Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The role of crosslinking on the physical properties of gelatin based films

  • Chaibi, S.
  • Benachour, D.
  • Merbah, M.
  • Esperanza Cagiao, M.
  • Baltá Calleja, Francisco José
12 págs.; 7 figs.; 4 tabs., © 2015, Springer-Verlag Berlin Heidelberg. The crosslinking of gelatin using crosslinking agents based on condensation of the aldehyde groups and ε-amine groups present in lysine and hydroxylysine rests is a very attractive method reported recently. The present work deals with different films prepared from commercial gelatin of type B and animal origin, aiming at an improvement of physical properties. These films were modified by two plasticizing agents (glycerol, GLY, and poly (vinyl alcohol), PVA) and/or crosslinked by glutaraldehyde (GTA). The number of ε-amino groups present in the gelatin chains, before and after modification, was determined by the method of protein dosage using 2,4,6-trinitro benzene sulfonic acid (TNBS). The addition of the plasticizing and/or crosslinking agents induced a decrease in the number of ε-amino-groups due to the fact that these groups are involved in the physical and/or chemical crosslinking reactions occurring among the different components. The variation of the crosslinking ratio was studied as a function of formulation type, crosslinking nature and GTA concentration. The use of microhardness (H) in this study emphasizes the effect of the crosslinking on the improvement of the micromechanical properties. The study of differential scanning calorimetry reveals that crosslinking induces a drastic decrease of crystallinity in the samples., FJBC gratefully acknowledges the MINECO, Spain (grant MAT 2013–47898-C2-1-R) for the generous support of this work., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Local mechanical properties of graphene/polyethylene-based nanocomposites by depth-sensing indentation

  • Flores, Araceli
  • Ania, F.
  • Salavagione, Horacio J.
  • Ellis, Gary James
  • Saurel, Damien
  • Gómez-Fatou, Marián A.
Local mechanical properties of modified-graphene high-density polyethylene nanocomposites are investigated using depth-sensing indentation. Three different chemical routes are employed to boost filler dispersion by functionalizing graphene with polyethylene brushes and incorporating a small amount of free short-chain polyethylene. At large penetration depths the results reveal distinct mechanical properties for the different chemical approaches. Hardness, modulus and creep resistance are discussed in terms of filler dispersion, polymer nanostructure and plasticization of the amorphous regions by the short-chain polyethylene. By reducing the indentation size, maps of the surface mechanical properties are generated, and graphene agglomerates that appear in some nanocomposites can be clearly identified. However, these agglomerates present significantly inferior mechanical properties than those usually reported for graphene, and results at the nanoscale suggest that modification of graphene together with the viscous >liquid-like> character of the polymer host represent strong impediments for effective reinforcement. Notwithstanding, one of the nanocomposites (from the thiol-ene click reaction) overcomes these issues, achieving a macroscopic mechanical performance similar to that of the neat polymer, combined with outstanding electrical conductivity., The authors wish to thank the MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under Grants MAT2013-47898-C2-1-R and MAT2013-47898-C2-2-R. HJS would like to acknowledge the MICINN for a ‘Ramón y Cajal’ Senior Research Fellowship. WAXS measurements were carried out with financial support from the Comunidad de Madrid, Spain, BIPEDD-2: S2010-BMD-2457. The authors wish to thank Dr. Pilar Posadas and Mr. David Gómez of the Characterization Service of the Institute of Polymer Science & Technology, CSIC, for the AFM and SEM measurements, respectively, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mapping the Mechanical Properties of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Banded Spherulites by Nanoindentation

  • Enrique-Jiménez, Patricia
  • Vega, Juan Francisco
  • Martínez-Salazar, Javier
  • Ania, F.
  • Flores, Araceli
Nanoindentation provides clear evidence that spherulite banding can be associated with a continuous modulation of mechanical properties from the more compliant peaks to the stiffer valleys. The structural arrangement in polymer-banded spherulites has intrigued scientists for many decades, and the debate has been recently intensified with the advent of new experimental evidence. The present paper approaches this issue by exploring the local mechanical properties of poly(3-hydroxybutyrate-co-3-hydroxyvalerate)-ringed spherulites via nanoindentation and discussing the confidence of the results. It was found that storage modulus and hardness across the banding morphology can be described as a sequence of regular oscillations with a periodicity that exactly matches the one observed using optical and atomic force microscopy. Results are consistent with the model of regular twisting of the lamellae, with flat-on arrangement in the low regions and edge-on lamellae in the crests., The authors wish to thank the MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R (covering the costs to publish in open access) and MAT2012-36341. Patricia Enrique-Jimenez acknowledges MINECO for a FPI (Formación Personal Investigador) studentship. We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Advanced Elastomeric Conductive Nanocomposites by Selective Chemical Affinity of Modified Graphene

  • Salavagione, Horacio J.
  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Martínez, Gerardo
  • Ania, F.
  • Flores, Araceli
  • Gómez-Fatou, Marián A.
9 págs.; 8 figs.; 3 tabs., The preparation of conductive nanocomposites of poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS) triblock copolymers with chemically modified graphene is reported. Graphene has been functionalized with short polyethylene brushes by thiol-ene click chemistry in order to enhance the interactions of the filler with the ethylenic phase of the block copolymer. The presence of graphene modifies the morphology of the SEBS domains, reducing their size and promoting an isotropic distribution of cylinders arranged in hexagonal packing, as shown by SAXS, AFM, and TEM. The elastomeric character of SEBS persists in the nanocomposites with filler content below 1 vol %, retaining high elongation at break. In addition, the percolation threshold for electrical conductivity is found to be slightly above 0.7 vol %, reaching conductivity values of ∼10 S cm for ∼2.5 vol % of filler. These materials represent a new class of flexible conductors that open promising opportunities for applications like actuators or bodily motion sensors. Copyright © 2016 American Chemical Society, Financial support from MINECO (Ministerio de Economiá y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R and MAT2013-47898- C2-2-R is gratefully acknowledged. H.J.S. acknowledges the MINECO for a “Ramón y Cajal” Senior Research Fellowship, and P.E.-J. and S.Q.-D. acknowledge a FPI Fellowship., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The Role of the Compatibilizer on the Microindentation Hardness of iPP/PC Blends

  • Hellati, A.
  • Douibi, A.
  • Boufassa, S.
  • Benavente, Rosario
  • Benachour, D.
  • Baltá Calleja, Francisco José
8 pags., 9 figs., 3 tabs., Blends of isotactic polypropylene (iPP) and polycarbonate (PC) with and without a compatibilizer were prepared using a Brabender Haake Rheocord at 2608C and 32 rpm. Maleic anhydride rafted styrene-ethylene/butylene-styrene (SEBS-g-MAH) and maleic anhydride grafted ethylene¿ propylene diene (EPDM-g-MAH) were chosen as compatibilizers and their proportion was set to 5, 10, and 15 wt%, respectively. The thermal properties and crystallization behavior were determined by differential scanning calorimetry (DSC) and wide angle X-ray scattering (WAXS). Micromechanical properties were also investigated using a Vickers microindentation tester. The DSC analysis indicates that the melting temperature of iPP in the all the blends, compatibilized and uncompatibilized ones, remains constant and is almost the same as those of the pure component. On the other hand, it is shown that the degree of crystallinity of iPP in the blends calculated by DSC and WAXS is dependent of the composition of the polymeric mixture. However the hardness (H) decreases with increasing PC content until the composition of iPP/PC (75/25) is reached, whereas for larger PC content values, H increases. The same trend was obtained with the addition of both compatibilizers. VC 2016 Society of Plastics Engineers, The authors are grateful for the financial support of the MINECO, Spain (Projects MAT2013 -47898-C2-1-R and MAT2013-47972-C2-1-P). A. H. greatly thanks the University of Borj Bou Arreridj for covering his expenses during his stay in Madrid., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Control of the structure and properties of SEBS nanocomposites via chemical modification of graphene with polymer brushes

  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Salavagione, Horacio J.
  • Wesner, D.
  • Schönherr, H.
  • González-Casablanca, Jesús
  • García-Quismondo, Roberto
  • Martínez, Gerardo
  • Gómez-Fatou, Marián A.
  • Ania, F.
  • Flores, Araceli
Incorporation of small quantities of graphene modified with polystyrene brushes into poly (styrene-b-ethylene-co-butylene-b-styrene) (SEBS) produces elastomeric conductive nanocomposites with enhanced electromechanical behaviour. Compared to graphene modified with polyethylene rubbery brushes, polystyrene-modified graphene distorts the hexagonal packing of cylinders in SEBS to a lesser extent due to the selective interactions with the rigid polystyrene blocks. At the same time, the type of filler has an apparent impact in the nano-, macro- and electro-mechanical properties of the nanocomposites. Consistently, AFM nanoindentation shows a narrower distribution of modulus values for the polystyrene modification. Moreover, tensile testing reveals that only the nanocomposites with styrene-affine fillers show elongation at break comparable to SEBS. Most importantly, a stable electromechanical behaviour is only found for the polystyrene modification, which is attributed to the selective interaction of the brushes on graphene with the polystyrene blocks of the matrix. The work offers a comprehensive understanding of the interplay between the nature of the polymer brush grafted to graphene, the nanostructure of the nanocomposites and their final properties., The SAXS experiments were performed at BL11 beamline at ALBA Synchrotron with the collaboration of ALBA staff.Funding Fig. 11. Electromechanical tests. Resistance change as a response to cyclic strain for 2gpsSEBS (a, c) and 2gpeSEBS (b, d). P. Enrique-Jimenez et al. European Polymer Journal 97 (2017) 1–13 11 sources Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R, MAT2013-47898-C2-2-R is gratefully acknowledged. PEJ and SQ also acknowledge the MINECO for a FPI Fellowship. PEJ additionally thanks the MINECO for a grant under the Predoctoral Mobility Program (EEBB-I-16-10848). This work was also supported by the European Research Council (ERC project ASMIDIAS, Grant no. 279202), the Deutsche Forschungsgemeinschaft (DFG grant no. INST 221/87-1 FUGG) and the University of Siegen., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the chemical functionalization of graphene on the properties of polypropylene-based nanocomposites

  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Papageorgiou, D. G.
  • Ania, F.
  • Flores, Araceli
  • Kinloch, I. A.
  • Gómez-Fatou, Marián A.
  • Young, R. J.
  • Salavagione, Horacio J.
9 pags., 5 figs., 4 tabs., Nanocomposites of polypropylene were prepared with different loadings of both commercially-available graphene and graphene that had been modified with low molecular weight polypropylene brushes. The dependence of the thermal stability, electrical conductivity and mechanical properties of the composites on the type and loading of graphene have been investigated. The mechanical properties were studied using several techniques, including nanoindentation, four-point bending coupled to Raman spectroscopy and tensile testing. Significant differences on the mechanical performance, due to the influence of graphene content and modification, have been observed; i.e. the Young's modulus takes values up to 30% higher for nanocomposites with modified graphene, compared to those with pristine graphene. Different trends on the variation of mechanical properties have been encountered at the local and macro scales and a discussion of the respective results from the different techniques is offered. Finally, the behavioral changes on the electrical conductivity are also discussed., Financial support by MINECO, Spain (Grants MAT2013-47898- C2-1-R and MAT2013-47898-C2-2-R) is gratefully acknowledged. S.Q.-D. and P.E.-J. acknowledge a FPI Fellowship. D.G.P, I.A.K and R.J.Y acknowledge funding from the European Union Seventh Framework Programme under grant agreement no 604391, Graphene Flagship., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructure and morphology of poly(vinylidene fluoride)/polymethyl (methacrylate)/clay nanocomposites: correlation to micromechanical properties

  • Zouai, F.
  • Benabid, F. Z.
  • Bouhelal, S.
  • Cagiao, M. E.
  • Benachour, D.
  • Baltá Calleja, Francisco José
11 pags., 7 figs., 2 tabs., Nanocomposites based on poly(vinylidene fluoride) (PVDF)/poly(methyl methacrylate) (PMMA) with untreated clay were prepared in one step by reactive melt extrusion. Chemical reactions took place between the polymer matrices, the inorganic clay particles, and three reactive agents, leading to the PVDF/PMMA/clay nanocomposites. The microstructure characterizations were carried out by differential scanning calorimetry and wide-angle X-ray scattering (WAXS). The mechanical behavior was investigated by tensile experiments, impact tests, and microhardness measurements. The morphological characterization was carried out by optical and atomic force microscopy (AFM). The decrease of the melting and crystallization temperatures of the PVDF with the increasing PMMA content is attributed to the interactions between the oxygen of the PMMA carbonyl group and the PVDF’s hydrogen atom. WAXS analysis shows that there is neither an intercalation step nor total exfoliation in any composition. As the PMMA content increases, WAXS diagrams show either the PVDF α-crystallographic form, both, α- and β-forms, or only the β-form. For PMMA contents higher than 40 wt%, the materials became amorphous. The microhardness of the samples decrease for a PMMA content up to 20 wt%. The study by optical microscopy and AFM illustrates the significant effect in the presence of clay on the film’s surface morphology., FJBC gratefully acknowledges the MINECO, Spain (Grant MAT 2013–47898-C2-1-R) for the generous support of this work., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Estudio del bandeado en esferulitas poliméricas mediante nanoindentación

  • Enrique-Jiménez, Patricia
  • Vega, Juan Francisco
  • Martínez-Salazar, Javier
  • Ania, F.
  • Flores, Araceli
6 pags., 5 figs., La nanoindentación instrumentada dinámica es una técnica muy valiosa para medir propiedades mecánicas de materiales a escala submicrométrica, que permite obtener un perfil en función de la penetración en la superficie del material. Además, la mayor ventaja que ofrece la nanoindentación es su capacidad para caracterizar pequeños volúmenes de muestras con gran resolución espacial. Dicha capacidad se ha aplicado en este trabajo para abordar el estudio del bandeado esferulítico de poli(3-hidroxibutirato-co-3-hidroxivalerato) (P3HB-co-3HV). La estructura asociada a esta morfología ha sido objeto de controversia durante décadas, y este debate se ha intensificado recientemente con la aparición de nuevas evidencias experimentales. El estudio mediante nanoindentación se ha complementado con medidas de microscopía de fuerzas atómicas (AFM), concluyéndose que las esferulitas están formadas por valles y crestas, tanto mecánicos como morfológicos. Los resultados apoyan un modelo de plegamiento regular y continuo de las laminillas desde el centro de las esferulitas hacia el exterior, Los autores quieren agradecer al MINECO (Ministerio de Economía y Competitividad), España, por la financiación de la investigación publicada en este artículo en virtud de las ayudas MAT2013-47898-C2-1-R y MAT2012- 36341. Patricia Enrique-Jimenez agradece al MINECO por la beca FPI (Formación del Personal Investigador)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Application of synchrotron infrared micro-reflectance for the study of diverse materials

  • González-Castillo, Eduin I.
  • Shuttleworth, Peter S.
  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Flores, Araceli
  • Ania, F.
  • Salavagione, Horacio J.
  • Gómez-Fatou, Marián A.
  • Yousef, Ibraheem
  • Kreuzer, Martin
  • Ellis, Gary James
Madrid from October 9-11, 2017. -- https://w3.ual.es/Congresos/AUSE/CONGRESO2017/index_congreso.html, EIGC acknowledges a PhD grant from the CONACYT (Mexico). SQD and PEJ acknowledge FPI Fellowships, and PSS a Ramón y Cajal PostDoc Fellowship, from the MINECO (Spain). MINECO also provided financial support through Grants MAT2014-54231-C4-4P, MAT2014-59674-JIN, MAT2013-47898-C2-1R and MAT2013-47898-C2-2R., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Correlation between nanostructure and electrical properties in SEBS nanocomposites incorporating graphene modified with polyethylene brushes

  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Salavagione, Horacio J.
  • Flores, Araceli
  • Ania, F.
  • Gómez-Fatou, Marián A.
Madrid from October 9-11, 2017. -- https://w3.ual.es/Congresos/AUSE/CONGRESO2017/index_congreso.html, Financial support from MINECO (MAT2013-47898-C2-1-R and MAT2013-47898-C2-2-R). S.Q.-D. and P.E.-J. acknowledge a FPI Fellowship., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Searching for effective compatibilizing agents for the preparation of poly(ether ether ketone)/graphene nanocomposites with enhanced properties

  • Martínez-Gómez, Aránzazu
  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Flores, Araceli
  • Ania, F.
  • Gómez-Fatou, Marián A.
  • Salavagione, Horacio J.
The homogeneous dispersion of graphene into poly(ether ether ketone) (PEEK) remains a challenging task mostly due to the resistance of PEEK to most common organic solvents. The present investigation describes a careful selection of compatibilizing agents that allows effectively dispersing graphene into PEEK. Polyetherimide (PEI), polysulfone, (PSU), poly(1,4-phenylene ether-ether-sulfone) (PEES) and sulfonated PEEK (SPEEK) are considered as potential compatibilizers and the mechanical, thermal and electrical properties of PEEK/graphene nanocomposites with different filler contents are evaluated. Significant electrical conductivity values are obtained for the nanocomposite with SPEEK (σ > 0.01 S·cm at 4 wt% filler content) and the one incorporating PEI exhibited a percolation threshold below 2 wt%. Finally, the nanocomposites including SPEEK, PEI and PEES show a clear enhancement of the mechanical properties with increasing graphene content. Hence, nanocomposites incorporating PEI and SPEEK as compatibilizers displayed optimized electrical and mechanical properties, in addition to a thermal stability up to 550 °C., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R, MAT2013-47898-C2-2-R, MAT2017-88382-P is gratefully acknowledged. SQD and PEJ also acknowledge the MINECO for a FPI Fellowship. The authors wish to thank Mr. David Gómez (Characterization Service of the CSIC-ICTP) for the SEM measurements, Mr. J. Gonzalez-Casablanca (CAP, University Rey Juan Carlos, Spain) for TEM measurements and Dr. J.P. Fernández-Blázquez (IMDEA Materials, Spain) for assistance with hot-press preparation of nanocomposites films., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanoindentation mapping of multiscale composites of graphene-reinforced polypropylene and carbon fibres

  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Salavagione, Horacio J.
  • Fernández-Blázquez, J. P.
  • Monclús, M.A.
  • Guzmán de Villoria, R.
  • Gómez-Fatou, Marián A.
  • Ania, F.
  • Flores, Araceli
The local mechanical properties of hierarchically reinforced laminates of graphene-isotactic polypropylene (iPP) and carbon fibres are investigated by nanoindentation. Carbon fibre fabrics are alternated with films of iPP reinforced with different graphene contents and types (pristine and modified with iPP brushes). The distribution of the mechanical data obtained around one isolated carbon fibre at the boundary with the polymer layer is compared with a similar analysis far away from any fibre. In the case of neat iPP, a high E′ tail can be identified with a micrometre-sized interphase showing distinct properties from those of the polymer matrix. With increasing amount of graphene, the E′ distribution including the high E′ tail progressively shifts to higher values. It is suggested that graphene platelets accumulate at the front of the ply due to the filtering effect of the carbon fibres giving rise to a transition region, superimposed on the interphase, with enhanced properties. Nanoindentation studies reveal that the chemical modification of graphene by short-chain iPP lowers the reinforcement of the nanofiller, both near and far away from the fibres front. On the other hand, indentation push-in tests suggest that modified graphene increases the resistance of the laminate under shear stress conditions. However, from the point of view of overall performance, it lowers the electrical conductivity across the laminate. The work offers a discussion of the role of graphene type and content on the properties of the multiscale composite., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, under grants MAT2013-47898-C2-1-R, MAT2013- 47898-C2-2-R and MAT2017-88382-P is gratefully acknowledged. PEJ and SQ also acknowledge MINECO for a FPI fellowship. We are also indebted to the Department of Crystallography (IQFR, CSIC) for providing Xray diffraction facilities. Authors wish to thank Dr. Nuria García (ICTPCSIC) for profilometry measurements and Mr. David Gómez of the Characterization Service of ICTP-CSIC, for SEM studies., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrospinning of poly(ß-hydroxybutyrate) scaffolds: morphology and aging

  • Romo-Uribe, Ángel
  • Flores, Araceli
  • Domínguez-Díaz, Maraolina
11 pags., 11 figs., 1 tab., Fibrous polymeric scaffolds that comprise capabilities of biomimicry to the native tissue architecture and achieve functional tissue-engineered products with minimal surgical implantation. This research focused on the production of fibrous scaffolds of biodegradable microbial poly(β-hydroxybutyrate) (PHB) by electrospinning. Processing conditions were found to influence the morphology of the scaffolds, which, in turn, controlled the wettability and aging behavior, quite important for medical applications. Commercial and biosynthesized PHB from a mutant Azotobacter vinelandii OP strain were investigated. The morphology and wettability of the fibrous scaffolds were characterized using optical, atomic and scanning electron microscopy. Tuning the voltage and the solution concentration (at constant flow rate) produced either a filamentous morphology or aggregates of filaments. The wettability correlated with the degree of porosity, and predominantly a hydrophobic behavior was attained in an otherwise hydrophilic material. Aging, monitored at room temperature up to 11 months by degree of crystallinity, α, showed that scaffolds with filamentous morphology exhibited an increase in crystallinity, leading to brittleness. However, scaffolds with aggregated filaments were quite stable as the degree of crystallinity remained constant over the 11-month period. Applications are envisioned for PHB biomimetic scaffolds in cell growth and bone tissue regeneration
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Creep behaviour of elastomeric nanocomposites by flat punch indentation: Influence of graphene modification and content

  • Ania, F.
  • Gómez-Fatou, Marián A.
  • Salavagione, Horacio J.
  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Flores, Araceli
Creep can be understood as the resistance of a material to a continuous stress and represents an important property for engineering design. The creep behaviour of a series of nanocomposites with electromechanical applications based on a thermoplastic elastomer, poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS), and small amounts of graphene has been explored using cylindrical flat punch depth-sensing indentation. Special attention is paid to the influence of the nature of the polymer brushes (polyethylene or polystyrene) attached to the graphene surface. Common methodologies for indentation creep analysis are critically examined and brought together to provide a comprehensive picture of creep deformation. It is found that graphene significantly reduces the creep rate and this is most significant under viscoplastic deformation than in the linear viscoelastic regime. Most interesting, polyethylene branches reduce visco-elastic-plastic flow in a more effective manner and this is attributed to the selective interaction of the filler with the matrix chains., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, under grants MAT2013-47898-C2-1-R, MAT2013- 47898-C2-2-R and MAT2017-88382-P is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Development of Multifunctional PEEK Nanocomposites based on Graphene

  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Flores, Araceli
  • Ania, F.
  • Gómez-Fatou, Marián A.
  • Salavagione, Horacio J.
  • Martínez-Gómez, Aránzazu
ECCM18 - 18th European Conference on Composite Materials, Athens, Greece, 24-28th June 2018 . -- 7 pags., 2 figs., 1 tab., In this communication we present the preparation of multifunctional Polyether ether ketone (PEEK) nanocomposites with graphene. PEEK is an important high-perfomance semicrystalline thermoplastic matrix that displays a unique combination of toughness, stiffness, chemical and solvent resistance, retention of physical properties at high temperatures and recyclability. A relevant step forward to expand its field of application is the incorporation of electrical conductivity, developing multifunctional materials. Therefore, graphene has been incorporated into the matrix aiming to achieve electrical conductivity without a significant detriment on PEEK properties. The accomplishment of an effective transfer of the properties from graphene to the matrix is controlled by the nanofiller dispersion within the matrix and the presence of a strong polymer/graphene interface. One of the most efficient strategies to improve both parameters consists on the covalent modification of graphene with short polymer chains and their subsequent use as filler in the cognate polymer matrix1-3. Nevertheless, this approach is unachievable in our case since PEEK is insoluble in organic solvents. An alternative strategy, proven to be effective to increase carbon nanotubes dispersion within PEEK matrix4-5, consists on nanofiller wrapping in compatibilizing polymers. In this study we prepared PEEK/graphene nanocomposites using compatibilizers like polyetherimide (PEI), poly(1-4-phenylene ether-ether sulfone) (PEES), polysulfone (PSU) and sulfonated PEEK (SPEEK), which are amorphous thermoplastic polymers miscible with and structurally similar to PEEK. Composites incorporating compatibilizer/graphene nanofillers display a slight decrease on the thermal stability with respect to PEEK, which is related to the intrinsic thermal stability of the compatibilizer employed. Regarding the electrical conductivity, significant conductivity values were measured depending on both nanofiller concentration and the nature of the compatibilizer. A slight enhancement was observed on the mechanical properties of the nanocomposites for some of the non-covalent functionalized graphene. The morphology, thermal behavior and mechanical performance of all nanocomposites will be compared and the best strategy leading to a balance among electrical, thermal and mechanical properties will be shown., Financial support from MINEICO (Ministerio de Economía, Industria y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R and MAT2013-47898-C2-2-R is gratefully acknowledged. SQD and PEJ also acknowledge the MINECO for a FPI Fellowship.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nanoindentation of Graphene-Reinforced Polypropylene Nanocomposites Laminated with Carbon Fibres

  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Salavagione, Horacio J.
  • Gómez-Fatou, Marián A.
  • Ania, F.
  • Flores, Araceli
ECCM18 - 18th European Conference on Composite Materials, Athens, Greece, 24-28th June 2018 . -- 7 pags., 6 figs., The mechanical properties of graphene-reinforced polypropylene nanocomposites laminated with alternating carbon fibre mats have been studied at a local scale by nanoindentation and results are correlated with morphological studies by means of scanning electron microscopy (SEM). Mechanical maps (storage modulus and hardness) have been obtained using indentation depths of a few tens of nanometres. Analysis of the distribution of E´ values close to and far away from isolated carbon fibres offers a comprehensive understanding of the role of graphene on the mechanical properties of the transition region between the reinforced matrix and the microsized fibres., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R, MAT2013-47898-C2-2-R is gratefully acknowledged. PEJ and SQ also acknowledge the MINECO for a FPI Fellowship. The authors wish to thank Mr. David Gómez of the Characterization Service of the Institute of Polymer Science & Technology, CSIC, for the SEM measurements.