Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Cellulose nanofibers as substrate for flexible and biodegradable moisture sensors

  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
  • Marín-Sánchez, Antonio
  • Wicklein, Bernd
  • Salmerón, José F
  • Castillo Morales, María Encarnación|||0000-0001-6476-8105
  • Bobinger, Marco
  • Salinas Castillo, Alfonso|||0000-0002-1360-6699
Flexible and biodegradable electronics is attracting the interest of the Internet of Things industry. The necessity of sustainable development and environmental friendly electronic devices forces manufactures to reduce electronic wastes and toxic residues. Cellulose nanofibers are biodegradable and flexible materials suitable to build self supported film electronics and are seeing first employment in sensor fabrication. In this work, cellulose nanofibers based moisture sensors are reported, which are characterized at different working frequencies showing a good dependence with relative humidity (RH). A transparent and fully biodegradable moisture sensor was fabricated based on a PEDOT:PSS electrode showing a wide operation range from 20% to 85%RH, where CNF film acts as the sensing layer without any additional processing. In order to manufacture the sensor, a one-step fabrication method based on screen-printing was applied, which offers a more reproducible and cost-effective solution than others techniques. In addition, this method offers the possibility to easily redesign the sensor saving time and money. Thus, our work presents a versatile, transparent, self-supported film moisture sensor with a promising adaptability to the green-electronics industry., H2020-MSCA-IF-2017-794885-SELFSENS, MAT2015-71117-R, ID2019-107022RJ-I00, IJCI-2015-23886
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Fabrication of low cost and low impact RH and temperature sensors for the Internet of Environmental-Friendly Things

  • Falco, Aniello
  • Sackenheim, Philipp S
  • Romero Maldonado, Francisco Javier
  • Becherer, Markus
  • Lugli, Paolo
  • Salmerón, José F
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
Given the increasing number of connected devices as a consequence of the Internet of Things (IoT) revolution, the issue of the removal and recycling of electronics is becoming more and more urgent. In this context, biodegradable electronics is expected to be one of the biggest technological revolutions to tackle this problem. Following this direction, in this work we present the fabrication and characterization of temperature and humidity sensors based on biodegradable materials with the goal of making their removal easier as well as reducing their environmental impact. In particular, these multi-sensing devices were fabricated following a screen-printing process using a carbon-based paste and a conjugated polymer, both on paper and on a water soluble substrate. The results are more than promising and show how with our biodegradable sensors it is possible to obtain a sensitivity of 1 dec/20%RH to moisture content and around 0.04%/°C sensitivity to temperature. It is demonstrated that the simplicity and flexibility of the fabrication approach followed in this work paves the way to a set of new “green” IoT nodes that could be extended to wide range of sensing applications.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Fabrication and characterization of capacitive humidity sensors based on emerging flexible technologies

  • Romero Maldonado, Francisco Javier
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
  • Salinas Castillo, Alfonso|||0000-0002-1360-6699
  • Ohata, Akiko
  • Morales Santos, Diego Pedro|||0000-0002-3294-8934
  • Becherer, Markus
  • Rodríguez Santiago, Noel|||0000-0002-6032-6921
This work presents a case-based comparison between two emerging fabrication techniques for the development of conductive patterns for flexible electronics: inkjet-printing and nanographene production by laser-scribing. In particular, these two methods are used to fabricate planar interdigitated electrode (IDE) capacitors with Kapton® HN polyimide as supporting flexible substrate. Silver-based electrodes are manufactured by inkjet-printing, while a laser-scribing technique is used to obtain laser-reduced graphene oxide (laser-rGO) patterns from deposited graphene oxide (GO) and laser-induced graphene (LIG) layouts from the bare polyimide substrate. The comparison is focused on the application of these IDE capacitors as relative humidity (RH) sensors. The different sensors are benchmarked in terms of sensitivities to RH as well as thermal drift and linearity considering frequency dependencies. The results show that the manufactured capacitors exhibit a very competitive performance as capacitive structures when compared with other similar capacitive sensors from the literature. Furthermore, inkjet-printed and LIG-based capacitors stand out for its thermal stability and linearity.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

An Optimized Measurement Algorithm for Gas Sensors Based on Carbon Nanotubes: Optimizing Sensor Performance and Hardware Resources

  • Castillo Morales, María Encarnación|||0000-0001-6476-8105
  • Salmerón, José F
  • Falco, Aniello
  • Loghin, Florin C
  • Romero, Francisco J
  • Lugli, Paolo
  • Morales Santos, Diego Pedro|||0000-0002-3294-8934
This paper presents a novel algorithm for the measurement of resistive-type gas sensors with carbon nanotubes (CNTs) as sensitive layer. Contrary to conventional strategies, which extract the sensor information from the normalized resistance, the proposed algorithm is based on the variation in resistance over time. The results have demonstrated that the time necessary to get the maximum performance of these sensors is reduced around a 25% when compared with the conventional approach for any of the recovery strategies analyzed (passive desorption, external heating, or dc voltage). The hardware implementation of the proposed algorithm in a field-programmable gate array (FPGA) has also demonstrated that, in addition to optimizing the sensor performance in terms of time response and sensitivity, this measurement algorithm yields a significant minimization of the sensor readout circuit resources at both software and hardware levels paving the way for future development of smart sensors for the Internet of Things (IoT) applications.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Facile manufacturing of sub-mm thick CNT-based RC filters

  • Loghin, Florin
  • Falco, Aniello
  • Moreno-Cruz, Fernando
  • Morales Santos, Diego Pedro|||0000-0002-3294-8934
  • Salmerón, José F
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
CNT-Based RC networks are described with the purpose of showing empirical findings on the influence of the interdigitated electrodes (IDE) spacing, the dispersant compound and the number of deposited layers, on the impedance magnitude and phase of the CNTs. Additionally, we propose use-cases for these networks, applying them to the realization of filters of second order with easily tunable cut-off frequency, and with the inherent advantages of CNTs and printed technologies, rendering them a prime choice for applications where thin and flexible second order filters are necessary.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Flexible and robust laser-induced graphene heaters photothermally scribed on bare polyimide substrates

  • Bobinger, Marco
  • Romero Maldonado, Francisco Javier
  • Salinas Castillo, Alfonso|||0000-0002-1360-6699
  • Becherer, Markus
  • Lugli, Paolo
  • Morales Santos, Diego Pedro|||0000-0002-3294-8934
  • Rodríguez Santiago, Noel|||0000-0002-6032-6921
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
We demonstrate the feasibility of fabricating cost-effective and robust laser-induced graphene (LIG) flexible heaters with an innovative technique based on the photothermal production of graphene with a foam-like morphology. The produced devices are precisely defined on a bare polyimide substrate without the need of photomasks by employing a computer numerical control (CNC) driven laser diode. The electrical properties of the LIG-based heaters can be tailored by adjusting the laser power. The resulting conductive material exhibits electrical and chemical properties which are similar to the ones for graphene such as a negative temperature coefficient of −0.46 m°C−1 and a maximum operating temperature of around 400 °C. The developed heaters can outperform the existing emerging technologies showing a very rapid and stable response up to 225 °C with the extra features of flexibility, biocompatibility, and environmental friendliness.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Screen-Printed Chipless Wireless Temperature Sensor

  • Albrecht, Andreas
  • Salmerón, José F
  • Becherer, Markus
  • Lugli, Paolo
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
A chipless wireless sensor for temperature monitoring is described in this work. The sensor is fabricated by screen printing of an RLC circuit on a flexible substrate. The sensing element is a resistive carbon paste with positive temperature coefficient placed in a small area in the interconnection between the inductor and the capacitor. This sensing layer modifies the resonance frequency of the circuit when the temperature varies. We also show the influence of the sensor sensitivity with respect to the reading distance.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Design guidelines of Laser Reduced Graphene Oxide Conformal Thermistor for IoT applications

  • Romero Maldonado, Francisco Javier
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
  • Toral López, Víctor
  • Castillo, Encarnación
  • García Ruiz, Francisco Javier
  • Morales Santos, Diego Pedro|||0000-0002-3294-8934
  • Rodríguez Santiago, Noel|||0000-0002-6032-6921
This work presents a complete temperature sensing solution based on a conformal laser-reduced graphene-oxide temperature transducer acting as thermistor. The process to implement the temperature-sensitive element is described in detail; from the raw material to the optimum laser scribing conditions used to define the resistive component. The final transducer is fabricated on a flexible plastic substrate and can be attached to any surface as a conformal patch. To provide a full demonstrator of the potential of this technology, the thermistor is integrated in an IoT sensing platform with wireless data transmission capability using a reconfigurable ultra-low power System-on-Chip.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

A handwriting method for low-cost gas sensors

  • Loghin, Florin
  • Falco, Aniello
  • Albrecht, Andreas
  • Salmerón, José F
  • Becherer, Markus
  • Lugli, Paolo
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
In this study, we report on an automated method based on a handwritten technique for the fabrication of low-cost gas sensors based on carbon nanotube (CNT) networks. Taking advantage of the inherent low-cost, flexible, and uncomplicated characteristics of pen-based techniques and combining them with an automated robotic system allows for high-resolution patterns, high reproducibility, and relatively high throughput considering the limitations of parallel processing. To showcase this, gas sensors capable of sensing NH3, CO2, CO, and ethanol, as well as temperature and relative humidity, are fabricated and characterized displaying competitive performance in relation to previously reported devices. The presented process is compatible with a variety of solutions and inks and, as such, allows for an easy integration into existing printing and coating frameworks with the greatest advantage being the ease of creating prototypes because of the nonstringent material requirements.
Digibug. Repositorio Institucional de la Universidad de Granada
Publicación Artículo científico (JournalArticle)

Optimization of Cost-Effective and Reproducible Flexible Humidity Sensors Based on Metal-Organic Frameworks

  • Toral López, Víctor
  • Loghin, Florin
  • Rodríguez Diéguez, Antonio|||0000-0003-3198-5378
  • Lapresta Fernández, Alejandro
  • Morales Santos, Diego Pedro|||0000-0002-3294-8934
  • Rivadeneyra Torres, Almudena|||0000-0001-8133-1992
  • Salinas Castillo, Alfonso|||0000-0002-1360-6699
This research was partially supported by the fellowship H2020-MSCA-IF-2017-794885-SELFSENS and by the Spanish Ministry of Education, Culture and Sport under Grant FPU18/01376 and funded by Spanish ministry of Science and Innovation grant number PGC2018-102052-B-C21., In this letter, we present the extension of a previous work on a cost-effective method for fabricating highly sensitive humidity sensors on flexible substrates with a reversible response, allowing precise monitoring of the humidity threshold. In that work we demonstrated the use of three-dimensional metal-organic framework (MOF) film deposition based on the perylene-3,4,9,10-tetracarboxylate linker, potassium as metallic center and the interspacing of silver interdigitated electrodes (IDEs) as humidity sensors. In this work, we study one of the most important issues in efficient and reproducible mass production, which is to optimize the most important processes’ parameters in their fabrication, such as controlling the thickness of the sensor’s layers. We demonstrate this method not only allows for the creation of humidity sensors, but it also is possible to change the humidity value that changes the actuator state., Spanish Ministry of Education, Culture and Sport H2020-MSCA-IF-2017-794885-SELFSENS, Spanish Government FPU18/01376, PGC2018-102052-B-C21