Pasar al contenido principal

DISEÑO E IMPRESION 3D DE IMPLANTES BIFASICOS POROSOS PERSONALIZADOS PARA EL TRATAMIENTO DE DEFECTOS OSTEOCONDRALES

PID2022-137911OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2022
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SEVILLA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetron sputtered ß-Ti coatings for biomedical application: A HiPIMS approach to improve corrosion resistance and mechanical behavior

  • Sánchez López, Juan Carlos
  • Godinho, Vanda
  • López-Santos, Carmen
  • Navarro, Paula
  • Rodríguez Albelo, Luisa Marleny
  • Sánchez Pérez, Miriam
  • Jiménez Piqué, Emilio
  • Torres, Yadir
This work presents the surface modification of commercially pure Ti specimens (c.p.-Ti) prepared by conventional powder metallurgy by depositing a thin film of a ß-Ti alloy (Ti-35Nb-7Zr-5Ta, wt. %, TNZT). Two types of pulsed technologies: conventional (p-DC) and high-power impulse magnetron sputtering (HiPIMS), with and without bias assistance (−60 V) under similar power conditions (250 W) were applied on titanium specimens and silicon substrates leading to different film morphologies and functional properties. Microstructural, X-ray diffraction, nanoindentation, surface wetting, XPS and electrochemical impedance measurements were done to characterize their functionality. All the coatings presented a reduced Young's Modulus (E ≤ 80GPa) compared to the bulk Ti, representing a reduction of more than 30 %. This decrease can significantly contribute to the reduction of the stress-shielding effect, mitigating the risk of implant loosening and failure. The hardness values of TNZT coatings, slightly lower than c.p.-Ti substrate, range from 4.1 to 4.7 GPa. XPS analysis shows a passivation layer of TiO2, Nb2O5, and ZrO2, which offers high impedance and excellent corrosion resistance. The best compromise between mechanical and corrosion properties is achieved with the HiPIMS technology, thanks to its compact film microstructure with high electrical resistance, despite its limited thickness of about 1 μm., This research is part of the R + D + i projects PDC2022-133369-I00 and PID2022-137911OB-I00, both funded by MCIN/AEI/10.13039/501100011033. The scientific-technical services at the Instituto de Ciencia de Materiales de Sevilla are also acknowledged. C.L.-S. thanks the support of the University of Seville through the VI PPIT-US and the Ramon y Cajal Spanish National programs funded by MCIN/AEI/ 10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrical impedance characterization and modelling of Ti-Β implants

  • Navarro, Paula
  • Barrera, Miguel
  • Olmo, Alberto
  • Torres, Yadir
Commercially pure titanium (c.p. Ti) and Ti6Al4V alloys are the most widely used metallic biomaterials in the biomedical sector. However, their high rigidity and the controversial toxicity of their alloying elements often compromise their clinical success. The use of porous β-Titanium alloys is proposed as a solution to these issues. In this regard, it is necessary to implement economic, repetitive, and non-destructive measurement techniques that allow for the semi-quantitative evaluation of the chemical nature of the implant, its microstructural characteristics, and/or surface changes. This study proposes the use of simple measurement protocols based on electrical impedance measurements, correlating them with the porosity inherent to processing conditions (pressure and temperature), as well as the chemical composition of the implant. Results revealed a clear direct relationship between porosity and electrical impedance. The percentage and/or size of the porosity decrease with an increase in compaction pressure and temperature. Moreover, there is a notable influence of the frequency used in the measurements obtained. Additionally, the sensitivity of this measurement technique has enabled the evaluation of differences in chemical composition and the detection of intermetallics in the implants. For the first time in the literature, this research establishes relationships between stiffness and electrical impedance, using approximations and models for the observed trends. All the results obtained corroborate the appropriateness of the technique to achieve the real-time characterization of Titanium implants, in an efficient and non-invasive way., This work was supported by the Ministry of Science, Innovation and Universities of Spain under the grant of the R + D + i project PID2022–137911OB-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biodegradable polyacrylamide-based hydrogels with unique bactericidal and osteoinductive properties to improve the clinical success of porous titanium implants

  • Martínez, Guillermo
  • Castellano-Pozo, Maikel
  • Merinero de los Santos, Manuel
  • Casado-Jurado, David
  • Huertas Sánchez, Pablo
  • Pajuelo, Eloísa
  • De-Miguel, Manuel
  • Begines, Belén
  • Torres, Yadir
  • Alcudia, Ana
Stress-shielding phenomenon, infections, and limited bone integration are traditional drawbacks associated with titanium implants. Biodegradable polyacrylamide-based hydrogels synthesized with an 8-fold scaled up, disulfide bond-containing crosslinker, were prepared to overcome these limitations. Hydrogels' biodegradability in the presence of glutathione has been demonstrated. Additionally, hydrogels exhibited strong antibacterial activity against pathogens such as P. aeruginosa and S. aureus, along with promising osseointegrative properties, in vitro fibroblast (CCL-1) viability, and in vivo biocompatibility in C. elegans. Porous titanium (Ti) fabricated via space-holder technique were infiltrated with previously described hydrogels. The optimal system, featuring a 4 wt% crosslinked acrylamide-based hydrogel infiltrated into 60 vol%, 355–500 μm Ti substrate, showed excellent biomechanical integrity and biofunctionality, supporting its potential as a safe and effective bone implant. Additionally, the study introduces streamlined, cost-effective methodologies for implant testing and characterization., This research was funded by Ministerio de Ciencia, Innovación y Universidades, Grant Numbers, PID2022-137911OB-I00 and PID2022-136791NB-I00. Escherichia coli expressing GFP and Pseudomonas putida expressing mScarlet, respectively, and Eduardo Villalobo for his assistance with the manipulation of these two bacterial strains. The authors also thank Biblioteca and Servicios Generales from Universidad de Sevilla and especially Servicio de RMN for facilities, and and VII Plan Propio de Investigación y Transferencia-US 2022 for Grant Numbers 2022/00000332 and 2022/00000277. G.M.M. thanks VII Plan Propio de Investigación from University of Seville for predoctoral Grant, M.C.P. thanks to Marie Sklodowska-Curie Actions for MSCA IF grant coDNAres 101023902, and D.C. thanks Ministerio de Educación y Formación Profesional for a grant ``Beca de Colaboración de Estudiantes en Departamentos Universitarios´´., Peer reviewed