Pasar al contenido principal

PRODUCCION Y MANIPULACION SEGURA DE NANOMATERIALES EN LA INDUSTRIA CERAMICA

PCIN-2015-173-C02-01

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos Programación Conjunta Internacional
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Subdirección General de Proyectos Internacionales
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Process-generated nanoparticles from ceramic tile sintering: Emissions, exposure and environmental release

  • Fonseca, Ana Sofía
  • Viana, Mar
  • Querol, Xavier
  • Francisco, I. de
  • Estepa, L. C.
  • Borrell, Carme
  • Lennikov, V.
  • Fuente, Germán F. de la
Under a Creative Commons license.-- et al., The ceramic industry is an industrial sector in need of significant process changes, which may benefit from innovative technologies such as laser sintering of ceramic tiles. Such innovations result in a considerable research gap within exposure assessment studies for process-generated ultrafine and nanoparticles. This study addresses this issue aiming to characterise particle formation, release mechanisms and their impact on personal exposure during a tile sintering activity in an industrial-scale pilot plant, as a follow-up of a previous study in a laboratory-scale plant. In addition, possible particle transformations in the exhaust system, the potential for particle release to the outdoor environment, and the effectiveness of the filtration system were also assessed. For this purpose, a tiered measurement strategy was conducted. The main findings evidence that nanoparticle emission patterns were strongly linked to temperature and tile chemical composition, and mainly independent of the laser treatment. Also, new particle formation (from gaseous precursors) events were detected, with nanoparticles < 30 nm in diameter being formed during the thermal treatment. In addition, ultrafine and nano-sized airborne particles were generated and emitted into workplace air during sintering process on a statistically significant level. These results evidence the risk of occupational exposure to ultrafine and nanoparticles during tile sintering activity since workers would be exposed to concentrations above the nano reference value (NRV; 4 × 10 cm), with 8-hour time weighted average concentrations in the range of 1.4 × 10 cm and 5.3 × 10 cm. A potential risk for nanoparticle and ultrafine particle release to the environment was also identified, despite the fact that the efficiency of the filtration system was successfully tested and evidenced a > 87% efficiency in particle number concentrations removal., This work was supported by the European Commission FP7 (FP7-PEOPLE-2012-ITN) Marie Curie ITN project no. 315760 (HEXACOMM) and by the Spanish MINECO (PCIN-2015-173-C02-01) under the frame of SIINN, the ERA-NET for a Safe Implementation of Innovative Nanoscience and Nanotechnology, through SIINN-ERANET project CERASAFE (id.:16). Additional support was provided by LIFE projects AIRUSE (LIFE11 ENV/ES/584), CERAMGLASS (LIFE11 ENV/ES/560) and LASERFIRING (LIFE09 ENV/ES/435)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanoparticle formation and emission during laser ablation of ceramic tiles

  • Salmatonidis, Apostolos
  • Viana, Mar
  • Pérez, Noemí
  • Alastuey, Andrés
  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Sanfélix, Vicenta
  • Monfort, Eliseo
Pulsed laser ablation (PLA) is a widely used technology, for surface structuring and tile decoration in the ceramic industry. During PLA, nanoparticles (NP <100 nm) are unintentionally released and may impact exposure. This work aims to understand the mechanisms controlling NP formation and release during ablation of different types of ceramic tiles, using different laser setups (near-IR and mid-IR). The measurements took place at laboratory and pilot-plant-scale, with varying laser wavelength, frequency, velocity, and pulse duration. In total, the combination of 4 types of ceramic tiles and 2 lasers was assessed. Particle number concentration and size distribution (SMPS with nano-DMA, DiSCmini, butanol-CPC) and particle mass concentration (DustTrak-DRX) were monitored. Samples were also collected for morphological and chemical characterization (TEM/EDX). High particle number concentrations were detected (3.5 *104/cm3 to 2.5 *106/cm3) for all of the tiles and under both laser setups. Particle formation (<10 nm) by nucleation was detected, and secondary amorphous SiO2 nanoparticles (>10 nm) were formed and released during ablation of the porcelain tiles. Different release mechanisms were identified: during ablation with the near-IR laser particles were emitted through melting and nucleation, while emissions from the mid-IR laser were attributed to melting and mechanical shockwaves. Particle number and mass emissions were dependent on the tile surface characteristics (e.g., porosity, crystallinity) and chemical properties. This work is potentially relevant from the point of view of exposure mitigation strategies in industrial facilities where PLA is carried out., The current work was carried out in the framework of the CERASAFE project (www.cerasafe.eu), with the support of SIINN ERA-NET (project id: 16), and is funded by the Spanish MINECO (PCIN-2015-173-C02-01). Partial support from project MAT2016-79866-R (AEI/FEDER, UE) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effectiveness of nanoparticle exposure mitigation measures in industrial settings

  • Salmatonidis, Apostolos
  • Sanfélix, Vicenta
  • Carpio, Pablo
  • Pawłowski, L.
  • Viana, Mar
  • Monfort, E.
Inhalation of airborne nanoparticles is a well-known source of potentially health-hazardous occupational exposures. Effective mitigation measures are necessary to reduce exposure, but also challenging to implement due to the different characteristics of each individual emission source and industrial scenario. The present paper describes four different exposure case studies in the ceramic industry and quantifies the effectiveness of mitigation strategies implemented during: ceramic tile processing by thermal spraying, laser ablation, the use of diesel engines, and tile firing. The mitigation measures for exposure reduction were tailored to each industrial scenario. The NP removal efficiency of source enclosure (partial/full) combined with local exhaust ventilation (LEV) were quantified to range between 65 and 85% when the enclosure was partial. The efficiency reached 99% with full enclosure and vigorous ventilation (Air Change per Hour; ACH = 132 h−1). The elimination of the source was the optimal strategy to minimize exposure in the case of diesel forklifts use. The conventional ceramic kilns used intensively (>10 years) generated high NP exposure concentrations (>106/cm3). Appropriate maintenance and enhanced sealing enabled the reduction of exposure down to 52% of the initial value. It must be added that technologically advanced kilns, enabled even greater NP reductions (down to 84%), compared to the conventional ones. This proves technological improvements can lead to significant reduction of work exposures. This work evidences the need for tailored mitigation measures due to the broad variety of potential sources and activities in industrial scenarios. The quantitative efficiency rates reported here may be valuable for the adequate parametrization of exposure prediction and risk assessment models. © 2019, The authors gratefully acknowledge the collaboration of the European Ceramics Centre in Limoges. This work was carried out in the framework of the CERASAFE project (www.cerasafe.eu), with the support of SIINN ERA-NET (project id: 16), and was funded by the Spanish MINECO (PCIN-2015-173-C02-01). Partial funding from the Generalitat de Catalunya (project number: AGAUR 2017 SGR41) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Particle size distributions and hygroscopic restructuring of ultrafine particles emitted during thermal spraying

  • Salmatonidis, Apostolos
  • Viana, Mar
  • Biskos, G.
  • Bezantakos, S.
We report measurements of the size, concentration, and hygroscopicity of ultrafine particles (UFPs) emitted during thermal spraying of ceramic coatings in an industrial setting. High concentrations (i.e., higher than 106 cm-3) of fractal-like UFPs were measured inside the spraying booths of the facility. The emitted UFPs were found to take up small amounts of water when exposed to elevated relative humidity (RH = 87%) within a Hygroscopic Tandem Differential Mobility Analyzer (HTDMA) system. The hygroscopicity of the sampled particles was distinguishably lower compared to those of the atmospheric background aerosol particles present in the breathing air. UFPs smaller than 90 nm that are produced by the thermal spraying process, exhibit hygroscopic factors less than unity in a systematic way. This behaviour indicates that the particles were irregularly shaped at dry conditions, and that they underwent a shape change (i.e., restructuring) upon humidification inside the HTDMA. The fractal-like structure of processemitted UFPs was further corroborated by Transmission Electron Microscopy (TEM) conducted on samples collected on site at dry conditions., The authors kindly acknowledge TM COMAS (http://www.tmcomas.com) for their committed cooperation. The current work was carried out in the framework of the CERASAFE project (www.cerasafe.eu), with the support of SIINN ERA-NET (project id: 16), and was funded by the Spanish MINECO (PCIN-2015-173-C02-01) and the respective French agency (Region Hauts de France). Partial funding from the “Generalitat de Catalunya” (project number: AGAUR 2017 SGR41) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterizing the Chemical Profile of Incidental Ultrafine Particles for Toxicity Assessment Using an Aerosol Concentrator

  • Viana, Mar
  • Salmatonidis, Apostolos
  • Bezantakos, S
  • Ribalta, Carla
  • Moreno, Natalia
  • Córdoba, Patricia
  • Cassee, F. R.
  • Boere, J.
  • Jordano, Juan
  • Teixeira, J. P.
  • Bessa, M. J.
  • Monfort, E.
Incidental ultrafine particles (UFPs) constitute a key pollutant in industrial workplaces. However, characterizing their chemical properties for exposure and toxicity assessments still remains a challenge. In this work, the performance of an aerosol concentrator (Versatile Aerosol Concentration Enrichment System, VACES) was assessed to simultaneously sample UFPs on filter substrates (for chemical analysis) and as liquid suspensions (for toxicity assessment), in a high UFP concentration scenario. An industrial case study was selected where metal-containing UFPs were emitted during thermal spraying of ceramic coatings. Results evidenced the comparability of the VACES system with online monitors in terms of UFP particle mass (for concentrations up to 95 µg UFP/m3) and between filters and liquid suspensions, in terms of particle composition (for concentrations up to 1000 µg/m3). This supports the applicability of this tool for UFP collection in view of chemical and toxicological characterization for incidental UFPs. In the industrial setting evaluated, results showed that the spraying temperature was a driver of fractionation of metals between UF (<0.2 µm) and fine (0.2-2.5 µm) particles. Potentially health hazardous metals (Ni, Cr) were enriched in UFPs and depleted in the fine particle fraction. Metals vaporized at high temperatures and concentrated in the UF fraction through nucleation processes. Results evidenced the need to understand incidental particle formation mechanisms due to their direct implications on particle composition and, thus, exposure. It is advisable that personal exposure and subsequent risk assessments in occupational settings should include dedicated metrics to monitor UFPs (especially, incidental)., This work was funded by SIINN ERA-NET (project id: 16), the Spanish MINECO (PCIN-2015-173-C02-01) and the French agency (Region Hauts de France). The Spanish Ministry of Science and Innovation (Project CEX2018-000794-S; Severo Ochoa) and the Generalitat de Catalunya (project number: AGAUR 2017 SGR41) provided support for the indirect costs for the Institute of Environmental Assessment and Water Research (IDAEA-CSIC). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Process-generated nanoparticles from ceramic tile sintering: Emissions, exposure and environmental release

  • Fonseca, A.S.
  • Maragkidou, A.
  • Viana, M.
  • Querol, X.
  • Hameri, K.
  • de Francisco, I.
  • Estepa, C.
  • Borrell, C.
  • Lennikov, V.
  • de la Fuente, G.F.
The ceramic industry is an industrial sector in need of significant process changes, which may benefit from innovative technologies such as laser sintering of ceramic tiles. Such innovations result in a considerable research gap within exposure assessment studies for process-generated ultrafine and nanoparticles. This study addresses this issue aiming to characterise particle formation, release mechanisms and their impact on personal exposure during a tile sintering activity in an industrial-scale pilot plant, as a follow-up of a previous study in a laboratory-scale plant. In addition, possible particle transformations in the exhaust system, the potential for particle release to the outdoor environment, and the effectiveness of the filtration system were also assessed. For this purpose, a tiered measurement strategy was conducted. The main findings evidence that nanoparticle emission patterns were strongly linked to temperature and tile chemical composition, and mainly independent of the laser treatment. Also, new particle formation (from gaseous precursors) events were detected, with nanoparticles <30 nm in diameter being formed during the thermal treatment. In addition, ultrafine and nano-sized airborne particles were generated and emitted into workplace air during sintering process on a statistically significant level. These results evidence the risk of occupational exposure to ultrafine and nanoparticles during tile sintering activity since workers would be exposed to concentrations above the nano reference value (NRV; 4 x 10(4) cm(-3)), with 8-hour time weighted average concentrations in the range of 1.4 x 10(5) cm(-3) and 5.3 x 10(5) cm(-3). A potential risk for nanoparticle and ultrafine particle release to the environment was also identified, despite the fact that the efficiency of the filtration system was successfully tested and evidenced a >87% efficiency in particle number concentrations removal.