Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 23
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Towards Stable Free Lead Mixed Halide Perovskite Thin Films on FTO-Coated Glass Substrate

  • Doumbia, Youssouf
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] All-inorganic cesium (Cs) lead perovskites have better thermal and chemical stability than organic-inorganic hybrids. They therefore represent a hope for stability and increased performance of perovskites as absorber layers in photovoltaic solar cells. In the present work, we have deposited different layers on FTO-coated glass substrates using the one-step spin-coating method. The results of the lead substitution are presented and critically discussed. The X-ray diffraction (XRD) results show four peaks for all three samples. The main peaks of the different films are located at the 2? angles of 26.45 & DEG; and 51.50 & DEG; for the Muller indices (220) and (242), respectively. These two main peaks indicate that the prepared thin films all have two preferred crystallographic orientations. Beyond these two main peaks, we have two other smaller peaks at 2? of 33.67 & DEG; and 37.70 & DEG; corresponding to the Muller indices of (210) and (211), respectively. The smoother the surface of the thin films, the more light they reflect, resulting in poor light absorption by the films. It is therefore important to obtain a surface image of the prepared films, as the larger the surface image, the better the film. With this in mind, we carried out a scanning electron microscope (SEM) analysis, which gave us the surface images. Figure 3 shows the SEM images of thin CsPb1-xSnxI1.5Br1.5 layers (x = 0, 0.5, and 1) grown on FTO-coated glass substrate with different [Pb]/[Sn] ratios. As can be seen from the figure, the effect of the [Pb]/[Sn] ratio is visible in the surface images of the different thin films. The smallest grain size is that of the unsubstituted CsPbI1.5Br1.5, while the largest grain size corresponds to the partially Pb-substituted layer (CsPb0.5Sn0.5I1.5Br1.5). The fully Pb-substituted layer (CsSnI1.5Br1.5) has an intermediate grain size. The surface images of the films show that the surfaces are well coated with grain sizes that vary greatly depending on the layer. The best grain size is that of the thin film with partial lead substitution (CsPb0.5Sn0.5I1.5Br1.5). Regarding the UV-visible absorption of the different films, we can say that the films absorb the maximum amount of light in the wavelength range of 350-550 nm. Above 550 nm, the absorption coefficients drop significantly. The absorption coefficients of the tin-free (Sn) layer remain higher than the coefficients of the other layers throughout the UV-visible spectrum. The degradation study revealed that the Sn-free layer retains good light absorption compared to the other layers after 4 weeks of exposure to the ambient environment. The crystal structure of all the layers shows good resistance to the elements during the 4 weeks, as shown by the renewed XRD results after the 4 weeks of exposure., Author Youssouf Doumbia acknowledges his grant from Erasmus+ KA 107. The author Amal Bouich acknowledges MCIN for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033). The Postdoctoral contract Margarita Salas financed with the union European Next Generation EU. This research has been funded by Grant PID2019-107137RB-C22 funded by MCIN/AEI/ and by "ERDF A way of making Europe".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Diversity of RNA Viruses and Circular Viroid-like Elements in Heterobasidion spp. in Near-Natural Forests of Bosnia and Herzegovina

  • Dálya, Laszlo Benedek
  • Hejna, Ondrej
  • Stanivukovic, Zoran
  • Kudlácek, Tomas
  • Botella, Leticia
  • La Peña Del Rivero, Marcos De|||0000-0002-7949-8459
[EN] Heterobasidion root rot fungi represent a major threat to conifer forest stands, and virocontrol (biocontrol) has been proposed as an alternative strategy of disease management in recent years. Here, we investigated the occurrence of RNA viruses and viroid-like genomes in Heterobasidion annosum sensu lato in near-natural forests of Bosnia and Herzegovina (Dinaric Alps), a region previously unexplored in this regard. Seventeen H. annosum s.l. isolates were screened for virus presence by RNA Sequencing and bioinformatic analyses. In total, 32 distinct mycoviruses were discovered in the datasets, 26 of which were previously unknown. The detected viruses represent two dsRNA (Partitiviridae and Curvulaviridae), six linear ssRNA (Mitoviridae, Narnaviridae, Botourmiaviridae, Virgaviridae, Benyviridae, and Deltaflexiviridae) and three circular ssRNA (Dumbiviridae, Quambiviridae, and Trimbiviridae) virus families. In addition to the known circular ambiviruses with their hammerhead (HHRz) and hairpin (HPRz) ribozymes, two other smaller non-coding circular RNAs of ca. 910 bp each were identified encoding HHRz and deltavirus (DVRz) ribozymes in both polarities of their genomes. This study documents the first report of a putative viroid-like RNA agent in Heterobasidion, along with beny-like and deltaflexivirus-like viruses in Heterobasidion abietinum, and expands the known virosphere of Heterobasidion species in Southeastern European forests., This work was supported by the European Regional Development Fund, Project "Phytophthora Research Centre", Reg. No. CZ.02.1.01/0.0/0.0/15_003/0000453. M.dlP. was supported by the Generalitat Valenciana through the PROMETEO program, Project CIPROM/2022/21. The first author's internship at the University of Banja Luka was supported by an Erasmus + grant (ERASMUS + 2020-1-CZ01-KA107-078115) funded by the EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improving Stability and Performance of Cesium Mixed Lead Halides for Photovoltaic Applications

  • Doumbia, Youssouf
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] We have focused on mixed halide perovskite thin films of the formula CsPbX3 where (X-3 = Br-3, Cl-3, I-3, Br2Cl, Br2I, and I2Cl) prepared by spin-coating in order to study the effects of partial and total Br substitution. For this purpose, we performed a series of characterizations, including x-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-visible spectroscopy. All the films except CsPbI2Br showed two characteristic peaks at 2 theta angles of 26.80 degrees and 51.80 degrees corresponding to the (111) and (220) crystallographic planes. In the case of CsPbI2Br, we have the same peaks, but the main ones are located at 15 degrees and 30 degrees for the (100) and (200) planes, respectively. SEM examined the surface morphology of the different mixed lead halide films; the best surface was that of the CsPbBr2I sample, which is well-coated, dense, with no pinholes and no cracks, and has the largest grain size. In addition, all the mixed halide films showed good absorbance, especially between 600 nm and 900 nm, with band gap values between 1.94 and 2.92 eV., Author Youssouf Doumbia acknowledges his grant from Erasmus+ KA 107. Author Amal Bouich acknowledged the post-doctoral contract supported by the RRHH, the Postdoctoral contract Margarita Salas financed with the union European Next Generation EU. This research has been funded by Grant PID2019-107137RB-C22 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Insight of ZnO/CuO and ZnO/Cu2O solar cells efficiency with SCAPS simulator

  • Klegayere Emmanuel, Kone
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] Despite the low power conversion efficiency of solar cells n-ZnO/p-CuO and n-ZnO/p-Cu2O, they can contribute to the development of photovoltaic energy. To optimize their yields, the simulator software SCAPS-1D was used in this work to do the simulations of the two cells (Fig. 1) by varying certain parameters. Its parameters were thickness, bandgap, shallow uniform donor density (ND) for the ZnO, and shallow uniform acceptor density (NA) for the CuO and Cu2O. The values optimized of these parameters gave short-circuit currents and efficiencies of 27.7755 mA.cm¿2, 31.40%, and 12.9790 mA.cm¿2, 13.34% respectively for the solar cells n-ZnO/p-CuO and n-ZnO/p-Cu2O (Fig. 2). Our results reveal that the n-ZnO/p-CuO solar cell is more efficient than the n-ZnO/p-Cu2O solar cell and can be used for converting solar energy into electricity., This research has been funded by Grant PID2019-107137RB-C22 funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe. Erasmus+ (Grant No. KA107), Union European next Generation EU, (Grant No. RRHH), The author Amal Bouich acknowledges MCIN for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Picture Fuzzy Distance Measure in Controlling Network Power Consumption

  • Roan, Ngan Thi
  • Andújar, Fran
  • Le, Son Hoang
  • Vu, Manh Van
  • Smarandache, Felorentin
  • Coll, Salvador|||0000-0002-7795-7252
  • Alonso Díaz, Marina|||0000-0001-7079-5898
  • Martínez-Rubio, Juan-Miguel|||0000-0002-9748-0332
  • López Rodríguez, Pedro Juan|||0000-0003-4544-955X
[EN] In order to solve the complex decision-making problems, there are many approaches and systems based on the fuzzy theory were proposed. In 1998, Smarandache introduced the concept of single-valued neutrosophic set as a complete development of fuzzy theory. In this paper, we research on the distance measure between single-valued neutrosophic sets based on the H-max measure of Ngan et al. [8]. The proposed measure is also a distance measure between picture fuzzy sets which was introduced by Cuong in 2013 [15]. Based on the proposed measure, an Adaptive Neuro Picture Fuzzy Inference System (ANPFIS) is built and applied to the decision making for the link states in interconnection networks. In experimental evaluation on the real datasets taken from the UPV (Universitat Politècnica de València) university, the performance of the proposed model is better than that of the related fuzzy methods., This work has been supported by MINECO and the European ERDF under grants PID2019-105903RB-I00 and RTI2018-098156-B-C51. The autor (R.T. Ngan) also would like to thank the Erasmus+ Mobility Program (2016-1-ES01-KA107-023453) for supporting her work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Elaboration et caractérisation de couches minces de cuivre, indium, gallium et sélénium (CIGS) pour cellules solaires

  • Armel Ignace, N'Guessan
[ES] Este proyecto de investigación se centra en el campo de las energías renovables y más concretamente de la energía solar fotovoltaica. La tesis se ha focalizado en el desarrollo de películas delgadas de Cobre-Indio-GalioSelenio o Sulfuro (CuIn1-xGax(Se,S)2) con técnicas de bajo coste. La mayoría de las celdas basadas en CIGS utilizan el CdS como capa de búfer. En nuestro experimento, usaremos otra capa de tampón como SnS2 o ZnO1-xSx como alternativa a CdS para mejorar nuestra célula. El estudio se centrará en el contacto tampón/absorbedor para reducir la recombinación. En este trabajo, reportamos la investigación experimental del desarrollo y desarrollo de la caracterización de la calcopirita de cobre, indio, galio y selenio (CIGS) por la técnica de electrodeposición y pulverización. Además, nos hemos centrado en el contacto entre la capa generadora que es el absorbedor y el circuito externo. Las propiedades eléctricas de este contacto dependen principalmente del proceso de deposición de la capa absorbente en el contacto trasero utilizado. Por lo tanto, será necesario controlar el crecimiento de la capa interfacial de MoSe2 entre el absorbedor y el contacto posterior en el caso del molibdeno para obtener un rendimiento óptimo. Por supuesto, la eficiencia de la célula depende de un gran número de parámetros experimentales y varía según los métodos de fabricación, especialmente la capa absorbente CIGS. En nuestro caso, las técnicas utilizadas son la galvanoplastia y la pirólisis por pulverización para la deposición de películas CIGS. Estas técnicas son más baratas, prácticamente alcanzables en cualquier laboratorio y dan un buen rendimiento. Por lo tanto, mediante técnicas de deposición de bajo coste hemos estudiado el comportamiento de la célula solar con una capa de MoSe2 como capa interfacial y el efecto de la banda prohibida de la capa formada y la capa tampón utilizada sobre los parámetros de las células solares CIGS. Los resultados de este estudio podrían ayudar a mejorar el rendimiento de las células solares CIGS utilizando técnicas de bajo coste., [CA] Aquest projecte de recerca es centra en el camp de les energies renovables i més concretament en l'energia solar fotovoltaica. La tesi s'ha centrat en el desenvolupament de pel·lícules primes de Coure-Indi-Gali-Seleni o Sulfur (CuIn1-xGax(Se,S)2) amb tècniques de baix cost. La majoria de les cel·les basades en CIGS utilitzen el CdS com a capa de búfer. En el nostre experiment, farem servir una altra capa de tampó com ara SnS2 o ZnO1-xSx com a alternativa al CdS per millorar la nostra cel·la. L'estudi es centrarà en el contacte tampó/absorbidor per reduir la recombinació. En aquest treball, reportem la recerca experimental del desenvolupament i la caracterització de la calcopirita de coure, indi, gali i seleni (CIGS) mitjançant la tècnica d'electrodeposició i pulverització. A més, ens hem centrat en el contacte entre la capa generadora que és l'absorbidor i el circuit extern. Les propietats elèctriques d'aquest contacte depenen principalment del procés de deposició de la capa absorbent en el contacte posterior utilitzat. Per tant, serà necessari controlar el creixement de la capa interfacial de MoSe2 entre l'absorbidor i el contacte posterior en el cas del molibdè per obtenir un rendiment òptim. És clar que l'eficiència de la cel·la depèn d'un gran nombre de paràmetres experimentals i varia segons els mètodes de fabricació, especialment la capa absorbent CIGS. En el nostre cas, les tècniques utilitzades són la galvanoplàstia i la piròlisi per pulverització per a la deposició de pel·lícules CIGS. Aquestes tècniques són més econòmiques, pràcticament assolibles en qualsevol laboratori i proporcionen un bon rendiment. Per tant, mitjançant tècniques de deposició de baix cost hem estudiat el comportament de la cel·la solar amb una capa de MoSe2 com a capa interfacial i l'efecte de la banda prohibida de la capa formada i la capa tampó utilitzada sobre els paràmetres de les cel·les solars CIGS. Els resultats d'aquest estudi podrien ajudar a millorar el rendiment de les cel·les solars CIGS utilitzant tècniques de baix cost., [EN] Our research project aims at the field of renewable energies and more specifically, photovoltaic solar energy, i.e. solar cells, our study focuses on the elaboration of Copper-Indium-Gallium-Selenium or Sulfide (CuIn1-xGax(Se,S)2 thin films for solar cells with low-cost techniques also to develop the performance of the typical solar cell structure: n-ZnO/i-ZnO/n-tampon/p-CIGS/p+-MoSe2/back contact. Most of the CIGS based cells use CdS as a buffer layer. In our experiment, we will make use of another buffer layer such as SnS2 or ZnO1-xSx as an alternative to CdS to improve our cell. The investigation will be carried out on the buffer/absorber contact to reduce recombination. In addition, we will focus on the contact between the generating layer which is the absorber and the external circuit. The electrical properties of this contact depend essentially on the deposition process of the absorber layer on the back contact used. It will thus be necessary to control the growth of the MoSe2 interfacial layer between the absorber and the back contact in the case of Molybdenum in order to obtain an optimal yield. Obviously, the yield of the cell depends on a large number of experimental parameters and varies according to the fabrication methods, especially of the CIGS absorber layer. In our case the techniques used are electrodeposition and spray pyrolysis for the deposition of CIGS films, there techniques are cheaper, practically feasible in the laboratory and give good performance. Therefore, we will investigate, using low-cost deposition techniques, the performance of the cell with a MoSe2 layer as an interfacial layer and the effect of the bandgap of the formed layer and the buffer layer used on the parameters of the CIGS solar cells. The results of this study could help to improve the performance of the CIGS solar cell using low-cost techniques.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Cyber-Resilient Controllers for Smart Distribution Grid Control Layers

  • Chandramathi, Jishnu Sankar Vijayasekharan
  • Nair, Manjula G.
  • Álvarez, Carlos|||0000-0002-8238-1606
[EN] This paper presents a novel cyber-resilient control strategy for enhancing the operational security of future smart distribution systems (SDSs) against compromised control setpoints originating from higher-level controllers. The proposed framework addresses the structure, control architecture, and cyber vulnerabilities of SDSs by embedding an anomaly detection and autonomous response mechanism within each control layer. An artificial neural network (ANN)-based detector is employed to identify non-implementable or malicious control commands based on local measurements and grid location data. Upon detecting a cyber anomaly, the controller avoids disconnection and enables droop-based autonomous operation, ensuring continued grid support. The proposed strategy was validated using MATLAB/Simulink R2022a under various dynamic test scenarios, demonstrating its ability to maintain system stability. Unlike prior studies that rely on offline anomaly detection, this study presents a real-time capable closed-loop control solution that detects anomalies during simulation runtime. The proposed method rejects erroneous commands arising from both cyber intrusions and human errors, thereby enhancing the cyber-resilience and reliability of SDS operations., This research was partially funded by Erasmus+ KA107.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Migration cost optimization for service provider legacy network migration to software-defined IPv6 network

  • Dawadi, Babu R.
  • Rawat, Danda B.
  • Joshi, Shashidhar R.
  • Keitsch, Martina M.
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] This paper studies a problem for seamless migration of legacy networks of Internet service providers to a software-defined networking (SDN)-based architecture along with the transition to the full adoption of the Internet protocol version 6 (IPv6) connectivity. Migration of currently running legacy IPv4 networks into such new approaches requires either upgrades or replacement of existing networking devices and technologies that are actively operating. The joint migration to SDN and IPv6 network is considered to be vital in terms of migration cost optimization, skilled human resource management, and other critical factors. In this work, we first present the approaches of SDN and IPv6 migration in service providers' networks. Then, we present the common concerns of IPv6 and SDN migration with joint transition strategies so that the cost associated with joint migration is minimized to lower than that of the individual migration. For the incremental adoption of software-defined IPv6 (SoDIP6) network with optimum migration cost, a greedy algorithm is proposed based on optimal path and the customer priority. Simulation and empirical analysis show that a unified transition planning to SoDIP6 network results in lower migration cost., U.S. National Science Foundation (NSF), Grant/Award Number: CNS 1650831 and HRD 1828811; ERASMUS+ KA107; Nepal Academy of Science and Technology (NAST); Norwegian University of Science and Technology; University Grant Commission (UGC), Nepal, Grant/Award Number: FRG/74_75/Engg-1
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optical and structural investigation of methylammonium lead perovskite mixed halide (I, Br, and Cl) on spin-coated zinc oxide

  • Klegayere Emmanuel, Kone
  • Marí Soucase, Bernabé
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
[EN] This study investigated the effect of mixing different halides bromine (Br) with iodine (I) and Br with chlorine (Cl) and using only bromide for methylammonium lead perovskites films deposited in ZnO to produce different heterojunctions ZnO/MAPbBr3, ZnO/MAPbBr2I and ZnO/MAPbBr2Cl. Thus, these three heterojunction samples were produced and characterized. The perovskite is deposited at ZnO films showed two main peaks located at 2¿ = 33.66° and 2¿ = 37.69°. These peaks correspond to the (0 0 2) and (1 0 1) planes of the hexagonal wurtzite structure of ZnO respectively. The XRD results indicate that all the heterojunction samples show two main peaks at 2¿ = 14.79° and 2¿ = 29.83° for the (1 0 0) and (2 0 0) crystallographic planes respectively. The peaks of the sample mixed with iodine are the most intense and those of the sample mixed with chlorine are the least intense. These results also reveal that the mixed samples have lower crystallinity than the unmixed ZnO/MAPbBr3 sample. The SEM results confirmed this. The UV¿Visible results indicate that the sample mixed with iodine absorbs the most and has the smallest band gap of 2.15 eV. The band gaps of the heterojunctions range from 2.15 eV to 2.4 eV. The unmixed sample (ZnO/MAPbBr3) has the largest band gap. The degradation study showed that the sample mixed with iodine degrades faster., Author Klegaye Emmanuel Kone thanks Erasmus + KA107 for the grant. Amal Bouich acknowledges Ministerio de Ciencia e Innovacion (Spain) for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033). This work has been funded by the Conselleria d Innovacio, Universitats, Ciencia i Societat Digital (Generalitat valenciana, Prometeus 2023 CIPROM2022/03) and the Agencia Estatal de Investigacion (Spain) through project PID2019-107137RBC21/AEI/10.13039/501100011033 and by ERDF under the funding Away of making Europe .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

First Report of Tomato Leaf Curl New Delhi Virus Infecting Cucurbit Plants in Algeria

  • Kheireddine, A.
  • Sáez-Sánchez, Cristina
  • Sifres Cuerda, Alicia Gemma|||0000-0002-9498-0083
  • Picó Sirvent, María Belén|||0000-0001-7761-990X
  • López Del Rincón, Carmelo|||0000-0001-7459-1315
This work was supported by the Spanish Ministerio de Ciencia, Innovacion y Universidades, cofunded with FEDER funds (project nos. AGL2017-85563-C2-1-R and RTA2017-00061-C03-03 [INIA]) and the programa para grupos de investigacion de excelencia from the Conselleria d'Educacio, Investigacio, Cultura i Esport, (Generalitat Valenciana) (Prometeo Program 2017/078). A. Kheireddine thanks the Erasmus+ Programme of the European Union for her mobility project (KA107 2018-20). C. Saez is a recipient of a predoctoral fellowship from Generalitat Valenciana, cofunded by the Operational Program of the European Social Fund (FSECV 2014-2020) (grant no. ACIF/2016/188).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Photocatalytic degradation of pharmaceuticals using natural sand-based TiO2 catalysts: Preparation, characterization, and reactivity

  • Chahid, Abdessalim
  • Zahraoui, Brahim
  • Lahcene, Driss
  • Bosca Mayans, Francisco
  • Marín García, Mª Luisa|||0000-0002-9789-8894
[EN] Quartz sand collected from the dunes of Taghit, a region of Bechar in southwestern Algeria, served a dual purpose in this study. Firstly, it acted as a natural support for the TiO2 photocatalyst. Secondly, it served as a lowcost precursor for silica extraction through an alkaline fusion process. TiO2 nanoparticles were efficiently immobilized on both Dune Sand (TiO2-DS) and extracted silica (TiO2-SP) using an organometallic coating approach, providing a versatile TiO2-based photocatalyst solution. Characterizing the prepared catalysts included techniques such as ICP, N2 adsorption XRD, FTIR, FESEM, and XPS. It was noted that TiO2 exhibited a well-coated layer on both dune sand and extracted silica, demonstrating a prominent anatase crystalline phase. Chemical composition analysis revealed the presence of chemical bonds between Ti and Si in the TiO2-SP and TiO2-DS samples. Moreover, TiO2 particles showed improved dispersion on the surface of TiO2-SP compared to TiO2-DS due to the larger specific surface area of the extracted silica resulting in S BET of 83.74 m2.g-1 for TiO2-SP compared to 30.15 m2.g-1 for TiO2-DS. The photocatalytic performance of TiO2-DS and TiO2-SP was compared to P25 in the abatement of three common pharmaceutical compounds: amoxicillin (AMO), ibuprofen (IBU), and acetaminophen (ACT), with a focus on the influence of the support material on photoactivity. TiO2-SP exhibited a slight advantage in terms of mineralization with 90 %, 92 %, and 99 % after 300 min for ACT, AMO, and IBU, respectively, Whereas the TiO2-DS catalyst resulted in slightly lower results of 81 %, 85 %, and 97 % for the same drugs over the same irradiation period. Additionally, both TiO2-SP and TiO2-DS demonstrated easy separation from the reaction medium by quick sedimentation upon agitation cessation. In contrast, P25 remained in a colloidal suspension., This project gratefully acknowledges the financial support from the European Union as part of the Erasmus + KA1017 project. Special appreciation is extended to the Universitat Politecnica de Valencia (UPV) and the Instituto de Tecnologia Quimica (ITQ) for their invaluable contributions and support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Legacy Network Integration with SDN-IP Implementation towards a Multi-Domain SoDIP6 Network Environment

  • Dawadi, Babu R.
  • Rawat, Danda B.
  • Joshi, Shashidhar R.
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] The logical separation of the data plane and the control plane of the network device conceptually defined by software-defined networking (SDN) creates many opportunities to create smart networking with better efficiency for network management and operation. SDN implementation over telecommunications (Telcos) and Internet service provider (ISP) networks is a challenging issue due to the lack of a high maturity level of SDN-based standards and several other critical factors that are considered during the real-time migration of existing legacy IPv4 networks. Different migration approaches have been studied; however, none of them seem to be close to realizing implementation. This paper implements the SDN-IP and Open Network Operating System (ONOS) SDN controller to migrate legacy IPv4 networks to multi-domain software-defined IPv6 (SoDIP6) networks and experimentally evaluate the viability of joint network migration in the ISP networks. We present results using extensive simulations for the suitable placement of the master ONOS controller during network migration by considering minimum control path latency using optimal path routing and the breadth first router replacement (BFR) technique. Our empirical analysis and evaluations show that the identification of the median router to attach the master controller and router migration planning using BFR give better results for carrier-grade legacy networks' migration to SoDIP6 networks., This research was partially funded by the Norwegian University of Science and Technology, Trondhiem, Norway (NTNU) under Sustainable Engineering Education Project (SEEP) financed by EnPE, University Grant Commission (grant-ID: FRG7475Engg01), Bhaktapur, Nepal, Nepal academy of Science and Technology (NAST), Kathmandu, Nepal, and U.S. National Science Foundation (NSF). The work of Danda B. Rawat was partly supported by the U.S. National Science Foundation (NSF) under grants CNS 1650831 and HRD 1828811. Any opinions, findings, and conclusions or recommendations expressed in this article are those of the authors and should not be interpreted as necessarily representing the official policies, either expressed or implied, of the NSF. We are thankful to the ERASMUS+ KA107 project and the GRC lab team members at Universitat Politècnica De València for the research support and facilitation.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Investigation On The Crystallinity And Optoelectronic Properties Of Thin Films Of Zno/Mapbx3heterojunctionsynthesized Via The Spin-Coating Method

  • Soro, Donafologo
  • Kone, Klegayere Emmanuel
  • Marí-Guaita, Julia
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] In this paper, thin layers of ZnO were deposited onto fluorine-doped tin oxide (FTO) substrates. Subsequently, different layers of perovskite (MAPbX3, X = I, Br, Cl) were spin-coated onto these ZnO layers. The resulting layers were characterized using X-ray diffraction (XRD), UV-Visible spectroscopy, and scanning electron microscopy (SEM). Special attention was given to the surface topography, the crystallinityand optoelectronic properties.XRD analysis of all the thin layers showed two diffraction peaks for the ZnO/MAPbX3 heterojunction corresponding to the crystallographic planes (100) and (200). The ZnO/MAPbBr3 peaks were more intense than the peaks from the ZnO/MAPbI3 and ZnO/MAPbCl3 samples. SEM images showed the crystalline nature of the produced thin layers. The grain size of the ZnO/MAPbBr3 sample was approximately 747.00 nm, while those of the ZnO/MAPbI3 and ZnO/MAPbCl3 samples were 412.00 nm and 330.55 nm, respectively. UV-visible characterization demonstrated that the iodine-based sample had the highest solar radiation absorption and had the smallest bandgap, with Eg = 1.95 eV., The authors acknowledge the support provided by Erasmus+ KA 107 which offers scholarships for the realization of this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evolutionary gaming approach for decision making of Tier-3 Internet service provider networks migration to SoDIP6 networks

  • Dawadi, Babu R.
  • Rawat, Danda B.
  • Joshi, Shashidhar R.
  • Manzoni, Pietro|||0000-0003-3753-0403
[EN] With the increasing number of Internet of Things (IoT) devices, current networking world is suffering in terms of management and operations with lack of IPv4 addresses leading to issues like network address translation (NAT) proliferation, security and quality of services. Software-defined networking (SDN) and Internet Protocol version 6 (IPv6) are the new networking paradigms evolved to address related issues of legacy IPv4 networking. To adapt with global competitive environment and avoid all existing issues in legacy networking system, network service providers have to migrate their networks into IPv6 and SDN-enabled networks. But immediate transformations of existing network are not viable due to several factors like higher cost of migration, lack of technical human resources, lack of standards and protocols during transitions, and many more. In this paper, we present the migration analysis for proper decision making of network transition in terms of customer demand, traffic engineering, and organizational strength with operation expenditure for network migration using evolutionary gaming approach. Joint migration to SDN-enabled IPv6 network from game theoretic perspective is modeled and is validated using numerical results obtained from simulations. Our empirical analysis shows the evolutionary process of network migration while different internal and external factors in the organization affect the overall migration. Evolutionary game in migration planning is supportive in decision making for service providers to develop suitable strategy for their network migration. The proposed approach for migration decision making is mostly applicable to fairly sustained service providers who lack economics, regulation/policy, and resources strengths., ERASMUS+, Grant/Award Number: KA107; UGC-NP, Grant/Award Number: FRG-074/75-Engg-01; NTNU-EnPE-MSESSD; US National Science Foundation, Grant/Award Numbers: CNS 1650831, HRD 1828811; NAST
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Surface Morphology And Optical Properties Of Ma-Doped Fapbbr3 Thin Films For Photovoltaic Applications

  • Soro, Donafologo
  • Doumbia, Youssouf
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] In general, the optical and structural properties of perovskites can be improved by doping in order to use them for various applications. In this work, we have developed by the method of spin coating in one step thin layers of FA1-xMAxPbBr3, x gradually taking the values0.2 0.4 0.6 0.8 and 0.1. An analysis of the structural and optical properties was made after their characterization. The results obtained indicate thatthe thin films produced exhibit low dislocation densities and good lattice strain values. All have a main peak of maximum intensity located at the 2Ɵ angle of 26.84° for the crystallographic plane (111) and their grain size decreases with the increase in the percentage of methylammonium (MA) from 501 nm to 452 nm. From the morphological point of view, we have well-covered, dense and crack-free surfaces. We also obtained an improvement in the band gap which gradually decreases during doping from 2.68eV for 2% MA to 2.40 eV for 10% MA. At the end of our study, it should be noted that MA-doped FAPbBr3 thin films are of goodquality and can be used in the photovoltaic field., The authors acknowledge the support provided by Erasmus+ KA 107 which offers scholarships for the realization of this research..
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Investigation of mixed bromide iodide lead perovskites by spin coating onto single and tandem solar cells applications

  • Armel Ignace, N'Guessan
  • Doumbia, Youssouf
  • D. Soro
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] In this study mixed bromide iodide lead perovskites CH3NH3PbI3-xBrx were successfully deposed at Fluorine doped Tin Oxide (FTO) coated glass substrate by Spin coating process. We investigated the processing substitution of PbI3 by PbBr3 in CH3NH3PbI3-xBrx.We also studied the structural and optical properties in Br-gradient MAPbI3-xBrx perovskites thin film deposited using UV-vis absorption and X-ray diffraction of each mixed halide (I/Br) perovskites film and nanostructured for solar cell applications. The surface morphology of mixed halide perovskite films deposited was analyzed by Scanning electron microscopy (SEM). We observed that peaks are shifted toward the higher 2 theta direction as Br content increases, moving from a tetragonal to a cubic structure. The perovskite films deposited show bandgap increasing with Br content. We also used device simulation to study the impact of various compositions of Br on single, and tandem proposed solar cells' performance. In consideration of the Br rate, the suitable device for adequate Br rate in solar cell application has been considered. The tandem J-V shows a short-circuit current density (Jsc) of 38.81 mA/cm2, an open-circuit voltage (Voc) of 1.54 V, fia ll factor (FF) of 73.32 % a,nd Pa CE of 43.84 %., Author N'Guessan Armel Ignace acknowledges his Erasmus+KA 107 grant. The author Amal Bouich acknowledges MCIN for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/ 501100011033) and NextGenerationEU. This research has been funded by Grant PID2019-107137RB-C22 funded by MCIN/AEI/10.13039/ 501100011033 and by "ERDF A way of making Europe"
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synthesis and characterization of kesterite Cu2ZnSn (SxSe1-x) 4 thin films with low-cost for efficient solar cells

  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] In this study, we conducted an investigation on the Cu2ZnSnS4 (CZTS) k¿esterite compound, which is considered an attractive material for its favorable absorption properties, making it a suitable semiconductor for photovoltaic applications. However, its market potential is limited by its low efficiency of 12.6%, primarily caused by the presence of secondary phases that act as recombination centers. Theoretically, the efficiency limit for CZTS ranges from 31% to 33%. To enhance the photovoltaic performance of CZTS, we employed a doping strategy by incorporating selenium (Se) into the Cu2ZnSn(SxSe1-x)4 film, where the sulfur-to-selenium ratio (S/Se) was optimized within the range of 0< x <1. The CZTS films were deposited onto FTO substrates using the spray pyrolysis technique, which is a simple and cost-effective method. The characterization of these films involved X-ray diffraction (XRD) and UV¿visible spectroscopy analysis. Additionally, the morphology and topography of the CZTSSe layers were examined using scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. Trans mission electron microscopy (TEM) was also employed. The results obtained in this study indicate that CZTSSe films exhibit band gap values ranging from 1.54 eV to 1.68 eV and grain compactness, with larger agglomerated grains on the film surface when the S/Se ratio is approximately 0.5 or lower. Moreover, the resistivity measurements revealed significant variations when sulfur and selenium were combined, suggesting the influence of their composition on the electrical properties of the CZTS films., Aka Hyacinthe AKA acknowledged Erasmus107 for the grant, The author Amal Bouich acknowledges MCIN for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033). This work has been funded by the Ministerio de Ciencia e Innovacio¿n (Spain) and by the Spanish Agencia Estatal de Investigacio¿n through projects BESTMAT PID2019-107137RB-C21/AEI/10.13039/501100011033 and PID2019-107137RB-C22/AEI/10.13039/501100011033 and by ERDF under the funding A way of making Europe
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

From Powder Manufacturing to Perovskite/&lt, i&gt, p&lt, /i&gt, -type TCO Thin Film Deposition

  • Doumbia, Youssouf
  • Touré, Abdoulaye
  • Mari Guaita, Julia
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] Photovoltaic perovskites are very attractive candidates as absorber layers because of their very interesting properties. In the present work, we have two parts: first, we prepared powders of the perovskites MAPbBr3, MAPbI3, and MAPbCl3, with the aim of maximizing their purity, and then we deposited thin films using these powders previously prepared by the one-step spin-coating method. The anti-solvent used was under the same ambient deposition conditions. We concluded with a series of characterizations such as X-ray diffraction, scanning electron microscopy, and UV-visible absorption to better appreciate the quality of the films produced. The crystalline structures of the films, their surface morphology, and their optical properties from the characterizations show that we have succeeded in producing film samples suitable for photovoltaics., Author Youssouf Doumbia acknowledges his grant from Erasmus+ KA 107. The author Amal Bouich postdoctoral researcher acknowledges a Margarita Salas Fellowship (MCIN/AEI/https://doi.org/10.13039/501100011033) for funding support. This work was supported by the EU with Project PID2019-107137RB-C22 and by ERDF under the funding "A way of making Europe".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Insight into the effect of halogen X in methylammonium lead halide (MAPbX3) spin-coated on zinc oxide film

  • Kone, Klegayere Emmanuel
  • Marí-Guaita, Julia
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] Herein, we investigated the effect of halogen X in methylammonium lead halide (MAPbX3) where X = (Iodide/ Bromide, or Chloride) deposited by spin coating technique on a zinc oxide layer. The ZnO films were first deposited on Fluorine-doped Tin Oxide (FTO) substrates. Then, the perovskite solutions (MAPbI3, MAPbBr3, and MAPbCl3) were deposited on the ZnO layer. The films obtained were characterized by X-ray diffraction (XRD), UV¿Visible spectroscopy, and Scanning Electron Microscopy (SEM). The XRD analysis shows characteristic peaks of the ZnO/MAPbX3 heterojunction corresponding to the (100) and (200). The ZnO/MAPbBr3 peaks are more intense than other sample peaks. This analysis also shows the crystalline character of the films produced. SEM images also show the good crystallinity of the films produced. The images show that the grain sizes of the sample ZnO/MAPbBr3 are the largest compared to others. The UV¿visible characterization showed that the iodine-based sample absorbed better and had a good band gap (Eg = 1.95 eV). The degradation study was carried out after two weeks of the deposition. The results showed that the iodine-based sample degrades faster compared to another halogen. These findings are helpful in producing stable and efficient perovskite-based solar cells., Author Klegayere Emmanuel Kone thanks Erasmus + KA107 for the grant. This work has been funded by the Ministerio de Ciencia e Innovacion (Spain) and by the Spanish Agencia Estatal de Investigacion through projects BESTMAT PID2019-107137RB-C21/AEI/10.13039/501100011033 and PID2019-107137RB-C22/AEI/10.13039/501100011033 and by ERDF under the funding "A way of making Europe". The author Amal Bouich acknowledges MCIN for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033) .
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Development of a molecularly imprinted membrane for selective, high-sensitive, and on-site detection of antibiotics in waters and drugs: Application for sulfamethoxazole

  • El Hani, Ouarda
  • García Guzmán, Juan José
  • Palacios Santander, José María
  • Digua, Khalid
  • Amine, Aziz
  • Cubillana Aguilera, Laura
Sulfonamides are among the widespread bacterial antibiotics. Despite this, their quick emergence constitutes a serious problem for ecosystems and human health. Therefore, there is an increased interest in developing relevant detection method for antibiotics in different matrices. In this work, a straightforward, green, and cost-effective protocol was proposed for the preparation of a selective molecularly imprinted membrane (MIM) of sulfamethoxazole (SMX), a commonly used antibiotic. Thus, cellulose acetate was used as the functional polymer, while polyethylene glycol served as a pore-former. The developed MIM was successfully characterized through scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The MIM was used as a sensing platform in conjunction with a smartphone for optical readout, enabling on-site, selective, and highly sensitive detection of SMX. In this way, a satisfactory imprinting factor of around 3.6 and a limit of detection of 2 ng mL−1 were reached after applying response surface methodologies, including Box-Behnken and central composite designs. Besides, MIM demonstrated its applicability for the accurate and selective detection of SMX in river waters, wastewater, and drugs. Additionally, the MIM was shown to be a valuable sorbent in a solid-phase extraction protocol, employing a spin column setup that offered rapid and reproducible results. Furthermore, the developed sensing platform exhibited notable regeneration properties over multiple cycles and long shelf-life in different storage conditions. The newly developed methodology is of crucial importance to overcome the limitations of classical imprinting polymers. Furthermore, the smartphone-based platform was used to surpass the typically expensive and complicated methods of detection.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Evolutionary dynamics of the repeatome explains contrasting differences in genome sizes and hybrid and polyploid origins of grass loliinae lineages

  • Moreno-Aguilar, M.
  • Inda, L. A.
  • Sánchez-Rodríguez, A.
  • Arnelas, I.
  • Catalán, P.
The repeatome is composed of diverse families of repetitive DNA that keep signatures on the historical events that shaped the evolution of their hosting species. The cold seasonal Loliinae subtribe includes worldwide distributed taxa, some of which are the most important forage and lawn species (fescues and ray-grasses). The Loliinae are prone to hybridization and polyploidization. It has been observed a striking two-fold difference in genome size between the broad-leaved (BL) and fine-leaved (FL) Loliinae diploids and a general trend of genome reduction of some high polyploids. We have used genome skimming data to uncover the composition, abundance, and potential phylogenetic signal of repetitive elements across 47 representatives of the main Loliinae lineages. Independent and comparative analyses of repetitive sequences and of 5S rDNA loci were performed for all taxa under study and for four evolutionary Loliinae groups Loliinae, Broad-leaved (BL), Fine-leaved (FL), and Schedonorus lineages]. Our data showed that the proportion of the genome covered by the repeatome in the Loliinae species was relatively high (average ~ 51.8%), ranging from high percentages in some diploids (68.7%) to low percentages in some high-polyploids (30.7%), and that changes in their genome sizes were likely caused by gains or losses in their repeat elements. Ty3-gypsy Retand and Ty1-copia Angela retrotransposons were the most frequent repeat families in the Loliinae although the relatively more conservative Angela repeats presented the highest correlation of repeat content with genome size variation and the highest phylogenetic signal of the whole repeatome. By contrast, Athila retrotransposons presented evidence of recent proliferations almost exclusively in the Lolium clade. The repeatome evolutionary networks showed an overall topological congruence with the nuclear 35S rDNA phylogeny and a geographic-based structure for some lineages. The evolution of the Loliinae repeatome suggests a plausible scenario of recurrent allopolyploidizations followed by diploidizations that generated the large genome sizes of BL diploids as well as large genomic rearrangements in highly hybridogenous lineages that caused massive repeatome and genome contractions in the Schedonorus and Aulaxyper polyploids. Our study has contributed to disentangling the impact of the repeatome dynamics on the genome diversification and evolution of the Loliinae grasses. Copyright © 2022 Moreno-Aguilar, Inda, Sánchez-Rodríguez, Arnelas and Catalán.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Phylogenomics and Systematics of Overlooked Mesoamerican and South American Polyploid Broad-Leaved Festuca Grasses Differentiate F. sects. Glabricarpae and Ruprechtia and F. subgen. Asperifolia, Erosiflorae, Mallopetalon and Coironhuecu (subgen. nov.)

  • Moreno Aguilar, María Fernanda
  • Inda, Luís. A.
  • Sánchez Rodríguez, Aminael
  • Catalán, Pilar
  • Arnelas, Itziar
Allopolyploidy is considered a driver of diversity in subtribe Loliinae. We investigate the evolution and systematics of the poorly studied Mesoamerican and South American polyploid broad-leaved Festuca L. species of uncertain origin and unclear taxonomy. A taxonomic study of seven diagnostic morphological traits was conducted on a representation of 22 species. Phylogenomic analyses were performed on a representation of these supraspecific taxa and all other Loliinae lineages using separate data from the entire plastome, nuclear rDNA 45S and 5S genes, and repetitive DNA elements. F. subgen. Mallopetalon falls within the fine-leaved (FL) Loliinae clade, whereas the remaining taxa are nested within the broad-leaved (BL) Loliinae clade forming two separate Mexico–Central–South American (MCSAI, MCSAII) lineages. MCSAI includes representatives of F. sect. Glabricarpae and F. subgen. Asperifolia plus F. superba, and MCSAII of F. subgen. Erosiflorae and F. sect. Ruprechtia plus F. argentina. MCSAII likely had a BL Leucopoa paternal ancestor, MCSAI and MCSAII a BL Meso-South American maternal ancestor, and Mallopetalon FL, American I–II ancestors. Plastome vs. nuclear topological discordances corroborated the hybrid allopolyploid origins of these taxa, some of which probably originated from Northern Hemisphere ancestors. The observed data indicate rapid reticulate radiations in the Central–South American subcontinent. Our systematic study supports the reclassification of some studied taxa in different supraspecific Festuca ranks.
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Community Supported Agriculture (CSA) as resilient socio-economic structures: the role of collaboration and public policies in Brazil and Spain

  • González Azcárate, Mario|||0000-0001-9599-2564
  • Lara Silva, Vivian
  • Cruz Macein, José Luis
  • López García, Daniel|||0000-0003-2265-880X
  • Bardaji de Azcarate, Isabel|||0000-0002-6122-525X