  • Bergadà Granyó, Josep Maria
  • Sang, WM
Wall-driven flow in square cavities has been studied extensively, yet it appears some main flow characteristics have not been fully investigated. Previous research on the classic lid-driven cavity (S1) flow has produced the critical Reynolds numbers separating the laminar steady and unsteady flows. Wall-driven cavities with two opposing walls moving at the same speed and the same (S2p) or opposite (S2a) directions have seldom been studied in the literature and no critical Reynolds numbers characterizing transitional flows have ever been investigated. After validating the LBM code for the three configurations studied, extensive numerical simulations have been undertaken to provide approximate ranges for the critical Hopf and Neimark-Sacker bifurcations for the classic and two two-sided cavity configurations. The threshold for transition to chaotic motion is also reported. The symmetries of the solutions are monitored across the various bifurcations for the two-sided wall driven cavities. The mirror-symmetry of the base solution for case S2p is lost at the Hopf bifurcation. The exact same scenario occurs with the pi-rotational symmetry of the base state for case S2a., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fluidic oscillators, the effect of some design modifications

  • Baghaei, Masoud
  • Bergadà Granyó, Josep Maria
The number of applications where fluidic oscillators are expected to be used in the future, is raising sharply, then their ability of interacting with the boundary layer to modify forces on bluff bodies, enhancing heat transfer or decreasing noise generation, are just few of the applications where fluidic oscillators can be used. For each application a particular pulsating frequency and amplitude are required to minimize/maximize the variable under study, force, Nusselt number, etc. For a given range of Reynolds numbers, fluidic oscillators present a linear relationship between the output frequency and the incoming fluid flow, yet it appears the modification of the internal fluidic oscillator geometry may affect this relation. In the present paper and for a given fluidic oscillator, several performance parameters will be numerically evaluated as a function of different internal modifications via using 3D-CFD simulations. The paper is also evaluating the relation between the momentum applied to the mixing chamber incoming jet and the oscillator output characteristics. The evaluation is based on studying the output mass flow frequency and amplitude whenever several internal geometry parameters are modified. The geometry modifications considered were: the mixing chamber inlet and outlet widths, and the mixing chamber inlet and outlet wall inclination angles. The concept behind this paper is, to evaluate how much the fluidic oscillator internal dimensions affect the device main characteristics, and to analyze which parts of the oscillator produce a higher impact on the fluidic oscillator output characteristics. For the different internal modifications evaluated, special care is taken in studying the forces required to flip the jet. The entire study is performed for three different Reynolds numbers, 8711, 16034 and 32068. Among the conclusions reached it is to be highlighted that, for a given Reynolds number, modifying the internal shape affects the oscillation frequencies and amplitudes. Any oscillator internal modification generates a much relevant effect as Reynolds number increases. Under all conditions studied, it was observed the fluidic oscillator is pressure driven., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Parametric analysis of the flow past a square cylinder in the interface of two different-velocity streams, Anàlisi parametric del fluxe al voltant de un quadrat posat en mig de dos fluids amb velocitats diferents

  • Elmansy, Reda Mohamed Yousyf Abdallah
  • Bergadà Granyó, Josep Maria
  • Sarwar, Wasim
  • Mellibovsky Elstein, Fernando
We address the linear stability of the two-dimensional incompressible flow past a square cylinder immersed in the wake of an upstream splitter plate, which separates two streams of different velocities, UT (top) and UB (bottom), to three-dimensional perturbations. The analysis is done in the so-called wake transition regime, across which two-dimensional vortex shedding incorporates spanwise modulation. In addition to the top and bottom stream Reynolds numbers (ReT,B=DUT,B/¿, with D the square cylinder side and ¿ the kinematic viscosity of the fluid), a parametric analysis is conducted to gauge the effects of splitter plate length (S) and the gap between the trailing edge of the splitter plate and the front face of the cylinder (G) on the leading three-dimensionalizing instabilities. Modes akin to the A- and B-type instabilities that characterize the wake transition regime past circular and square cylinders in homogeneous incoming flow are observed only at very small values of the top-to-bottom Reynolds number ratio R=ReT/ReB, while a third mode, mode C, is ubiquitous beyond more than very mild values of R. Increasing S at constant small G has a stabilizing effect on mode C, whose onset is pushed to higher values of R. Only for long S is mode A observed. Fixing a short S and increasing G results instead in a destabilization of mode C, and mode B is favored over mode A., This work was supported by the Spanish Government (Grant Nos. FIS2016-77849-R and PID2020-114043GB-I00) and by the Catalan Government (Grant No. 2017-SGR-00785). Part of the computations was done in the Red Española de Supercomputación (RES), Spanish supercomputing network (Grant Nos. FI-2019-1-0023 and FI-2018-3-0030). F. Mellibovsky is a Serra-Húnter fellow., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Numerical investigation on the flow around a square cylinder with an upstream splitter plate at low Reynolds numbers

  • An, Bo
  • Bergadà Granyó, Josep Maria
  • Mellibovsky Elstein, Fernando
  • Sang, W.M.
  • Xi, C.
The present study focuses on the flow over a 2D square cylinder with a plate placed in front of it. An in-house code using the lattice Boltzmann method was employed for all the simulations presented. Few cases were simulated using the open source code Nektar++, the results obtained from both methodologies were compared. Regarding the plate, three related parameters, velocity ratio, distance between the plate and cylinder and the thickness of the plate, were studied in order to evaluate the impact of these parameters on the flow behavior. The interactions between these parameters were as well investigated. The effect of these parameters on flow transitional properties such as Hopf and Neimark–Sacker bifurcations were discussed. Whenever the velocity ratio exceeds a certain value, Kelvin–Helmholtz instabilities dominate the vortex shedding. As velocity ratio increases, drag coefficient and vortex shedding frequency increase. The POD method was employed to predict the flow behavior based on the existing information. It turned out the POD method is a trustable methodology to mathematically pre-investigate the flow field, therefore it is capable of saving large computational resources, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Large eddy simulation of optimal synthetic jet actuation on a SD7003 airfoil in post-stall conditions

  • Monshi Tousi, Navid
  • Bergadà Granyó, Josep Maria
  • Mellibovsky Elstein, Fernando
Aerodynamic performances may be optimised by the appropriate tuning of Active Flow Control (AFC) parameters. For the first time, we couple Genetic Algorithms (GA) with an unsteady Reynolds-Averaged Navier-Stokes (RANS) solver using the Spalart-Allmaras (SA) turbulence model to maximise lift and aerodynamic efficiency of an airfoil in stall conditions [1], and then validate the resulting set of optimal Synthetic Jet Actuator (SJA) parameters against well-resolved three-dimensional Large Eddy Simulation (LES). The airfoil considered is the SD7003, at the Reynolds number and the post-stall angle of attack . We find that, although SA-RANS is not quite as accurate as LES, it can still predict macroscopic aggregates such as lift and drag coefficients, provided the free-stream turbulence is prescribed to reasonable values. The sensitivity to free-stream turbulence is found to be particularly critical for SJA cases. Baseline LES simulation agrees well with literature results, while RANS-SA would seem to remain a valid model to a certain degree. For optimally actuated cases, our LES simulation predicts far better performances than obtained by suboptimal SJA LES computations as reported by other authors [2] for the same airfoil, Re and a, which illustrates the applicability and effectiveness of the SJA optimisation technique applied, despite using the less accurate yet computationally faster SA-RANS. The flow topology and wake dynamics of baseline and SJA cases are thoroughly compared to elucidate the mechanism whereby aerodynamic performances are enhanced, This work was supported by the Spanish Government under grants FIS2016-77849-R and PID2020-114043GB-I00 and by the Catalan Government under grant 2017-SGR-00785. Computations were performed in the Red Española de Supercomputación (RES), Spanish supercomputer network, under the grants IM-2019-3-0002 and IM-2020-1-0001. F. M. is a Serra-Húnter fellow, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Square cavity flow driven by two mutually facing sliding walls

  • An, Bo
  • Bergadà Granyó, Josep Maria
  • Sang, Weimin
  • Li, Dong
  • Mellibovsky Elstein, Fernando
We investigate the flow inside a 2D square cavity driven by the motion of two mutually facing walls independently sliding at different speeds. The exploration, which employs the lattice Boltzmann method (LBM), extends on previous studies that had the two lids moving with the exact same speed in opposite directions. Unlike there, here the flow is governed by two Reynolds numbers (ReT, ReB) associated to the velocities of the two moving walls. For convenience, we define a bulk Reynolds number Re and quantify the driving velocity asymmetry by a parameter a. Parameter a has been defined in the range a¿[-p/4, 0] and a systematic sweep in Reynolds numbers has been undertaken to unfold the transitional dynamics path of the two-sided wall-driven cavity flow. In particular, the critical Reynolds numbers for Hopf and Neimark-Sacker bifurcations have been determined as a function of a. The eventual advent of chaotic dynamics and the symmetry properties of the intervening solutions are also analyzed and discussed. The study unfolds for the first time the full bifurcation scenario as a function of the two Reynolds numbers, and reveals the different flow topologies found along the transitional path, This work is supported by the projects of the North‐ western Polytechnical University (No. G2021KY05103), the Natioanl Key Laboratory of Science and Technology on Aero‐ dynamic Design and Research (No. 614220121030101), the Key Laboratory of Icing and Anti/De-icing of China Aerodynamics Research and Development Center (No. IADL20210302), the Spanish Government (Nos. FIS 2016-77849-R and PID2020- 114043GB-I00), the Catalan Government (No. 2017-2017-SGR00785), and the Barcelona Supercomputing Centre (Nos. FI2017-2-002, FI-2017-3-0009, and FI-2016-3-0038), Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the flow and passive noise control of an open cavity at Re=5000

  • Martín Navarrete, Rocío
  • Soria Guerrero, Manel
  • Rodríguez Pérez, Ivette María
  • Lehmkuhl Barba, Oriol
The interaction of turbulent flows with the external structure of ground vehicles generates uncomfortable noise and a lot of attention is devoted to find new mechanisms for its suppression. The present work is concerned with open cavity flows, very often found in the automotive industry. A three-dimensional rectangular very wide open cavity with aspect ratio L/D=4 at Reynolds number ReD=5000 and Mach number M=0.1 is considered. The passive control technique is based on eight different geometrical modifications: the length of the cavity, the radius of the trailing, leading and bottom edges and the difference in heights between the left and right wall of the cavity. Wall-resolved Large Eddy Simulations (LES) are used to obtain the flow fields and a post-process based on Curle’s analogy is applied to evaluate the acoustic radiation and the effectiveness of the control mechanisms. The results show that the modifications on the trailing edge are the most effective to control the flow. They allow to reduce the pressure fluctuations produced by the recirculation confined inside the cavity and the abrupt ejection of the flow at the trailing edge. As a consequence, the overall sound pressure level can be decreased up to 9 dB., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Aerodynamic performances and wake topology past a square cylinder in the interface of two different-velocity streams

  • El Mansy, Reda
  • Bergadà Granyó, Josep Maria
  • Sarwar, Wasim
  • Mellibovsky Elstein, Fernando
We analyze the incompressible flow past a square cylinder immersed in the wake of an upstream splitter plate, which separates two streams of different velocities, UT (top) and UB (bottom). The Reynolds number associated with the flow below the plate is kept constant at ¿¿¿=¿¿¿/¿=56, based on the square cylinder side D as characteristic length. The top-to-bottom flow dissymmetry is measured by the ratio ¿=¿¿¿/¿¿¿¿[1,5.3] between the Reynolds numbers above and below the plate. The equivalent bulk Reynolds taken as the mean between top and bottom changes with R in the range ¿¿=(¿¿¿+¿¿¿)/2¿[56,178]. A Hopf bifurcation occurs at ¿=2.1±0.1 (¿¿=86.8±2.8), which results in an asymmetric Kármán vortex street with vortices only showing on the high-velocity side of the wake. A spanwise modulational instability is responsible for the three-dimensionalization of the flow at ¿¿3.1 (¿¿¿115) with the associated wavelength of ¿¿¿2.4. For velocity ratios ¿=4, the flow becomes spatiotemporally chaotic. The migration of the mean stagnation and base pressure points on the front and rear surfaces of the cylinder as R is increased determine the boundary layer properties on the top and bottom surfaces and, with them, the shear layers that roll up into the formation of Kármán vortices, which in turn help to clarify the evolution of the lift and drag coefficients. The symmetries of the different solutions across the flow transition regime are imprinted on the top and bottom boundary layers and can, therefore, be analyzed from the time evolution and spanwise distribution of trailing edge boundary layer displacement thickness at the top and bottom rear corners, This work was supported by the Spanish Government under Grant Nos. FIS2016-77849-R and PID2020-114043GB-I00 and by the Catalan Government under Grant No. 2017-SGR-00785. Part of the computations were done in the Red Española de Supercomputación (RES), Spanish supercomputing network, under Grant Nos. FI-2019-1-0023 and FI-2018-3-0030. F. Mellibovsky is a Serra-Húnter fellow, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Transition to periodic behaviour of flow past a circular cylinder under the action of fluidic actuation in the transitional regime

  • Sarwar, Wasim
  • Mellibovsky Elstein, Fernando
  • Alam, Mahbub
  • Zafar, Farhan
This study focuses on the numerical investigation of the underlying mechanism of transition from chaotic to periodic dynamics of circular cylinder wake under the action of time-dependent fluidic actuation at the Reynolds number = 2000. The forcing is realized by blowing and suction from the slits located at ±90° on the top and bottom surfaces of the cylinder. The inverse period-doubling cascade is the underlying physical mechanism underpinning the wake transition from mild chaos to perfectly periodic dynamics in the spanwise-independent, time-dependent forcing at twice the natural vortex-shedding frequency., This work has been financed by the Spanish and Catalan Governments under grants FIS2016-77849-R and 2017-SGR-00785, respectively. The authors also thankfully acknowledge the computer resources at MareNostrum and Calendula accessed through grants RES-FI-2017-2-0020 and RES-FI-2017-3-0009, respectively, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Flow topology and heat transfer analysis of slotted and axisymmetric synthetic impinging jets

  • Miró Jané, Arnau
  • Soria Guerrero, Manel
  • Cajas García, Juan Carlos
  • Rodríguez Pérez, Ivette María
  • Moulinec, Charles
This work is focused on exploring the flow and heat transfer capabilities for slotted and axisymmetric cavity configurations for synthetic impinging jets; the jet is enclosed between two isothermal parallel plates, impinging into the top hot plate. Numerical simulations using the Arbitrary Lagrangian-Eulerian formulation of the Navier-Stokes equations are performed for Reynolds numbers of 50\rii{, 300} and 500 and a jet formation criteria of 3. The pattern of the flow from both configurations differ, which result in different impinging behaviors. The slotted jet is wider than the axisymmetric one, showing an increased turbulent mixing and a lower velocity deficit. On the other hand, the narrower jet of the axisymmetric configuration results in less mixing and more penetration, with a higher velocity deficit. This leads to a higher heat transfer peak in the axisymmetric configuration with a faster decay when moving away from the jet centerline than observed for the slotted configuration., This work has been partially supported by the Spanish Ministry (MEC) project FIS2016-77849-R. We also acknowledge Red Española de Surpercomputación (RES) for awarding us access to the MareNostrum IV machine based in Barcelona, Spain (Ref. FI-2016-3-0014 and FI- 2017-2- 0017) and the HPC-EUROPA3 (INFRAIA-2016-1-730897), with the support of the EC Research Innovation Action under the H2020 Pro-gramme; which awarded access to the ARCHER UK National Supercomputing Service (http://www.archer.ac.uk). The authors also would like to thank the EPSRC UK Turbulence Consortium (EP/R029326/1) for its support. The research reported in this work was also partially supported by OGS and CINECA under HPC-TRES program award number 2018–02, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Active flow control optimisation on SD7003 airfoil at pre and post-stall angles of attack using synthetic jets

  • Monshi Tousi, Navid
  • Coma Company, Martí
  • Bergadà Granyó, Josep Maria
  • Pons Prats, Jordi
  • Mellibovsky Elstein, Fernando
  • Bugeda Castelltort, Gabriel
The use of Active Flow Control (AFC) technologies to modify the forces acting on streamlined bodies is one of the most active research fields in aerodynamics. For each particular application, finding the optimum set of AFC parameters which maximises lift, minimises drag or maximises lift-to-drag ratio (aerodynamic efficiency), has become a necessary design requirement. In the present paper, the AFC technology was applied to the Selig-Donovan 7003 (SD7003) airfoil at Reynolds number 6 × 104. Synthetic jets were employed to modify the lift and drag forces acting on the airfoil. Four angles of attack (AoA) of 4¿, 6¿, 8¿ and 14¿ were considered, alongside five AFC parameters: jet position, jet width, momentum coefficient, forcing frequency and jet inclination angle. A multi objective optimisation based on genetic algorithms (GA) was performed for each angle of attack to find the optimum combination of AFC parameters. Each GA generation was simulated using Computational Fluid Dynamics (CFD). A home-made GA package was linked with a mesh generator and the CFD solver, and the results were automatically fed back to the GA code. Over 2200 CFD simulations were performed in two dimensions, using the SpalartAllmaras turbulent model. The motivation behind the current study is to understand the dependence of the optimum set of AFC parameters on the AoA. Results show that, as AoA is increased, the potential benefits of AFC become more pronounced, which allows for considerable improvement in aerodynamic efficiency. The physics involved in the interaction between the main flow and synthetic jet are clearly presented and clarifies that the physical phenomenon to obtain maximum efficiency is completely different at pre-stall and post-stall AoA. In particular, the aerodynamic efficiency was increased by 251% from baseline (no actuation) by using a moderate/finite momentum coefficient at AoA=14¿, while a mere 39% increase was obtained at AoA=8¿. In addition, the interaction between the incoming flow and the synthetic jet pulsating flow at different injection angles has been thoroughly investigated, This work was supported by the Spanish and Catalan Governments under grants FIS2016-77849-R and 2017-SGR-00785, respectively. Part of the computations were done in the Red Española de Supercomputación (RES), Spanish supercomputer network, under the grants IM-2019-3-0002 and IM-2020-1-0001. Dr. Jordi Pons-Prats acknowledges the support of the Serra Hunter programme by the Catalan Government, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Analysis of the forces driving the oscillations in 3D fluidic oscillators

  • Baghaei, Masoud
  • Bergadà Granyó, Josep Maria
One of the main advantages of fluidic oscillators is that they do not have moving parts, which brings high reliability whenever being used in real applications. To use these devices in real applications, it is necessary to evaluate their performance, since each application requires a particular injected fluid momentum and frequency. In this paper, the performance of a given fluidic oscillator is evaluated at different Reynolds numbers via a 3D-computational fluid dynamics (CFD) analysis. The net momentum applied to the incoming jet is compared with the dynamic maximum stagnation pressure in the mixing chamber, to the dynamic output mass flow, to the dynamic feedback channels mass flow, to the pressure acting to both feedback channels outlets, and to the mixing chamber inlet jet oscillation angle. A perfect correlation between these parameters is obtained, therefore indicating the oscillation is triggered by the pressure momentum term applied to the jet at the feedback channels outlets. The paper proves that the stagnation pressure fluctuations appearing at the mixing chamber inclined walls are responsible for the pressure momentum term acting at the feedback channels outlets. Until now it was thought that the oscillations were driven by the mass flow flowing along the feedback channels, however in this paper it is proved that the oscillations are pressure driven. The peak to peak stagnation pressure fluctuations increase with increasing Reynolds number, and so does the pressure momentum term acting onto the mixing chamber inlet incoming jet, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Onset of temporal dynamics within a low reynolds-number laminar fluidic oscillator

  • Sarwar, Wasim
  • Bergadà Granyó, Josep Maria
  • Mellibovsky Elstein, Fernando
We investigate the onset of temporal dynamics of a fluidic oscillator (FO) in the laminar regime at very low Reynolds number ( where and are the velocity and channel height at inlet, and is the kinematic viscosity of the fluid). Both two- and spanwise-periodic-three-dimensional simulations are performed using high-order spectral element methods to characterise the flow inside the FO cavity and the outcoming jet. While the flow remains steady and symmetric for sufficiently low the two-dimensional FO undergoes a symmetry-breaking Hopf bifurcation at that results in a space-time symmetric periodic solution. The remnant space-time symmetry is later broken in a pitchfork bifurcation of limit cycles at . Taking three-dimensionality into consideration results in an early spanwise-invariance disruption at about of wavelength that retards the onset of the oscillation to . This effect is little representative of actual FO implementations, which are typically much narrower than the wavelength of the spanwise instability observed at these low . Contrary to what happens with FOs in the turbulent oscillatory regime, the oscillation frequency of the output jet in the laminar regime is found to decrease with . The mechanism that drives the oscillation, however, remains the same: as the high speed flow inside the cavity attaches to one of the internal walls through the Coanda effect, the feedback channels divert part of the momentum back, which pushes the incoming flow against the opposite wall. The alternate deviation of the flow inside the cavity to one or the other side results in the periodic flipping of the output jet. The pressure contribution to net momentum at the end of the feedback channels is found to be double that of the advective momentum flux at the early time-periodic regime but both become comparable as is increased. The jet sweeping angle amplitude is more pronounced for the two-dimensional FO as compared to three-dimensional at a fixed given the Coanda effect being only partially fulfilled in the latter case. In both cases the sweep amplitude increases with . The instability of the output jet, which becomes slightly chaotic already at very low is responsible for triggering the cavity instability that drives the oscillation slightly earlier than it would, should outside noise be suppressed altogether, This work has been financed by the Spanish and Catalan Governments under grants FIS2016-77849-R and 2017-SGR00785, respectively. The authors also thankfully acknowledge the computer resources at MareNostrum and Calendula accessed through grants RES-FI-2017-2-0020 and RES-FI-2017-3-0009, respectively, Postprint (author's final draft)