Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the influence of the inlet boundary conditions in a LES simulation of internal flow in a diesel injector

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti Aldaravi, Pedro
In this paper the study of the behavior of the fuel flow through the injector nozzle using CFD tools is presented. Large Eddy Simulation will be used to model the internal flow turbulence in a Diesel fuel injector with velocities over 500 m/s. More specifically, the influence of boundary conditions applied to the model will be studied. The article analyzes the influence of the inlet boundary condition upon activation and maintenance of turbulent flow during the calculation. Carefully assessing which inlet boundary condition is more trustworthy in reality, for this the outlet velocity, pressure, turbulence and level of stabilization will be studied., This work has been funded by UNIVERSIDAD POLITECNICA DE VALENCIA from Spain, in the framework of the project "ESTUDIO DE LA INFLUENCIA DEL LEVANTAMIENTO DE AGUJA EN EL PROCESO DE INYECCION DIESEL'', Reference No. PAID-06-10-2362.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of cavitation phenomenon using different fuels in a transparent nozzle by hydraulic characterization and visualization

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Venegas Pereira, Óscar Hernando
In this paper the behavior of the internal flow under cavitating conditions and the influence of using different fuels is studied. For this purpose, a transparent nozzle (quartz plate) with a cylindrical orifice and four different fuels are used. The nozzle is installed in a pressurized rig with fuel in order to measure the mass flow and observe the flow inside the orifice using a special visualization technique with all fuels. Since the refractive index of the vapor bubbles of the fuel is different to the refractive index of the fuel in liquid state, the cavitation inside the nozzle can be appreciated. Pressure conditions at which the first bubbles inside the orifice appear are compared with the pressure conditions for mass flow collapse, showing that the beginning of the cavitation occurs before the mass flow collapse and that it depends both on the upstream and downstream pressure conditions and on the fluid viscosity used. Additionally it is observed that the mass flow collapse takes place once the cavitation is fully developed through the whole orifice and the presence of bubbles in the spray before the mass flow collapse indicating that the cavitation appears before the mentioned collapse., This work has been funded by Universidad Politecnica de Valencia from Spain, in the framework of the project "Estudio de la influencia del levantamiento de aguja en el proceso de inyeccion diesel", Reference No. PAID-06-10-2362. The authors would like to Jose Enrique del Rey (From CMT-Motores Termicos. Universidad Politecnica de Valencia.) for his collaboration in the experimental measurements.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flow regime effects over non-cavitating diesel injection nozzles

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • García Martínez, Antonio|||0000-0001-5783-4936
[EN] The research conducted and explained in this paper aims to explore and understand the influence of flow regime (laminar, transition or turbulent) inside diesel injector nozzles. For this purpose, an experimental study based on mass flow rate and momentum flux measurements on three convergent nozzles has been carried out. The combination of both types of measurement has been helpful to obtain information about the nature of the flow and its consequences on important variables, such as injection effective velocity and effective area of nozzle outlet orifices. As a main result of the investigation, and depending of the flow regime, a differentiated behaviour has been observed which was clearly reflected in the non-dimensional flow parameters defined and used through the study. © Author 2011., This work was supported by Project ‘Estudio de la influencia del levantamiento de aguja en el proceso de inyeccio´n die´sel’ from Universidad Polite´cnica de Valencia, Spain [grant number PAID-06-10-2362].