Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of laser irradiation on failure mechanism of TiCp reinforcedtitanium composite coating produced by laser cladding

  • Candel Bou, Juan José
  • Jiménez, J.A.
  • Franconetti Rodríguez, Patricia
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser cladding is an effective technique to coat a metallic substrate with a layer of a different nature.It has been widely reported that the most important combined parameters controlling the quality ofthe coating are the specific energy (E) and the powder density ( ). In the present work, clad depositsof Ti6Al4V + 60 wt.% TiC were prepared on a Ti6Al4V substrate using an optimum combination of Ec= 24 J/mm2 and c= 3 mg/mm2. These experiments were performed using a laser power of 400 and600 W, in order to study the effect of laser power on the properties of the clad. The microstructure, phasecomposition and nanohardness of the coatings were investigated by optical microscopy, scanning elec-tron microscopy and X-ray diffraction. During laser processing, TiC can be partially converted to TiCX(X = 0.5) due mainly to the TiC dissolution into the laser-generated melting pool and subsequent precipi-tation during cooling. It was observed that the lower laser power limit reduces primary TiC dissolution butit also promotes secondary carbide alignment at the interface. On the other hand, the damage mechanisminduced by high laser power is dominated by primary TiC particle cracking by the high stress concentra-tion at the particle matrix interface followed by ductile failure of the matrix. It is also remarkable thatirradiance affects the TiC/TiCxratio despite Ecand care fixed and it determines hardness distributioninside the coating., Authors thank MINECO funding in special the Training of Research Staff programme with the help BES-2009-013589 and the support of the Comision Interministerial de Ciencia y Tecnologia (CICYT), Spain, under Grant MAT2012-39124. This work was developed at the Materials Technology Unit of the Polytechnic University of Valencia associated to CSIC through the National Centre for Metallurgical Research (CENIM). Finally, thank the EU for the funding received through the FEDER help in the project UPOV08-3E-005 for the purchase of equipment and the Generalitat Valenciana for the help ACOMP/2012/094.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The influence of temperature on the strain-hardening behavior of Fe-22/25/28Mn-3Al-3Si TRIP/TWIP steels

  • Pierce, D.T.
  • Benzing, J.T.
  • Jiménez, José Antonio
  • Hickel, T.
  • Bleskov, I.
  • Keum, J.
  • Raabe, D.
  • Raabe, D.
The influence of temperature and stacking fault energy (SFE) on the strain-hardening behavior and critical resolved shear stress for twinning was investigated for three Fe–22/25/28Mn–3Al–3Si wt.% transformation- and twinning-induced plasticity (TRIP/TWIP) steels. The SFEs were calculated by two different methods, density functional theory and statistical thermodynamic modeling. The dislocation structure, observed at low levels of plastic deformation, transitions from “planar” to “wavy” dislocation glide with an increase in temperature, Mn content, and/or SFE. The change in dislocation glide mechanisms from planar to wavy reduces the strain hardening rate, in part due to fewer planar obstacles and greater cross slip activity. In addition, the alloys exhibit a large decrease in strength and ductility with increasing temperature from 25 to 200 °C, attributed to a substantial reduction in the thermally activated component of the flow stress, predominate suppression of TRIP and TWIP, and a significant increase in the critical resolved shear stress for mechanical twinning. Interestingly, the increase in SFE with temperature had a rather minor influence on the critical resolved shear stress for mechanical twinning, and other temperature dependent factors which likely play a more dominant role are discussed., This work is sponsored by the National Science Foundation Division of Materials Research, USA, under grants DMR0805295 and DMR1309258, by the Ministry of Science and Innovation of Spain, under Grant MAT2012–39124, and under a Center for Nanophase Materials Science user proposal CNMS2014–291 at Oak Ridge National Laboratory. DTP gratefully acknowledges support for extended visits to CSIC, Madrid and MPI, Düsseldorf during his time as a graduate student at Vanderbilt University where most of this research was performed. The authors would also like to acknowledge Easo George and Josh Cicotte for reviewing the manuscript.