Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Industrially viable method for producing all-polymer hydrophobic surfaces apt for slippery liquid-infused substrates

  • Afonso, Elisabet
  • Martínez-Gómez, Aránzazu
  • Tiemblo, Pilar
  • García, Nuria
For the sake of simplicity and scalability, we report a methodology to build a superhydrophobic textured upper layer on PVDF/PMMA blend films. The methodology is very easy to implement and does not need any fluorination as last step. In addition, it has been proved that this textured layer works as substrate for lubricant infused surfaces, with outstanding slippery properties. Knowing the importance of controlling the roughness profile to succeed in suitable wetting properties, we perform a thorough study of the roughness parameters by optical profilometry and establish their influence on the final wetting and slippery properties., The authors would like to acknowledge to the Spanish Ministry of Science and Innovation for funding (MAT2016-81001-P and PID2019- 109401 GB-I00). E.A. thanks to Spanish Ministry for the FPI Grant (BES- 2017-080057). The authors are in debt with Dr. J. Marco (IQFR-CSIC) and his team for XPS measurements and valuable discussions
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Addressing Manufacturability and Processability in Polymer Gel Electrolytes for Li/Na Batteries

  • Gregorio, Víctor
  • García, Nuria
  • Tiemblo, Pilar
Gel electrolytes are prepared with Ultra High Molecular Weight (UHMW) polyethylene oxide (PEO) in a concentration ranging from 5 to 30 wt.% and Li- and Na-doped 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (PYR14-TFSI) by a simple procedure consisting of dissolving PEO by melting it directly in the liquid electrolyte while stirring the blend. This procedure is fast, reproducible and needs no auxiliary solvents, which makes it sustainable and potentially easy to scale up for mass production. The viability of the up-scaling by extrusion has been studied. Extrusion has been chosen because it is a processing method commonly employed in the plastics industry. The structure and morphology of the gel electrolytes prepared by both methods have been studied by DSC and FTIR, showing small differences among the two methods. Composite gels incorporation high concentrations of surface modified sepiolite fibers have been successfully prepared by extrusion. The rheological behavior and ionic conductivity of the gels have been characterized, and very similar performance of the extruded and manually mixed gels is detected. Ionic conductivity of all the gels, including the composites, are at or over 0.4 mS cm<sup>−1</sup> at 25 °C, being at the same time thermoreversible and self-healing gels, tough, sticky, transparent and stretchable. This combination of properties, together with the viability of their industrial up-scaling, makes these gel electrolyte families very attractive for their application in energy storage devices., Spanish Ministry of Science and Innovation is gratefully acknowledged for funding through the project PID2019-109401GB-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Facile Preparation of Hydrophobic PET Surfaces by Solvent Induced Crystallization

  • Afonso, Elisabet
  • Martínez-Gómez, Aránzazu
  • Huerta, Andrea
  • Tiemblo, Pilar
  • García, Nuria
In this work, Polyethylene terephthalate (PET), one of the most widely consumed polymers, has been used as starting material for the development of non-stick surfaces through a fast, simple and scalable method based on solvent-induced crystallization to generate roughness, followed by a fluorination step. Several solvents were tested, among which dichloromethane was chosen because it gives rise to the formation of a particulate layer with rough topography. This particulate layer was covered by a polymer thin and smooth skin that must be removed to leave the rough layer as surface. The skin has been successfully removed by two strategies based on mechanical and chemical removal, each strategy producing different surface properties. A final treatment with a diluted solution of a fluorinated silane showed that it is possible to obtain PET surfaces with a water contact angle higher than 150 and low water adhesion. The reason behind this behavior is the development of a hierarchical rough profile during the induced polymer crystallization process. These surfaces were characterized by XRD, FTIR and DSC to monitor solvent induced crystallization. Topography was studied by SEM and optical profilometry. Wetting behavior was studied by measuring the contact angles and hysteresis., This research was funded by the Spanish Ministry of Science and Innovation and Universities MAT2016-81001-P and PID2019-109401 GB-I00
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploring chemical and structural features to tailor wetting properties of PVDF and PVDF/PMMA surfaces

  • Afonso, Elisabet
  • Martínez-Gómez, Aránzazu
  • Tiemblo, Pilar
  • García, Nuria
Superhydrophobicity has proven to be a useful tool to meet the needs of the new circular economy, even though its large-scale development continues to be challenging mainly due to the low affordability of micro and nanometric roughness generation methods. In this work, non-stick polymer materials based on Poly(vinylidene Fluoride), PVDF, and its blends with Poly(methyl methacrylate), PMMA, were developed by a simple, fast and industrially accessible solvent-induced method aligned with the ecodesign philosophy. The chemical and structural features that determine the wetting behavior are evaluated in 18 different surfaces, that present varied surface energy (blend composition from 100 to 60:40 PVDF:PMMA) and topography (controlled by the method conditions). Wetting behavior was analyzed by measuring the water contact angles and its hysteresis, whereas the roughness parameters were determined by optical profilometry. By tuning the blend composition and the solvent-induced process conditions, it was possible to obtain either superhydrophobic surfaces with contact angles higher than 160° and hysteresis lower than 5° or parahydrophobic surfaces with high contact angles and high water adhesion. The fundamental features of both wetting behaviors were critically discussed. In addition, a proof of concept of the industrial viability of the method on a fragment of a commercial piece made of PVDF was successfully carried out., The authors would like to acknowledge the Spanish Ministry for funding (PID2019-109401GB-I00). E.A. thanks to Spanish Ministry for the FPI Grant (BES-2017-080057).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparación y caracterización de compuestos de PLA con nanofibras de celulosa

  • Martínez-Gómez, Aránzazu
  • Hernansanz, Natalia
  • Afonso, Elisabet
  • Tiemblo, Pilar
  • García, Nuria
  • Vargas, F.
  • Bosch, C.
Se han preparado una serie de compuestos de ácido poliláctico (PLA) con celulosa microfibrilada (MFC) con el objetivo de buscar una mejora en las propiedades mecánicas, térmicas y de transporte de gases del polímero. Para ello, en primer lugar, se modificó la superficie de las microfibras para hacerlas más compatibles con la matriz polimérica. Se ensayaron distintos métodos de mezclado, llegando a la conclusión de que es posible obtener buenas dispersiones mediante procesado en fundido, siempre que se parta de un concentrado de microfibras con el polímero. La caracterización de los materiales dio como resultado un aumento en los módulos de almacenamiento respecto del PLA puro, incluso a bajos (4% en peso) contenidos de MFC. La estabilidad térmica no se ve deteriorada por la incorporación de las microfibras y por lo que se refiere a las propiedades barrera, se registraron valores de permeabilidad a distintos gases ligeramente inferiores en comparación con el PLA puro., A series of composites from polylactic acid (PLA) and microfibrillated cellulose (MFC) were prepared with the aim of searching for an improvement in mechanical, thermal and gas barrier properties. Firstly, the microfibers surface was modified to make them more compatible with the polymer matrix. After testing different methods of mixing, the conclusion is that it is possible to achieve fair dispersions by melt compounding if a masterbatch is used. The mechanical characterization of the samples showed that the storage modulus of the composites increased compared to neat PLA even at low MFC content (4 wt.%). On the other hand, the thermal stability did not deteriorate in the composites, and the permeability to different gases was slightly lower than that of neat PLA., Los autores agradecen al Ministerio de Ciencia e Innovación por la concesión del proyecto PID2019-109401GB-I00. Asimismo, agradecen al IVACE (Instituto Valenciano de Competitividad Empresarial) que a través del programa Promece 2022 ha cofinanciado parte de los resultados expuestos en este trabajo.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Superficies antiadherentes y sostenibles

  • Hernández-Rivas, M.
  • Martínez-Gómez, A.
  • Afonso, E.
  • Tiemblo, Pilar
  • García, Nuria
Las superficies altamente repelentes a líquidos de distinta naturaleza han cobrado gran importancia debido a sus propiedades específicas, como autolimpieza, antihielo y anti-incrustación. En la actualidad se conocen diferentes tipos de superficies antiadherentes inspiradas en la Naturaleza. Entre ellas, las inspiradas en la hoja de loto han sido las más utilizadas durante las últimas décadas. Sin embargo, este tipo de superficies presenta algunas limitaciones, principalmente su baja estabilidad mecánica y, en general, su poca eficacia frente a líquidos de baja tensión superficial. Es por ello que ha surgido la necesidad de diseñar nuevos materiales antiadherentes, por ejemplo, los inspirados en la planta carnívora en forma de jarra llamada Nepenthes. Estos materiales son conocidos como SLIPS del inglés Slippery Liquid Infused Porous Surfaces (Superficies porosas infiltradas con líquidos deslizantes). En nuestra búsqueda de nuevos materiales con alta repelencia a los líquidos, el objetivo principal de este trabajo es crear una superficie deslizante infiltrada con líquidos libre de flúor, utilizando para ello métodos simples y fácilmente escalables. Con este propósito, se eligió el ácido poli (láctico) (PLA) como material de partida debido no solo a su biodegradabilidad sino también a su origen biobasado, Water and oil highly repellent surfaces have gained great importance due to their specific properties such as self-cleaning, anti-icing, and anti-biofouling. Nowadays, different types of non-stick surfaces inspired by Nature are known. Among them, those inspired by the lotus leaf have been the most studied and used in recent decades. However, this type of surface has limitations, the main ones being its low mechanical stability and, in general, its poor effectiveness against liquids with low surface tension. That is why the need to design new and improved non-stick materials has arisen, inspired by the pitcher-shaped carnivorous plant called Nepenthes. These materials are known as SLIPS for Slippery Liquid Infused Porous Surfaces. In our search for new materials with extreme liquid repellency, the main objective of this work is to create a fluorine-free slippery liquid infused surface, using simple and easily scalable methods. For this purpose, polylactic acid (PLA) was chosen as the raw material due not only to its biodegradability but also to its biobased origin, Los autores agradecen la financiación recibida del Ministerio de Ciencia e Innovación mediante el proyecto PID2019-109401GB- I00. Además, M. Hernández-Rivas agradece al MINECO la concesión de un contrato FPI (PRE2020-094915) para la realización de su tesis doctoral.