Pasar al contenido principal

ACELERADORES BASADOS EN FPGAS PARA REDES NEURONALES PROFUNDAS SUFICIENTEMENTE CONFIABLES PARA SISTEMAS DE AUTOMOCION

PID2020-120271RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

BAFFI: a bit-accurate fault injector for improved dependability assessment of FPGA prototypes

  • Tuzov, Ilya|||0000-0002-1980-0708
  • de-Andrés-Martínez, David|||0000-0002-4744-3795
  • Ruiz, Juan Carlos|||0000-0001-7678-3513
  • Hernández Luz, Carles|||0000-0003-1192-6223
[EN] FPGA-based fault injection (FFI) is an indispensable technique for verification and dependability assessment of FPGA designs and prototypes. Existing FFI tools make use of Xilinx essential bits technology to locate the relevant fault targets in FPGA configuration memory (CM). Most FFI tools treat essential bits as black-box, while few of them are able to filter essential bits on the area basis in order to selectively target design components contained within the predefined Pblocks. This approach, however, remains insufficiently precise since the granularity of Pblocks in practice does not reach the smallest design components. This paper proposes an open-source FFI tool that enables much more fine-grained FFI experiments for Xilinx 7-series and Ultrascale+ FPGAs. By mapping the essential bits with the hierarchical netlist, it allows to precisely target any component in the design tree, up to an individual LUT or register, without the need for defining Pblocks (floorplanning). With minimal experimental effort it estimates the contribution of each DUT component into the resulting dependability features, and discovers weak points of the DUT. Through case studies we show how the proposed tool can be applied to different kinds of DUTs: from small-footprint microcontrollers, up to multicore RISC-V SoC. The correctness of FFI results is validated by means of RT-level and gate-level simulation-based fault injection., This work has received funding from (i) ECSEL Joint Undertaking (JU) under grant agreement No 877056, (ii) Agencia Estatal de Investigacion from Spain under grant agreement no. PCI2020-112092, (iii) European Unions Horizon 2020 research and innovation programme under grant agreement no. 871467, and (iv) Grant PID2020-120271RB-I00 funded by MCIN/AEI/ 10.13039/501100011033. Carles Hernandez is partially supported by Spanish Ministry of Science, Innovation and Universities under Ramon y Cajal, fellowship No. RYC2020-030685-I.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Proposal of an ECC-based Adaptive Fault-Tolerant Mechanism for 16-bit data words

  • Gracia-Morán, Joaquín|||0000-0001-9715-8960
  • Saiz-Adalid, Luis-J.|||0000-0002-4868-2050
  • Baraza-Calvo, Juan-Carlos|||0000-0001-7692-2309
  • Gil Tomás, Daniel Antonio|||0000-0001-9225-1998
  • Gil, Pedro|||0000-0002-9364-7385
[EN] With the integration scale level reached in CMOS technology, memory systems provide a great storage capacity, but at the price of an augment in their fault rate. In this way, the probability of experiencing Single Cell Upsets or Multiple Cell Upsets have risen. Error Correction Codes (ECC) are broadly employed to protect memory systems. Though, the inclusion of an ECC in a computer system adds, in each memory word, some extra bits used to detect and/or correct errors. In addition, encoding and decoding circuitries must be added, introducing overheads in area, delay, and power consumption. Usually, when an ECC-based fault tolerance mechanism is designed, its fault tolerance properties cannot be modified. However, in some applications, current memory systems can suffer a variable fault rate during their operation. Thus, it seems very interesting that this mechanism would be able to adapt to these variable fault conditions. This work proposes an Adaptive Fault-Tolerant mechanism based on ECC. This mechanism can adapt to different fault conditions, being able to correct and/or detect single and multiple bits in error. The Adaptive Fault-Tolerant mechanism proposed uses a unique encoder, that is, it is not necessary to re-encode the data to change the error coverage., Proyecto PID2020-120271RB-I00 financiado por MCIN/AEI /10.13039/501100011033
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Reversing FPGA Architectures for Speeding up Fault Injection: does it pay?

  • Tuzov, Ilya|||0000-0002-1980-0708
  • de-Andrés-Martínez, David|||0000-0002-4744-3795
  • Ruiz, Juan Carlos|||0000-0001-7678-3513
[EN] Although initially considered for fast system prototyping, Field Programmable Gate Arrays (FPGAs) are gaining interest for implementing final products thanks to their inherent reconfiguration capabilities. As they are susceptible to soft errors in their configuration memory, the dependability of FPGA-based designs must be accurately evaluated to be used in critical systems. In recent years, research has focused on speeding up fault injection in FPGA-based systems by parallelising experimentation, reducing the injection time, and decreasing the number of experiments. Going a step further requires delving into the FPGA architecture, i.e. precisely determining which components are implementing the considered design (mapping) and which are exercised by the considered workload (profiling). After that, fault injection campaigns can focus on those components actually used to identify critical ones, i.e. those leading the target system to fail. Some manufacturers, like Xilinx, identify those bits in the FPGA configuration memory that may change the implemented design when affected by a soft error. However, their correspondence to particular components of the FPGA fabric and their relationship with the implementation-level model are yet unknown. This paper addresses whether the effort of reversing an FPGA architecture to filter out redundant and unused essential bits pays in terms of experimental time. Since the work of reversing the complete architecture of an FPGA is titanic, as the first step towards this ambitious goal, this paper focuses on those elements in charge of implementing the combinational logic of the design (Look-Up Tables). The experimental results that support this study derive from implementing three soft-core processors on a Zynq SoC FPGA and show the interest of the proposal., Grant PID2020-120271RB-I00 funded by MCIN/AEI/10.13039/501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Hybrid Technique Based on ECC and Hardened Cells for Tolerating Random Multiple-Bit Upsets in SRAM Arrays

  • Gil Tomás, Daniel Antonio|||0000-0001-9225-1998
  • Saiz-Adalid, Luis-J.|||0000-0002-4868-2050
  • Gracia-Morán, Joaquín|||0000-0001-9715-8960
  • Baraza-Calvo, Juan-Carlos|||0000-0001-7692-2309
  • Gil, Pedro|||0000-0002-9364-7385
[EN] MBU is an increasing challenge in SRAM memory, due to the chip's large area of SRAM, and supply power scaling applied to reduce static consumption. Powerful ECCs can cope with random MBUs, but at the expense of complex encoding/decoding circuits, and high memory redundancy. Alternatively, radiation-hardened cell is an alternative technique that can mask single or even double node upsets in the same cell, but at the cost of increasing the overhead of the memory array. The idea of this work is to combine both techniques to take advantage of their respective strengths. To reduce redundancy and encoder/decoder overheads, SEC Hamming ECC has been chosen. About hardened cells, well-known and robust DICE cells, able to tolerate one node upset, have been used. To assess the proposed technique, we have measured the correction capability after a fault injection campaign, as well as the overhead (redundancy, area, power, and delay) of memory and encoding/decoding circuits. Results show high MBU correction coverages with an affordable overhead. For instance, for very harmful 8-bit random MBUs injected in the same memory word, more than 80% of the cases are corrected. Area overhead values of our proposal, measured with respect to double and triple error correction codes, are less than x1.45. To achieve the same correction coverage only with ECCs, redundancy, and overhead would be much higher., This work was supported by the Ministerio de Ciencia e Innovación/Agencia Estatal de Investigación by project MCIN/AEI/10.13039/501100011033 under Grant PID2020-120271RB-I00
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An Open Source Methodology to Emulate Transient Faults in ASIC Storage Cells Using AMD Ultrascale¿ FPGAs

  • Tuzov, Ilya|||0000-0002-1980-0708
  • de-Andrés-Martínez, David|||0000-0002-4744-3795
  • Ruiz, Juan Carlos|||0000-0001-7678-3513
  • Hernández Luz, Carles|||0000-0003-1192-6223
[EN] The dependability assessment of critical systems must consider the emulation of transient faults, as they pose an important dependability threat for modern VLSI designs. FPGA-based systems are dominated by bit-flips in configuration memory (CM), which are relatively easy to emulate using partial runtime reconfiguration (RTR) FPGA fault injection (FFI) approaches. However, when FPGA is used as an ASIC prototyping platform, transient fault models representative of ASIC designs must be considered, such as bit-flips in sequential logic cells (Flip-Flops and on-chip RAM blocks). Existing RTR-FFI approaches do not adequately cover these faults, as they require the orchestrated manipulation of multiple CM bits for each target logic cell, and the location of these CM bits is unknown (not documented) for modern FPGA generations. This work experimentally formalises the mapping of the necessary CM bits, proposes an enhanced RTR-FFI methodology to emulate bitflips in registers and on-chip RAMs of current-generation AMD Ultrascale+ FPGAs, and provides an upgraded publicly available open source FFI tool (BAFFI, https://gitlab.com/selene-riscv-platform/DAVOS) supporting the proposed methodology. The validity of the proposed FFI approach is demonstrated by comparison with gate-level simulation-based fault injection in a case study of two soft-core processors (MC8051 and NOEL-V)., The ISOLDE project no. Grant 101112274 is supported by the Sponsor Chips Joint Undertaking and its members Austria, Czechia, France, Germany, Italy, Romania, Spain, Sweden and Switzerland. Project DEFADAS, Grant PID2020-120271RB-I00 funded by Sponsor MCIN/AEI/10.13039/501100011033. Carles Hernández is partially supported by the Sponsor Spanish Ministry of Science, Innovation, and Universities under Ramón y Cajal fellowship No. Grant RYC2020-030685-I and the Sponsor Valencian government IFAC project (Grant CISEJI/2022/30).