Pasar al contenido principal

ELECTRODOS Y ELECTROLITOS PARA ALMACENAMIENTO Y PRODUCCION EFICIENTES DE ENERGIA: BATERIAS Y PILAS DE COMBUSTIBLE

MAT2013-46452-C4-3-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD CARLOS III DE MADRID
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-performance Ni-YSZ thin-walled microtubes for anode-supported solid oxide fuel cells obtained by powder extrusion moulding

  • Arias, B. I.
  • Sotomayor Lozano, María Eugenia
  • Várez, A.
  • Levenfeld, Belén
  • Monzón, Hernán
  • Laguna-Bercero, M. A.
  • Larrea, Ángel
Aiming at the fabrication of microtubular anode-supports for Solid Oxide Fuel Cell (SOFC) applications, this contribution deals with the production of Ni-YSZ thin-walled tubes (<1 mm thickness) via Powder Extrusion Moulding (PEM). The overall method has been optimized with an emphasis on the effect of NiO particle size using two commercial NiO powders with mean sizes of 0.7 and 8 μm. A thermoplastic binder system based on polypropylene (PP), paraffin wax (PW) and stearic acid (SA) in volume ratios of 50, 46 and 4, respectively, was used along with corn starch as a pore forming agent. Different feedstocks with solid loadings varying from 45 to 65 vol% were processed and characterized to determine the optimal formulation. Typically, the mixtures exhibited a pseudoplastic behaviour from 100 to 1000 s. Feedstocks with finer NiO particles had the most balanced properties for PEM purposes and an optimal powder volume content of 65 vol% was established. After extrusion and debinding steps, defect-free and constant cross-section tubes with 15 mm of length and 4 mm of nominal diameter were obtained. The final microstructure and DC conductivity were found to be closely linked to the NiO particle size, yielding a higher degree of open porosity and a better performance when using finer NiO powder. Based on this study, the packing mechanism was found to be likely limited by the contribution of steric hindrances when dissimilar and coarse powders are mixed, which may play a decisive role in order to set tailored formulations., Authors would like to thank financial support received from MICINN and Feder program of the European Community (MAT2013-46452-C4-3R and MAT2012-30763 projects), and Madrid regional government (MATERYENER3CM S2013/MIT-2753 Program)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

DABCO-functionalized polysulfones as anion-exchange membranes for fuel cell applications: Effect of crosslinking

  • Pérez-Prior, Teresa
  • Ureña, Nieves
  • Tannenberg, M.
  • Río, Carmen del
  • Levenfeld, Belén
A series of DABCO-functionalized polysulfones were synthesized and characterized. The effect that crosslinking has on the membrane properties containing different degrees of functionalization was evaluated. These polymers showed good thermal stability below the fuel cell operation temperature, T < 100 °C, reflected by the T, T, and thermal durability. The water uptake increased as the percentage of DABCO groups increased and the crosslinked membranes showed lower capacity to absorb water than the non-crosslinked ones favoring thus the dimensional stability of the first ones. Membranes in the chloride form containing low degree of functionalization exhibited the highest tensile strength values. The ionic conductivity of non-crosslinked membranes varied as a function of the functionalization degree until a value of around 100% achieving a maximum value at 86%. However, the crosslinked ones showed satisfactory ionic conductivities for values higher than 100%. The behavior of these polymeric materials in alkaline solutions revealed a great alkaline stability necessary to be used as solid electrolytes in fuel cells. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017, 55, 1326–1336., We thank Professor Alejandro Varez for fruitful discussion. This work has been supported by the Projects MATERYENER3CM S2013/MIT-2753 of Comunidad de Madrid, MAT2013-46452- C4-3R of MINECO (Spanish Government), and S2013/MAE- 2975 PILCONAER of Comunidad de Madrid and European Social Fund (ESF)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Aqueous and non-aqueous Li+/H+ ion exchange in Li0.44La0.52TiO3 perovskite

  • Durán, Teresa
  • Climent-Pascual, Esteban
  • Pérez-Prior, Maria T.
  • Levenfeld, Belén
  • Varez, Alejandro
  • Sobrados, Isabel
  • Sanz Lázaro, Jesús
The topotactic Li/H exchange in LiLaTiO has been studied in different aqueous and non-aqueous media with different acidity. With this purpose, aqueous hydrochloric and nitric acid solutions and benzoic acid/ethanol solution were employed. The pristine and exchanged samples have been characterized by H and Li MAS-NMR, TGA and XRD techniques. Aqueous hydrochloric and nitric acid solutions produce the powders degradation and the subsequent formation of LiTiO and LaTiO phases. A detailed analysis of the H MAS NMR spectra of exchanged samples indicate that Li/H exchange reaction in pure water produced formation of LiOH at the particles surface, band at 0 ppm, that could subsequently carbonated after exposition in air. Furthermore the presence of other OH signals at 8, 6 and 2 ppm has been related to differences on octahedral Ti-O distances, produced by La/vacancy ordering in alternating planes of perovskites. In samples immersed into benzoic acid/ethanol solution results are similar, however the amount of LiOH species in particle surface is considerable lower. The exchange degree improved when increasing exchange temperature. The mechanical grinding of powders decreases the particle size improving exchange reactions; however, grinding treatments eliminated specific NMR bands of perovskite. In ground materials new H NMR bands at 6 and 4 ppm were ascribed to an amorphous phase., This work has been supported by Projects funded by the Regional Government (Comunidad de Madrid through MATERYENER3 CM S2013/MIT-2753) and the Spanish Government, (MICINN through MAT2013-46452-C4-3R Project). The authors also thank the European Programme-IRSES (NANOLICOM) for financial support.