Pasar al contenido principal

MANTENIMIENTO Y CONTROL OPTIMO DE VEHICULOS HIBRIDOS DE TRANSPORTE URBANO MEDIANTE DATOS DEL CONTEXTO OPERACIONAL

PID2020-119691RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Energy Management of Hybrid Electric Urban Bus by Off-Line Dynamic Programming Optimization and One-Step Look-Ahead Rollout

  • Tormos, B.|||0000-0002-8852-3783
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Bares-Moreno, Pau|||0000-0001-9672-0819
  • Pinto, Douglas
[EN] Due to the growing air quality concern in urban areas and rising fuel prices, urban bus fleets are progressively turning to hybrid electric vehicles (HEVs) which show higher efficiency and lower emissions in comparison with conventional vehicles. HEVs can reduce fuel consumption and emissions by combining different energy sources (i.e., fuel and batteries). In this sense, the performance of HEVs is strongly dependent on the energy management strategy (EMS) which coordinates the energy sources available to exploit their potential. While most EMSs are calibrated for general driving conditions, this paper proposes to adapt the EMS to the specific driving conditions on a particular bus route. The proposed algorithm relies on the fact that partial information on the driving cycle can be assumed since, in the case of a urban bus, the considered route is periodically covered. According to this hypothesis, the strategy presented in this paper is based on estimating the driving cycle from a previous trip of the bus in the considered route. This initial driving cycle is used to compute the theoretical optimal solution by dynamic programming. The obtained control policy (particularly the cost-to-go matrix) is stored and used in the subsequent driving cycles by applying one-step look-ahead roll out, then, adapting the EMS to the actual driving conditions but exploiting the similarities with previous cycles in the same route. To justify the proposed strategy, the paper discusses the common patterns in different driving cycles of the same bus route, pointing out several metrics that show how a single cycle captures most of the key parameters for EMS optimization. Then, the proposed algorithm (off-line dynamic programming optimization and one-step look-ahead rollout) is described. Results obtained by simulation show that the proposed method is able to keep the battery charge within the required range and achieve near-optimal performance, with only a 1.9% increase in fuel consumption with regards to the theoretical optimum. As a reference for comparison, the equivalent consumption minimization strategy (ECMS), which is the most widespread algorithm for HEV energy management, produces an increase in fuel consumption with respect to the optimal solution of 11%., This research was funded by Ministerio de Ciencia e Innovacion, through the Proyectos I+D+i 2020 Program, grant number PID2020-119691RB-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application assessment of UV-vis and NIR spectroscopy for the quantification of fuel dilution problems on used engine oils

  • Macian Martinez, Vicente
  • García-Barberá, Antonio
  • Tormos, B.|||0000-0002-8852-3783
  • Balaguer-Reyes, Adbeel|||0000-0002-4777-9539
[EN] Fuel dilution in engine oil is a frequent problem in internal combustion engines (ICE); its main consequence is the reduction of the oil viscosity, decreasing lubrication film strength, and causing a negative impact on friction and wear. The standard and more precise methods for assessing fuel content in oil are based on chromatographic analysis (e.g., ASTM D3524, ASTM D7593), requiring high-cost equipment and highly qualified personnel. This work performed a study to propose an alternative method for quantifying diesel fuel dilution in used engine oil by UV¿vis and NIR spectroscopy. The samples for the study were prepared from used oil from six different vehicles with various mileages. According to the results obtained in this study, NIR spectroscopy proved to be the most suitable method for the quantification of diesel fuel in used engine oils. Furthermore, the use of NIR spectroscopy combined with multivariate calibration methods could predict the fuel concentration of the samples used for validating the model. The best predictive model for the quantification was obtained by Partial Least Squares Regression, which achieved a Root Mean Squared Error of prediction of 0.436% and a coefficient of determination of 0.9435. In comparison, the parameters for Principal Component Regression were 1.049% and 0.8441, respectively., Acknowledgments This work has been partially supported by grant PID2020-119691RB-100 funded by MCIN/AEI/10.13039/501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Explainable AI Using On-Board Diagnostics Data for Urban Buses Maintenance Management: A Study Case

  • Tormos, B.|||0000-0002-8852-3783
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Sánchez-Márquez, Ramon Eduardo
  • Carballo, Jose Luis
[EN] Industry 4.0, leveraging tools like AI and the massive generation of data, is driving a paradigm shift in maintenance management. Specifically, in the realm of Artificial Intelligence (AI), traditionally ¿black box¿ models are now being unveiled through explainable AI techniques, which provide insights into model decision-making processes. This study addresses the underutilization of these techniques alongside On-Board Diagnostics data by maintenance management teams in urban bus fleets for addressing key issues affecting vehicle reliability and maintenance needs. In the context of urban bus fleets, diesel particulate filter regeneration processes frequently operate under suboptimal conditions, accelerating engine oil degradation and increasing maintenance costs. Due to limited documentation on the control system of the filter, the maintenance team faces obstacles in proposing solutions based on a comprehensive understanding of the system¿s behavior and control logic. The objective of this study is to analyze and predict the various states during the diesel particulate filter regeneration process using Machine Learning and explainable artificial intelligence techniques. The insights obtained aim to provide the maintenance team with a deeper understanding of the filter¿s control logic, enabling them to develop proposals grounded in a comprehensive understanding of the system. This study employs a combination of traditional Machine Learning models, including XGBoost, LightGBM, Random Forest, and Support Vector Machine. The target variable, representing three possible regeneration states, was transformed using a one-vs-rest approach, resulting in three binary classification tasks where each target state was individually classified against all other states. Additionally, explainable AI techniques such as Shapley Additive Explanations, Partial Dependence Plots, and Individual Conditional Expectation were applied to interpret and visualize the conditions influencing each regeneration state. The results successfully associate two states with specific operating conditions and establish operational thresholds for key variables, offering practical guidelines for optimizing the regeneration process., This work has been partially supported by grant PID2020-119691RB-100 funded by MCIN/AEI/10.13039/501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Supervisory controller for minimizing fuel consumption and NOx emissions of plug-in hybrid electric vehicles operating in zero-emission zones

  • Uberti-Pinto, Douglas
  • Frasci, Emmanuele
  • Arsie, Ivan
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Nakaema-Aronis, Andre|||0000-0001-9599-7736
[EN] This paper introduces a supervisory controller designed for Plug-in Hybrid Electric Vehicles (PHEVs) to minimize total energy consumption and tailpipe NOx emissions while adhering to Zero Emission Zone (ZEZ) constraints. The case study exploits historical driving cycle data from an urban bus route in Zurich to analyze trip correlations, where a ZEZ restriction was added to assess the vehicle performance under such conditions. A PHEV bus model was built, integrating the powertrain and After-Treatment System (ATS), where an electric heater is included to mitigate NOx emissions. The supervisory controller is tasked with determining the optimal power split and the electric heater power to ensure adherence to feasible operating conditions along the route. Historical driving cycle data analysis demonstrates that the speed profiles along the selected route exhibit similarities. This observation is leveraged by a Dynamic Programming (DP) optimization, where an arbitrary bus trip is employed to generate a cost-to-go matrix. Then, the resulting cos-to-go matrix was indexed by the position in the route and is used on the real-time controller by applying the one-step look-ahead roll-out algorithm. Simulation results demonstrate the controller effectiveness in addressing ZEZ restrictions, presenting a trade-off between energy consumption and tailpipe NOx emissions. A benchmark was carried out, comparing the results obtained with the DP solution as the baseline, assuming perfect knowledge of driving cycle disturbances, revealing a 7% increase in tailpipe NOx emissions and a 1.3% increase in fuel consumption compared to the theoretical minimum and fulfilling the ZEZ restrictions in all the cases., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the Agencia Estatal de Investigacion of Spain through the project PID2020-119691RB-I00, entitled ''Mantenimiento Y ControlOptimo De Vehiculos Hibridos De Transporte Urbano Mediante Datos Del Contexto Operacional''.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Cooperative driving for automated vehicles: a two-layer algorithm in a full context awareness mixed traffic scenario

  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Bares-Moreno, Pau|||0000-0001-9672-0819
  • Nakaema-Aronis, Andre|||0000-0001-9599-7736
  • Trintinaglia-Perin, Augusto|||0000-0002-4915-2852
[EN] Driving advisory usually require a-priori information about the route, which can be provided by context awareness technologies, such as vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) connectivity. This study presents a cooperative driving algorithm by formulating an optimal control problem (OCP) and solving it with a non-linear Model Predictive Control (MPC) approach with two steps. First, the OCP is solved by Dynamic Programming (DP), providing the cost-to-go (CTG) from any pair time-state to the end of the problem. The CTG can be used as a terminal cost for the MPC to be solved recursively during the route considering traffic as a disturbance in a short horizon. Secondly, the optimization is solved iteratively: at any time-step the first vehicle is solved assuming that the rest follow the traffic prediction algorithm. The process continues sequentially until all the vehicles have been solved, while the traffic prediction is replaced by the optimal trajectories of the vehicles that have been previously computed. Different prediction horizons, mixed traffic levels and the scheduling policy to solve the different vehicles are evaluated. Results suggest that the cooperative driving algorithm can reduce the fleet fuel consumption by up to 35%, while covering the same route in a similar time., This research has been partially funded by the Agencia Estatal de Investigacion of Spain through the project PID2020-119691RB-I00, entitled Mantenimiento Y Control Optimo De Vehiculos Hibridos De Transporte Urbano Mediante Datos Del Contexto Operacional and by the Conselleria d Innovacio, Universitats, Ciencia i Societat Digital de la Generalitat Valenciana with the funding program Santiago Grisolıa (GRISOLIA/2023-CIGRIS/2022/065).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of PHEV energy management in emission-controlled environments through non-linear model predictive control and long-term cost evaluation

  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Bares-Moreno, Pau|||0000-0001-9672-0819
  • Nakaema-Aronis, Andre|||0000-0001-9599-7736
  • Pinto, Douglas Uberti
[EN] As regulations on pollutant emissions rapidly advance and the demand for sustainable mobility grows, the necessity for innovative technological solutions becomes crucial. To address these challenges, this research focuses on the development and application of a control-oriented model for plug-in hybrid electric vehicles (PHEVs), aimed at minimizing fuel consumption and NOx emissions while respecting operational constraints imposed during the vehicle's operation. Accordingly, the model developed integrates the powertrain and the after-treatment system based on non-linear model predictive control (NLMPC) framework, strategically modulating the power distribution between the internal combustion engine (ICE) and the electric motor (EM), along with the ammonia injection strategy for effective NOx abatement and fuel savings. To overcome the finite horizon limitations of NLMPC, an offline dynamic programming (DP) was embedded, improving predictive capabilities through a cost-to-go matrix that reflects optimal control actions under specific conditions. This hybrid approach combines the global optimization of DP with the real-time flexibility of NLMPC, allowing dynamic adjustments to vehicle operation in response to real-time data and future scenarios. The applicability of the proposed strategy is demonstrated in routes containing a zero-emission zone and vehicles with different battery sizes, underlining its adaptability to complex driving conditions and distinct vehicle designs, thereby demonstrating its potential for significant contributions to sustainable mobility solutions., This research has been partially funded by the Agencia Estatal de Investigacion of Spain through the project PID2020-119691RB-I00, entitled "Mantenimiento Y Control Optimo De Vehiculos Hibridos De Transporte Urbano Mediante Datos Del Contexto Operacional".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A multi-objective energy management optimization for a hybrid electric bus covering an urban route

  • Tormos, B.|||0000-0002-8852-3783
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Bares-Moreno, Pau|||0000-0001-9672-0819
  • Pinto, Douglas
[EN] The development of electrified vehicles is a promising step toward energy savings, emissions reduction, environmental protection, and more sustainable economic growth. In the case of hybrid electric vehicles (HEVs), the energy management strategy (EMS) is essential for their efficiency and energy consumption. Typically, EMS employs rule-based strategies calibrated to general driving conditions. So, this paper proposes to calibrate the EMS of an urban hybrid electric bus that covers a particular route by taking advantage of past driving information. The EMS computes the percentage of the vehicle power demand that must be supplied by each of the sources (fuel and battery) and also controls the heating, ventilating and air conditioning (HVAC) system to achieve cabin thermal comfort. The proposed approach is based on employing an optimal solution by dynamic programing in a previous loop covered by the bus in the considered route. Then, the cost-to-go matrix is stored and used in the following trips by applying the one-step look-ahead rollout, taking profit from the similarities of the loops in the route. To compare and evaluate the performance of the proposed algorithm, a benchmark was carried out by employing the widespread equivalent consumption minimization strategy (ECMS) approach, combined with rule-based strategies in the HVAC control system. Finally, the pareto front presents the trade-off between cabin temperature control performance and total fuel consumption, allowing to compare and evaluate the different EMS calibrations., This research was funded by Ministerio de Ciencia e Innovacion, through the Proyectos I + D + i 2020 Program, grant number PID2020-119691RB-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Eco-Driving Optimization of a Signalized Route With Extended Traffic State Information

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Bares-Moreno, Pau|||0000-0001-9672-0819
  • Trintinaglia-Perin, Augusto|||0000-0002-4915-2852
[EN] Literature suggests that driving style and conditions play a major role in vehicle energy consumption. In this sense, this work focuses on vehicle speed planning using information from the environment, through vehicle-to-infrastructure (V2I), and from nearby vehicles, with vehicle-to vehicle (V2V) information to reduce fuel consumption over a signalized route. By knowing the traffic lights scenario of the route in advance and the current position and speed of the preceding vehicle, the proposed algorithm decides the ego-vehicle speed profile during a given horizon to minimize fuel consumption. The proposed strategy solves the optimal control problem (OCP) in each prediction horizon through dynamic programming (DP) with a simplified model. The scenario and the optimal solution are updated periodically to make up for scenario prediction and modeling uncertainties. Experimental tests were conducted on a test bench to evaluate the fuel consumption of the simulated speed profile when compared to the preceding vehicle. Results show that a reduction of almost 20% in fuel consumption is possible without penalizing travel time while keeping it real-time (RT) feasible., This research has been partially funded by the Agencia Estatal de Investigacion of Spain through the project PID2020-119691RB-I00, entitled" Mantenimiento Y Control Optimo De Vehiculos Hibridos De Transporte Urbano Mediante Datos Del Contexto Operacional".