Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Centrifugal compressor influence on condensation due to Long Route-Exhaust Gas Recirculation mixing

  • Galindo, José|||0000-0001-6068-182X
  • Navarro, Roberto|||0000-0003-2587-4954
  • Tarí, Daniel
  • García -Olivas, Guillermo
[EN] State of the art techniques for reducing pollutant emission in internal combustion engines often require local flow assessment, specially in the air management field. This work addresses the interaction between a turbo- charger compressor and the 3-way long-route EGR joint, where exhaust gases of the combustion are mixed with fresh air. A validated methodology for compressor simulation is combined with a validated condensation model for this work. Numerical simulations of two different working points with three flap positions are conducted. The influence of these operating conditions on the flow field is evaluated. Particularly, there is a connection between the mixing of both steams and the generation of water condensates, responsible for the erosion of the impeller and the loss of compressor efficiency. Moreover, neglecting the impact of the compressor presence on the condensation production is shown to be of low magnitude, so that simulations without the compressor are regarded as accurate, thus reducing the computational effort by two orders of magnitude., Daniel Taxi is partially supported through contract FPI-S2-2015-1095 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A zonal approach for estimating pressure ratio at compressor extreme off-design conditions

  • Galindo, José|||0000-0001-6068-182X
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Tarí, Daniel
  • Tartoussi, H.
  • Guilain, S.
[EN] Zero-dimensional/one-dimensional computational fluid dynamics codes are used to simulate the performance of complete internal combustion engines. In such codes, the operation of a turbocharger compressor is usually addressed employing its performance map. However, simulation of engine transients may drive the compressor to work at operating conditions outside the region provided by the manufacturer map. Therefore, a method is required to extrapolate the performance map to extended off-design conditions. This work examines several extrapolating methods at the different off-design regions, namely, low-pressure ratio zone, low-speed zone and high-speed zone. The accuracy of the methods is assessed with the aid of compressor extreme off-design measurements. In this way, the best method is selected for each region and the manufacturer map is used in design conditions, resulting in a zonal extrapolating approach aiming to preserve accuracy. The transitions between extrapolated zones are corrected, avoiding discontinuities and instabilities., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: Daniel Tari is partially supported through contract FPI-S2-2015-1095 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the impact of the geometry on the performance of an automotive centrifugal compressor using CFD simulations

  • Galindo, José|||0000-0001-6068-182X
  • Gil, A.|||0000-0001-7192-6992
  • Navarro, Roberto|||0000-0003-2587-4954
  • Tarí, Daniel
[EN] During the latest years, downsizing in internal combustion engines has moved the operating conditions of the compressor closer the surge limit. Surge onset depends on the geometry of the compressor inlet and is difficult to predict. Unfortunately, the determination of the surge line is essential for engine design and calibration, since surge is an oscillating phenomenon that endangers the turbocharger integrity. This work is addressed to study the impact of placing different geometries, namely a tapered duct, a convergent-divergent nozzle and a divergent nozzle in the compressor inlet on different compressor parameters such as stability, efficiency and noise emission. 3D-CFD simulations are performed using the commercial code STAR-CCM+ at both near-surge conditions and high mass flow rate, focusing on the flow structures generated by each configuration. The results are compared with corresponding experimental tests and show a meaningful sensitivity of geometry to the performance, indicating potential benefits of using some of these geometries in turbocharger configurations., Daniel Tarí is partially supported through contract FPI-S2-2015- 1095 of Programa de Apoyo para la Investigación y Desarrollo (PAID) of Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Validation and sensitivity analysis of an in-flow water condensation model for 3D-CFD simulations of humid air streams mixing

  • Galindo, José|||0000-0001-6068-182X
  • Piqueras, P.|||0000-0002-3767-0839
  • Navarro, Roberto|||0000-0003-2587-4954
  • Tarí, Daniel
  • Meano, C. M.
[EN] The mixing of gaseous streams at different humidity and temperature conditions may generate bulk con- densation, which is a particular thermodynamic process that usually implies a great computational effort. A model that provides in-flow condensation predictions without heavily impacting on the simulation time becomes a potential tool for studying situations where the presence of water droplets is a problem. For instance, in a Long- Route Exhaust Gas Recirculation (LR-EGR) system, intake fresh air is mixed with humid and hot exhaust gases, generating water droplets that may impact on the turbo-compressor impeller and produce harmful erosion. Serrano et al. [1] developed a condensation submodel for such purpose. In this work, the 3D CFD methodology is analyzed by means of sensitivity studies on the numerical setup and intake throttle valve angle. Validation of the model is addressed by means of measurements in a fully instrumented continuous flow turbocharger test bench, obtaining quantitative and qualitative agreement. Particularly, a consistent correlation was found between predicted condensation rate and the impeller damage for seven LR-EGR configurations. Moreover, the T-joint geometry is noticed to have a great impact on condensation generation, thus showing the potential of such a 3D model for improving the LR-EGR design., Daniel Tari is partially supported through contract FPI-S2-2015-1095 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the inlet geometry on performance, surge margin and noise emission of an automotive turbocharger compressor

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Navarro, Roberto|||0000-0003-2587-4954
  • Tarí, Daniel
  • Meano, Cesare Maria
[EN] Centrifugal compressor performance at low mass flow rates has become an issue in the latest years due to engine downsizing and the increase of low-end torque request. The principal drawback of this operating region is the appearance of the surge phenomenon, which is strongly affected by the compressor inlet geometry. This work is addressed to study the impact of different inlet geometries on the compressor performance, including compressor efficiency, noise emission and surge margin. An engine test bench is set up with a centrifugal compressor and both steady and transient (tip-out) tests are performed in order to obtain a complete view of the influence of each configuration. The results show a clear sensitivity of the compressor parameters to the variations of the geometry upstream the compressor inlet. (C) 2016 Elsevier Ltd. All rights reserved., Daniel Tari is partially supported through contract FPI-S2-2015-1095 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and verification of an in-flow water condensation model for 3D-CFD simulations of humid air streams mixing

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Navarro, Roberto|||0000-0003-2587-4954
  • Tarí, Daniel
  • Meano, Cesare Maria
[EN] Bulk flow condensation caused by the mixing of air streams at different temperatures and humidities is a thermodynamic process that requires strong assumptions to be calculated with low computational effort. The applicability of a model that correctly predicts this phenomenon has grown recently due in part to the deployment of the Long Route Exhaust Gas Recirculation emission reduction technique in combustion engines and the damage to the turbocharger caused by the condensation produced when the intake air is mixed with the combustion gases. This work is addressed to expose a condensation model that is implemented in a commercial 3D-CFD code and is then verified, checking whether the implemented physical equations are behaving as intended. Finally, a practical application is made, showing the potential of model to predict water condensation in a LR-EGR T-joint. (C) 2018 Elsevier Ltd. All rights reserved., Daniel Tarí is partially supported through contract FPI-S2-2015-1095 of Programa de Apoyo para la Investigación y Desarrollo (PAID) of Universitat Politècnica de València.