Pasar al contenido principal

EMISORES SELECTIVOS PARA CONVERSORES TERMOFOTOVOLTAICOS BASADOS EN MICROESTRUCTURAS EUTECTICAS

MAT2013-41045-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD DE ZARAGOZA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Solidification of NaCl–LiF–CaF2 ternary composites

  • Acosta, M. F.
  • Merino, R. I.
  • Ganschow, Steffen
  • Klimm, D.
The purpose of this work is to refine the microstructure of eutectic halides, candidates to polaritonic metamaterials, through the directional solidification of ternary compositions. NaCl–LiF–CaF2 ternary composites have been solidified using Bridgman and micro-pulling-down techniques at pulling rates from 3 to 300 mm/h for the first time. The interparticle spacing is 12% smaller for this composition than for the binary fibrous NaCl–LiF eutectic. Conditions for solidification and growth in order to generate ternary aligned microstructures are discussed. The very small amount of melt remaining in the mixtures until 580∘C is probably the consequence of solid solubility of LiCl in NaCl and the formation of the reciprocal salt pairs, as in NaCl–LiF. However, it does not prevent the solidification of homogenous ternary microstructures., Authors would like to acknowledge the financial support by EU under the Project NMP4-SL-2008-213669-ENSEMBLE and MAT2013-41045R. MFA acknowledges Ministerio de Educación, Cultura y Deporte (Spain) for the FPU scholarship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ceramics with photonic and optical applications, Cerámicas con aplicaciones ópticas y fotónicas

  • Orera, V. M.
  • Merino, R. I.
Open Access funded by Sociedad Española de Cerámica y Vidrio, under a Creative Commons license., [EN]: There is a fast growing interest in new applications for advanced ceramic systems in the field of functional materials and in particular for optical materials. Ceramics are entitled to fulfil the gap between glasses and single crystals in the area of photonic materials. The processing versatility and unpaired resistance to high temperature corrosive environments of some ceramics make them good candidates for such applications. However, the critical dependence of the material optical properties on microstructure makes the deep understanding of the processing conditions even more necessary than before for the fabrication of well ordered, transparent, efficient optical ceramics. This review is directed towards ceramists interested in new applications. In the paper we address some fundamental aspects of the relationship between processing, microstructure and optical properties that are illustrated with some examples related with transparent ceramics, glass ceramics, luminescence, random lasers, thermo-emissive applications, scintillators and dielectric metamaterials., [ES]: Existe un creciente interés en el desarrollo de nuevas aplicaciones basadas en cerámicas funcionales, en particular para aplicaciones como materiales ópticos. Los materiales cerámicos están destinados a cubrir el hueco entre los vidrios y los monocristales en el campo de los materiales fotónicos. La facilidad de procesado junto con su inigualable resistencia en medios corrosivos y de alta temperatura, hacen de las cerámicas buenos candidatos para ser utilizado en las aplicaciones ópticas. Sin embargo, las propiedades ópticas de un material, dependen muy fuertemente de su microestructura. Por ello la fabricación de cerámicas con microestructuras ordenadas, cerámicas transparentes y con eficientes propiedades ópticas requiere más que nunca, conocer profundamente las condiciones de procesado y de su influencia en la microestructura. Esta revisión está dirigida a ceramistas interesados en nuevas aplicaciones. En el artículo, tratamos brevemente algunos aspectos fundamentales de las relaciones entre procesado, microestructura y propiedades ópticas que hemos ilustrado con algunos ejemplos relacionados con las cerámicas transparentes, las vitrocerámicas, luminiscencia, láseres aleatorios, aplicaciones termoemisivas, centelleadores, y metamateriales dieléctricos., We want to thank MINECO (Spain) financing: MAT2012-30763 and MAT2013-41045-R programs., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Directionally solidified Al2O3-Yb3Al5O12 eutectics for selective emitters

  • Oliete, Patricia B.
  • Mesa, M. Cristina
  • Merino, R. I.
  • Orera, V. M.
Al2O3-Yb3Al5O12 eutectic rods were directionally solidified using the laser floating zone method at rates between 25 and 750 mm/h. The microstructure consisted of an interpenetrated network of both eutectic phases for all the growth rates. The size of the phases was strongly dependent on the growth rate, the eutectic interspacing decreasing from 4.5 μm at the lowest growth rate to 600 nm at 750 mm/h. The optical transmission of the sample with coarser microstructure was measured and compared with that of an Yb3Al5O12 single crystal grown >ad hoc> using the same method. The apparent >oscillator strength> of the single 2F7/2→2F5/2 Yb3+ absorption band was larger in the eutectic sample than in the single crystal, which was attributed to the increase in the light path caused by multiple refractions at the eutectic interphases. The thermal emission of the eutectic rod was studied between 1000 °C and 1500 °C. An intense and relatively narrow emission band at about 1 μm corresponding to the 2F5/2→2F7/2 Yb3+ electronic transition was observed in the whole temperature range. The intensity of the band increased with the temperature up to about 1300 °C. At higher temperatures a saturation of the selective emission was observed which was attributed to the competition between the increase in the thermal population of the excited state and the enhancement of the non-radiative de-excitation channels with the temperature., The authors gratefully acknowledge the financial support from the Ministerio de Economía y Competitividad de España under project MAT2013-41045-R and from the Centro Universitario de la Defensa de Zaragoza under project UZCUD2014-TEC-11., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Directionally solidified fabrication in planar geometry of Al2O3-Er3Al5O12 eutectic composite for thermophotovoltaic devices

  • Sola, D.
  • Oliete, Patricia B.
  • Peña, J. I.
In this work Al2O3–Er3Al5O12 eutectic composite was manufactured in planar geometry departing from eutectic particles both produced by directional solidification using a CO2 laser system at rates of 180 and 720 mm/h. Microstructure and mechanical properties were investigated as a function of the growth rate. Homogeneous and interpenetrated microstructure was found with phase size strongly dependent on the growth rate, decreasing when the processing rate was increased. Thermal emission of eutectic composites was studied in function of thermal excitation by using CO2 laser radiation as a heating source. An intense narrow emission band at 1.55 µm matching with the sensitive region of the InGaAs photoconverter and a low emission band at 1 µm were obtained. Features of thermal emission bands were correlated with collecting angle, microstructure and laser power, and compared to those obtained from departing eutectic particles., Authors gratefully acknowledge the financial support from the Ministerio de Economía y Competitividad de España under project MAT2013-41045-R. Dr. Daniel Sola also thanks the Bosch and Siemens Home Appliances Group for the financial support of his contract., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Selective thermal emission of directionally solidified Al2O3/Y3-xErxAl5O12 eutectics: Influence of the microstructure, temperature and erbium content

  • Oliete, Patricia B.
  • Orera, Alodia
  • Sanjuán, M. L.
  • Merino, R. I.
Directionally solidified eutectic rods of Al2O3-Y3−xErxAl5O12 (0 ≤ x ≤ 3) composition have been grown using the laser floating zone method at processing rates of 25 mm/h and 750 mm/h. For all the samples the microstructure presents the same morphology, consisting of an interpenetrated 3D eutectic network of both Al2O3 and garnet phases, while eutectic interspacing strongly depends on the solidification rate. Optical absorption, luminescence and thermal emission have been investigated as a function of the growth rate and the erbium content. From the luminescence characterization it can be concluded that erbium ions are present in the eutectic only in the garnet phase. Near infrared thermal emission has been measured at temperatures ranging from 1000 to 1500 °C. Selective emission consisting of an emission band at 1540 nm and a weaker line at 970 nm, ascribed to the radiative de-excitation of the thermally excited Er3+ ions from the 4I13/2 and 4I11/2 multiplets to the 4I15/2 ground state respectively, has been detected in all the samples containing erbium. The influence of the erbium content, the microstructure and the temperature on the thermal emission has been investigated. The strongest selective emission has been obtained for samples with x=3 although it does not increase proportionally to the erbium content. The thermal emission becomes more intense when the temperature is increased but the selective emission seems to saturate at temperatures higher than 1300 °C. This effect is especially noticeable for x=3 and is attributed to thermally activated non-radiative de-excitation channels. It is suggested that these channels become effective through energy transfer among Er3+ ions and towards killers., The authors gratefully acknowledge the financial support from the Ministerio de Economía y Competitividad de España under projects MAT2013-41045-R and MAT2016-77769-R., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of microstructural size on the thermal shock behavior of Al2O3-Er3Al5O12 directionally solidified eutectics

  • Nie, Ying
  • Oliete, Patricia B.
  • Merino, R. I.
We analyze the thermal shock resistance of directionally solidified eutectics. When quenching in water, the resistance starts to deteriorate with temperature differences in the range 260 to 300 K, almost independent of the microstructure size (or initial flexural strength). Unlike other strong, dense ceramics, the loss of strength is gradual upon quenching in boiling water. The onset of crack propagation seems to be controlled by the mismatch of the thermal and elastic properties of the component phases, while the length of the propagated cracks is limited by their quantity, which is estimated to scale approximately with the interface density., This work has been supported by the Spanish Ministerio de Economía, Industria y Competitividad (MINECO) and the CE (FEDER Funds) [grants number MAT2013-41045-R-EMITEME and MAT-2016-77769R-FLASCERAMAT]. Authors would like to acknowledge the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. Y. Nie would like to acknowledge the China Scholarship Council for a funding of Doctoral Joint-Training Program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Directionally solidified Ni doped MgO-MgSZ eutectic composites for thermophotovoltaic devices

  • Sola, D.
  • Oliete, Patricia B.
  • Merino, R. I.
  • Peña, J. I.
Ni-doped MgO-MgSZ eutectic composites were investigated as selective emitters for thermophotovoltaic devices. MgO-MgSZ:Ni eutectic rods were directionally solidified at 25 and 500 mm/h using the laser floating zone technique. Microstructure was strongly dependent on the growth rate, the size of the eutectic phases decreased as the growth rate increased. A hardness of ∼11 GPa and a fracture toughness of ∼1.6 MPa were obtained from indentation techniques, not showing dependence on the growth rate. Flexure strength increased from ∼400 MPa in samples grown at 25 mm/h up to ∼1 GPa for those solidified at 500 mm/h, which was attributed to the decrease of the phase size. Thermal emission of eutectic composites was studied up to 1400 °C. An intense broad emission band centred in 1.5 μm matching with the sensitive region of the GaSb photoconverter was found. The selective emission was ascribed to the de-excitation of the thermally excited Ni2+ ions., This work has been supported by the Spanish Ministerio de Economía Industria y Competitividad (MINECO) and the CE (FEDER Funds) [grants number MAT2013-41045-R-EMITEME and MAT-2016-77769R-FLASCERAMAT]. D. Sola thanks the PIT2 programme of the University of Murcia for the financial support of his contract., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Directionally solidified Al2O3-ME3Al5O12 (ME: Y, Er and Yb) eutectic coatings for thermophotovoltaic systems

  • Oliete, Patricia B.
  • López-Robledo, M. J.
  • Peña, J. I.
  • Silva-Treviño, J.
Selective emitters for thermophotovoltaic systems consisting of directionally solidified Al2O3-ME3Al5O12 (ME: Y, Er and Yb) eutectic coatings on Al2O3 substrates were produced and characterizated. Coatings were deposited by dip-coating on cylindrical substrates. After sintering, a continuous-wave CO2 laser was used to produce the surface resolidification. The optimization of the processing parameters yielded dense eutectic coatings with good adhesion to the substrate and with 90–200 µm in thickness. All coatings were free of voids and showed a eutectic microstructure consisting of a three dimensional interpenetrated network of Al2O3 and ME3Al5O12. The mechanical properties of the coatings (hardness and fracture toughness) were evaluated by indentation techniques. Thermal emission was studied by heating the rods with a CO2 laser at temperatures between 1000 and 1400 °C. Selective emission was observed in Er3+ and Yb3+ based coatings and attributed to the electronic transitions of the rare earth ions. Er3+-coatings showed the best emission properties as selective emitters for thermophotovoltaic converters., The authors gratefully acknowledge the financial support from the Ministerio de Economía y Competitividad de España under project MAT2013-41045-R and from the Centro Universitario de la Defensa de Zaragoza under project UZCUD2014-TEC-11., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Directionally solidified cobalt-doped MgO-MgAl2O4 eutectic composites for selective emitters

  • Merino, R. I.
  • Oliete, Patricia B.
  • Moshtaghioun, Bibi Malmal
  • Sola, Daniel
  • Peña, J. I.
This article belongs to the Special Issue Advanced Characterization of Functional Materials., Cobalt-doped MgO-MgAl2O4 eutectic composites were explored for their use as selective emitters for thermophotovoltaic devices. Eutectic ceramic rods with different cobalt content were directionally solidified by using the laser floating zone technique at two processing rates to obtain microstructures with different domain sizes. Thermal emission between 1000 °C and 1500 °C and optical properties (reflectance and transmittance) at room temperature were measured in the Co-doped composites and the effect on microstructure and cobalt content was investigated. Thermal emission consisted of an intense broad band at about 1.67 µm matching with the bandgap of the InGaAs cell. The emission was ascribed to the de-excitation from the 4T1(F) multiplet to the 4A2(F) ground state of the thermally excited Co ions located in the tetrahedral sites of the MgAl2O4 phase. The selectivity of the thermal emission showed a decrease with the cobalt content due to the enhancement of other electronic transitions, which leads to keeping the cobalt content in these composites at low levels (<0.15% at Co) for their use as selective emitters., This research was funded by the Spanish Ministerio de Economía, Industria y Competitividad (MINECO) and the CE (FEDER FUNDS), grants number MAT2013-41045-R-EMITEME and MAT-2016-77769R-FLASCERAMAT. The Departamento de Ciencia, Universidad y Sociedad del Conocimiento del Gobierno de Aragón also contributed through the financial support to the Research Group T02-20R. B.M.M. wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva- Incorporación” fellowship during her sabbatical stay in Zaragoza. D.S. thanks the PIT2 program of the University of Murcia´s own research plan., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ceramics with photonic and optical applications

  • Orera, Víctor M.
  • Merino, Rosa I.
There is a fast growing interest in new applications for advanced ceramic systems in the field of functional materials and in particular for optical materials. Ceramics are entitled to fulfil the gap between glasses and single crystals in the area of photonic materials. The processing versatility and unpaired resistance to high temperature corrosive environments of some ceramics make them good candidates for such applications. However, the critical dependence of the material optical properties on microstructure makes the deep understanding of the processing conditions even more necessary than before for the fabrication of well ordered, transparent, efficient optical ceramics. This review is directed towards ceramists interested in new applications. In the paper we address some fundamental aspects of the relationship between processing, microstructure and optical properties that are illustrated with some examples related with transparent ceramics, glass ceramics, luminescence, random lasers, thermo-emissive applications, scintillators and dielectric metamaterials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Directionally solidified fabrication in planar geometry of Al2O3-Er3Al5O12 eutectic composite for thermophotovoltaic devices

  • Sola, D.
  • Oliete, P.B.
  • Peña, J.I.
In this work Al2O3-Er3Al5O12 eutectic composite was manufactured in planar geometry departing from eutectic particles both produced by directional solidification using a CO2 laser system at rates of 180 and 720 mm/h. Microstructure and mechanical properties were investigated as a function of the growth rate. Homogeneous and interpenetrated microstructure was found with phase size strongly dependent on the growth rate, decreasing when the processing rate was increased. Thermal emission of eutectic composites was studied in function of thermal excitation by using CO2 laser radiation as a heating source. An intense narrow emission band at 1.55 µm matching with the sensitive region of the InGaAs photoconverter and a low emission band at 1 µm were obtained. Features of thermal emission bands were correlated with collecting angle, microstructure and laser power, and compared to those obtained from departing eutectic particles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Directionally solidified Al2O3-Yb3Al5O12 eutectics for selective emitters

  • Oliete, P. B.
  • Mesa, M. C.
  • Merino, R. I.
  • Orera, V. M.
Al2O3-Yb3Al5O12 eutectic rods were directionally solidified using the laser floating zone method at rates between 25 and 750 mm/h. The microstructure consisted of an interpenetrated network of both eutectic phases for all the growth rates. The size of the phases was strongly dependent on the growth rate, the eutectic interspacing decreasing from 4.5 µm at the lowest growth rate to 600 nm at 750 mm/h. The optical transmission of the sample with coarser microstructure was measured and compared with that of an Yb3Al5O12 single crystal grown "ad hoc" using the same method. The apparent "oscillator strength" of the single 2F7/2¿2F5/2 Yb3+ absorption band was larger in the eutectic sample than in the single crystal, which was attributed to the increase in the light path caused by multiple refractions at the eutectic interphases. The thermal emission of the eutectic rod was studied between 1000 °C and 1500 °C. An intense and relatively narrow emission band at about 1 µm corresponding to the 2F5/2¿2F7/2 Yb3+ electronic transition was observed in the whole temperature range. The intensity of the band increased with the temperature up to about 1300 °C. At higher temperatures a saturation of the selective emission was observed which was attributed to the competition between the increase in the thermal population of the excited state and the enhancement of the non-radiative de-excitation channels with the temperature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Directionally solidified Al2O3-ME3Al5O12 (ME: Y, Er and Yb) eutectic coatings for thermophotovoltaic systems

  • Oliete, Patricia B.
  • López-Robledo, Manuel J.
  • Peña, José I.
  • Silva, Jorge
Selective emitters for thermophotovoltaic systems consisting of directionally solidified Al2O3-ME3Al5O12 (ME: Y, Er and Yb) eutectic coatings on Al2O3 substrates were produced and characterizated. Coatings were deposited by dip-coating on cylindrical substrates. After sintering, a continuous-wave CO2 laser was used to produce the surface resolidification. The optimization of the processing parameters yielded dense eutectic coatings with good adhesion to the substrate and with 90–200 µm in thickness. All coatings were free of voids and showed a eutectic microstructure consisting of a three dimensional interpenetrated network of Al2O3 and ME3Al5O12. The mechanical properties of the coatings (hardness and fracture toughness) were evaluated by indentation techniques. Thermal emission was studied by heating the rods with a CO2 laser at temperatures between 1000 and 1400 °C. Selective emission was observed in Er3+ and Yb3+ based coatings and attributed to the electronic transitions of the rare earth ions. Er3+-coatings showed the best emission properties as selective emitters for thermophotovoltaic converters.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Selective thermal emission of directionally solidified Al2O3/Y3-xErxAl5O12 eutectics: influence of the microstructure, temperature and erbium content

  • Oliete, P. B.
  • Orera, A.
  • Sanjuán, M. L.
  • Merino, R. I.
Directionally solidified eutectic rods of Al2O3-Y3-xErxAl5O12 (0 = x = 3) composition have been grown using the laser floating zone method at processing rates of 25 mm/h and 750 mm/h. For all the samples the microstructure presents the same morphology, consisting of an interpenetrated 3D eutectic network of both Al2O3 and garnet phases, while eutectic interspacing strongly depends on the solidification rate. Optical absorption, luminescence and thermal emission have been investigated as a function of the growth rate and the erbium content. From the luminescence characterization it can be concluded that erbium ions are present in the eutectic only in the garnet phase. Near infrared thermal emission has been measured at temperatures ranging from 1000 to 1500 °C. Selective emission consisting of an emission band at 1540 nm and a weaker line at 970 nm, ascribed to the radiative de-excitation of the thermally excited Er3+ ions from the 4I13/2 and 4I11/2 multiplets to the 4I15/2 ground state respectively, has been detected in all the samples containing erbium. The influence of the erbium content, the microstructure and the temperature on the thermal emission has been investigated. The strongest selective emission has been obtained for samples with x=3 although it does not increase proportionally to the erbium content. The thermal emission becomes more intense when the temperature is increased but the selective emission seems to saturate at temperatures higher than 1300 °C. This effect is especially noticeable for x=3 and is attributed to thermally activated non-radiative de-excitation channels. It is suggested that these channels become effective through energy transfer among Er3+ ions and towards killers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Influence of microstructural size on the thermal shock behavior of Al2O3-Er3Al5O12 directionally solidified eutectics

  • Nie, Y.
  • Oliete, P.B.
  • Merino, R.I.
We analyze the thermal shock resistance of directionally solidified eutectics. When quenching in water, the resistance starts to deteriorate with temperature differences in the range 260 to 300 K, almost independent of the microstructure size (or initial flexural strength). Unlike other strong, dense ceramics, the loss of strength is gradual upon quenching in boiling water. The onset of crack propagation seems to be controlled by the mismatch of the thermal and elastic properties of the component phases, while the length of the propagated cracks is limited by their quantity, which is estimated to scale approximately with the interface density.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Directionally solidified Ni doped MgO-MgSZ eutectic composites for thermophotovoltaic devices

  • Sola, D.
  • Oliete, P.B.
  • Peña, J. I.
  • Merino, R.I.
Ni-doped MgO-MgSZ eutectic composites were investigated as selective emitters for thermophotovoltaic devices. MgO-MgSZ:Ni eutectic rods were directionally solidified at 25 and 500 mm/h using the laser floating zone technique. Microstructure was strongly dependent on the growth rate, the size of the eutectic phases decreased as the growth rate increased. A hardness of ~11 GPa and a fracture toughness of ~1.6 MPa were obtained from indentation techniques, not showing dependence on the growth rate. Flexure strength increased from ~400 MPa in samples grown at 25 mm/h up to ~1 GPa for those solidified at 500 mm/h, which was attributed to the decrease of the phase size. Thermal emission of eutectic composites was studied up to 1400 °C. An intense broad emission band centred in 1.5 µm matching with the sensitive region of the GaSb photoconverter was found. The selective emission was ascribed to the de-excitation of the thermally excited Ni2+ ions.