Pasar al contenido principal

NANOESTRUCTURAS TENSIONADAS PARA CINTAS SUPERCONDUCTORAS DE YBCO DE BAJO COSTE Y PRESTACIONES ELEVADAS.: ANALISIS TERMICO AVANZADO

MAT2011-28874-C02-02

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT DE GIRONA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Solution design for low-fluorine trifluoroacetate route to YBa2Cu3O7 films

  • Palmer, X.
  • Pop, Cornelia
  • Eloussifi, Hichem
  • Roura Grabulosa, Pere
  • Farjas Silva, Jordi
  • Calleja, Albert
  • Palau, Anna
  • Obradors, Xavier
  • Puig Molina, Teresa
  • Ricart, Susagna
We present our work in the preparation of metallorganic precursor solutions with reduced fluorine content, able to fulfil the requirements for high-performance superconducting YBCO epitaxial layers as a promising approach to low cost and scalable coated conductors. Six different solutions using different quantities of fluorine and non-fluorine carboxylate precursors with a total amount of fluorine from 10 to 50% that of standard trifluoroacetic acid (TFA) solutions. For stabilization purposes different coordinating agents have been used and the solution rheology has been modified for proper substrate wettability. Thermal decomposition analysis and infrared spectroscopy performed directly in films, have revealed that the decomposition takes place in two consecutive stages around 265 and 310 °C respectively, and nuclear magnetic resonance (NMR) analysis could unveil the chemical reactions taking place in the solution. Using the solutions with 20% fluorine and upon optimization of the growth process parameters, YBCO layers with T c and J c(77 K) of 90 K and 4 MA cm−2 are obtained, The authors acknowledge the financial support from MICINN (Consolider NANOSELECT, CSD2007-00041, MAT 2011-28874-C02, MAT2014-51778-C2-2-R); Generalitat de Catalunya (Pla de Recerca 2014-SGR-753 and XaRMAE), and EU (FP7 NMP-LA-2012-280432 EUROTAPES project and MP1201 Cost action)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermoanalytical study of the decomposition of yttrium trifluoroacetate thin films

  • Eloussifi, Hichem
  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
  • Ricart, Susagna
  • Puig Molina, Teresa
  • Obradors, Xavier
  • Dammak, Mohamed
We present the use of the thermal analysis techniques to study yttrium trifluoroacetate thin films decomposition.In situ analysis was done by means of thermogravimetry, differential thermal analysis, and evolved gas analysis.Solid residues at different stages and the final product have been characterized by X-ray diffraction and scanning electron microscopy.The thermal decomposition of yttrium trifluoroacetate thin films results in the formation of yttria and presents the same succession of intermediates than powder's decomposition, however, yttria and all intermediates but YF3 appear at significantly lower temperatures.We also observe a dependence on the water partial pressure that was not observed in the decomposition of yttrium trifluoroacetate powders.Finally, a dependence on the substrate chemical composition is discerned, This work was partially funded by the Spanish Programa Nacional de Materiales through projects MAT2011-28874-C02-01 and MAT2011-28874-C02-02, by the Consolider program Nanoselect, CSD2007-00041, EU project EUROTAPES NMP3-LA-2012-280432 and by the Generalitat de Catalunya contract nos. 2009SGR-185 and 2009SGR-770
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal decomposition of barium trifluoroacetate thin films

  • Eloussifi, Hichem
  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
  • Ricart, Susagna
  • Puig Molina, Teresa
  • Obradors, Xavier
  • Dammak, Mohamed
The thermal decomposition of barium trifluoroacetate thin films under different atmospheres is presented. Thermogravimetry and evolved gas analysis have been used for this in situ analysis. We focus our attention on the different behavior exhibited by films when compared to powders. The decomposition of barium trifluoroacetate is altered due to the faster out-diffusion of the product reaction:CF2. After barium trifluoroacetate decomposition a stable intermediate, barium fluoride, is formed. The decomposition of barium fluoride is diffusion controlled and depends on water partial pressure, This work was partially funded by the Spanish Programa Nacional de Materiales through projects MAT2011-28874-C02-01 and MAT2011-28874-C02-02, by the Consolider program Nanoselect, CSD2007-00041, EU project NESPA-RTN and by the Generalitat de Catalunya contracts No. 2009SGR-185 and 2009SGR-770
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Determination of thermal conductivity of powders in different atmospheres by differential scanning calorimetry

  • Sánchez Rodríguez, Daniel
  • López-Olmedo, Joan Pere
  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
We have developed a new method to measure the thermal conductivity of powders by differential scanning calorimetry (DSC) that works with masses in amounts as low as tens of mg. The method is based on that used by Camirand to determine the thermal conductivity of materials in the form of thin sheets but introducing a hemispherical pan to contain powders in such a way that the issue of heat transfer is reduced to a one-dimensional problem. The modification of the method was successfully validated on obtaining identical results in determining the thermal conductivity of a commercial silicone with both Camirand"s method and the modified method. We have also tested our method with materials that, in bulk, cover a wide range of thermal conductivities and have performed the experiments with several atmospheres and reference metals. The results are consistent with already published general trends in that they confirm that thermal conductivity of powders is mainly governed by thermal conduction through the surrounding gas, This work was partially funded by the Spanish Programa Nacional de Materiales through projects MAT2011-28874-C02-02 and by the Generalitat de Catalunya contract No. 2009SGR-185
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal analysis of metal organic precursors for functional oxide preparation: thin films versus powders

  • Roura Grabulosa, Pere
  • Farjas Silva, Jordi
  • Eloussifi, Hichem
  • Carreras Blasco, Laura
  • Ricart, Susagna
  • Puig Molina, Teresa
  • Obradors, Xavier
The thermal decomposition of several metal organic precursors, used in the preparation of YBa2Cu3O7−x superconducting coated conductors (Cu acetate, Cu, Y and Ba trifluoroacetates and Ce propionate) is analyzed by means of several thermoanalytical techniques (TG/DTA, MS and DSC). In all cases, the metal organic precursors deposited as thin films decompose differently than powders from the same precursors. In thin films, decomposition is facilitated by the easier transport of reactive gas from the surrounding atmosphere and by the easier out-diffusion of volatile products. Consequently, films decompose at lower temperature and are more sensitive to the presence of any residual reactive gas in the furnace. Good thermal contact with the substrate is also shown to minimize overheating in films and avoid combustion processes that are otherwise often observed during the thermal decomposition of powders. Finally, the formation and stability of intermediate products towards the oxide formation, such as metal fluorides, differs in films because of the easier gas exchange. With respect to powders, these compounds are much less stable in films, where their decomposition temperature can be lowered by several hundreds of degrees Celsius. While in some cases the behaviour of films can be predicted by analyzing varying masses of precursor powders, this is not always the case. Therefore, thermal analysis carried out on films is recommended to avoid erroneous conclusions about materials preparation drawn from powders, We acknowledge the financial support from MICINN (MAT2011-28874-C02-01 and -02, Consolider Project NANOSELECT: CSD2007-00041), EU project EUROTAPES, (EUFP7 NMPLA2012280432) and by the Generalitat de Catalunya (Pla de Recerca 2009SGR-185, 2009-SGR-770 and XaRMAE). H. Eloussifi acknowledges financial support from the Tunisian Ministry of Higher Education and Scientific Research
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The effect of volatiles on the measurement of the reaction heat by differential scanning calorimetry

  • García Cano, Eduard
  • Sánchez Rodríguez, Daniel
  • López-Olmedo, Joan Pere
  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
When gases evolve during a chemical reaction, a fraction of the reaction heat is lost with them. We have analyzed, both theoretically and experimentally, the deviations that this effect can produce on the determination of the reaction heat by differential scanning calorimetry (DSC). It is shown that, even in the absence of gas overheating, deviations related to variations in the sample heat capacity can be substantial in experiments involving very intense DSC peaks. However, experiments performed on thermal decomposition of metal organic salts and on evaporation of liquids have shown that deviations usually arise from gas overheating, This work was partially funded by the Spanish Programa Nacional de Materiales through projects MAT2011-28874-C02-02 and by the Generalitat de Catalunya contract No. 2009SGR185
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Exact analytical solution for the Kissinger equation: Determination of the peak temperature and general properties of thermally activated transformations

  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
A key parameter of many transformations when heated at a constant rate is the peak temperature, i.e., the temperature at which the transformation rate is at its maximum. The most universal approach to determine the peak temperature for thermally activated transformations is the Kissinger equation. In this paper, we solve Kissinger equation to deduce the exact dependence of the peak temperature on the heating rate. This analytical solution is based on the Lambert W-function. In addition, an approximate solution is derived that is used to infer general properties of thermally activated processes and to obtain a test to check the validity of Kissinger method, This work was partially funded by the Spanish Programa Nacional de Materiales through project MAT2011-28874-C02-02 and by the Generalitat de Catalunya contract No. 2009SGR-185
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The thermal decomposition of barium trifluoroacetate

  • Farjas Silva, Jordi
  • Camps, Johan
  • Roura Grabulosa, Pere
  • Ricart, Susagna
  • Puig Molina, Teresa
  • Obradors, Xavier
A detailed analysis of the thermal decomposition of barium trifluoroacetate under different atmospheres is presented. Thermogravimetry, differential thermal analysis, and evolved gas analysis have been used for this in situ analysis. The presence of oxygen significantly advances the decomposition, while the presence of water vapor has a minor effect. The process is exothermic, the heat evolved being significantly larger in the presence of oxygen. The final product is BaF 2, which is stable up to 1200 °C. The underlying mechanism has been disclosed thanks to MS analysis of the volatiles formed during decomposition, This work was partially funded by the Spanish Programa National de Materiales through projects MAT2011-28874-C02-01 and MAT2011-28874-C02-02, by the Consolider program Nanoselect, CSD2007-00041, EU project NESPA-RTN and by the Generalitat de Catalunya contracts Nos. 2009SGR-185 and 2009SGR-770
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal analysis for low temperature synthesis of oxide thin films from chemical solutions

  • Sánchez Rodríguez, Daniel
  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
  • Ricart, Susagna
  • Mestres, Narcís
  • Obradors, Xavier
  • Puig Molina, Teresa
The possibility of synthesizing functional oxide thin films at low temperature via combustion synthesis is analyzed both experimentally and numerically. To this aim, the decomposition of several oxide precursors [copper and cerium acetates, yttrium trifluoroacetate, and In2O3 and La0.7Sr0.3MnO3 (LSMO) nitrate based precursors] has been analyzed by thermal analysis techniques. It is shown that, although these precursors decompose via combustion when they are in the form of powders, their corresponding films show no evidence of combustion. The reason for this different behavior is clearly revealed with numerical simulations. Thin films will hardly experience combustion because the precursor front extinguishes before reaching the precursor-substrate interface leaving a "cool zone" hundreds of micrometers thick. In contrast, it is argued that thin oxide films can be obtained at temperatures lower than powders because of the enhanced gas transport mechanisms that usually limit the decomposition rate, This work was partially funded by the Spanish Programa Nacional de Materiales through Projects MAT2011-28874-C02-01 and MAT2011-28874-C02-02, by the Consolider program Nanoselect, CSD2007-00041, and by the Generalitat de Catalunya Contract Nos. 2009SGR-185 and 2009SGR-770
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal gradients in thermal analysis experiments: Criterions to prevent inaccuracies when determining sample temperature and kinetic parameters

  • Sánchez Rodríguez, Daniel
  • Eloussifi, Hichem
  • Farjas Silva, Jordi
  • Roura Grabulosa, Pere
  • Dammak, Mohamed
Thermal analysis methods are customarily used to analyze the evolution of solid-state transformations when samples are submitted to a controlled temperature program. Thermal analysis results are generally interpreted under the assumption that no temperature gradients take place inside the sample, so that, under proper calibration the sample temperature can be determined and controlled. Two phenomena may contribute to the formation of temperature gradients within the sample: heat transport through the sample and heat evolved during an exothermic or endothermic transformation. We will provide two analytical relationships that relate the sample mass with the temperature gradient within the sample and that will provide a straightforward criterion for checking the reliability of the sample temperature. We will show that, because of their very low thermal conductivity, significant thermal gradients may occur in those samples in the form of powders. Besides, in the case of exothermic reactions and for typical experimental conditions, the heat released by the reaction significantly affects the determination of the sample temperature. Finally, we analyze how sample overheating affects the observed reaction kinetics, This work was partially funded by the Spanish Programa Nacional de Materiales through projects MAT2011-28874-C02-02 and by the Generalitat de Catalunya contract No. 2009SGR-185