Pasar al contenido principal

DESARROLLO DE SENSORES PARA COMPUESTOS ORGANICOS VOLATILES INTEGRADOS EN SISTEMAS DE MEDIDA DE CALIDAD DE AIRE

PID2023-151565OB-C42

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2023
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Room-Temperature Environmental Gas Detection: Performance Comparison of Nanoparticle-Based Sensors Fabricated by Electrospray, Drop-Casting, and Dry Printing Based on Spark Ablation

  • Sánchez-Vicente, Carlos
  • Santos, José Pedro
  • Sayago, Isabel
  • Mazzola, Vincent
  • Sacco, Leandro
Chemical nanosensors based on tin dioxide (SnO2) and zinc oxide (ZnO) nanoparticles (NPs) were developed and characterized for the detection of low concentrations of atmospheric pollutants, such as nitrogen dioxide (NO2) and carbon monoxide (CO). The sensing layers were prepared using three fabrication methods: drop-casting, electrospray, and spark ablation coupled with an inertial impaction printer, to compare their performance. Multiple surface characterization techniques were carried out to investigate the surface morphology and elemental composition of the deposited layers such as SEM (scanning electron microscopy) and XPS (X-ray photoelectron spectroscopy) analyses. UV light photoactivation enabled the sensors to detect ultra-low concentrations of the target gases at room temperature (100 ppb NO2 and 1 ppm CO). The measurements were conducted at 50% relative humidity to simulate real environmental conditions. All sensors were capable of detecting the target gases. Drop-casting is the simplest and most cost-effective technique, but it is also the least reproducible. In contrast, sensors based on the spark ablation technique achieved more homogeneous sensing layers, with practically no nanoparticle agglomeration, resulting in devices with lower noise and drift in their electrical response., This work was supported by project TED2021-131114B-C22, financed by European Union NextGenerationEU/PRTR, and PID2023-151565OB-C42, funded by MICIU/AEI/10.13039/501100011033 and FEDER, UE., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thermally annealed MoS2 nanosheets for highly sensitive NO2 detection: Role of vacancies and heterojunctions

  • Sayago, Isabel
  • Santos, José Pedro
  • Sánchez-Vicente, Carlos
  • Ogilvie, Sean P.
  • Dalton, Alan B.
  • Muñoz, Edgar
  • Garriga, Rosa
This work describes the facile, cost-effective fabrication of MoS2-based resistive sensors for low concentration detection of NO2. The sensitive layer consists of films of liquid-phase exfoliated MoS2 nanosheets in aqueous medium deposited by drop-casting onto micromachined silicon substrates with integrated heaters. Thermal treatment of MoS2 conducted during sensor preparation generates high density of S vacancies and induces partial oxidation to non-stoichiometric MoO3-x, resulting in the formation of both S vacancies in MoS2 and O vacancies in the oxide phase. Vacancies act as high-energy binding sites for NO2 and facilitate charge transfer, which enhances the NO2 sensing performance. In addition, the MoS2/MoO3-x heterojunctions formed lead to amplified change in conductivity upon NO2 adsorption, thereby enhancing the overall sensing response. Precise control of oxidation is a key issue, since excessive oxidation may both passivate vacancy sites and decrease the electrical conductivity of the sensing layer through the formation of less conductive oxide phase. The facile fabrication method reported here provided competitive sensor performance: NO2 concentration as low as 0.5 ppm was measured at 200 °C, and 0.25 ppm at 300 °C. Additionally, these sensors showed remarkable selectivity to NO2 with negligible responses to interfering gases (acetone, ethanol and CO). The effect of humidity on sensor response was studied, and it was found that 50% RH humidity significantly enhances the sensing response to NO2. The incorporation of carbon nanotubes to the sensing layers resulted in a faster and higher response to NO2. Detection mechanisms involved are discussed here.