Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Cement equivalence factor evaluations for fluid catalytic cracking catalyst residue

  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Velazquez Rodriguez, Sergio
Fluid catalytic cracking catalyst residue (FC3R) is a waste material that can be used as a Portland cement replacement in pastes, mortars, and concrete. The flow table results show that FC3R is a water demanding addition; nevertheless, this effect can be compensated with the use of superplasticizers. The pozzolanic activity of FC3R was studied observing the mechanical strength evolution with time. Pastes and mortars with FC3R incorporated show higher mechanical strengths than control specimens, indicating the pozzolanic activity of the waste. Cement equivalence factor (k-factor) evaluations were carried out. The k-factor values for the FC3R pastes and mortars were always greater than one, indicating that in order to maintain the same compressive mechanical strength of the control specimen it is sufficient to replace cement with a smaller amount of catalyst residue, due to the high pozzolanic activity of FC3R. There is a strong agreement between the k-factor values obtained in pastes and mortars., This work was supported by Ministerio de Ciencia y Tecnologia, Spain (Project MAT 2001-2694).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Pozzolanic Reaction Rate of Fluid Catalytic Cracking Residue (FC3R) in Cement Pastes

  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Velázquez Rodríguez, Sergio
Fluid catalytic cracking catalyst residue (FC3R) is a waste material generated in the petroleum industry. Previous research has shown that FC3R exhibits excellent pozzolanic properties in Portland cement mixtures. The pozzolanic activity of FC3R was studied by means of thermogravimetric analysis (measurement of lime fixation) and cold hydrochloric acid treatment (quantification of FC3R reacted). A water/binder ratio of 0.40 was used in the study in the preparation of a control paste (without spent catalyst) and a 15% substituted FC3R paste. The selected curing temperatures were 20 and 408C and several curing times were tested. The amount (grammes) of fixed lime by gramme of reacted catalyst indicated that approximately one part lime is chemically combined with 2.3 parts of spent catalyst. The combination of both study techniques allows determination of the optimal dosage in order to maximise use of this excellent pozzolan., This work was supported by Ministerio de Ciencia y Tecnologia, Spain (Project MAT 2001-2694). Sergio Velazquez would like to thank the Consejo Nacional de Ciencia y Tecnologia (CONACYT-Mexico).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of pozzolanic activity using methods based on the measurement of electrical conductivity of suspensions of portlnad cement and pozzolan

  • Velázquez Rodríguez, Sergio
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] The use of methods based on measuring electrical conductivity to assess pozzolanic activity has recently been used primarily in aqueous suspensions of pozzolan: calcium hydroxide. However, the use of similar methods in suspensions of cement with pozzolans has not been widely studied. This paper proposes a new method for rapid assessment of the pozzolanic activity of mineral admixtures in aqueous cement suspensions. In this study, the conditions for the application of the method were optimized, such as time, temperature, w/c ratio and dosage procedure. Finally, results are presented from the application of this method for characterizing the pozzolanic activity of the spent catalytic cracking catalyst. These results corroborate as previously reported, namely the high reactivity of this pozzolan obtained by other methods, such as thermogravimetry or evolution of the mechanical strength. In addition, the pozzolanic activity of the catalyst was compared with other pozzolans such as metakaolin and silica fume., This work was supported by Ministerio de Ciencia y Tecnologia, Spain (Project MAT 2001-2694). Sergio Velazquez would like to thank the Consejo Nacional de Ciencia y Tecnologia (CONACYT-Mexico).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High strength mortars using ordinary Portland cement-fly ash-fluid catalytic cracking ctalyst residue ternary system (OPC/FA/FCC)

  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
The use of ternary systems composed of ordinary Portland cement (OPC) and two pozzolanic mineral admixtures could supply several advantages in terms of the properties in both fresh and hardened states. Fly ash (FA) and spent fluid catalytic cracking catalyst (FCC) were combined to produce high strength mortars due to a synergic effect. OPC/FA systems (70%/30%) and OPC/FA/FCC systems (70%/20%/10%) were analyzed by thermogravimetric and SEM techniques. Mortars with different binder/sand ratios were prepared in order to yield high compressive strength values. On the one hand, fly ash particles act as nucleation sites that favour the hydration of Portland cement particles: at early stages (7 days), the calculated fixed hydrated lime values were negative, suggestive of a nucleating effect. For a longer curing period (90 days), the pozzolanic effect develops, as can be noted in terms of its compressive strength behaviour. The 90-days curing strength for OPC/FA mortars ranged between 96 and 98 MPa. In ternary mixtures (OPC/FA/FCC), FCC act as pozzolan during the initial 7 days period; the presence of fly ash particles favoured the presence of more portlandite by means of the nucleation effect. For longer curing times, fly ash particles also contribute to strength development, producing a synergic effect with FCC. The 90 days curing strength for OPC/FA/FCC mortars ranged between 103 and 106 MPa. Binary and ternary mortars reached strength activity index values equal or igher to the unit. Contributions to the strength (i.e. hydration of cement, the nucleation effect, and early and long term pozzolanic effects) have been calculated for 7 and 90 curing days pozzolan-containing mortars., This work was supported by Ministerio de Ciencia y Tecnologia, Spain (Project MAT 2001-2694). Thanks are given to the Electron Microscopy Service of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of the pozzolanic activity of spent FCC catalyst/fly ash mixtures in Portland cement pastes

  • Velázquez Rodríguez, Sergio
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
High pozzolanic activity of the residue spent catalytic cracking catalyst (FCC) has been reported by various authors in recent years. However, no report on the lime fixation of this residue when dosed together with other pozzolan has been developed, such material partially replacing Portland cement in the manufacture of hydraulic binders. One of the possibilities is to mixture it with fly ash (FA). This joint replacement provides several advantages in that: 1) Generation of FCC is low compared to other pozzolans including fly ash (FA); 2) The FCC tends to react to short curing times, while the FA does at longer times; 3) The FCC is demanding water, while the FA tends to improve the fluidity of the binder. This paper studies on cement pastes by thermogravimetric analysis of various mixed substitutions FCC:FA, varying the replacing percentage for FCC in the 0-15% range and for FA in the 0-30% range. Evolution of pastes was monitored by means of thermogravimetric analysis on pastes cured for 3-365 days. Products of the pozzolanic reaction were identified by SEM, being some of them cubic crystals (C3AH6 and/or hydrogarnet). By TGA analysis it was observed that when the %FCC is increased in the system, the amount of the calcium aluminate hydrates (C-A-H) and calcium aluminosilicate hydrates (C-A-S-H) also increased. Negative values of fixed lime were obtained due to an acceleration of the hydration of OPC, since the FA particles acted as nucleation sites for the precipitation of hydrated compounds. Fixed rates up to 90% of hydrated lime with substitutions as high as 45% in Portland cement system at one year of curing were reached. (C) 2016 Elsevier B.V. All rights reserved., This work was supported by Ministerio de Ciencia y Tecnologia, Spain (Project MAT 2001-2694).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Use of high-resolution thermogravimetric analysis (HRTG) technique in spent FCC catalyst/Portland cement pastes

  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Bonilla Salvador, María Mercedes
Thermogravimetric analysis is one of the most common instrumental techniques used for the characterization of pastes, mortars and concretes based on both calcium hydroxide and Portland cement. Important information about pozzolanic materials can be assessed concerning calcium hydroxide consumption and the formation of new hydrated products. Nevertheless, in some cases, problems associated with the overlapped decomposition processes for hydrates make the analysis of obtained data difficult. In this paper, the use of high-resolution thermogravimetric analysis, a powerful technique that allows separating decomposition processes in analysis of hydrated binders, was performed for spent FCC catalyst Portland cement pastes. These pastes were monitored for 1, 4, 8 h and 1, 2, 3, 7 and 28 curing days. In order to study the influence of the pozzolanic material (spent FCC catalyst), Portland cement replacements of 5, 15 and 30 % by mass were carried out. The presence of spent FCC catalyst in blended pastes modified the amount and the nature of the formed hydrates, mainly ettringite and stratlingite., This work was supported by the Ministry of Science and Technology, Spain (Project MAT 2001-2694).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An assessment of the pozzolanic activity of a spent catalyst from catalytic cracking using methods based on the measurement of the electrical conductivity and pH of suspensions with calcium hydroxide

  • Velázquez Rodríguez, Sergio
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] The pozzolanic activity of the spent catalyst produced by fluid catalytic cracking (FCC) has been studied by various methods in recent years. However, no quick and easy method has been reported for this activity based on the associated studies. In this work, the pozzolanic activity of a spent catalyst was investigated by measuring its electrical conductivity in aqueous suspensions of pozzolan/calcium hydroxide. The behavior of the FCC catalyst residue was compared to that of reactive and inert materials of similar chemical compositions. Further, the influence of temperature on the suspension was studied, and also, a new method was proposed in which the pozzolan/calcium hydroxide ratio was varied (with the initial presence of solid Ca(OH)2 in the system). It was concluded that the method is effective, fast and simple for evaluating the high reactivity of the catalyst. Therefore, this method is an alternative for the evaluation of the reactivity of pozzolanic materials., This work was supported by the Ministry of Science and Technology, Spain (Project MAT 2001-2694). Sergio Velazquez thanks the National Council for Science and Technology (Consejo Nacional de Ciencia y Tecnologia (CONACYT-Mexico)).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of silicoaluminous pozzolans on the hydration process of the Portland cement cured at low temperatures

  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Bonilla Salvador, María Mercedes
  • Tashima, Mauro M.
The aim of this paper is to study hydration processes in cement pastes and mortars, blended with either metakaolin (MK) or a catalyst used in catalytic cracking (FCC), and cured at low temperature. The amounts of hydrates and portlandite in pastes have been determined for 3¿28 days curing at 5¿20 C. Microstructural study, using thermogravimetric analysis of the pastes, has shown that FCC acts mainly as a pozzolan at low temperatures (5¿10 C), whereas MK also accelerates Portland cement hydration. Mechanical strengths of a control mortar, and mortars made with 15% replacement of cement by these two pozzolans, have been measured. Both mortars containing pozzolans exhibited a relative increase in compressive strength when cured at 5 C. A limestone filler (LF) has been used to compare the effects of adding inert or pozzolanic materials. Finally, mortars were prepared by partially replacing aggregates with either MK, FCC or LF. The MK and FCC are effective materials even for low curing temperatures, especially when they are used to replace a fraction of the aggregates in mortars, Authors thanks to Ministerio de Ciencia and Tecnologia of Spain the financial support of project MAT2001-2694 and FEDER funding.