Pasar al contenido principal

GENERADORES TERMOELECTRICOS AUTONOMOS PARA VIGILANCIA VOLCANICA

PID2021-124014OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD PUBLICA DE NAVARRA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced behaviour of a passive thermoelectric generator with phase change heat exchangers and radiative cooling

  • Astrain, David
  • Jaramillo-Fernandez, Juliana
  • Araiz, Miguel
  • Francone, Achille
  • Catalán, Leyre
  • Jacobo-Martín, Alejandra
  • Alegría, Patricia
  • Sotomayor Torres, C. M.
Heat exchangers are essential to optimize the efficiency of Thermoelectric Generators (TEGs), and heat pipes without fans have proven to be an advantageous design as it maintains the characteristic robustness of thermoelectricity, low maintenance and lack of moving parts. However, the efficiency of these heat exchangers decreases under natural convection conditions, reducing their heat transfer capacity and thus thermoelectric power production. This work reports on a novel heat exchanger that combines for the first time, phase change and radiative cooling in a thermoelectric generator to improve its efficiency and increase the production of electrical energy, specially under natural convection. For this, two thermoelectric generators with heat-pipes on their cold sides have been tested: one with the radiative coating and the other without it. Their thermal resistances have been determined and the electric power output was compared under different working conditions, namely, natural convection and forced convection indoors and outdoors. The experimental tests show a clear reduction of the heat exchanger thermal resistance thanks to the radiative coating and consequently, an increase of electric production 8.3 % with outdoor wind velocities of 1 m/s, and up to 54.8 % under free convection conditions. The application of the radiative surface treatment is shown to result in a more stable electrical energy production, suppressing the drastic decrease in the generated electric power that occurs in thermoelectric generators when they work under free convection., The authors acknowledge the support of the Spanish Ministry of Science, Innovation and Universities, and the European Regional Development Fund, under grants PID2021-124014OB-I00 (VIVOTEG), TED2021-129359B-I00 (GEOTEG), PGC2018-101743-B-I00 (SIP) and RTI2018-093921-A-C44 (SMOOTH). The ICN2 authors thank the CERCA Program/Generalitat de Catalunya. Open access funding provided by Universidad Pública de Navarra., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced behaviour of a passive thermoelectric generator with phase change heat exchangers and radiative cooling

  • Astrain, David|||0000-0002-6987-0640
  • Jaramillo Fernández, Juliana|||0000-0002-4787-3904
  • Araiz, Miguel|||0000-0002-7674-0078
  • Francone, Achille|||0000-0001-7757-9901
  • Catalán, Leyre|||0000-0003-0140-6689
  • Jacobo-Martín, Alejandra|||0000-0003-2404-2881
  • Alegría, Patricia
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Heat exchangers are essential to optimize the efficiency of Thermoelectric Generators (TEGs), and heat pipes without fans have proven to be an advantageous design as it maintains the characteristic robustness of thermoelectricity, low maintenance and lack of moving parts. However, the efficiency of these heat exchangers decreases under natural convection conditions, reducing their heat transfer capacity and thus thermoelectric power production. This work reports on a novel heat exchanger that combines for the first time, phase change and radiative cooling in a thermoelectric generator to improve its efficiency and increase the production of electrical energy, specially under natural convection. For this, two thermoelectric generators with heat-pipes on their cold sides have been tested: one with the radiative coating and the other without it. Their thermal resistances have been determined and the electric power output was compared under different working conditions, namely, natural convection and forced convection indoors and outdoors. The experimental tests show a clear reduction of the heat exchanger thermal resistance thanks to the radiative coating and consequently, an increase of electric production 8.3 % with outdoor wind velocities of 1 m/s, and up to 54.8 % under free convection conditions. The application of the radiative surface treatment is shown to result in a more stable electrical energy production, suppressing the drastic decrease in the generated electric power that occurs in thermoelectric generators when they work under free convection.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Design and optimization of thermoelectric generators for harnessing geothermal anomalies: a computational model and validation with experimental field results

  • Alegría Cía, Patricia
  • Catalán Ros, Leyre
  • Araiz Vega, Miguel
  • Erro Iturralde, Irantzu
  • Astrain Ulibarrena, David
Thermoelectric generators have been recently proved to be a feasible alternative to harness hot dry rock fields with very promising results transforming the geothermal heat into electricity. This research deepens in the study of these generators, developing a versatile computational model that serves as a tool to design and optimize this type of thermoelectric generators. This tool is important to develop this thermoelectric technology on a large scale, to produce clean and renewable electrical energy especially in the Timanfaya National Park, in Lanzarote (Spain), where some of the most important shallow geothermal anomalies in the world are located, in order to promote self-consumption in this zone. However, it could be employed in other areas with different boundary conditions. The model, based in the finite difference method applied to the thermal-electrical analogy of a geothermal thermoelectric generator, has been validated with the experimental field results of two thermoelectric generators installed in two different zones of geothermal anomalies. It has achieved a relative error of less than 10% when predicting the power and between 0.5–1.6% in the annual energy generation, what makes it a very reliable and useful computational tool. The developed model has been employed for the first time to estimate the electrical energy that could be generated if harnessing the characterized area of anomalies in Lanzarote. Here, given the continuity of geothermal energy, 7.24 GWh per year could be generated, which means annually 1.03 MWh/m2., We would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE, Spain under the grants TED2021-129359B-I00 and PID2021-124014OB-I00. We would also like to acknowledge the support of the Official School of Industrial Engineers of Navarre, Spain with the scholarship Fuentes Dutor. Open access funding provided by the Public University of Navarre, Spain .
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Thermoelectric generator for high temperature geothermal anomalies: experimental development and field operation

  • Alegría Cía, Patricia
  • Catalán Ros, Leyre
  • Araiz Vega, Miguel
  • Casi Satrústegui, Álvaro
  • Astrain Ulibarrena, David
In the current climate and energy context, it is important to develop technologies that permit increase the use of renewable sources such as geothermal energy. Enhancing the use of this renewable source is particularly important in some places, due to its availability and the enormous dependence on fossil fuels, as is the case of the Canary Islands. This work proposes the use of thermoelectric generators with heat exchangers working by phase change to transform the heat from the shallow high temperature geothermal anomalies on the island of Lanzarote directly into electricity, since the use of conventional geothermal power plants would not be possible because they would damage the protected environment. To bring this proposal to reality, this work has succeeded in developing and field-installing a geothermal thermoelectric generator that operates without moving parts thanks to its phase-change heat exchangers. This robust generator do not require maintenance nor auxiliary consumption, and produces a minimal environmental impact, it is noiseless, and the use of water as working fluid makes it completely harmless. The developed device consists of a thermosyphon as hot side heat exchanger, thermoelectric modules and cold side heat exchangers also based in phase change. Tests were carried out in the laboratory at various heat source temperatures and varying the number of thermoelectric modules. It was determined that installing more modules decreases the efficiency per module (from 4.83% with 4 modules to 4.59% with 8 modules at a temperature difference between sources of 235 °C), but for the number of modules tested the total power increases, so the field installation was carried out with 8 modules. After the good results in the laboratory, it was satisfactorily installed at Timanfaya National Park (Lanzarote, Spain) in a borehole with gases at 465 °C. This generator presents a maximum output power of 36 W (4.5 W per module), and is generating 286.94 kWh per year, demonstrating the great potential of the developed thermoelectric generators to build a larger-scale renewable installation., Spanish State Research Agency and FEDER-UE funds under the grants TED2021-129359B-I00 and PID2021-124014OB-I00. Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Experimental and computational investigation of passive heat exchangers to enhance the performance of a geothermal thermoelectric generator

  • Pascual Lezaun, Nerea
  • Alegría Cía, Patricia
  • Araiz Vega, Miguel
  • Martínez Echeverri, Álvaro
  • Astrain Ulibarrena, David
Thermoelectric devices hold significant promise for generating electricity from geothermal heat, enabling the powering of measuring equipment in remote locations without the need for moving parts. Nevertheless, most developed geothermal thermoelectric generators employ fans and pumps to enhance heat transfer, thereby compromising the robustness and reliability inherent to thermoelectricity. Furthermore, there is a lack of research on passive heat exchangers for geothermal thermoelectric generators, particularly in studying their operation under a wide range of meteorological conditions. Therefore, this paper conducts a comprehensive analysis of passive heat exchangers for the cold side of the generators. Phase-change-based heat exchangers differing in their length and fluid are studied experimentally, along with a fin dissipator. Additionally, the influence of wind velocity on heat transfer and mechanical requirements is further explored through a Computational Fluid Dynamics model. The most significant outcome is quantifying the impact of the design parameters and operational variables on the electrical production of the thermoelectric generator. Accordingly, this research aims to broaden the application of these generators to extreme environments, such as Deception Island in Antarctica. Under average operational conditions, generators incorporating 400 mm water heat pipes generate 0.95 W per thermoelectric module, while those incorporating heat pipes with methanol achieve an average of 0.70 W. Moreover, water and methanol-based systems produce 120% and 60% more power than generators using a fin dissipator. Nonetheless, for temperatures beyond -6.5 °C, water might freeze and the methanol-based heat exchangers become more suitable., The authors would like to acknowledge the support of the Spanish State Research Agency and EFEDER-UE, Spain for funding under the PID2021-124014OB-I00 research project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Tesis doctoral (DoctoralThesis)

Design and optimisation of thermoelectric generators for supplying electrical power to autonomous volcanic monitoring stations

  • Pascual Lezaun, Nerea
La monitorización volcánica es clave para la comprensión de los procesos geodinámicos y para la detección temprana de posibles erupciones. Sin embargo, en la actualidad, alrededor del 30% de los volcanes activos carece de vigilancia continua debido, principalmente, a su localización remota y a la dificultad para obtener un suministro eléctrico ininterrumpido. La energía fotovoltaica, tecnología predominante en este ámbito, presenta limitaciones severas en volcanes sometidos a condiciones meteorológicas adversas, como acumulación de nieve, y a periodos prolongados sin radiación solar, lo que impide garantizar un suministro eléctrico fiable durante todo el año. Paralelamente, la tecnología termoeléctrica no ha logrado una penetración relevante en el mercado de la generación eléctrica, ya que su baja eficiencia la hace poco competitiva frente a otras alternativas cuando el objetivo principal es minimizar el coste de la energía. No obstante, en aplicaciones donde la prioridad no es la eficiencia sino la robustez, la fiabilidad y la autonomía, la termolectricidad se convierte en una alternativa especialmente atractiva, al permitir la conversión directa de energía térmica en electricidad sin necesidad de emplear componentes móviles y con un mantenimiento mínimo. En este contexto, la tesis propone el uso de generadores termoeléctricos geotérmicos pasivos que aprovechan el calor de fumarolas volcánicas de baja temperatura. Las fumarolas, ampliamente presentes en entornos volcánicos, constituyen una fuente térmica disponible de forma continua, y la termolectricidad aporta un conjunto de características que ninguna otra tecnología energética reúne simultáneamente para esta aplicación. Esta propuesta conlleva un reto tecnológico significativo. La mayor parte de generadores termoeléctricos incorporan componentes activos en sus intercambiadores de calor, como bombas o ventiladores, para incrementar el rendimiento del sistema, pero en la monitorización volcánica remota, la robustez y la autonomía son prioritarias. Por consiguiente, en esta aplicación resulta fundamental prescindir de los componentes móviles y recurrir exclusivamente a intercambiadores de calor pasivos. Esta restricción impone un gran desafío, ya que aprovechar saltos térmicos moderados mediante intercambio de calor pasivo limita el potencial de producción eléctrica y exige un diseño altamente optimizado. Además, dicho diseño debe ser capaz de operar en ambientes adversos para garantizar su aplicabilidad a cualquier volcán del mundo. Para asegurar la viabilidad técnica de la tecnología propuesta, se desarrolla una metodología que combina experimentación en laboratorio, validación en campo y optimización computacional. En primer lugar, se estudian intercambiadores de calor pasivos en el lado frío del sistema, evaluando su comportamiento en un amplio rango de temperaturas ambiente y velocidades de viento. El análisis determina que, en promedio, los generadores con intercambiadores de cambio de fase incrementan la potencia eléctrica producida en un 70% frente a una configuración equivalente basada en disipadores de aletas. Entre los intercambiadores de cambio de fase, la configuración basada en agua alcanza una producción media un 36% superior frente a la que emplea metanol como fluido de trabajo, pero la aplicabilidad del agua queda condicionada por el riesgo de congelación, que puede producirse a partir de temperaturas ambiente de −6.5 ◦C. Con el fin de combinar el máximo rendimiento del agua con la resistencia a la congelación que aporta el metanol en condiciones próximas al umbral de congelación, se ha desarrollado un intercambiador innovador que integra heat pipes de ambos fluidos. Asimismo, se estudian intercambiadores de tipo heat pipe y termosifón en el lado caliente del sistema. Mediante la combinación de los intercambiadores de calor desarrollados, se evalúan experimentalmente diferentes configuraciones de generadores termoeléctricos bajo un amplio rango de condiciones ambientales, alcanzándose potencias de hasta 1.2W por módulo termoeléctrico. La viabilidad de la tecnología se valida en condiciones reales mediante la instalación y monitorización de un sistema compuesto por cuatro generadores termoeléctricos geotérmicos pasivos en Isla Decepción. Esta campaña constituye la primera demostración mundial de generación eléctrica continua a partir de calor geotérmico en la Antártida, alcanzando una potencia media de 4.4W. En base a los resultados obtenidos en campo, se evalúa computacionalmente el impacto de la optimización geométrica de los módulos termoeléctricos en la producción energética. La optimización multiparámetro y multiobjetivo permite incrementos de hasta un 12.6% respecto a los módulos comerciales empleados en la instalación. Asimismo, se identifica la reducción de la resistencia térmica de los intercambiadores de calor como el factor determinante para maximizar el rendimiento del sistema, ya que incrementa la potencia generada, amplia el margen de mejora mediante optimización y reduce el volumen de material semiconductor necesario. A partir de este análisis, se derivan criterios de diseño generales y transferibles, aplicables a generadores termoeléctricos que operan con fuentes térmicas de baja temperatura. El trabajo realizado en esta tesis doctoral, en el marco del proyecto PID2021-124014OB-I00, ha permitido alcanzar una solución tecnológica inédita, robusta, fiable y modular al reto actual del suministro energético para la monitorización volcánica continua. Esta solución se basa en generadores termoeléctricos geotérmicos pasivos con intercambiadores de calor basados en el cambio de fase y viene acompañada de criterios de diseño sólidos y transferibles, que facilitan su implantación en volcanes activos de todo el mundo. Su instalación en el volcán de Isla Decepción, en la Antártida, ha supuesto ya un avance sin precedentes, permitiendo por primera vez disponer de datos geológicos en tiempo real durante un año completo. De esta forma, se demuestra el enorme potencial de esta tecnología como fuente energética estable para redes de vigilancia en entornos aislados, reforzando la capacidad de anticipación y previsión de posibles erupciones., Volcanic monitoring is essential for improving the understanding of geodynamic processes and for the early detection of potential eruptions. Nevertheless, approximately 30% of active volcanoes lack continuous surveillance, primarily due to their remoteness and the dificulty of ensuring an uninterrupted power supply. Photovoltaic power, the most widely deployed solution in this field, is subject to substantial constraints at volcanoes affected by harsh meteorological conditions, such as snow accumulation, and by extended periods with minimal or no solar irradiance, thereby precluding a reliable year-round electricity supply. In parallel, thermoelectric technology has yet to achieve substantial market penetration in power generation. This is principally attributable to its relatively low efficiency, which makes it uncompetitive relative to alternative technologies when the main objective is minimising the cost of energy. However, in scenarios where efficiency is secondary to robustness, reliability, and autonomy, thermoelectric conversion becomes an attractive option, as it enables the direct conversion of thermal energy into electricity without moving parts and with minimal maintenance. In this context, the present Ph. D. dissertation proposes the use of geothermal passive thermoelectric generators that harness heat from low temperature volcanic fumaroles. Fumaroles, which are widespread in volcanic environments, provide a continuously available thermal resource, and thermoelectric generation offers a combination of attributes that no other energy technology can simultaneously provide for this application. This approach entails a substantial technological challenge. Most thermoelectric generators employ active components in their heat exchangers, such as pumps or fans, to improve system performance, whereas robustness and autonomy are paramount in remote volcanic monitoring. Consequently, the proposed application requires the elimination of moving components and exclusive reliance on passive heat exchangers. This constraint is demanding because the exploitation of modest temperature differences through passive heat exchangers limits achievable electrical output and, therefore, requires a highly optimised design. In addition, the system must operate reliably in harsh environments in order to be applicable to a wide range of volcanic settings worldwide. To establish the technical viability of the proposed technology, a methodology combining laboratory experimentation, field validation, and computational optimisation is developed. First, passive heat exchangers on the cold side of the system are investigated, with their performance assessed across a wide range of ambient temperaturas and wind speeds. The analysis shows that, on average, generators employing phase change heat exchangers increase electrical power output by approximately 70% as compared with an equivalent configuration based on fin dissipators. Among the phase change heat exchangers, the water-based configuration achieves an average power output 36% higher than that obtained with methanol as the working fluid. However, the applicability of water is constrained by the risk of freezing, which may occur at ambient temperaturas below −6.5 ◦C. To combine the high performance of water with the resistance to freezing provided by methanol in conditions close to the freezing threshold, an innovative heat exchanger integrating water and methanol based heat pipes has been developed. In addition, heat pipe and thermosyphon type heat exchangers on the hot side are examined. By combining the developed heat exchangers, several thermoelectric generator configurations are evaluated experimentally under a broad range of environmental conditions, achieving power outputs of up to 1.2W per thermoelectric module. The viability of the technology is validated under field conditions through the installation and monitoring of a system comprising four geothermal passive thermoelectric generators on Deception Island. This deployment represents the world's first demonstration of continuous electricity generation from geotermal heat in Antarctica, achieving an average power output of 4.4W. Building on the field results, the impact of geometric optimisation of thermoelectric modules on energy production is evaluated computationally. The multi-parameter and multi-objective optimisation approach identifies potential increases of up to 12.6% compared with the commercial modules used in the installation. In addition, reducing the thermal resistance of the heat exchangers is shown to be the determining factor, since it maximises system performance, as it increases generated power, expands the scope for improvement through module optimisation, and reduces the required volume of semiconductor material. On this basis, general and transferable design criteria are derived for thermoelectric generators operating with low temperature thermal sources. The work presented in this Ph. D. dissertation, conducted within the framework of project PID2021-124014OB-I00, provides a novel, robust, reliable, and modular technological solution to address the current challenge of energy supply for continuous volcanic monitoring. The proposed solution is based on geothermal passive thermoelectric generators incorporating phasechange-based heat exchangers and is supported by rigorous and transferable design criteria that facilitate deployment on active volcanoes worldwide. Its installation on Deception Island in Antarctica has already represented an unprecedented advance, enabling the transmission of real-time geological data for the first time over a complete year. Therefore, the Ph. D. dissertation demonstrates the considerable potential of this technology as a continuous and reliable power source for monitoring networks in isolated environments, thereby strengthening the capability to anticipate and forecast possible eruptions., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa Ofiziala (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Multi-parameter and multi-objective optimisation of thermoelectric modules for enhanced performance in geothermal passive generators

  • Pascual Lezaun, Nerea
  • Martínez Echeverri, Álvaro
  • Erro Iturralde, Irantzu
  • Astrain Ulibarrena, David
Geometrical optimisation studies of thermoelectric modules often overlook the significant influence of system-level components, particularly heat exchangers. This research addresses this critical gap by developing an integrated system-level optimisation approach, applied to a geothermal passive thermoelectric generator installed in Antarctica. The methodology is based on the premise that the thermal and electrical phenomena are interdependent, demanding a holistic design. For the first time, a comprehensive multi-objective, multi-parameter computational model for geometric optimisation of modules is presented, which incorporates all thermoelectric effects, temperature-dependent properties, and all system components. The framework simultaneously maximises electrical power output and minimises semiconductor material volume by adjusting the thermocouple length and cross-sectional area to their optimal values. Application to the Antarctic installation demonstrated that geometric optimisation yields energy production improvements from 3.7% to 12.6% with respect to the commercial modules used in the installation. These improvements correspond to configurations with leg lengths of 0.11 cm and 0.27 cm and cross-sectional areas of 0.023 cm2 and 0.06 cm2, respectively. Crucially, an extended analysis revealed that while the source temperature difference does not affect optimal geometric parameters, the thermal resistances are paramount. Reducing the sum of heat exchanger thermal resistances by 26% increases optimisation potential by 60%, while also reducing semiconductor volume by 18.5%. These results demonstrate a system-level optimisation approach is essential. Findings indicate efforts must first prioritise optimising heat exchangers for the lowest thermal resistance. Subsequently, the optimal module geometry is determined by maximising the thermocouple cross-sectional area before adjusting the length for optimal thermal matching., The authors would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE under the grants PID2024-162043OB-I00 and PRE2022-103787. The authors would also like to acknowledge the Thermoelectric and Electrochemical Systems and Technology Group at the Jet Propulsion Laboratory, supervised by Dr. Thierry Caillat, for their insightful comments and valuable discussions. Open access funding provided by the Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Enhanced behaviour of a passive thermoelectric generator with phase change heat exchangers and radiative cooling

  • Astrain Ulibarrena, David
  • Jaramillo-Fernández, Juliana
  • Araiz Vega, Miguel
  • Francone, Achille
  • Catalán Ros, Leyre
  • Jacobo-Martín, Alejandra
  • Alegría Cía, Patricia
  • Sotomayor-Torres, Clivia M.
Heat exchangers are essential to optimize the efficiency of Thermoelectric Generators (TEGs), and heat pipes without fans have proven to be an advantageous design as it maintains the characteristic robustness of thermoelectricity, low maintenance and lack of moving parts. However, the efficiency of these heat exchangers decreases under natural convection conditions, reducing their heat transfer capacity and thus thermoelectric power production. This work reports on a novel heat exchanger that combines for the first time, phase change and radiative cooling in a thermoelectric generator to improve its efficiency and increase the production of electrical energy, specially under natural convection. For this, two thermoelectric generators with heat-pipes on their cold sides have been tested: one with the radiative coating and the other without it. Their thermal resistances have been determined and the electric power output was compared under different working conditions, namely, natural convection and forced convection indoors and outdoors. The experimental tests show a clear reduction of the heat exchanger thermal resistance thanks to the radiative coating and consequently, an increase of electric production 8.3 % with outdoor wind velocities of 1 m/s, and up to 54.8 % under free convection conditions. The application of the radiative surface treatment is shown to result in a more stable electrical energy production, suppressing the drastic decrease in the generated electric power that occurs in thermoelectric generators when they work under free convection., The authors acknowledge the support of the Spanish Ministry of Science, Innovation and Universities, and the European Regional Development Fund , under grants PID2021-124014OB-I00 (VIVOTEG), TED2021-129359B-I00 (GEOTEG), PGC2018-101743-B-I00 (SIP) and RTI2018-093921-A-C44 (SMOOTH). Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Continuous electric energy production in Antarctica through geothermal passive thermoelectric generators

  • Astrain Ulibarrena, David
  • Pascual Lezaun, Nerea
  • Catalán Ros, Leyre
  • Araiz Vega, Miguel
  • Alegría Cía, Patricia
  • Rosado, Belén
  • Berrocoso, Manuel
Scientific research in remote areas of Antarctica is often hindered by the challenge of securing a reliable and continuous power supply to operate data collection equipment. Conventional autonomous power systems employed for environmental monitoring encounter significant challenges in this environment: photovoltaic panels prove ineffective owing to the absence of sunlight during the polar winter, while wind turbines necessitate maintenance that cannot be carried out when the site is uninhabited. To overcome these critical limitations, this study demonstrates the viability of a novel solution based on geothermal-powered thermoelectric generation. A passive thermoelectric generator was successfully installed on Deception Island, marking the world's first instance of continuous electrical power generation from geothermal heat in Antarctica. This deployment not only validates the technical feasibility of such systems in harsh environments, but also establishes a promising pathway for reliable, maintenance-free energy supply to support long-term autonomous scientific operations in polar volcanic regions. This groundbreaking system consists of thermoelectric modules and high-efficiency phase change heat exchangers, which operate without moving parts, making them exceptionally robust, reliable, and modular. Field results indicate that the generator using water as the phase change fluid in the cold side heat exchanger produces an average net power of 0.76 W per module, while those using methanol generate 0.59 W. In total, the installation produces an average net power of 4.4 W and an annual electrical energy of 38 kW h. This power system represents an unprecedented advancement in Antarctic research, allowing continuous, year-round study in Deception Island., Spanish State Research Agency and FEDER-UE under the grant PID2021-124014OB-I00. Polar Committee of Spain. Open access funding provided by the Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Experimental analysis of geothermal passive thermoelectric generators combining water and methanol based heat exchangers

  • Pascual Lezaun, Nerea
  • Alegría Cía, Patricia
  • Catalán Ros, Leyre
  • Martínez Echeverri, Álvaro
  • Astrain Ulibarrena, David
Thermoelectric generators are a highly suitable alternative for applications that require robustness, reliability and low maintenance, such as power supply in remote volcanic regions and extreme environments. However, in order to broaden the scope of this technology, it is essential to adapt its design and performance to variable operating conditions. In this context, the present study has developed an innovative system of geothermal passive thermoelectric generators based on a phase change heat exchanger, aimed at the continuous generation of electricity from low-enthalpy geothermal sources, specifically volcanic fumaroles. Experimental tests have evaluated different heat exchanger configurations under a wide range of operating conditions, including different ambient temperatures and wind speeds. The analysis included the power produced, the conversion efficiency and the thermal resistance of the heat exchangers. On the hot side, a heat pipe-based exchanger was compared with a thermosyphon-based exchanger, with the former producing an average of 17% more electricity. To adapt the system to adverse meteorological conditions, both water and methanol were used as working fluids. Water was more efficient, with a 49% lower thermal resistance, resulting in a 17% increase in electricity generation. Nevertheless, when freezing occurs, the performance of the water-based system drops by 90%, while the methanol-based system continues to operate effectively. As a solution, a hybrid system combining water and methanol heat pipes on the cold side has been developed, achieving power outputs of up to 1 W and generating between 600% and 710% more power than the water-based system under freezing conditions., The authors would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE, Spain for funding under the PID2021-124014OB-I00 research project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Resistance-capacitance thermal models as alternatives to finite-element numerical models in the simulation of thermoelectric modules for electric power generation

  • Martínez Echeverri, Álvaro
This paper demonstrates that resistance–capacitance models provide equal results than models based on finiteelement software when predicting the performance of a thermoelectric module under transient-state conditions. Previous papers on this topic fall short as comparing finite-element models with simplified versions of resistance–capacitance models. It was confirmed that resistance–capacitance models replicate results of finite-element models in the simulation of a thermoelectric module under steady-state conditions. Deviations lower than 3 % in electric power and efficiency (ratio of electric power to heat input) are obtained for temperature differences between heat source and heat sink as large as 200 K. Similarly, deviations lower than 3 % are obtained for simulation of a thermoelectric module under transientstate conditions. Resistance-capacitance models not only replicate values, trends and rates of variation predicted by finite-element models under step, linear and sinewave variations in the boundary conditions, but they also do this with negligible computational cost., The authors acknowledge the support of the Spanish Ministry of Science, Innovation and Universities, and the European Regional Development Fund, under grant PID2021-124014OB-I00 (VIVOTEG). Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

400 W facility of geothermal thermoelectric generators from hot dry rocks on the Canary Islands

  • Alegría Cía, Patricia
  • Pascual Lezaun, Nerea
  • Catalán Ros, Leyre
  • Araiz Vega, Miguel
  • Astrain Ulibarrena, David
Geothermal energy has a great potential to be harnessed and requires a boost in technologies to enhance its use. The Canary Islands have a great dependence on fossil fuels, and Lanzarote has important geothermal anomalies currently unexploited due to the absence of water in the soil, what hinders the use of vapour turbines. This work presents the development of the first facility of geothermal thermoelectric generators operating in the world. This novel generators are producing 400 W of power in Timanfaya National Park. It has three geothermal thermoelectric generators, each with 4 thermosyphons per borehole and 40 thermoelectric modules that directly transform heat into electricity. This facility, with the advantages of geothermal energy such as continuity and independence on the weather, requires low maintenance because it does not require moving parts nor water consumption. That makes feasible for the first time to harness the geothermal potential in Lanzarote, producing an electric energy of 9.4 kWh per day, which means 3.42 MWh per year. The field installation of this novel technology has enabled to accurately calculate the Levelized Cost of Energy, which is 0.22 €/kWh. Although a 29% decrease in the power generated by thermoelectric module was detected when installing a GTEG with 40 modules with respect to a GTEG with 10 modules, this decrease is compensated by the fact that by installing more modules, the electrical production per borehole is optimized, reducing the LCOE. The developed facility will avoid the emission of 2.3 tons of CO2 and is totally respectful with the environment if compared to conventional geothermal power plants., We would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE under the grants TED2021-129359B-I00 and PID2021-124014OB-I00 . We would also like to acknowledge the support of the Official School of Industrial Engineers of Navarre with the scholarship Fuentes Dutor. Open access funding provided by the Public University of Navarre .
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Thermoelectric generators for harvesting medium-temperature geothermal anomalies: printed vs bulk devices

  • Khan, Muhammad Irfan
  • Franke, Leonard
  • Rösch, Andres Georg
  • Wang, Zirui
  • Mallick, Mofasser
  • Alegría Cía, Patricia
  • Pascual Lezaun, Nerea
  • Astrain Ulibarrena, David
  • Lemmer, Uli
Recently, thermoelectric generators (TEGs) have gained significant attention for directly converting geothermal energy into electricity. Due to the considerable variations in heat-source and sink geometries and boundary conditions, the design of TEGs should offer flexibility to fulfill the specific constraints. Printing technologies, such as screen printing or 3D printing, offer versatile, cost-effective manufacturing approaches for TEGs, enabling scalability and shape conformability. In this work, we present a comparative performance optimization of both printed TEGs and bulk-material-based TEGs for medium-temperature geothermal anomalies at T ~ 170 ◦ C. The proposed system for geothermal energy harvesting consists of a two-phase thermosyphon serving as the hot-side heat exchanger, TEGs, and an efficient heat sink based on heat pipes. We investigate the performance of both types of TEGs attached to the exterior of the thermosyphon for three heights (h = 100, 200, and 500 mm). For both bulk and printed TEGs, thermal and electrical impedance optimizations are achieved by adjusting the TEG f ill factor, leg dimensions, and the cross-sectional areas of the n-type and p-type legs. Under the given boundary conditions, the higher power density at lower cost occurs at a TEG height of 100 mm for both bulk and printedTEG devices. And in all three cases, at a higher fill factor (F ~ 0.9), printed TEGs showed comparable power densities to bulk TEGs at lower cost. As F decreases, the printed TEGs' power densities drop more rapidly than those of their bulk counterparts. Despite lower performance at lower fill factors, printed TEGs remain promising, with lower cost per watt (€/W) thanks to lower TE material consumption and lower manufacturing cost. Lastly, the projection of the levelized cost of electricity LCOE (€/kWh) and the economic analysis for both approaches conclude our work., The authors acknowledge funding from the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) under Germany's Excellence Strategy for the Excellence Cluster “3D Matter Made to Order” (EXC-2082/2-390761711), the German Federal Ministry for Economic Affairs and Climate Action through WIPANO project 03THWBW004 for financial support. The German Federal Environmental Foundation (Deutsche Bundesstiftung Umwelt - DBU), through the DBU Ph.D. scholarship program, also supported this work. This project has received funding from the European Union's Horizon 2020 Research and Innovation Program under grant agreement no. 814945single bondSolBio-Rev, and we acknowledge funding by the European Research Council, grant 101097876 - ORTHOGONAL. We would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE under the grant PID2021-124014OB-I00.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Field test of a geothermal thermoelectric generator without moving parts on the Hot Dry Rock field of Timanfaya National Park

  • Catalán Ros, Leyre
  • Alegría Cía, Patricia
  • Araiz Vega, Miguel
  • Astrain Ulibarrena, David
Although in the last years thermoelectric generators have arisen as a solution to boost geothermal power generation, tests on field are still scarce. The vast majority of the available studies focus on computational simulations or laboratory experiments, mainly with active heat exchangers that require pumps or fans, and, consequently, present moving parts and auxiliary consumption. The present paper demonstrates for the first time the suitability of a geothermal thermoelectric generator (GTEG) with passive phase change heat exchangers, and therefore, without moving parts nor auxiliary consumption, on the shallow Hot Dry Rock (HDR) field of Timanfaya National Park (Canary Islands, Spain), where 173 °C air anomalies can be found. The device has been in operation without maintenance for 2 years now, producing more than 520 kWh of energy. In terms of power generation, since the installed device is in turn composed of two prototypes with 10 and 6 thermoelectric modules, it has been confirmed that installing more modules leads to a lower generation per module, although total generation can be higher. In fact, the prototype with 10 thermoelectric modules generated a maximum of 20.9 W (2.09 W per module) with a temperature difference between sources of 158 °C, while the prototype with 6 thermoelectric modules obtained 16.67 W (2.78 W per module) under the same conditions. These results open the door for a large-scale exploitation thanks to the intrinsic advantages of modularity, reliability, robustness, and minimal environmental impact of the developed device., The authors would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE under the grants PID2021-124014OB-I00 and TED2021-129359B-I00. Open access funding provided by Universidad Pública de Navarra