Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Power Consumption Analysis of Operating Systems for Wireless Sensor Networks

  • Lajara Vizcaíno, José Rafael
  • Pérez Solano, Juan José
  • Pelegri-Sebastia, Jose|||0000-0002-7392-3178
In this paper four wireless sensor network operating systems are compared in terms of power consumption. The analysis takes into account the most common operating systems-TinyOS v1.0, TinyOS v2.0, Mantis and Contiki-running on Tmote Sky and MICAz devices. With the objective of ensuring a fair evaluation, a benchmark composed of four applications has been developed, covering the most typical tasks that a Wireless Sensor Network performs. The results show the instant and average current consumption of the devices during the execution of these applications. The experimental measurements provide a good insight into the power mode in which the device components are running at every moment, and they can be used to compare the performance of different operating systems executing the same tasks., This work was supported by the I+D+i program of the Generalitat Valenciana, R&D Project GV05/043, and Vicerrectorado of investigation, development and innovation of Universidad Politecnica de Valencia PAID-06-06-002-61. And Ministry of Science and Innovation of Spain, project COMONSENS.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Solar Energy Powered Autonomous Wireless Actuator Node for Irrigation Systems

  • Lajara Vizcaíno, José Rafael
  • Alberola, Jorge
  • Pelegri-Sebastia, Jose|||0000-0002-7392-3178
The design of a fully autonomous and wireless actuator node ("wEcoValve mote") based on the IEEE 802.15.4 standard is presented. The system allows remote control (open/close) of a 3-lead magnetic latch solenoid, commonly used in drip irrigation systems in applications such as agricultural areas, greenhouses, gardens, etc. The very low power consumption of the system in conjunction with the low power consumption of the valve, only when switching positions, allows the system to be solar powered, thus eliminating the need of wires and facilitating its deployment. By using supercapacitors recharged from a specifically designed solar power module, the need to replace batteries is also eliminated and the system is completely autonomous and maintenance free. The "wEcoValve mote" firmware is based on a synchronous protocol that allows a bidirectional communication with a latency optimized for real-time work, with a synchronization time between nodes of 4 s, thus achieving a power consumption average of 2.9 mW. © 2011 by the authors., This work was supported by the I + D + i program of the Generalitat Valenciana, R&D Project GV05/043, and the Vicerecorate of Investigation, Development and Innovation of Universidad Politecnica de Valencia PAID-06-06-002-61 and PAID-10-11.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A method for modeling the battery state of charge in wireless sensor networks

  • Lajara Vizcaíno, José Rafael
  • Pérez Solano, Juan José
  • Pelegri-Sebastia, Jose|||0000-0002-7392-3178
In this paper we propose a method for obtaining an analytic model of the battery State-of-Charge (SoC) in wireless sensor nodes. The objective is to find simple models that can be used to estimate accurately the real battery state and consequently the node lifetime. Running the model in the network nodes, we can provide the motes with the required information to implement applications that can be considered as battery-aware. The proposed methodology reduces the computational complexity of the model avoiding complicated electrochemical simulations and treating the battery as an unknown system with an output that can be predicted using simple mathematical models. At a first stage, during a setup period, the method starts with the measurement of several battery parameters under different environmental and operational conditions. After that, the method uses the previous collected data for building mathematical models, considering the linear regression or the multilayer perceptron as the most appropriated. Finally, the models are validated experimentally with new measures. Results show the suitability of the method that produces accurate and simple models, capable of being implemented even in low-cost and very constrained real motes, This work was supported by the I+D+i Program, Generalitat Valenciana, through the Research and Development under Project GV05/043 and in part by the Vicerrectorado of Investigation, Development and Innovation, Universidad Politecnica de Valencia, under Grant PAID-06-06-002-61.