Pasar al contenido principal

ESTUDIO DE LA INTEGRACION OPTIMIZADA DE SISTEMAS DE POST-TRATAMIENTO PARA LA REDUCCION DE NOX Y EMISIONES SECUNDARIAS EN MOTORES DE HIDROGENO

PID2023-146449OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2023
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparative Analysis of Pre- and Post-Catalyst Exhaust Gas Recirculation Systems for Turbocharged Spark-Ignition Engines

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Pitarch, Rafael
[EN] Low-pressure exhaust gas recirculation (LP-EGR) systems are widely used in current sparkignition engines due to benefits in knock control, heat transfer losses, and pumping work. Usually, the gases are extracted downstream of the aftertreatment system (ATS). Consequently, an intake throttle valve or an exhaust backpressure valve is required to ensure recirculation at low speeds and loads, increasing the pumping losses. The current work explores the potential of an alternative architecture where the exhaust gases are extracted before the aftertreatment system to reduce such losses and increase fuel efficiency. For this purpose, a fully instrumented 1.3 L turbocharged direct-injection spark-ignition engine with variable valve timing (VVT) and a Euro 6d aftertreatment module is employed. Both pre- and post-aftertreatment extraction architectures are implemented, using the same LP-EGR cooler and overall length to minimize the variations induced by the pressure drop of the LP-EGR line itself. The results show that at low and intermediate speeds and loads, the exhaust gas extraction before the aftertreatment does provide around 2% lower fuel consumption for most of the operating conditions, thanks to the expected benefits in pumping work. However, as the speed and load increase, combined deteriorations in the compressor inlet temperature and the combustion performance for the precatalyst layout shorten the fuel consumption benefit, making both layouts equivalent., MCIN/AEI/10.13039/501100011033/FEDER, UE (Grant No. PID2023-146449OB-I00; Funder ID: 10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of hydrogen combustion exhaust conditions on NO removal and N2O formation over Pt/Pd oxidation catalysts

  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Conde-Cortabitarte, Carla|||0009-0007-8337-3935
[EN] As the automotive industry shifts to lower carbon emissions, hydrogen (H 2 ) is emerging as a promising carbon-free fuel for internal combustion engines (ICEs). However, burning H 2 still produces pollutants that pose environmental and health risks, mainly nitrogen oxides (NO x ). These pollutants, along with unburned H 2 , which acts as a greenhouse gas precursor, must be abated by exhaust gas aftertreatment systems (ATS). Oxidation catalysts (OCs) can be used to reduce unburned H 2 emissions in lean-burn ICEs, but also have an impact on the NO 2 /NO x ratio. Due to the changes in exhaust gas composition from H 2 -ICEs, it is essential to evaluate how the reactivity of OCs is affected since it will condition the response of the remaining ATS devices. This study evaluates the performance of a Euro 6 d Pt/Pd OC under exhaust gas conditions representative of H 2 -ICEs. The reaction pathways of NO were analyzed with varying O 2 and H 2 O levels, as well as significant unburned H 2 . The presence of H 2 promoted low-temperature NO x reduction but also resulted in significant nitrous oxide (N 2 O) emissions. Additionally, the high water concentration inhibited the NO conversion but increased the N 2 O yield, while H 2 oxidation involved a thermal effect shifting the catalyst response toward lower exhaust temperatures., This research has been supported by Grant PID2023-146449OB-I00 funded by MCIN/AEI/10.13039/501100011033/FEDER, UE and program PAID-06-23 funded by the Universitat Politecnica de Valencia. Additionally, C. Conde thanks PhD funding from Universitat Politecnica de Valencia through grant FPI-2022-S2-49099, which is supported by project CIPROM/2021/061 funded by Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Role of H2in CO and HC conversion by automotive oxidation catalysts underreal-world driving conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Conde-Cortabitarte, Carla|||0009-0007-8337-3935
  • Martin Herreros, Jose
  • Tsolakis, Athanasios
[EN] As hydrogen (H2) gains attention as a clean alternative to conventional fuels, understanding its effect on engine processes becomes necessary. This is especially challenging in dual-fuel applications combining H2 and carbon- based fuels so that flexibility in combustion can be extended to emissions control. In this study, the real-driving conversion efficiency of CO and HC in Pt and Pt/Pd oxidation catalysts is investigated in the presence of H2 applying an experimental-computational approach. The analysis of the experimental data drives to propose a reaction mechanism that accounts for alternative pathways for CO and HC oxidation when H2 is present. This mechanism is then implemented in a one-dimensional model for dual-layer washcoat honeycomb catalytic converters. Firstly, the model is calibrated against experimental temperature-ramp tests to assess the sensitivity of CO and HC light-off temperature and selectivity to O2 and H2 depending on the catalytic formulation. Then, the H2 effects on the conversion efficiency are analysed under real driving conditions considering a wide range of H2 content. Finally, the changes in the catalyst response and the differences between Pt and Pt/Pd samples as a function of a variety of simple post-injection strategies are discussed in terms of cumulative conversion efficiency benefits against H2 consumption., This research has been supported by Grant PID2023-146449OB-I00 funded by MCIN/AEI/10.13039/501100011033/FEDER, UE. Additionally, E.J. Sanchis thanks the support to the internship at University of Birmingham from Conselleria de Innovacion, Universidades, Ciencia y Sociedad Digital of Generalitat Valenciana through grant CIBEST/2021/12; C. Conde thanks PhD funding from Universitat Politecnica de Valencia, Spain through grant FPI-2022-S2-49099, which is supported by project CIPROM/2021/061 funded by Generalitat Valenciana, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of two-stage advanced turbocharging systems for medium duty hydrogen engine conversion: A comprehensive 1D engine modelling approach

  • Serrano, J.R.|||0000-0003-0692-3917
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Gómez-Vilanova, Alejandro|||0000-0002-6627-7075
  • González-Domínguez, David
[EN] This paper explores the potential of retrofitting traditional fuel engines to hydrogen operation, leveraging their advantage for greenhouse gas emission reduction. Specifically, the work focuses on a 3-litre diesel automotive application engine equipped with a two-stage turbocharging system. Such architecture is particularly interesting for hydrogen applications since it can potentially maintain the lean mixtures typically used on hydrogen engines with a reduced deterioration in performance. First, an extensive experimental campaign on the original diesel engine is used to develop and validate a comprehensive one-dimensional engine model. Subsequently, the developed model is adapted from the computational point of view to evaluate hydrogen operation, including combustion profiles extrapolated from existing literature combined with a predictive sub-model to evaluate knocking limitations as a function of the boost pressure level. Then, the turbocharging system management is optimised under different assumptions. Afterwards, the full-load performance is compared for direct and indirect injection and different dilution levels. According to the simulation results, the hydrogen engine can achieve over 80% of the original diesel engine's torque output, successfully meeting the target boost pressure, thanks to the versatility of the dual-stage turbo- charging system. This research advances hydrogen engine conversion technology, paving the way for cleaner and more efficient transportation systems., This publication is a part of project PID2023-146449OB-I00, funded by MCIU, Spain (MCIU/AEI/10.13039/501100011033) and the European Regional Development Fund (ERDF/EU) . This research has been partially supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana, Spain. Finally, the experimental campaign and engine model validation activities related with the diesel engine have been funded by the mobility scholarship assigned to Alejandro Gomez-Vilanova during his phD preriod, with code FPU18/04811 corresponding to Formacion de Profesorado Universitario (FPU) by Ministerio de Universidades, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Understanding the generation characteristics of NH3 and N2O in three-way catalysts for stoichiometric LPG engines

  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Garcia Afonso, Oscar
[EN] This work investigates the formation of ammonia (NH3) and nitrous oxide (N2O) over a commercial three-way catalyst (TWC) in a stoichiometric LPG engine. A detailed reactor model was developed and validated against light-off tests at three air-to-fuel ratios (lambda = 0.975, 0.995, 1.0) on a synthetic gas bench, which span a wide temperature range and represent the full stoichiometric-to-rich operating window conducive to secondary-pollutant formation. The model reproduces in these tests the NO, CO, and hydrocarbon conversion, as well as NH3 and N2O formation. NH3 is produced mainly in the front section of the catalyst between 300-450 degrees C under rich mixtures and depends on in situ H-2 generation. N2O formation, dominated by NO-CO reactions, is promoted near stoichiometry but inhibited when CO is abundant in the washcoat. Sensitivity analyses were conducted to assess the effect of space velocity (SV), hydrocarbon speciation, and H-2 addition. Lower SV and higher propane content enhance NH3 by increasing H-2 generation without shifting its temperature window. Direct H-2 addition moves NH3 onset to 150 degrees C, confirming that H-2 availability limits NH3 formation. For N2O, reducing SV shifts formation to lower temperatures - by >50 degrees C - through CO consumption, whereas hydrocarbon speciation and H-2 addition scarcely affect it., This research has been supported by Grant PID2023-146449OB-I00 funded by MCIN/AEI/10.13039/501100011033/FEDER, UE and program PAID-06-23 funded by the Universitat Politecnica de Valencia, Spain.