Pasar al contenido principal

MAXIMIZACION DE LA EFICIENCIA Y MINIMIZACION DEL IMPACTO AMBIENTAL DE BOMBAS DE CALOR PARA LA DESCARBONIZACION DE LA CALEFACCION/ACS EN LOS EDIFICIOS DE CONSUMO CASI NULO

PRE2018-083535

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of lubricant in the performance of variable speed heat pumps working with R290, Impact du lubrifiant sur les performances des pompes à chaleur à vitesse variable fonctionnant au R290

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Barta, Riley B.
[EN] Modulating the speed of the compressors and adapting its capacity to the required load has led to a decrease in the annual energy consumption in many applications. However, in the compressor, having adequate lubrication at low speeds usually implies discharging too much lubricant at higher speeds. Although necessary for compressor operation, lubricating oil acts as a contaminant in the rest of the system. Consequently, manufac- turers have to consider the oil circulation rate (OCR), as it limits the speed range of the compressor. In a previous study, a compressor was tested over its speed range (30 - 110 Hz), working with R290 and POE68 as a lubricant. Experimental data confirm the increase of OCR with speed and suggests that working with R290-POE68 could imply higher OCR values compared to other refrigerant-oil mixtures. In this study, the impact of the OCR in the performance of a R290 heat pump was theoretically assessed. Three contributions were studied: The heat transfer coefficient (HTC) reduction in the evaporator, the effect of refrigerant being solved in oil and finally, and the impact of oil in the compressor. It was found that OCR values of 5% could decrease the coefficient of performance (COP) by more than 20%., The authors would like to acknowledge the Spanish ' MINISTERIO DE ECONOMIA Y COMPETITIVIDAD' , through the project ref- ENE2017 - 83665-C2 - 1-P 'Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/acs en los edificios de consumo casi nulo' for the given support. In addition, Ruben Ossorio would like to thank the Spanish government for his PhD scholarship with reference PRE2018 - 083535.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of oil circulation rate in variable speed scroll compressor working with propane, Étude du débit de circulation de l&apos, huile dans un compresseur à spirales à vitesse variable fonctionnant au propane

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] The use of hydrocarbons as refrigerants is being more common in recent years. Nevertheless, the solubility of propane in POE oils is significantly higher than in HFCs. This fact has made that POE oils used with hydrocarbons usually have a higher viscosity than the commonly used with HFCs. This approach solves the lubrication problem in the compressor but the way in which oil could affect the system performance is not so widely studied. In this work, an experimental analysis about the oil circulation rate of a variable speed compressor working with propane has been done. The study has analysed the oil circulation at different compressor speeds and evaporating temperatures. The obtained results have shown that the oil circulation rate increases with the compressor speed and reaches values higher than 5% at high speeds. This fact can penalize the COP of the system in more than 15% in these working conditions., The authors would like to acknowledge the Spanish "Ministerio De Economia Y Competitividad", through the project ref-ENE2017-83665-C2-1-P "Maximizacion de la eficiencia y minimizacion del impacto ambiental de bombas de calor para la descarbonizacion de la calefaccion/ACS en los edificios de consumo casi nulo" for the given support. In addition, Ruben Ossorio would like to thanks to the Spanish government his PhD scholarship PRE2018-083535.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Testing of Variable-Speed Scroll Compressors and their inverters for the evaluation of compact energy consumption models

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] Prediction models for energy consumption in heat pumps are critical for design, selection, control and fault detection. However, nowadays, the methodology for characterizing variable-speed compressors has not been standardized, and typically the pair compressor-inverter is studied as a whole. In this study, disaggregated energy consumption results of compressor and inverter are provided by using a double-wattmeter scheme. These results are used to compare the performance of existing models and to establish guidelines to define testsmatrixes as compact as possible to characterize this type of compressors. The widely used 20-coefficient correlation can overfit the compressor behaviour when fitted with an small dataset, introducing significant deviations when extrapolating. Optimal Design methodologies to create rating test matrixes gave excellent results compared with classical clustering techniques. Regarding inverter results, a compact empirical model was proposed to model inverter power losses depending on total consumption and compressor speed. The proposed model used only five fitting coefficients, and most predictions are inside a 5% error band for all tested inverters. Finally, the tested compressors and inverters suffered a significant efficiency loss at very low speeds, which could make cycling more profitable under certain circumstances., The authors would like to acknowledge the Spanish "MINISTERIO DE ECONOMIA Y COMPETITIVIDAD", through the project ref-ENE2017-83665-C2-1-P "Maximizacion de la eficiencia y minimizacion del impacto ambiental de bombas de calor para la descarbonizacion de la calefaccion/acs en los edificios de consumo casi nulo" for the given support. In addition, Ruben Ossorio would like to thank the Spanish government for his PhD scholarship with reference PRE2018-083535.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A novel methodology to assist manufacturers in the heat exchanger sizing for variable-speed heat pumps based on part load conditions and economic assessment

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
[EN] Matts Bäckstöm assessed the selection criteria of heat exchangers for single-speed heat pumps in 1940, and his methodology and conclusions have been kept practically unchanged for almost a century. However, heat pump systems have evolved, especially with the introduction of variable-speed heat pumps. These new systems introduced a new degree of freedom to the heat pump design ¿ the compressor speed ¿ which is not considered by traditional design criteria. This study proposes novel design criteria to optimize the heat exchanger size when the heat pump unit can work under part-load conditions. The proposed method models how heat exchangers and variable-speed compressors perform under different loads and sizes. It considers part-load requirements based on climatic data (which are typically available in the standards) and considers economic factors such as initial investment and operation costs (which are dependent on the components's size). Given the mentioned information, a multivariable optimization algorithm is implemented to find the optimum heat exchanger size that minimizes the total cost. To validate the proposed approach's effectiveness, it was exemplified by determining the optimum size of a coil and a plate heat exchanger for a domestic variable-speed heat pump. The results demonstrate that using traditional criteria could lead to over-dimensioning heat exchangers in variable-speed heat pumps which could incur in an increase of costs of 5% for the studied case.