Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 32
Encontrada(s) 1 página(s)

Docta Complutense
Datos de investigación Set de datos (Dataset)

Data: In vitro corrosion-assisted cracking of AZ31B Mg alloy with a hybrid PEO+MWCNTs/PCL coating

  • Daavari, Morteza
  • Conde, Ana
  • Atapour, Masoud
  • HosseinpourRokni, Mohsen
  • Mora Sánchez, Hugo
  • Mohedano Sánchez, Marta
  • Matykina, Endzhe
  • Arrabal Durán, Raúl
The effects of multi-walled carbon nanotubes (MWCNTs) incorporation and polycaprolactone (PCL) post-treatment on the environmental-assisted cracking behaviour of a plasma electrolytic oxidation (PEO) coated AZ31B Mg alloy were elucidated in this study. Slow strain rate tensile (SSRT) experiments were carried out in simulated body fluid (SBF) for the bare material and different coating systems with and without MWCNTs and PCL overlay. Electrochemical impedance spectroscopy (EIS) and microscopic examinations (SEM and optical) were also conducted to reveal the role of corrosion on the mechanical response. In spite of the significant positive influence of the PEO coatings (with and without MWCNTs) on the bio-electrochemical behaviour of the AZ31B alloy, the environmental-assisted cracking performance was only marginally improved. Furthermore, PEO+MWCNTs/PCL coating system increased the fracture strain of the specimens by 7% compared to the uncoated specimens. Based on the SEM and optical micrographs, hydrogen embrittlement was suggested as the main cause of failure of the coated specimens under the in vitro slow strain rate test conditions.
Docta Complutense
Datos de investigación Set de datos (Dataset)

Data: Flash plasma electrolytic oxidation and electrochemical behaviour in physiological media of additive manufacturing Ti6Al4V alloy

  • Mora Sánchez, Hugo
  • Ramos, Carolina
  • Mohedano Sánchez, Marta
  • Torres, Belén
  • Arrabal Durán, Raúl
  • Matykina, Endzhe
The objective of this work is to understand the plasma electrolytic oxidation (PEO) treatment and electrochemical behaviour of a Ti6Al4V alloy manufactured by a laser powder bed fusion additive manufacturing (AM) technique known as direct metal laser sintering (DMLS). Ca and P-containing coatings were produced with short time (<120 s) PEO treatments (also termed as Flash-PEO) obtaining 3–10 μm-thick coatings on both the AM alloy and a conventional counterpart. Subsequently, the electrochemical behaviour of the bare and treated alloys was assessed in a modified α-MEM solution via potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The fine α-lamellar microstructure of the AM alloy with small β-phase particles at the interlamellar spaces was seen to advance the onset of sparking promoting faster growth of PEO coating in comparison to the conventional alloy. Flash-PEO coatings enhanced the corrosion protection of both conventional and AM alloys, the thinnest (<3 μm) coatings providing up to three times greater protection. AM Ti6Al4V was found to be susceptible to localized crevice corrosion which could be assigned to the high grain boundary density. Flash-PEO treatments, even as short as 35 s, were sufficient to successfully prevent it.
Docta Complutense
Datos de investigación Set de datos (Dataset)

Data: Corrosion of additively manufactured Ti6Al4V alloy in saline and acidic media

  • Mora Sánchez, Hugo
  • Collado Vian, Miguel
  • Mohedano Sánchez, Marta
  • Arrabal Durán, Raúl
  • Matykina, Endzhe
The present work aims to provide corrosion performance data for an additively manufactured Ti6Al4V alloy in saline and polluted environments. The as-received additively manufactured material underwent heat treatment at 850 °C for 3 h to transform the acicular α’ microstructure into a lamellar α microstructure. Comparative corrosion assessments were conducted between the heat-treated substrates, the as-received condition, and a conventionally mill-annealed alloy. Potentiodynamic polarization experiments were carried out in saline (3.5 wt.% NaCl) and acid aqueous media ((NH4)2SO4 containing Harrison’s solution). The corrosion performance of additively manufactured substrates matched or surpassed that of the conventional alloy in Harrison’s solutions while remaining inferior in saline medium, despite forming a thicker passive film. Overall, the XY plane showed better corrosion performance, particularly after the elimination of the acicular α’ martensite by the applied heat treatment. The results also suggested that the presence of the coarse β phase was beneficial in 3.5 wt.% NaCl solution and detrimental in Harrison’s solutions, more so in acidified and fluorinated conditions.
Docta Complutense
Datos de investigación Set de datos (Dataset)

Data: Degradation rate control issues of PEO-coated wrought Mg0.5Zn0.2Ca alloy

  • Moreno Turiegano, Lara
  • Mohedano Sánchez, Marta
  • Arrabal Durán, Raúl
  • Matykina, Endzhe
Bioactive plasma electrolytic oxidation (PEO) coatings were developed on a wrought Mg0.5Zn0.2Ca alloy using a transparent electrolyte for easy maintenance and waste disposal, compared to a conventional suspension-based solution. Treatment times of 300, 600, and 900 s were evaluated for their effects on coating morphology, composition, and corrosion resistance. A short-time electrochemical impedance spectroscopy (EIS) screening was utilized to identify coatings with optimal corrosion protection. To assess the degradation rate and corrosion mechanisms, hydrogen evolution was monitored under pH-controlled quasi-in vivo conditions over extended immersion periods. Coating thickness increased by only 3% from 300 to 900 s of treatment (13 and 18 µm, respectively), with pore bands formed near the barrier layer at 900 s. The short-term EIS screening revealed that the coatings produced at 600 and 900 s were less protective and consistent than those at 300 s due to the presence of pore bands, which increased permeability. Hydrogen evolution measurements during 5 days of immersion at pH 7.4 indicated a tenfold higher degradation rate of the PEO-coated alloy compared to the bare substrate. Therefore, none of the PEO coatings provided effective corrosion protection after 24 h of immersion, which is attributed to crack formation at the PEO/corrosion products interface. This highlights the importance of crevices in the corrosion of Mg-Zn-Ca alloys. The presence of ZnO exacerbates the corrosion of magnesium in crevice areas.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Magnesium Addition and High Energy Processing on the Degradation Behavior of Iron Powder in Modified Hanks’ Solution for Bioabsorbable Implant Applications

  • Estrada, Rafael Guillermo
  • Multigner, M.
  • Lieblich, Marcela
  • Fajardo, Santiago
  • Rams Ramos, Joaquín
This paper shows the results of applying a combination of high energy processing and magnesium (Mg) as an alloying element in a strategy for enhancing the degradation rate of iron (Fe) for applications in the field of non-permanent medical implants. For this purpose, Fe powder was milled with 5 wt% of Mg (Fe5Mg) and its microstructure and characterized degradation behavior. As-received Fe powder was also milled in order to distinguish between the effects due to high energy processing from those due to the presence of Mg. The powders were prepared by high energy planetary ball milling for 16 h. The results show that the initial crystallite size diminishes from >150 nm to 16 nm for Fe and 46 nm for Fe5Mg. Static degradation tests of loose powder particles were performed in Hanks’ solution. Visual inspection of the immersed powders and the X-ray diffraction (XRD) phase quantification indicate that Fe5Mg exhibited the highest degradation rate followed by milled Fe and as received Fe, in this order. The analysis of degradation products of Fe5Mg showed that they consist on magnesium ferrite and pyroaurite, which are known to present good biocompatibility and low toxicity. Differences in structural features and degradation behaviors of milled Fe and milled Fe5Mg suggest the effective dissolution of Mg in the Fe lattice. Based on the obtained results, it can be said that Fe5Mg powder would be a suitable candidate for non-permanent medical implants with a higher degradation rate than Fe., Financial support of the Ministry of Science and Innovation of Spain (MICINN) PID2019-104351GB-C21, PCIN-2017-036 (M-era.Net2016:4128, EU-FEDER), and RTI2018-096391-B-C31, and Comunidad de Madrid ADITIMAT-CM (S2018/NMT-4411) are greatly acknowledged. R. Estrada thanks MICINN for FPI grant PRE2020-092118, and S. Fajardo expresses his gratitude to the State Research Agency (MICINN), the Spanish National Research Council (CSIC), and the European Regional Development Fund (ERDF) for their support under project RYC2019-027006-I (AEI/FEDER/UE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Aqueous colloidal processing of W and WC-based composites, sintering and mechanical properties at high temperature

  • García Ayala, Esperanza Macarena
E. M. Garcia-Ayala, Z. Gonzalez, B. Ferrari, J. Y. Pastor, A. J. Sanchez-Herencia, Colloidal Approach to the Additive Manufacturing of W-based Materials, in: EuroPM 2018 Proceedings (2020) ISBN: 978-1-899072-50-7. E.M. Garcia-Ayala, S. Tarancon, B. Ferrari, J.Y. Pastor, A.J. Sanchez-Herencia, "Thermomechanical behaviour of WC-W2C composites at first wall in fusion conditions", Int. J. Refract Metal. Hard Mater., 98 105565 (2021). DOI: 10.1016/j.ijrmhm.2021.105565 E.M.Garcia-Ayala, L.Silvestroni, J.Yus, B.Ferrari, J.Y.Pastor and A.J.Sanchez-Herencia"Colloidal processing and sintering of WC-based ceramics with low Ni content as sintering aid", J. Eur. Ceram. Soc, 41 (3) 1848, -1858 (2021).DOI: 10.1016/j.jeurceramsoc.2020.10.038 M.E. Garcia-Ayala, S. Tarancon, Z. Gonzalez, B. Ferrari, J.Y. Pastor, A.J. Sanchez-Herencia, "Processing of WC/W composites for extreme environments by colloidal dispersion of powders and SPS sintering",Int. J. Refract. Met. Hard Mater., 84,105026 ( 2019,)DOI:10.1016/j.ijrmhm.2019.105026, [EN] There have been many advanced technologies that operates at high temperature under severe conditions, such as those over the inner walls of the future fusion nuclear reactor (ITER, DEMO, etc.). Refractory metals such as tungsten are proposed as optimum materials to face these conditions. Pure ceramics, such as WC and metal ceramics are proposed also as alternative materials for the components that require operate at high temperature under high wear conditions or neutronic damage. For that reason, the design of complex compositions and microstructures is necessary to achieve reliable materials under these conditions. That makes this work investigate on colloidal processing W and WC materials, as well as their composites with nickel for softening of the sintering conditions. Aqueous colloidal processing is proposed as an alternative to the solvent-less techniques. By the study of zeta potential and chemical analysis of powders suspended in water the optimal conditions for high solid content suspension preparation were determined at different pH conditions and considering the use a cationic dispersant (polyethyleneimine, PEI). The rheological studies have determined the maximum solid content through the Krieger-Dougherty model adjustment, so the time spent removing water after powder preparation can be diminished. Three different types of composite powders were prepared: WC-W, WC-Ni and W-Ni. For WC-W composites, the amount of metallic phase was fixed in 10, 20 and 50 vol.%, while for WC-Ni and W-Ni mixtures, the amount of metallic nickel phase was 5 vol.% (3 wt.%). Three different sintering methods are used: Spark Plasma Sintering (SPS), Hot-Press Sintering (HPS) and Vacuum Sintering (VS). WC-W materials were sintered by SPS at 1700 and 1800 oC for 10 min and 60 MPa. The crystalline and chemical studies determined the high reactivity between W and WC during the thermal cycle, which gives place to the presence of a third species: tungsten semicarbide (W2C), which provoked all the W consumption. Mechanical tests at high temperatures for the W2C/WC composites demonstrated their excellent properties and performance at conditions similar to the ITER divertor walls. A self-reinforcement behaviour due to the appearing of metallic tungsten in the microstructure as the temperature approach to 1200 ºC is described. On the other hand, mixture of WC with Ni and W with Ni, obtained by aqueous colloidal processing were sintered by the three mentioned sintering techniques and the differences between them studied. Two types of Ni powders were used: a commercial nickel (cNi) and a nanometric nickel synthesized in the lab (nNi). WC-Ni sintered by HPS achieved a density higher than 98%, which was not the case of SPS and VS sintered samples. SEM/EDX observations demonstrated that sintering was by a solution-precipitation mechanism that leaved the nickel located in the grain junctions, while there were slight carbon precipitations favoured by the thermodynamical conditions during the thermal cycle. For W-Ni alloys, successful results were obtained from VS process, achieving 96% density and a fully dense microstructure. In this case, W and Ni reacts while thermal treatment, giving an intermetallic species: NiW. For both WC-Ni and W-Ni materials, the presence of small amounts of Ni showed a clear softening of sintering conditions, which make the sintering of W and WC an affordable method for wide productions in terms of both technology and economic cost. Mechanical tests of these composites exhibited a ductilisation of the materials due to the presence of the nickel phase, which matches to the data found in the literature for this type of composites and alloys., [ES] Existen multitudes de tecnologías avanzadas capaces de operar a alta temperatura bajo condiciones severas, como aquellos que conforman las paredes interiores de futuros reactores de fusión nuclear (ITER, DEMO, etc.). Los metales refractarios como el wolframio se proponen como los materiales óptimos para trabajar bajo estas condiciones. Los cerámicos puros, como el WC, y los composites cerámica-metal (cermets) también se presentan como claras alternativas para aquellos materiales requeridos para operaciones a alta temperatura, bajo alto desgaste o radiación neutrónica. Por este motivo, el diseño de composiciones complejas y microestructuras es necesario para lograr la preparación de materiales que trabajen en dichas condiciones. Todo ello hace que se profundice en la Investigación de materiales de W y WC formulados por procesamiento coloidal, así como sus materiales compuestos con níquel metálico para suavizar sus condiciones de sinterización. El procesamiento coloidal en base acuosa se propone como una fuerte alternativa a las tradicionales técnicas sin disolvente (en seco). Mediante el estudio del potencial zeta y el análisis químico de los polvos suspendidos en agua, las condiciones óptimas para la preparación de suspensiones con alto contenido en sólidos se determinaron a diferentes valores de pH, y considerando el uso de un dispersante catiónico (polietilenimina o PEI). Los estudios reológicos determinaron el máximo contenido en sólidos mediante el ajuste de Krieger-Dougherty, de tal forma que se lograba disminuir el tiempo de eliminación de disolvente. Se prepararon tres tipos diferentes de polvos compuestos: WC-W, WC-Ni y W-Ni. Para los composites WC-W, la cantidad de fase metálica se fijó en 10, 20 y 50 vol.%, mientras que para las mezclas WC-Ni y W-Ni, la cantidad de níquel metálico fue de un 5 vol.% (3% en peso). Se emplearon tres métodos distintos de sinterización: Sinterización asistida por Corriente Pulsada (SPS), Sinterización por presión asistida en caliente (HPS) y Sinterización a vacío (VS). Los materiales de WC-W se sinterizaron por SPS a 1700 y 1800 oC durante 10 minutos, a 60 MPa de presión. Los estudios químicos y de cristalinidad determinaron la alta reactividad entre W y WC durante el ciclo térmico, el cual dio lugar a la aparición de una tercera especie: el semicarburo de wolframio (W2C), lo que provocó el agotamiento total del wolframio metálico. Los ensayos mecánicos a alta temperatura para los compuestos W2C/WC demostraron sus excelentes propiedades a condiciones similares a las del divertor del ITER. Se describe un comportamiento de refuerzo mecánico debido a la aparición de wolframio metálico en la microestructura, a medida que se describe un ascenso de la temperatura hasta los 1200 oC. Por otra parte, las mezclas de WC con Ni, y W con Ni, obtenidas mediante procesamiento coloidal en agua, se sinterizaron a través de las tres técnicas ya mencionadas, por lo que se estudiaron los diferentes resultados. Se usaron dos tipos de polvo de Ni: un níquel comercial (cNi), y un níquel nanométrico sintetizado en el laboratorio (nNi). WC-Ni se sinterizó por HPS, logrando una densidad mayor al 98%, lo que no ocurrió en el caso de las muestras sinterizadas por SPS y VS. Los análisis por SEM/EDX demostraron que la sinterización seguía un mecanismo de disolución-precipitación, lo que provocó la localización del níquel metálico en los límites de grano, mientras que aparecieron algunas precipitaciones de grafito favorecidas por las condiciones termodinámicas durante el ciclo térmico. Para las aleaciones W-Ni, se obtuvieron resultados bastante exitosos para el proceso de sinterización a vacío (VS), alcanzando densidades superiores al 96%, así como una microestructura consolidada y totalmente densificada. En este caso, W y Ni reaccionan durante el tratamiento térmico, dando lugar a una nueva especie: el intermetálico NiW. Para ambos composites WC-Ni y W-Ni, la presencia de pequeñas cantidades de Ni mostró un claro suavizamiento de las condiciones de sinterización, lo que hace que la sinterización de W y WC se conciba como un método asequible para grandes producciones a escala industrial en términos tanto tecnológicos como económicos. Los ensayos mecánicos de estos materiales exhibieron una clara ductilización debido a la presencia de fase níquel, lo que coincide con los datos encontrados en la literatura para este tipo de composites y aleaciones., Esta tesis se enmarca en el proyecto MAT2015-70780-C4-1-P del plan nacional, titulada “Procesamiento coloidal en medio acuoso de composites en base W y WC, sinterización y propiedades mecánicas a alta temperatura”. Este trabajo se ha desarrollado combinando las principales líneas de investigación de los dos grupos en los cuales se ha llevado a cabo el trabajo experimental: la Química Coloidal desarrollada por el grupo Tailoring through Colloidal Processing (ICV-CSIC), y el conocimiento sobre propiedades mecánicas del grupo CIME (UPM).
Docta Complutense
Datos de investigación Set de datos (Dataset)

Data: Combination of electron beam surface structuring and plasma electrolytic oxidation for advanced surface modification of Ti6Al4V alloy

  • Mora Sánchez, Hugo
  • Pixner, Florian
  • Buzolin, Ricardo
  • Mohedano Sánchez, Marta
  • Arrabal Durán, Raúl
  • Warchomicka, Fernando
  • Matykina, Endzhe
The objective of this work is to study for the first time the combination of electron beam (EB) surface structuring and plasma electrolytic oxidation (PEO) with the aim of providing a multiscale topography and bioactive surface to the Ti6Al4V alloy for biomedical applications. Ca and P-containing coatings were produced via 45 s PEO treatments over multi-scale EB surface topographies. The coatings morphology and composition were characterized by a means of scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The effect on the previous EB topography was evaluated by means of a 3D optical profilometry and electrochemical response via potentiodynamic polarization tests. In general, the PEO process, morphology, composition and growth rate of the coatings were almost identical, irrespective of the topography treated. Minimal local differences were found in terms of morphology, and the growth rate were related to specific topographical features. Nevertheless, all the PEO-coated substrates presented essentially the same corrosion resistance. Electrochemical tests revealed a localized crevice corrosion susceptibility of all the bare EB topographies, which was successfully prevented after the PEO treatment.
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Monitoring Crack Propagation in Skin-Stringer Elements Using Carbon Nanotube Doped Adhesive Films: Influence of Defects and Manufacturing Process

  • Fernández Sánchez-Romate, Xoan Xosé|||0000-0001-9283-4712
  • Moriche Tirado, Rocío
  • Renato Pozo, Angel
  • Jiménez Suárez, Alberto
  • Sánchez, María
  • Güemes Gordo, Jesús Alfredo|||0000-0002-6700-3455
  • Ureña, Alejandro
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Thermomechanical Characterisation of W-Eurofer 97 Brazed Joints

  • Tejado Garrido, Elena María|||0000-0002-5240-6702
  • Prado Escudero, Javier de
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Sánchez Martínez, María
  • Martín Sanz, Antonia|||0000-0003-1291-948X
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
  • Ureña Fernández, Alejandro
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

W-Cu Metal Matrix Composites for Next Generation Fusion Devices

Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Beneficial Effects of a WC Addition in FAST-Densified Tungsten

  • Novak, Sasa
  • Kocen, Matej
  • Sestan Zavasnik, Andreja
  • Galatanu, Andrei
  • Galatanu, Magdalena
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Tejado Garrido, Elena María|||0000-0002-5240-6702
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
  • Jenus, Petra
Archivo Digital UPM
Publicación Contribución de congreso (ConferenceOutput)

Influence of pressure history on jet dynamics in LIFT processes: simulation and experimental analysis

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Márquez Fernández, Andrés
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publicación Contribución de congreso (ConferenceOutput)

Evaluation of the Tensile and Elastic Properties of W/Cu Coatings for its Application to the FGM DEMO Divertor Concept

  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Tejado Garrido, Elena María|||0000-0002-5240-6702
  • Richou, Marianne
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Processing of WC/W Composites for Extreme Environments by Colloidal Dispersion of Powders and SPS Sintering

  • García Ayala, Esperanza Macarena
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • González Granados, Zoilo
  • Ferrari Fernández, Begoña
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
  • Sánchez Herencia, Antonio Javier
Archivo Digital UPM
Publicación Tesis doctoral (DoctoralThesis)

Aqueous colloidal processing of W and WC-based composites, sintering and mechanical properties at high temperature

Archivo Digital UPM
Publicación Tesis doctoral (DoctoralThesis)

Parametrization and simulation of blister-actuated laser-induced forward transfer (BA-LIFT) and LIFT for high-viscosity pastes

  • Moreno Labella, Juan José|||0000-0003-2612-707X
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Overlapping Limitations for ps-Pulsed LIFT Printing of High Viscosity Metallic Pastes

  • Muñoz Martín, David|||0000-0001-5837-6367
  • Chen, Yu
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Influence of the Gap between Substrates in the Laser-Induced Transference of High-Viscosity Pastes

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Vallejo, Guillermo
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
  • Morales Furió, Miguel|||0000-0001-7425-9742
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Numerical study of water-glycerol BA-LIFT: Analysis and simulation of secondary effects

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Márquez Fernández, Andrés
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Cavitation bubble evidence in BA-LIFT processes

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Picosecond Laser Shock Micro-Forming of Stainless Steel: Influence of High-Repetition Pulses on Thermal Effects

  • López López, José Manuel|||0000-0002-0298-3683
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Panizo Laíz, Miguel|||0000-0001-9061-7888
  • Gómez Rosas, Gilberto
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
  • Morales Furió, Miguel|||0000-0001-7425-9742
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Subwavelength LIPSS formation on SS304 by picosecond laser irradiation under water confinement

  • Patricia Rivera, Laura|||0000-0001-6373-654X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Chávez Chávez, Árturo|||0000-0003-3772-905X
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Gómez Rosas, Gilberto|||0000-0003-2040-3520
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publicación Tesis doctoral (DoctoralThesis)

Influence of time on the microstructure, thermal and mechanical properties of 1D PLA and PLA-Mg filaments after Fused Filament Fabrication

Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Bio-inspired redesign of a hip prosthesis stem for improving geometrical optimization time

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Palacios García, Teresa|||0000-0001-7777-6518
  • Calle Gómez, Fernando|||0000-0001-7869-6704
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Influence of HRGO Nanoplatelets on Behaviour and Processing of PMMA Bone Cement for Surgery

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Pastor, Ynés Yohana
  • Calle Gómez, Fernando|||0000-0001-7869-6704
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Characterisation and Modelling of PLA Filaments and Evolution with Time

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Ferrández Montero, Ana|||0000-0003-3399-1069
  • Ferrari Fernández, Begoña|||0000-0003-3377-6844
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Natural ageing of PLA filaments, Can it be frozen?

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Ferrández Montero, Ana|||0000-0003-3399-1069
  • Ferrari Fernández, Begoña|||0000-0003-3377-6844
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

The mechanical, thermal, and chemical properties of PLA-Mg filaments produced via a colloidal route for fused-filament fabrication

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Ferrández Montero, Ana|||0000-0003-3399-1069
  • Boccaccini, Aldo|||0000-0002-7377-2955
  • Ferrari Fernández, Begoña|||0000-0003-3377-6844
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Effects of accelerating the ageing of 1D PLA filaments after fused filament fabrication

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Effects of Laser Shock Processing on the Mechanical Properties of 6061-T6 Aluminium Alloy Using Nanosecond and Picosecond Laser Pulses

  • Arredondo Bravo, Martha Guadalupe|||0009-0005-6993-0171
  • Gómez Rosas, Gilberto|||0000-0003-2040-3520
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • López López, José Manuel|||0000-0002-0298-3683
  • Quiñones Galvan, Jose Guadalupe|||0000-0001-7931-3955
  • Rubio González, Carlos|||0000-0002-4447-3788
  • Casillas Rodríguez, Francisco Javier|||0000-0001-5928-8182
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Blister-actuated laser-induced forward transfer (BA-LIFT): Understanding blister dynamics for enhanced process control

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Candorcio Simón, Rocio|||0000-0001-6302-1595
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Lauzurica Santiago, Sara|||0000-0003-4398-6474
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359