Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Significant reduction in processing time for Ca0.95Ce0.05MnO3 thermoelectric ceramics

  • Sotelo, A.
  • Amirkhizi, P.
  • Dura, O.J.
  • García, G.
  • Asensio, A.C.
  • Torres, M.A.
  • Madre, M.A.
  • Kovalevsky, A.
  • Rasekh, Sh.
Attrition-milling process has been applied to Ce-doped CaMnO3 precursors to obtain small grain-size powders. The use of Ce4+ as dopant instead a Rare Earth3+ has allowed decreasing by 50% the atomic proportion of dopant, to obtain equivalent charge carrier concentration, which is required for attaining promising properties for thermoelectric applications. An impressive decrease in thermal processing time was achieved, together with an increase in thermoelectric performances, when compared to classically prepared materials. XRD and SEM analysis have confirmed that the final material is nearly single phase. Moreover, grain sizes and density increase with the sintering duration. These microstructural differences are reflected in a significant decrease in electrical resistivity, when compared to the samples prepared from ball-milled precursors (used as reference), without drastically modifying the Seebeck coefficient values. On the other hand, despite of their high electrical conductivity, thermal conductivity is decreased for short time sintered materials, leading to the highest ZT values at 800 °C (∼0.27) in samples sintered for 1 h at 1310 °C. These values are among the best reported in the literature, but they have been obtained in very short time using a simple, and easily scalable process. The suggested approach presented in this work appears particularly promising for large-scale production of oxide-based thermoelectric modules for power generation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Remarkable variation in microstructural, thermoelectric, and magnetic properties of CaMnO3 through Ce doping

  • Gürsul, M.
  • Çetin, G.
  • Ergin, I.
  • Korkmaz, L.
  • Özçelik, B.
  • Torres, M.A.
  • Madre, M.A.
  • Sotelo, A.
This work reports several alterations in crystal structure, grain size, electrical resistivity, power factor, and magnetic properties of Ce-substituted Ca1-xCexMnO3 samples (x = 0.00, 0.02, 0.04, 0.06, 0.08, and 0.10). XRD analysis has showed that all samples present an orthorhombic perovskite structure with Pnma space group. Microstructure of the samples consists of randomly oriented polygonal-shaped grains whose size increases from 6.06 μm to 6.46 μm with Ce content up to 0.04. Electrical resistivity has considerably decreased with Ce doping due to the enhancement of Mn3+/Mn+4 proportions. Power factor of the samples has been noticeably improved by Ce, and the largest value was obtained in x = 0.06 sample (0.35 mW/K2m at 500 °C). A reduction of Néel temperature from 115 to 96 K was determined from magnetization versus temperature measurements which can indicate the antiferromagnetism suppression with increasing Ce-content. In a related manner, magnetocaloric effect properties of the samples have been enhanced in Ce-doped samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of B-site doping on the thermoelectric performances of Ca0.97Y0.01 La0.01 Yb0.01Mn1-2xNbxMoxO3 thermoelectric ceramics

  • Amirkhizi, P.
  • Torres, M.A.
  • Dura, O.J.
  • Sotelo, A.
  • Madre, M.A.
  • Kovalevsky, A.
  • Rasekh, Sh.
A-, and B-site multiple-doped Ca0.97Y0.01La0.01Yb0.01Mn1–2xNbxMoxO3 was studied for improving its thermoelectric thermoelectric performance. Samples were prepared from planetary milled precursors and sintered at 1310ºC for 12 h. XRD showed that sintered samples are nearly single phase, with small amounts of CaMn2O4. SEM analysis revealed that grain size decreases with Nb and Mo content, leading to lowered electrical resistivity, reaching 6.1 mΩ cm at 800ºC in x = 0.03 samples, 60% lower than that of pristine samples. The highest Seebeck coefficient for doped samples has been obtained for x = 0.005, 210μV/K at 800ºC. A high power factor (0.46 mW/K2 m at 800ºC) has been reached for x = 0.01 samples. However, thermal conductivity did not significantly vary with composition, leading to ZT∼0.27 at 800ºC for x = 0.005 samples, among the best reported in the literature. These results suggest that multi-doping approach opens new paths for integrating calcium manganite-based materials in thermoelectric modules for power generation at high temperatures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of laser wavelength on the thermoelectric properties of Bi1.6Pb0.4Sr2Co2O8 textured ceramics processed by LFZ

  • Amirkhizi, P.
  • Madre, M.A.
  • Dura, O.J.
  • Torres, M.A.
  • Sotelo, A.
  • Kovalevsky, A.
  • Rasekh, Sh.
Bi1.6Pb0.4Sr2Co2O8 samples have been textured by the Laser Floating Zone (LFZ) process using Nd:YAG, and CO2 laser radiation. Using different wavelengths resulted in significant structural and microstructural modifications. Powder XRD patterns showed that the thermoelectric phase is the major one in both cases. Microstructural studies revealed that all samples presented the same phases but with much lower content of secondary ones in those processed with the CO2 laser. Electrical resistivity showed different behavior for the two types of samples, being in general, lower for the CO2 grown rods. Seebeck coefficient is lower for the CO2 grown samples up to 300 °C, and higher in the high-temperature range, reaching 240 μV/K at 650 °C, which is one of the highest values obtained so far in these compounds. Moreover, thermal conductivity at 600 °C for these samples (0.93 W/K m) is among the lowest reported in the literature. As a consequence, ZT values at 600 °C reached 0.42 in CO2 textured materials, about two times higher than the obtained in Nd:YAG ones. This value is among the highest reported so far in the literature, and is comparable to the performance attained for the same composition containing nanoparticles addition. All these properties, combined with the fact that the processed materials can be directly integrated into thermoelectric modules, render them highly attractive for industrial production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of B-site doping on the thermoelectric performances of Ca0.97Y0.01 La0.01 Yb0.01Mn1-2xNbxMoxO3 thermoelectric ceramics

  • Amirkhizi, P.
  • Torres, M.A.
  • Dura, O.J.
  • Sotelo, A.
  • Madre, M.A.
  • Kovalevsky, A.
  • Rasekh, Sh.
A-, and B-site multiple-doped Ca0.97Y0.01La0.01Yb0.01Mn1–2xNbxMoxO3 was studied for improving its thermoelectric thermoelectric performance. Samples were prepared from planetary milled precursors and sintered at 1310ºC for 12 h. XRD showed that sintered samples are nearly single phase, with small amounts of CaMn2O4. SEM analysis revealed that grain size decreases with Nb and Mo content, leading to lowered electrical resistivity, reaching 6.1 mΩ cm at 800ºC in x = 0.03 samples, 60% lower than that of pristine samples. The highest Seebeck coefficient for doped samples has been obtained for x = 0.005, 210μV/K at 800ºC. A high power factor (0.46 mW/K2 m at 800ºC) has been reached for x = 0.01 samples. However, thermal conductivity did not significantly vary with composition, leading to ZT∼0.27 at 800ºC for x = 0.005 samples, among the best reported in the literature. These results suggest that multi-doping approach opens new paths for integrating calcium manganite-based materials in thermoelectric modules for power generation at high temperatures.