Pasar al contenido principal

CONTROL DE CONVERTIDORES ELECTRONICOS DE POTENCIA EN BARCOS DE PROPULSION ELECTRICA

PID2022-136908OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2022
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE VIGO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Carrier phase-shift PWM with minimum stator current-ripple RMS for symmetrical six-phase induction motor drives with nearly sinusoidal winding distribution

  • Medina Sánchez, Martín
  • Gómez Yepes, Alejandro
  • López Sánchez, Óscar
  • Doval Gandoy, Jesús
Symmetrical six-phase (S6) motors offer significant advantages over three-phase ones, for example, fault tolerance and lower per-phase current ratings. Most pulsewidth modulation (PWM) approaches for S6 featuring nearly sinusoidal winding distributions (SWDs) target (ideally) generating sinusoidal voltages in the torque-producing αβ plane with zero-average voltages in the low-impedance x y plane. However, when employing a conventional carrier-based PWM (CBPWM), using a single carrier, substantial stator current ripple (CR) may arise, primarily due to x y switching harmonics. This article demonstrates that these x y harmonics can be significantly suppressed for S6 SWDs by using a phase-shift PWM (PSPWM) technique with two carriers and phase-shift angle θc = π. For any modulation index, θc = π consistently achieves the lowest stator CR (loss), significantly smaller compared with other θc , including the conventional CBPWM. This is shown to be because when PSPWM with θc = π is implemented, the converter switches with just large αβ space vectors (SVs), without x y contributions while avoiding the complexity of SV PWM. Closed-form formulas for switching-harmonic mapping into subspaces are also derived for S6 and any θc , enabling an in-depth understanding of the switching behavior. Additionally, the dc-link CR is analyzed for several θc . Experimental results with a S6 induction motor validate the theory., Xunta de Galicia | Ref. ED431B 2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Super-twisting current regulator for a six-phase induction motor in field weakening conditions

  • Ayala, Magno
  • Doval Gandoy, Jesús
  • Kali, Yassine
  • Rodas, Jorge
  • Gonzalez, Osvaldo
  • Delorme, Larizza
  • Gregor, Raul
This paper addresses the regulation of stator currents in a six-phase asymmetrical induction machine during field-weakening operation, accounting for disturbances and parameter variations. Current control is performed in the d–q, α–β, and x–y reference planes. A novel double-loop current controller based on a discrete-time super-twisting algorithm is proposed to enhance current regulation, particularly under field-weakening conditions where current tracking errors typically deteriorate. This controller ensures precise current tracking with fast error convergence and improved robustness to uncertainties. Experimental results confirm the effectiveness of the controller under both transient and steady-state conditions, including during the field weakening operation., National Council of Science and Technology (CONACYT) | Ref. ESTR01-3, Xunta de Galicia | Ref. ED431B 2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Sequential model predictive torque control for six-phase machines without weighting factors

  • Rodas, Jorge
  • González, Osvaldo
  • Maidana, Paola
  • Medina, Christian
  • Doval Gandoy, Jesús
  • Norambuena, Margarita
  • Ayala, Magno
  • Rodriguez, Jose
Model predictive control has become a powerful and versatile control strategy, particularly effective in controlling multiphase machines. One of its key advantages is the ability to address multiple control objectives by incorporating constraints directly into the cost function. However, this feature typically necessitates the challenging task of tuning weighting factors to balance competing objectives effectively. This paper proposes a sequential model predictive torque control strategy for six-phase induction machines, eliminating the need for weighting factors. The proposed approach simplifies the control design process while maintaining high performance. Simulation and experimental results demonstrate the method’s effectiveness, showing accurate torque, flux tracking, and appropriate stator currents regulation in the α − β and x − y planes. These results highlight the potential of the proposed control strategy for practical implementation in advanced multiphase drive systems., Consejo Nacional de Ciencia y Tecnología (CONACYT) | Ref. PINV01-272, Xunta de Galicia | Ref. GPC-ED431B 2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Agencia Nacional de Investigación y Desarrollo, Chile | Ref. AFB240002, Agencia Nacional de Investigación y Desarrollo, Chile | Ref. 1230250, Agencia Nacional de Investigación y Desarrollo, Chile | Ref. 1241099
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Comprehensive comparative assessment of multiphase overmodulation techniques and three-phase discontinuous PWM methods applied to symmetrical six-phase induction motor drives under overmodulation

  • Medina Sánchez, Martín
  • Gómez Yepes, Alejandro
  • López Sánchez, Óscar
  • Doval Gandoy, Jesús
Among six-phase motors, those featuring symmetrical six-phase motor with a single neutral point (S6N1) offer enhanced fault tolerance. However, a single neutral point lowers the dc-link utilization in the linear pulsewidth modulation (PWM) range. Most previous multiphase overmodulation (OVM) methods address this limitation by injecting just nontorque current-producing harmonics. However, although some OVM methods have been compared regarding current distortion for S6N1, some others have not, and a comparison concerning complexity and inverter and copper loss remains lacking. Moreover, it is unclear if any attain the minimum voltage distortion (MVD), effective in reducing current distortion. Additionally, although three-phase discontinuous PWM (DPWM) approaches have been extended to multiphase drives for the linear PWM region, their behavior in the S6N1 OVM range has not been reported nor compared yet. This article assesses and compares, as its main contribution, the multiphase OVM approaches and three-phase DPWM methods in the S6N1 OVM range concerning voltage and current distortion, inverter and copper loss, and complexity. For comparative purposes, a simple MVD implementation is also devised. Considering the aforesaid figures of merit and certain relevant scenarios, this comparative study establishes the most suitable techniques. The experiments are performed by using an S6N1 induction motor., Agencia Estatal de Investigación | Ref. CNS2022-135773, Xunta de Galicia | Ref. ED431F2020/07, Xunta de Galicia | Ref. ED431B2023/12, Agencia Estatal de Investigación | Ref. RYC2018-024407-I, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Weighting-factor-free sequential predictive torque control using virtual vectors in six-phase IM

  • Maidana, Paola
  • Medina, Christian
  • Doval Gandoy, Jesús
  • Rodas, Jorge
  • Gonzalez, Osvaldo
  • Ayala, Magno
  • Gregor, Raul
Finite-control-set model predictive torque control of multiphase induction machines is often limited by heuristic tuning of weighting factors and inadequate secondary-plane current regulation. To address these limitations, this paper proposes a weighting-factor-free sequential model predictive torque control strategy with virtual voltage vector synthesis (SMPTC-VV) for six-phase induction machine drives supplied by dual two-level voltage source inverters. The proposed scheme employs a sequential optimisation structure that removes weighting factors from the cost function formulation. Virtual voltage vectors are incorporated to suppress non-torque-producing currents in the x − y plane, enabling simultaneous regulation of electromagnetic torque, stator flux, and secondary-plane currents. Experimental validation under steady-state and dynamic conditions, including ±25% magnetising inductance mismatch, demonstrates accurate torque and flux regulation, fast transient response, and improved current quality. The proposed strategy achieves improvements of 10.08% and 53.41% in THDα, and 54.26% and 69.21% in THDa, compared to SMPTC and classical PTC, respectively. In addition, flux regulation is improved by 28.03% and 31.13% relative to SMPTC and classical PTC, respectively, while non-torque-producing x − y currents are improved by 75.40% and 82.58% with respect to SMPTC and classical PTC. The computational effort is limited to 966 floating-point operations per sampling period, corresponding to improvements of 50.66% and 75.66% relative to SMPTC and classical PTC, respectively. The results demonstrate an efficient and experimentally validated predictive torque control solution for high-performance multiphase drives., Universidad Nacional de Asunción, Consejo Nacional de Ciencia y Tecnología (CONACYT), Xunta de Galicia | Ref. ED431B 2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, RIBIERSE-CYTED | Ref. 723RT0150
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

A generalized overmodulation strategy with minimum current distortion for symmetrical and asymmetrical multiphase induction motor drives

  • Medina Sánchez, Martín
  • Gómez Yepes, Alejandro
  • López Sánchez, Óscar
  • Doval Gandoy, Jesús
Multiphase machines are a promising alternative for high-reliability applications. In these applications, overmodulation (OVM) is important since it allows attaining higher modulation indices by injecting, besides zero-sequence voltage harmonics, current-producing ones. In general, the existing techniques are able to limit to some extent the current total harmonic distortion (THD). However, most do not ensure the minimum current THD, thereby not guaranteeing the minimum harmonic stator copper loss. Furthermore, most are intended just for particular phase numbers n , symmetrical/asymmetrical winding arrangements and neutral-point (NP) configurations. OVM with low THD remains unaddressed in most types of multiphase motors. This article overcomes these limitations by proposing a generalized OVM strategy that attains the minimum current THD in induction motors with any n , winding arrangement, and NP configurations. Two techniques are outlined. One of them injects only non-torque-related harmonics, while the other technique exploits torque-producing harmonics to further reduce the current THD and to attain modulation indices up to square waveform. The superiority of the proposal in terms of current THD is substantiated through studies for multiple kinds of multiphase machines. The experiments are performed by using two six-phase induction motors with symmetrical/asymmetrical windings when 1 and 2 NPs are set., Xunta de Galicia | Ref. ED431F2020/07, Xunta de Galicia | Ref. ED431B2023/12, Agencia Estatal de Investigación | Ref. RYC2018-024407-I, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Grid-forming converter with enhanced current limiting dynamics during grid faults and wide stability range

  • Ríos Castro, Diego
  • Fernández Abraldes, Pablo Marino
  • Pérez Estévez, Diego
  • Doval Gandoy, Jesús
Grid-forming (GFM) converters facilitate voltage and frequency stability in grids with high penetration of inverter-based renewable energy technologies. Under nominal conditions, the primary function of GFM converters is to control the output voltage by operating in voltage-source mode (VSM). During off-nominal conditions, especially in the presence of severe grid disturbances, the primary objective is to ensure accurate and fast-response current limiting to protect the GFM converter from overcurrents by operating in current-source mode (CSM). A wide stability margin of the inner loops must be guaranteed in nominal and contingency conditions due to the high variability of scenarios that a GFM converter may encounter. This article proposes a double-loop controller with current-limiting capability for GFM converters, ensuring good GFM performance in stand-alone and grid-connected scenarios, including those with very weak and stiff grids. Additionally, the proposed controller provides an enhanced current-limiting response with precise current control during faults. Finally, the proposed controller demonstrates a wide stability range in both VSM and CSM modes. This is experimentally validated through tests of GFM performance in very weak and stiff grids, with sudden changes in the short-circuit ratio, as well as through current-limiting tests under grid-voltage bolted faults conducted across different grid-impedance conditions., Xunta de Galicia | Ref. ED481B 2023/019, Xunta de Galicia | Ref. ED431B 2023/12, Ministerio de Educación y Universidades | Ref. FPU22/02102, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Sensitivity-based impedance modeling of AC voltage-controlled converters

  • Pérez Estévez, Diego
  • Ríos Castro, Diego
  • Doval Gandoy, Jesús
Loads affect the stability of grid-forming (GFM) converters, both in stand-alone and grid-connected modes. This has motivated the development of methods that study the stability of GFM converters using an impedance-based analysis. AC impedance-based stability analyses usually study the stability of GFM converters by applying the Nyquist criterion to an impedance ratio denoted as minor loop gain. A limitation of the previous approach when applied to GFM converters, which is not always clearly stated, is that the output impedance of a GFM converter depends on the impedance seen by the converter. This loading effect is not accurately modeled in the literature. This article proposes an impedance model that accounts for this loading effect on the GFM converter output impedance, without introducing approximations. As a direct consequence of the presented impedance model, the stability of the GFM converter when connected to different loads can be determined by checking the stability of a single transfer function, the sensitivity function. Using the sensitivity function, the impedance model presented also reveals a clear link between the voltage controller characteristics and the converter output impedance, which has been reported as a limitation of prior impedance-based analysis methods., Xunta de Galicia | Ref. ED431B 2023/12, Xunta de Galicia | Ref. ED481B-2023-019, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Novel single-loop control strategy for 400 Hz voltage source inverter with LC filter

  • Mohebi , Mahdi
  • Fernández Abraldes, Pablo Marino
  • Pérez Estévez, Diego
  • Doval Gandoy, Jesús
The control of 400 Hz Ground Power Units (GPUs) in the range of several hundreds of kW poses distinct challenges, as the switching frequency (fsw) must be constrained to limit switching losses. This constraint typically results in low ratios of the switching and LC filter natural frequencies (fn) relative to the fundamental frequency. Notably, without mitigation, such systems often face stability issues or non-minimum phase behavior when fn<fs/3 (where fs is the sampling frequency). To address these challenges, this paper introduces a single-loop voltage control strategy for a 400 Hz voltage-source inverter (VSI) featuring a robust voltage decoupling scheme. Crucially, this decoupling allows the system to maintain minimum phase characteristics and operate with positive gains even when fn<fs/3, effectively solving the stability problems inherent to this operating region. The proposed architecture employs a proportional-resonant (PR) controller, with parameters systematically tuned to achieve maximum system damping based on stability regions dependent on the ratio between the sampling and natural frequencies. Validated through simulation and experimental procedures, the proposed method demonstrates precise voltage tracking and a robust dynamic response, proving its suitability for high-power, high-fundamental-frequency applications., Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Xunta de Galicia | Ref. ED431B 2023/12, Ministerio de Educación y Universidades | Ref. FPU22/02102
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Per-phase stator-resistance estimation by DC-signal injection in open-phase fault-tolerant six-phase induction motor drives

  • Gómez Yepes, Alejandro
  • Abdel-Majeed, Mahmoud Said
  • Abdel-Azim, Wessam E.
  • Abdel-Moneim, Mohamed G.
  • Abdel-Khalik, Ayman Samy
  • Ahmed, Shehab
  • Doval Gandoy, Jesús
Multiphase machine drives are advantageous over three-phase ones in features such as tolerance to open-phase faults (OPFs). Six-phase (6P) ones offer an excellent compromise between complexity and fault tolerance. In particular, those with a symmetrical arrangement of the stator phase windings and a single neutral point provide superior postfault capability. To ensure high reliability and performance, the stator resistance should be monitored. This can be attained with good robustness to uncertainties by dc-signal injection. This article proposes a dc-based resistance estimation method for symmetrical 6P induction machines that achieves the following main characteristics simultaneously for the first time: estimation of individual stator phase resistances and suitability for either healthy or OPF conditions. The dc injection is performed so that no torque ripple is produced and so that the increase in loss, peak current, and braking torque is relatively small. The method is designed so that it is robust to the deviation in the stator neutral-point voltage due to resistance asymmetry. Experimental results are provided., Agencia Estatal de Investigación | Ref. CNS2022-135773, Xunta de Galicia | Ref. ED431F2020/07, Xunta de Galicia | Ref. ED431B2023/12, Agencia Estatal de Investigación | Ref. RYC2018-024407-I, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Grid-connected converter with grid-forming and grid-following modes presenting symmetrical and asymmetrical fault ride-throug capability

  • Ríos Castro, Diego
  • Pérez Estévez, Diego
  • Doval Gandoy, Jesús
Grid-connected converters must remain coupled to the grid during a fault. They have to control the reactive currents injected to the grid because of its limited overload capacity. In particular, grid-forming (GFM) converters ride through the fault either preserving GFM operation or switching from GFM to grid-following (GFL) mode. In the GFM mode, the current cannot be controlled, and therefore, mechanisms as virtual impedances become necessary. This article proposes a converter with GFM and GFL capabilities that demonstrates effective voltage tracking in the GFM mode and current tracking in the GFL mode, good dynamic disturbance rejection response, and wide stability range and robustness in both modes. During a fault, the proposed converter switches from GFM to GFL mode in order to precisely control the injected currents. The current control is able to limit the current at the inception of severe faults. This characteristic is preserved for a wide range of grid impedances, thanks to its good robustness and wide stability margin. As a result, the controller can operate in a stand-alone mode, connected to a weak grid or connected to a stiff grid with a short-circuit ratio of up to 50. The fault ride-through capability of the converter is tested under severe symmetrical and asymmetrical faults., Xunta de Galicia | Ref. ED431B2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Improving steady state accuracy in field-weakened six-phase induction machines with integrator and modulated predictive control

  • Ayala, Magno
  • Doval Gandoy, Jesús
  • Rodas, Jorge
  • Gonzalez, Osvaldo
  • Gregor, Raúl
  • Delorme, Larizza
  • Romero, Carlos
  • Fleitas, Ariel
Finite-control-set model predictive control techniques are considered an exciting option for high-performance control multiphase drives due to their fast dynamic response, ability to handle multiple targets and constraints, and adaptability to different power converters or machine models. However, these techniques have some drawbacks, such as poor current reduction (x−y) and steady-state error (d−q), especially in the field weakening zone. Although some proposals have addressed these issues by adding modulation stages or designing new cost functions, there is still room for improvement, especially in steady-state error reduction. Therefore, this article proposes to include an integrator attached to a modulated predictive current controller applied to a six-phase induction machine to improve its performance throughout the entire speed range regarding steady-state error mitigation. Experimental tests were carried out to validate the effectiveness of the proposed controller. Tests were carried out evaluating the reduction of the steady-state error (d−q), the current tracking, the (x−y) currents reduction and the total harmonic distortion., Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Xunta de Galicia | Ref. GPC-ED431B 2023/12
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Virtual-vector-based predictive torque control for six-phase IM with reduced computational burden and copper losses

  • González, Osvaldo
  • Doval Gandoy, Jesús
  • Ayala, Magno
  • Rodas, Jorge
  • Maidana, Paola
  • Medina, Christian
  • Romero, Carlos
  • Delorme, Larizza
  • Gregor, Raul
  • Maciel, Ricardo
Finite-control-set model predictive control (FCS-MPC) has become widely accepted in multiphase drives due to its adaptability and robust dynamic response. However, multiphase machines, characterized by low secondary plane (x−y) impedance, which is absent in their three-phase counterparts, often exhibit poor current quality under conventional FCS-MPC strategies. This paper proposes a novel predictive torque control (PTC) scheme based on virtual vectors to improve (x−y) current regulation by ensuring zero average (x−y) voltage generation. The proposed method is compared with classic PTC, which cannot achieve proper (x−y) current regulation because it uses a single switching state during the sampling period. Experimental validation includes a detailed comparison of torque and flux behavior, (x−y) current mean square error, and total harmonic distortion of the fundamental stator currents, demonstrating the effectiveness of the proposed control approach under various operating conditions. Experimental results confirm reductions of approximately 79.7% in computational burden and 98.4% in copper losses when using PTC-VV compared to classic PTC. An asymmetrical six-phase induction machine is used as the case study., Consejo Nacional de Ciencia y Tecnología (CONACYT) | Ref. PINV01-272, Consejo Nacional de Ciencia y Tecnología (CONACYT) | Ref. INIC01-35, Xunta de Galicia | Ref. GPC-ED431B 2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Programa Iberoamericano de Ciencia y Tecnología para el Desarrollo | Ref. 723RT0150
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Identification of magnetization inductance for six-phase induction machines driven by modulated predictive control in field weakening zone

  • Ayala, Magno
  • Doval Gandoy, Jesús
  • Rodas, Jorge
  • Gonzalez, Osvaldo
  • Delorme, Larizza
  • Maidana, Paola
  • Medina, Christian
  • Gregor, Raúl
Finite-control-set model predictive control (FCS-MPC) has achieved superiority in managing multiphase induction machines due to its quick dynamic response, control flexibility, and overall good performance. Its advantages, including simplicity, computational efficiency, compensation for system perturbations, and effective handling of multivariable problems, have made it a competitive alternative in various industrial applications. Nevertheless, FCS-MPC has some limitations. It is highly dependent on the accuracy of the predictive model’s parameters. Unfortunately, the estimation of magnetizing inductance, the most critical factor, especially in the weakening field region, has not been studied yet. Focusing on this gap, this article proposes a technique to estimate the magnetizing inductance in the field weakening zone for a six-phase asymmetrical induction machine driven by the FCS-MPC. Experimental tests have verified the effectiveness of the proposed method, considering stator currents and rotor speed tracking, as well as a reduction in the (x − y) currents., Xunta de Galicia | Ref. ED431B 2023/12,, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Hysteresis current control for six-phase induction motor drives with reduced ripple and improved tracking based on subspace decomposition and restrained voltage vectors

  • Shawier, Abdullah
  • Abdel-Azim, Wessam E.
  • Gómez Yepes, Alejandro
  • Abdel-Khalik, Ayman Samy
  • Hamad, Mostafa S.
  • Ahmed, Shehab
  • Doval Gandoy, Jesús
Six-phase induction motor (6PIM) drives offer enhanced fault tolerance and reduced per-phase ratings. Hysteresis current control (HCC) is attractive for 6PIMs because it is simple, robust and fast. HCC is conventionally implemented so that each leg voltage is directly set based on the respective phase-current error. However, this approach does not consider that, in multiphase drives, phase voltages and currents are related through a combination of equivalent impedances corresponding to various subspaces. In general, there is a notable dissimilarity between these impedances, being typically small for secondary ( xyxy ) subspaces. This can cause large current distortion and poor reference tracking. This article proposes an improved HCC for 6PIM drives. Instead of directly inputting the per-phase current error to the hysteresis comparator and directly applying the switching states chosen by it, the input and output components associated with different subspaces are segregated. The input and output xyxy components are nullified in open loop so that the xyxy impedance no longer affects the HCC behavior, even if low. This prevents the disrupting xyxy currents, ensures effective tracking of the torque/flux-producing αβαβ reference current, and enables reconfiguration-less fault tolerance. Experiments using 6PIMs with different winding configurations corroborate the significant advantages of the proposal., Xunta de Galicia | Ref. ED431F2020/07, Xunta de Galicia | Ref. ED431B2020/03, Agencia Estatal de Investigación | Ref. RYC2018-024407-I, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

A carrier-based overmodulation strategy with minimum voltage distortion for symmetrical n-phase induction motor drives

  • Medina Sánchez, Martín
  • Gómez Yepes, Alejandro
  • López Sánchez, Óscar
  • Abdel-Khalik, Ayman Samy
  • Doval Gandoy, Jesús
Multiphase machines have significant benefits over their three-phase counterparts. One of them is the possibility of further exploiting the dc-link voltage by injecting non-torquerelated voltage harmonics in the xy planes. This allows reaching higher modulation indices in the overmodulation (OVM) region of pulsewidth modulation (PWM) while avoiding torque ripple in motors with negligible space harmonic effects. The most prominent OVM techniques are those based on the instantaneous minimization of the xy voltage. These methods were devised just for five-phase drives and have the drawback that they lack generality. This article overcomes this limitation by proposing an OVM strategy for symmetrical induction motor drives with any odd phase number n. The proposal achieves the minimum voltage distortion, and consequently, it greatly mitigates the xy current distortion. Indeed, it attains the lowest current distortion compared with the existing techniques. It relies on carrier-based PWM in its design and implementation stages, and accordingly, it is much simpler than previous methods. Furthermore, the inverter switching frequency (loss) is substantially reduced. Theoretical assessments are given for drives with odd n between 5 and 11. The experiments are performed with a symmetrical nine-phase induction motor with a single neutral point, Agencia Estatal de Investigación | Ref. RYC2018-024407-I, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Xunta de Galicia | Ref. ED431F 2020/07, Xunta de Galicia | Ref. GPC-ED431B 2020/03
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Field-weakening strategy with modulated predictive current control applied to six-phase induction machines

  • Ayala, Magno
  • Doval Gandoy, Jesús
  • Rodas, Jorge
  • Gonzalez, Osvaldo
  • Gregor, Raúl
  • Delorme, Larizza
  • Romero, Carlos
  • Fleitas, Ariel
The predictive current controller has arisen as a practicable technique for operating multiphase machines due to its fast dynamic response, control flexibility, and overall good performance. However, this type of controller has limitations, e.g., it tends to suffer from steady-state tracking errors in (d−q) currents; high computational burden; and high (x−y) currents, which become more pronounced at higher speeds, thereby worsening its sustainability. While some proposals have addressed these limitations by incorporating modulation stages and new cost functions, there is still room for improvement, particularly at higher speeds. In line with the pursuit of sustainable advancements, this article explores the integration of a field-weakening strategy with a modulated predictive current controller applied to a six-phase induction machine to improve its performance at current tracking for higher speed ranges. Experimental tests were conducted to validate the effectiveness of the proposed controller, assessing stator current tracking, reduction in the (x−y) currents, and the total harmonic distortion., Xunta de Galicia | Ref. GPC-ED431B 2023/12, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

New stability region for the single-loop AC-voltage control in LC-filtered VSIs and its improvement by means of voltage decoupling

  • Fernández-Abraldes, Pablo Marino
  • Ríos Castro, Diego
  • Pérez Estévez, Diego
  • Doval Gandoy, Jesús
Voltage-controlled voltage-source inverters with an output LC-filter are used in a wide variety of power supply applications. LC-filters allow for the attenuation of switching harmonic content, but their resonance can compromise the stability of the system. One of the most common control techniques in these systems consists of a single-loop voltage control with proportional-resonant (PR) or resonant (R) controllers. Numerous previous publications have shown that these systems are only stable for certain ratios between the resonant frequency of the filter (fn) and the sampling frequency (fs), leading to the proposal of different methods to widen this stability region. However, existing methods are based on a continuous-time domain stability analysis, where some approximations are used. This article, after presenting a discrete-time domain stability analysis without approximations that results in a stability region different from that presented in previous publications, demonstrates that the single-loop voltage control with PR controller and capacitor voltage unitary decoupling allows working with positive proportional gains when fn is either above or below fs/3, improving the performance of existing methods. The article also demonstrates that unitary decoupling of the capacitor voltage is not as effective with an R controller. Experimental tests confirm the theoretical analysis conducted., Xunta de Galicia | Ref. ED481B-2023-019, Xunta de Galicia | Ref. ED431B 2023/12, Ministerio de Universidades | Ref. FPU22/02102, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Complete stability region of the double-loop AC-voltage control in LC-filtered VSIs and its improvement by means of voltage decoupling

  • Fernández Abraldes, Pablo Marino
  • Ríos Castro, Diego
  • Pérez Estévez, Diego
  • Doval Gandoy, Jesús
Voltage-controlled voltage-source inverters with an output LC filter are used in a wide variety of power supply applications. Common control structures include single-loop and double-loop voltage control, typically employing a proportional-resonant voltage controller. This article focuses on the double-loop voltage control, where a proportional controller is employed in the inner current control loop. The stability region is defined as the frequency ratios between the sampling frequency (fs) and the natural frequency of the LC filter (fn) with which the system can be stable. In previous publications, it has been proposed to place the current controller in the feedback path of the inner control loop, rather than in the forward path, with the aim of increasing the stability region. This article demonstrates that both control structures are equivalent, with the same stability region, although they require different controller tuning. This article presents, for the first time, the complete stability region of the double-loop voltage control, and demonstrates that it can be stable for any frequency ratio fn/fs. The stability region presented in previous publications, where fn=fs/6 is a critical frequency, is the stability region that allows obtaining a minimum-phase system, which should not be confused with the complete stability region. Finally, it is demonstrated that the unitary decoupling of the capacitor voltage allows obtaining a minimum-phase system across the complete stability region. Experimental results confirm the theoretical analysis conducted., Xunta de Galicia | Ref. ED481B 2023/019, Xunta de Galicia | Ref. ED431B 2023/12, Ministerio de Educación y Universidades | Ref. FPU22/02102, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Asymmetric impedance model for grid-forming converters with droop control

  • Pérez Estévez, Diego
  • Ríos Castro, Diego
  • Fernández Abraldes, Pablo Marino
  • Monteiro, Vitor
  • Pinto, J. G.
  • Afonso, João L.
  • Doval Gandoy, Jesús
This article introduces an impedance model for a grid-forming (GFM) converter with droop control (Droop-GFM converter) connected to a weak power grid. The proposed model offers a more accurate and simpler alternative to the conventional minor-loop criterion and the generalized Nyquist stability criterion for studying the stability of a Droop-GFM converter, as it accounts for loading effects and uses only two transfer functions. Formulated in the αβ frame, the model consists of only two balanced impedances, offering a clearer physical interpretation of the impedance asymmetry introduced by droop control, in contrast to dq-frame impedance matrix models. The model describes frequency coupling effects (the mirror frequency problem) across the entire frequency range, providing both a geometric and physical understanding of this phenomenon. It allows determination of the bandwidth of the frequency coupling region, and how this region changes based on the droop coefficients and the loading condition of the Droop-GFM converter. The theoretical findings are validated experimentally using a Droop-GFM converter in three distinct scenarios, including: weak power grid operation, a change in the droop coefficients, and a change in the power grid impedance., Xunta de Galicia | Ref. ED481B 2023/019, Xunta de Galicia | Ref. ED431B 2023/12, Ministerio de Educación y Universidades | Ref. FPU22/02102, Agencia Estatal de Investigación | Ref. PID2022-136908OB-I00, Universidade de Vigo/CISUG