Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Methodology for optimizing biomass utilization for sustainable heat generation in chili dehydration plants: A case study in Zacatecas, Mexico

  • Vargas-Salgado, Carlos|||0000-0002-9259-8374
  • Alfonso-Solar, David|||0000-0003-0141-075X
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Águila-León, Jesús
  • Graterol-Bernadas, Orlando
  • Ortíz-Rodríguez, Nestor Manuel
[EN] This study presents a spatially integrated techno-economic methodology for replacing fossil fuels with residual biomass in agro-industrial heat generation, using chili dehydration plants in Zacatecas, Mexico, as a case study. The approach combines Geographic Information Systems (GIS), biomass resource assessment, transport network optimization, and energy system analysis to determine the technical, economic, and environmental feasibility of biomass-based heat supply. Forty-three dehydration plants comprising 504 drying tunnels were geolocated, and their thermal energy demands quantified, resulting in an annual biomass requirement of 44,899 t of dry woodchips. A GIS-based inventory identified 186 biomass collection points, mainly concentrated in the state's western forested areas. Spatial buffer and route-network analyses revealed that 46,023 tons of residual biomass per year are available within a 150 km service radius, sufficient to supply the entire network. A transport routing algorithm based on a distance-priority greedy heuristic was developed and benchmarked against the exact linear programming (LP) solution for the underlying capacitated transportation problem (186 origins, 43 destinations, 7,998 candidate routes), achieving an optimality gap of 1.79 %. The resulting logistics system has a total transportation cost of USD 839,335 per year and a total delivered biomass cost of approximately USD 1.89 million per year. The technical analysis indicates that replacing the existing fuel-oil-based boilers with biomass boilers and the existing LPG burners with biomass burners can reliably meet the plants' thermal demand. From an environmental perspective, the transition to biomass would reduce greenhouse-gas emissions (CO2e) by 81.3 % relative to the baseline of 35,050 t CO2/year, depending on the extent of seasonal biomass substitution. The results indicate the potential of residual biomass to provide a cost-effective, low-carbon heat source for chili dehydration in Zacatecas, highlighting the value of GIS-based planning and optimized logistics for regional bioenergy deployment., This project was supported by the projects "Uso de combustion de la biomasa como apoyo a un sistema de secado solar para mitigar las perdidas postcosecha en las zonas rurales de Zacatecas, Mexico" (AD2305). (01/01/24-31/12/25) Investigacion competitiva proyectos. UNIVERSIDAD POLITECNICA DE VALENCIA and Techno-economic Optimization of Hybrid Renewable Energy Flexible Systems Using Evolutionary Algorithms for Decarbonization in Cities (GENERGY) (PAID-11-25) (01/01/26-31/12/26). Investigacion competitiva proyectos. UNIVERSIDAD POLITECNICA DE VALENCIA. This work was also supported by: a grant of the Catedra de Transicion Energetica Urbana-funded by Ajuntament de Valencia-Valencia Innovation Capital and Fundacio Valencia Clima i Energia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Comprehensive Framework for the One-Point Probability Density Function of Solutions to Non-Autonomous Separable Random Differential Equations

  • Burgos-Simon, Clara|||0000-0001-6385-4263
  • Cortés, J.-C.|||0000-0002-6528-2155
  • Perez-Diukina, Cristina|||0009-0001-2218-7123
  • Rodríguez, F.
[EN] We develop a probabilistic framework to determine and estimate the one-point probability density function (1-PDF) of the solution of a broad class of non-autonomous separable random differential equations with random initial conditions. The approach is based on the random variable transformation (RVT) technique and reduces to the study of the distribution of a stochastic integral involving the random input or driving process. By assuming separability of the ODE and several analytical assumptions (invertibility of the state transformation, independence between sources of randomness, absolute continuity of the input process, and integrability of the density formula), the framework is built on two main theoretical results. First, a general density representation theorem provides sufficient conditions for the solution to be absolutely continuous, together with an explicit integral formula for its 1-PDF. Second, a convergence theorem proves that, when the driving process is replaced by an approximating one, the resulting density converges in L1(R) to the exact density, with an explicit error bound controlled by the L1 error of the integrated input. We then specialize the framework to four representative settings for the driving process: a Gaussian process, for which a closed-form 1-PDF is obtained, and three parametric families-affine-in-parameters representations, truncated Karhunen-Lo & egrave;ve, and generalized polynomial chaos expansions-for which tractable semi-explicit formulas are derived. In each case the 1-PDF is shown to be consistent with the prescribed initial condition, and all expressions admit numerical evaluation by standard quadrature and sampling. Finally, the framework is illustrated by four representative stochastic growth models, one per specialized setting, where all underlying hypotheses are verified explicitly and the computed analytical and semi-analytical densities are validated against Monte Carlo simulations., C. Burgos, J.C. Cortés and C.L. Pérez-Diukina have been supported by the grant PAID-11-25 funded by Universitat Politècnica de València and by grant PID2025-172735NB-I00 funded by MCIN/AEI. C. Burgos has been supported by the grant CIGE/2023/79 (Generalitat Valenciana). F. Rodríguez has been supported by the grant PID2021-125517OB-I00 funded by MCIN/AEI.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Large-eddy simulation study of direct injection ammonia sprays under engine-relevant conditions in flash boiling scenarios

  • Siddiqui, Waseeq
  • Karimkashi, Shervin
  • Hyvönen, Jari
  • Vuorinen, Ville
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
[EN] Ammonia, a promising fuel for internal combustion engines, is known to be highly susceptible to flash boiling under diesel engine-relevant conditions. Here, large-eddy simulation (LES) is used to examine ammonia sprays in ambient nitrogen under high injection pressure. A phase change model, combining boiling, flash boiling, and non-equilibrium evaporation, is utilized. Both single-hole and multi-hole nozzles are investigated. The spray models are calibrated according to various injection modeling parameters. The studied conditions encompass different modes of superheat levels (Rp) in non-reacting operating conditions. First, the single-hole configuration is studied under non-flash boiling conditions, and the spray setup is calibrated and validated. Second, the multi-hole configuration is used to validate the phase change model in flash boiling conditions. Third, numerical simulations are performed on a single-hole setup under high injection pressure to study transition flash boiling for 0.4 <= Rp <= 1.0. Fourth, Voronoi analysis is performed for the first time to compare the droplet clustering behavior under non-flash boiling and flash boiling engine-relevant conditions. The main observations of the study are as follows: (1) The present ammonia spray LES model can be calibrated to match experimental vapor penetration, liquid penetration length, and spray opening angle. (2) Intense flash boiling (low Rp) results in faster vapor penetration and stronger mixing due to faster inter-phase momentum transfer. (3) Lower values of Rp (intense flash boiling) lead to stronger cooling of the spray core, resulting in longer liquid penetration lengths. (4) Voronoi analysis indicates that sprays under non-flash boiling conditions, with slower rate of phase change, have a higher preferential concentration of droplets due to a broader observed range of droplet sizes and Stokes numbers., his study has been financially supported by the AINA project (project no.: 10424/31/2023) , supported by Business Finland. Waseeq acknowledges funding from Merenkulun saatio Grant number 20250137. Ville Vuorinen and Waseeq Siddiqui also acknowledge partial funding from the Research Council of Finland, Profi 7 Grant number 352955. Shervin Karimkashi acknowledges funding from Research Council of Finland project number 361479 (Wet-HyAm) . Gabriela Bracho acknowledges partial funding by grant PAID-11-25 by Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia, (UPV) . The authors would like to acknowledge CSC Finnish-IT Center for Science for providing the computational resources.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Transient and asymptotic distributions of vegetation under recurrent stochastic fires

  • Rodríguez, Francisco
  • Castro, M. Ángeles
  • Bautista, Susana
  • Cortés, J.-C.|||0000-0002-6528-2155
  • Perez-Diukina, Cristina|||0009-0001-2218-7123
[EN] Fire is a major ecological driver in forests worldwide, strongly influencing vegetation dynamics and ecosystem resilience. This work analyses the stochastic dynamics of tree biomass under recurrent fires with randomly distributed inter-fire times. We consider a model with logistic growth between fire events, each reducing biomass instantaneously by a fixed proportion, and we derive explicit expressions for the deviation of tree biomass from equilibrium after any number of fires. These expressions allow recursive computation of the moments of the transient distributions, including their means and variances, as well as the corresponding asymptotic moments under appropriate convergence conditions. To complete the probabilistic description of the fire dynamics, we apply the Random Variable Transformation method to compute the transient and asymptotic probability density functions of tree biomass of the pre-fire and post-fire events. The theoretical results are illustrated and discussed through examples considering exponentially distributed inter-fire times., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The work of F. Rodríguez, M.A. Castro and S. Bautista was partly funded by "MCIN/AEI/ 10.13039/501100011033 (Ministerio de Ciencia e Innovación/Agencia Estatal de Investigación) grant number PID2021-125517OBI00", and "Conselleria de Innovación, Universidades, Ciencia y Sociedad Digital, Generalitat Valenciana grant number CIPROM/2021/001". The work of J.C. Cortés and C.-L. Pérez has been partially supported by the grant PAID-11-25 funded by Universitat Politècnica de València and by grant PID2025-172735NB-I00 funded by MCIN/AEI.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multistage symbolic optimization for predictive thermal modeling of bifacial photovoltaic systems with solar tracking in tropical climates

  • Lara-Vargas, Fabian Alonso
  • Águila-León, Jesús
  • Sanchis-Gomez, Carlos
  • Vargas-Salgado, Carlos|||0000-0002-9259-8374
[EN] Accurate prediction of module temperature in bifacial photovoltaic (PV) systems equipped with single-axis solar tracking is critical for optimizing energy yield and mitigating thermal stress, particularly in tropical climates. However, existing empirical and data-driven approaches often lack physical interpretability or fail to adequately represent the nonlinear thermal behavior of operating PV modules. This study presents a novel multistage symbolic optimization (MSO) framework for predictive thermal modeling that addresses these limitations. The proposed two-level hierarchical approach first derives a physically interpretable symbolic equation using genetic algorithms (GA), followed by a second corrective symbolic regression stage in which GA and Alpha Evolution (AE) are evaluated as competing optimizers. This work presents a novel application of the AE algorithm to symbolic regression in PV thermal modeling. The methodology is validated using one year of high-resolution (5-min) operational data from a utility-scale bifacial PV plant with solar tracking in Colombia. The MSO-AE model achieved an R2 of 0.9439, an RMSE of 3.18 degrees C, and an MAE of 2.01 degrees C, outperforming the MSO-GA benchmark by 7.3% in MAE and 6.5% in RMSE, and surpassing recent single-stage symbolic regression models by 3.7-20%, while preserving closed-form, interpretable expressions suitable for real-time control applications. A field-derived heating coefficient of 0.034 degrees C/(W/m2) was identified. Observations show module temperatures exceeding 70 degrees C between 14:00 and 16:00, reducing electrical efficiency to 17.31%, corresponding to a 12.1% loss relative to standard test conditions. This thermal degradation resulted in average economic losses of USD 110.7 per hour during peak periods and an annual energy loss of 6738.6 MWh, equivalent to USD 336,929 at a benchmark electricity price of USD 50/MWh. These results define economic thresholds for thermal management investments in bifacial PV systems operating in tropical environments., FALV acknowledges the scholarship awarded by the Universidad Pontificia Bolivariana through RR No. 58 (October 25, 2023) to pursue studies at the Universitat Politecnica de Valencia. This work was supported by the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia through the PAID-11-25 program; the Catedra de Transicion Energetica Urbana, funded by the Ajuntament de Valencia-Valencia Innovation Capital and the Fundacio Valencia Clima i Energia; and the project "Renewable Energy System Integration and Digitalization Upskilling Initiative for Sustainable Buildings", financed by the European Union under Grant Agreement No. 101167278. JAL acknowledges support from the PROSNII 2025 program of the University of Guadalajara. CSG received support from the Valencian Innovation Agency through the European Regional Development Fund (ERDF) 2021-2026.The authors would like to thank Atlantica Sustainable SAS and Engineer Edison Ortega for their valuable support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Directly Imprinted Porous Titania Metasurfaces Supporting Guided Mode Resonance and Quasibound States in the Continuum

  • Panipinto, Matthew
  • Kravchenko, Ivan
  • Ryckman, Judson D.
  • Martínez-Gómez-Aldaraví, Andrea
  • Ortiz de Zárate-Díaz, David|||0000-0003-4127-9338
  • García-Rupérez, Jaime|||0000-0002-2036-0084
[EN] Resonant optical metasurfaces based on guided mode resonance (GMR) and quasibound states in the continuum (qBIC) offer compelling capabilities in sensing, structural color, and flat optics, but their fabrication typically requires multistep lithographic processing that limits scalability and practical deployment. Here, we demonstrate that direct nanoimprinting of mesoporous titania (pTiO2) thin films using custom-designed periodic grating stamps produces resonant metasurfaces in a streamlined two-step deposition-and-imprint process requiring no conventionalol lithography, etching, or cleanroom environment. The resulting structures support sharp, pitch-tunable GMR resonances observable in both transmission and reflection, with resonant wavelengths scaling linearly with grating pitch. Spatial arrangement of structures with systematically varied pitch and duty cycle enables pixel-level structural color image encoding with contrast visible under both broadband and laser illumination. Exposure to aerosolized deionized water produces fully reversible spatial resonance shifts, demonstrating label-free dynamic colorimetric vapor sensing. Finally, introduction of a lateral asymmetry parameter ¿ into the grating unit cell activates qBIC resonances. These results establish directly imprinted pTiO2 as a facile, scalable platform for visible-wavelength resonant metasurface devices., This study was supported by the National Science Foundation (2435833 and 2047015), PROMETEO (CIPROM/2022/14), and Universitat Politecnica de Valencia (MCIN/AEI/10.13039/501100011033PAID-11-25).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of Decarbonisation and Energy Efficiency Improvement Through Mycelium, Hygromorphic Wood and Hemp

  • Angulo Ibáñez, Quiteria
  • Cárcel-Carrasco, Javier|||0000-0003-2776-533X
  • Colmenero-Fonseca, Fabiola
  • Ros-Agulló, Ana
[EN] Decarbonising the building sector requires addressing both embodied carbon in materials and operational energy for indoor conditioning. This article critically reviews the potential of mycelium, hygromorphic wood and hemp as emerging natural materials for low-carbon construction, comparing them with conventional materials only within function-specific applications such as envelopes, insulation, non-load-bearing components and passive systems. Recent comparative literature shows that mycelium composites can reach thermal conductivities of 0.026-0.12 W/m & centerdot;K and densities of 51-280 kg/m3; in wood-mycelium formulations, an average density of 167.5 kg/m3 and climate impact of 2.13 kg CO2-eq/kg with a conventional electricity mix, reduced to 0.66 kg CO2-eq/kg with renewable energy, have been reported. Hemp shows typical densities of 140-540 kg/m3, conductivities of 0.061-0.12 W/m & centerdot;K, compressive strengths of 0.3-3.5 MPa and potentially negative climate performance of about -40 to -80 kg CO2-eq/m3, compared with +300 to +400 kg CO2-eq/m3 for conventional concrete. Hygromorphic wood is relevant not as insulation or a primary structural replacement, but as a passive actuation material for adaptive envelopes. Hemp is currently the most mature option, mycelium is promising for circular non-structural panels and insulation, and hygromorphic wood is an operational-modification strategy whose building-level energy benefits still require direct quantification. Cross-study comparisons should be interpreted as bounded ranges because composition, fabrication, testing and LCA (Life Cycle Assessment) system boundaries vary substantially across the literature., This article details some of the work carried out by the author, Q. AnguloIbáñez, in the following research projects: Zentropy-MICE. Remodelling a new concept of MICE sustainability under an urban entropy approach to enhance the legacy for Valencian citizens and optimise energy, matter, and information. Reference: EUI02-151. Commission of the European Communities; Technoeconomic Optimization of Flexible Hybrid Renewable Energy Systems Using Evolutionary Algorithms for Decarbonization in Cities (GENERGY). PAID-11-25. UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Novel Binary Classification Neural Network Optimized by theMosquito Mating Swarm Optimization Algorithm for PredictingMicrogrid OperationalModes

  • Águila-León, Jesús
  • Lara-Vargas, Fabian
  • Vargas-Salgado, Carlos|||0000-0002-9259-8374
  • Díaz-Bello, Dácil|||0000-0001-8416-9601
[EN] Integrating renewable energy sources presents technical challenges due to their variable nature, particularly in predicting and managing microgrid operational modes. Accurate identification of grid states¿interconnected or islanded¿is essential for maintaining stability and optimizing performance under fluctuating environmental conditions to meet energy demand. This work proposes a bio-inspired, optimized binary classification model based on Multi-Layer Perceptron Artificial Neural Networks (MLP-ANN), with the architecture and hyperparameters tuned using the novel Mosquito Mating Swarm Optimization (MMSO) algorithm, inspired by mosquito mating behavior and swarm dynamics. The model employs an MLP-ANN with a variable number of hidden layers and neurons per layer, configured to maximize classification accuracy by dynamically adjusting parameters, including the learning rate and regularization coefficients. Training utilizes k-fold cross-validation on experimental microgrid data. The MMSO approach is benchmarked against Particle Swarm Optimization (PSO), Genetic Algorithm (GA), and Grey Wolf Optimizer (GWO) to validate its effectiveness. Results show that the MMSO-optimized MLP-ANN achieved an 86.34% recall, 98.96% precision, and 92.29% accuracy, while minimizing the Mean Squared Error to 0.0206. The MMSO-optimized MLP-ANN model achieved competitive classification performance compared to the other algorithms evaluated; although no statistically significant differences in recall were observed among the optimizers (p = 0.22), the MMSO achieved the lowest MSE (0.0206). The MMSO was the only algorithm capable of discovering a four-layer architecture hidden within the same search space, evidencing superior exploration of deeper architectural regions of the solution space. These findings demonstrate the model¿s capacity to predict microgrid operational modes under variable conditions, highlighting the potential of integrating bio-inspired algorithms with neural networks for energy management systems. This approach could enhance the efficiency and reliability of integrating renewable energy sources into dynamic energy systems., This research was partially supported by the PROSNII 2025 program granted by the University of Guadalajara to Jesús Águila-León. In addition, the research was supported by the Vicerrectorado de Investigación of the Universitat Politècnica de València through the PAID-11-25 program. The authors also acknowledge the support of the Secretariat of Science, Humanities, Technology and Innovation (SECIHTI) of Mexico. The Institute of Energy Engineering at the Universitat Politècnica de València provided laboratory facilities and technical support for the experimental microgrid data collection.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Proyecto fin de carrera (BachelorThesis)

Oxidación electroquímica de nanoplásticos de metilmetacrilato, Electrochemical oxidation of methylmethacrylate nanoplastics, Oxidació electroquímica de nanoplàstics de metilmetacrilato

  • Maestro Martínez, Laura
[ES] En el presente trabajo final de grado se ha estudiado la eliminación de nanoplásticos de polimetilmetacrilato en disoluciones acuosas mediante oxidación electroquímica. Para ello se ha empleado ánodos comerciales (BDD y Ti superficialmente modificados con Pt) y ánodos desarrollados durante el trabajo final de grado (fieltros de Ti-Pt y electrodos 3D de Ti obtenidos mediante fabricación aditiva y modificados superficialmente con SnO2-Sb-Pt). Se han realizado estudios espectroscópicos (espectroscopía de fluorescencia, FTIR, entre otros) y morfológicos (FESEM, TEM, entre otros) para determinar el estado de degradación de los nanoplásticos tras la electrólisis. Además, se ha diseñado un prototipo y valorado el coste económico, así como los costes operativos del proceso.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Persimmon Powder from Discarded Fruits as a Potential Prebiotic to Modulate Gut Microbiota in Postmenopausal Women

  • Betoret Valls, María Ester|||0000-0002-9814-5042
  • Bueno-Bobadilla, Andrea Carolina
  • Betoret Valls, Noelia|||0000-0002-3326-8797
  • Jiménez-Hernández, Nuria
  • Duarte-Serna, Stevens
  • Artacho, Alejandro
  • Cruz, Irene
  • Gosalbes, María José
[EN] Faced with the challenge of reducing food waste, transforming discarded fruit into functional ingredients useful for the food industry is a valuable solution. Ingredients from fruit such as persimmons, which are rich in indigestible carbohydrates and bioactive compounds with antiradical capacity, could positively impact on the health of certain population groups due to their potential prebiotic effect. This study aimed to select the most suitable drying conditions and milling intensity for obtaining powdered persimmon ingredients with a prebiotic-like effects observed in vitro for postmenopausal women, and to evaluate this effect by considering the stimulation of health-promoting bacterial growth and short-chain fatty acids (SCFAs) production. First, the effect of the drying method (hot air drying at 60 and 70 ¿C, and freeze-drying) and grinding intensity on antiradical capacity, particle size, and the release of bioactive antiradical components into the intestinal lumen after an in vitro gastrointestinal digestion was determined. Next, the effect of these conditions on the microbiota composition of postmenopausal women was preliminary assessed in a batch colonic fermentation experiment for 24 h. The results showed that the ingredient dried with air at 70 ¿C had the highest phenol and flavonoid content, suffered the least degradation during in vitro gastrointestinal digestion and promoted the differential growth of fiber-degrader genera. Consequently, this was the ingredient selected as the most suitable. Lastly, the impact of this ingredient on the microbiota composition of 4 postmenopausal women has been evaluated in a long-term study using the Simulator of the Human Intestinal Microbial Ecosystem (SHIME®) coupled to high throughput sequencing. The growth stimulation of health-associated bacteria, such as Akkermansia muciniphila, Faecalibacterium prausnitzii or Phascolarctobacterium faecium, and the promotion of beneficial metabolic pathways, such as the sugar uptake-specific phosphotransferase system, sugar metabolism and propionate and isobutyrate production, were detected along 14 days of persimmon powder supplementation. A holistic framework for promoting human health while advancing environmental sustainability is represented by the combination of sustainable by-product valorization and microbiota-targeted functional food development., This study is part of the AGROALNEXT program and was supported by the Ministry of Science and Innovation (MCIN) and the Valencian Regional Government through funding from the European Next Generation funds (PRTR-C17.I1). This work was also supported by Conselleria de Innovación, Universidades, Ciencia y Sociedad Digital (Generalitat Valenciana) under a grant of the AICO 2023 program (CIAICO/2022/27).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Assessment of OME3 Combustion and Emission Reduction Under Oxy-Fuel Conditions in a CI Engine

  • Bruerre, Mathys
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Fernandes, Cássio S.
  • Lucchini, Tommaso
[EN] The use of renewable synthetic fuels is a suitable alternative for combustion-based systems. Their implementation can reduce pollutant emissions such as soot, CO and CO2, but NOx remains difficult to abate. The objective of this study is to evaluate the combination of Oxymethylene Ether-3 (OME3) with the oxy-fuel concept, hence operating without N2 and minimizing nitrogen oxides formation. For this purpose, advanced numerical simulations were used to investigate the effects of this strategy on combustion thermodynamics, efficiencies, and exhaust products. This model was adapted for the OME3 use, obtaining a reduction in soot production due to the fuel characteristics, but an increment of NOx emission. To overcome this issue, the oxy-fuel concept was implemented to remove N2 from the combustion process. The numerical analysis provides insights into combustion performance to enhance the comprehension of the factors responsible for emission reductions. Preliminary results have shown the feasibility to eliminate NOx while maintaining a near-zero soot production. Further evaluations pointed out a reduction of 90% and 30% of CO and HC, respectively, with a slight improvement (1%) of the combustion efficiency (98%) and Gross Indicated Efficiency (GIE) (36%). Overall, the present study demonstrates the feasibility of the concept and highlights its potential for further optimization and experimental validation., This research has been partly supported by grant PAID-11-25 by Vicerrectorado de Investigación de la Universitat Politècnica de València, (UPV). The author M. Bruerre thanks the Universitat Politècnica de València for his predoctoral contract, which is included within the framework of Programa de Apoyo para la Investigación y Desarrollo (PAID-01-22) del Vicerrectorado de Investigación.