Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Recovery of recycled acrylonitrile-butadiene-styrene, through mixing with styrene-ethylene/butylene-styrene

  • Peydro, M. A.|||0000-0002-8503-1505
  • Parres, F.|||0000-0002-1083-9526
  • Crespo, J.E|||0000-0003-1372-4289
  • Navarro Vidal, Raúl
Recovery of recycled acrylonitrile-butadiene-styrene (ABS) through mixing with styrene-ethylene/butylene-styrene (SEBS) has been studied in this paper. To simulate recycled ABS, virgin ABS was processed through 5 cycles, at extreme processing temperatures, 220 degrees C and 260 degrees C. The virgin ABS, the virgin SEBS, the recycled ABS and the mixtures were mechanically, thermally and rheologically characterized after the various cycles of reprocessing in order to evaluate their corresponding properties and correlate them with the number of cycles undergone. With these data and using Computer Aided Engineering (CAE) the injection process was simulated by obtaining the optimal injection process parameters. Mixtures were injected at two temperatures in a sensorised mold correlating the shrinkage of the parts with temperature. The results show that tensile strength of ABS remains practically constant as the number of reprocessing cycles increases, while in the material injected with SEBS the tensile strength decreases. Concerning the Charpy notched impact strength; the values of the ABS reprocessed at 220 degrees C remain more or less unchanged, while the values for 260 C show a significant decrease. The adhesion of the SEBS causes, in both cases, an increase in impact strength. DSC techniques enabled us to observe how the glass transition temperature (T-g) remains more or less constant regardless of the number of cycles or the temperature, whereas the crosslinking is much greater in the samples reprocessed at 260 C. Finally, the viscosity decreases with each cycle and this decrease becomes even more noticeable with the addition of SEBS, and also that the parts molded at lower temperatures have less shrinkage. (c) 2013 Elsevier B.V. All rights reserved., We would like to thank the Vice-Directorate of Research, Development and Innovation of the Polytechnic University of Valencia for the help granted to the project: "Ternary systems research applied to polymeric materials for the upgrading of waste styrene", Ref: 20091056 within the program of First Projects of Investigation (PAID 06-09) where this work is framed.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the thermal properties of Acrylonitrile Butadiene Styrene - High Impact Polystyrene blends with Styrene Ethylene Butylene Styrene

  • Peydro, M. A.|||0000-0002-8503-1505
  • Juárez Varón, David|||0000-0003-3251-8851
  • Sanchez-Caballero, Samuel|||0000-0001-5322-8082
  • Parres, F.|||0000-0002-1083-9526
[EN] A binary blend Acrylonitrile Butadiene Styrene ¿ High Impact Polystyrene (ABS-HIPS 50% wt) was prepared on a twin-screw extruder at 190-210 oC. The different properties were then analyzed using melt flow index (MFI), thermogravimetric analysis (TGA), and Fourier Transform Infrared spectroscopy (FTIR). FTIR analysis indicated heterogeneous distribution of the blend in injected pieces and SEM micrographs show heterogeneous distribution of both phase (ABS and HIPS). On the other hand, we have prepared ternary blends of ABS-HIPS-Styrene Ethylene Butylene Styrene (SEBS), varying the percentage of SEBS from 10 to 30 %wt using a twin screw extruder at 190-210oC. The addition of SEBS to the binary system (ABS-HIPS) allowed us to increase the ductile properties as well as reducing the viscosity., We would like to thank the Vice-Directorate of Research, Development and Innovation of the Polytechnic University of Valencia for the help granted to the project: “Ternary systems research applied to polymeric materials for the upgrading of waste styrene”, Ref: 20091056 within the program of First Projects of Investigation (PAID 06-09) where this work is framed.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Recuperación de plásticos reciclados mediante adicción de elastómeros termoplásticos. Caracterización mecánica y térmica, Thermoplastic elastomer addition for recovering recycled plastics. Mechanical and thermal characterization

  • Peydro, M. A.|||0000-0002-8503-1505
  • Parres, F.|||0000-0002-1083-9526
  • Crespo, J.E|||0000-0003-1372-4289
  • Navarro Vidal, Raúl
[EN] Recovery of recycled acrylonitrile butadiene styrene (ABS) through mixing with styrene-ethylene/butylene-styrene (SEBS) has been studied in this paper. To simulate recycled ABS, virgin ABS was processed through 5 cycles, at extreme processing temperatures, 220 degrees C and 260 degrees C. The virgin ABS, the virgin SEBS, the recycled ABS and the mixtures were mechanically and thermally characterized after the various cycles of reprocessing in order to evaluate their corresponding properties and correlate them with the number of cycles undergone. The results show that tensile strength of ABS remains practically constant as the number of reprocessing cycles increases, while in the material injected with SEBS the tensile strength decreases. Concerning the Charpy notched impact strength, the values of the ABS reprocessed at 220 degrees C remain more or less unchanged, while the values for 260 degrees C show a significant decrease. The adhesion of the SEBS causes, in both cases, an increase in impact strength. DSC techniques enabled us to observe how the glass transition temperature (Tg) remains more or less constant regardless of the number of cycles or the temperature, whereas the crosslinking is much greater in the samples reprocessed at 260 degrees C. As conclusion, it is suggested that the people who works handling and dealing with plastic that, when possible, use low temperatures of transformation of ABS instead of high temperatures. It is also recommended to recycle the ABS to those who work with it; to use 5% of SEBS added to the recycled ABS to recover the possible loss of properties., [ES] En este trabajo se estudia la recuperación de un Acrilonitrilo-Butadieno-Estireno (ABS) reciclado mediante mezcla con Estireno-Etileno/ Butadieno-Estireno (SEBS). Para simular el ABS reciclado se ha reprocesado ABS virgen durante cinco ciclos a las dos temperaturas extremas de procesamiento, 220ºC y 260ºC. Los materiales ABS virgen, SEBS virgen, ABS reprocesado y las mezclas han sido caracterizados mecánica y térmicamente para evaluar sus propiedades correspondientes y correlacionarlo con el número de ciclos de proceso. Los resultados muestran que la resistencia a tracción del ABS se mantiene prácticamente constante conforme aumenta el número de ciclos de reprocesado, en cambio, disminuye al aditivarlo con SEBS. Con respecto a la resistencia al impacto, los valores del ABS reprocesado a 220ºC permanecen prácticamente inalterables, mientras que para el reprocesado a 260ºC disminuyen de forma notable. La adhesión de SEBS provoca, en ambos casos, un incremento de energía de impacto. Las técnicas de DSC han permitido observar como la temperatura de transición vítrea se mantiene prácticamente constante independientemente del número de ciclos o de la temperatura; en cambio, el efecto de entrecruzamiento de las moléculas (crosslinking) es mucho mayor para las muestra reprocesadas a 260ºC. Como conclusión, se recomienda a los transformadores de plástico que, en lo posible, utilicen temperaturas de transformación del ABS bajas en vez de altas. También se recomienda a los transformadores que recuperen ABS, que utilicen un 5% de SEBS para mejorar las propiedades., Nos gustaría agradecer a la Subdirección de Investigación, Desarrollo e Innovación de la Universitat Politècnica de Valencia la ayuda concedida al proyecto: “la investigación de sistemas ternarios aplicados a los materiales poliméricos para la mejora de residuos de estireno”, Ref.: 20091056 en el programa de los primeros proyectos de investigación (PAID 06-09), donde este trabajo es un fragmento.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the Influence of adding styrene-ethylene/butadiene-styrene in acrylonitrile-butadiene-styrene and polyethylene blends

  • Peydro, M. A.|||0000-0002-8503-1505
  • Parres, F.|||0000-0002-1083-9526
  • Navarro Vidal, Raúl
  • Sanchez-Caballero, Samuel|||0000-0001-5322-8082
This work studies the recovery of two grades of acrylonitrile butadiene styrene (ABS) contaminated with low-density polyethylene (LDPE), by adding styrene ethylene/butadiene styrene (SEBS). To simulate contaminated ABS, virgin ABS was mixed with 1, 2, 4, and 8% of LDPE and then extruded at 220°C. After this, the ABS with the highest percentage of LDPE (8%) was mixed with 1, 2, 4, and 8% of SEBS and then extruded. Different blends were mechanically, rheologically, optically, and dimensionally characterized to study how different percentages of LDPE and SEBS modify their properties. The results obtained show how the tensile strength, Young modulus, elongation, and impact strength linearly decrease as the LDPE amount increases, for both natural and black ABS. Through the addition of SEBS to contaminated ABS, it is possible to improve its impact strength and elongation values nearly to those of virgin ABS. However, its tensile strength and Young modulus show no improvement, and even show a slight reduction. Regarding the rheological properties, the LDPE contamination in ABS causes a remarkable decrease in viscosity, and adding SEBS to the blend lowers its viscosity even further for both natural and black grades. This reduction is not a negative aspect, but rather quite the reverse, as the more fluid the material, the easier the mold injection process becomes. POLYM. ENG. SCI., 54:1313 1324, 2014. © 2013 Society of Plastics Engineers, Contract grant sponsor: "Subdireccion de Investigacion, Desarrollo e Innovacion de la Universitat Politecnica de Valencia" to the research project: "la investigacion de sistemas ternarios aplicados a los materiales polimericos para la mejora de residuos de estireno," Ref.: 20091056 belonging to the research program primeros proyectos de investigacion; contract grant number: PAID 06-09.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of styrene-ethylene-butylene-styrene on the properties of acrylonitrile butadiene styrene-high-impact polystyrene blends

  • Peydro, M. A.|||0000-0002-8503-1505
  • Parres, F.|||0000-0002-1083-9526
  • Navarro Vidal, Raúl
  • Crespo, J.E|||0000-0003-1372-4289
A binary blend of acrylonitrile butadiene styrene-high-impact polystyrene (ABS-HIPS 50% wt) was prepared on a twin-screw extruder at 190-210 degrees C. The different properties were then analyzed using tensile strength and impact tests, melt flow index, thermogravimetric analysis, and Fourier transform infrared spectroscopy (FTIR). The analysis of mechanical properties showed a decrease in elongation at break and impact strength. FTIR analysis indicated heterogeneous distribution of the blend in injected pieces and scanning electron microscopic images show heterogeneous distribution of both ABS and HIPS phase. On the other hand, by varying the percentage of styrene-ethylene-butylene-styrene (SEBS) from 10 to 30% wt using a twin-screw extruder at 190-210 degrees C, we have prepared ternary blends of ABS-HIPS-SEBS. The addition of SEBS to the binary system ABS-HIPS allowed us to increase the ductile properties (elongation at break and impact strength), as well as reducing the viscosity., The authors thank the Vice-Directorate of Research, Development and Innovation of the Polytechnic University of Valencia for the help rendered to the project: "Ternary systems research applied to polymeric materials for the upgrading of waste styrene", Ref: 20091056 within the program of First Projects of Research (PAID 06-09), where this work is framed.