Pasar al contenido principal

APROVECHAMIENTO DE BIOMASA Y PRODUCCION SOSTENIBLE DE ENERGIA MEDIANTE (FOTO)CATALIZADORES Y REACTORES ESTRUCTURADOS BASADOS EN MATERIALES CARBONOSOS

PRE2018-086557

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogen and CNT production by methane cracking using Ni–Cu and Co–Cu catalysts supported on argan-derived carbon

  • Cazaña, Fernando
  • Afailal, Zainab
  • González-Martín, Miguel
  • Sánchez, José Luis
  • Latorre, Nieves
  • Romeo, Eva
  • Arauzo, Jesús
  • Monzón, Antonio
This article belongs to the Special Issue A Themed Issue in Honor of Prof. Dr. Vicente Rives., The 21st century arrived with global growth of energy demand caused by population and standard of living increases. In this context, a suitable alternative to produce COx-free H2 is the catalytic decomposition of methane (CDM), which also allows for obtaining high-value-added carbonaceous nanomaterials (CNMs), such as carbon nanotubes (CNTs). This work presents the results obtained in the co-production of COx-free hydrogen and CNTs by CDM using Ni–Cu and Co–Cu catalysts supported on carbon derived from Argan (Argania spinosa) shell (ArDC). The results show that the operation at 900 °C and a feed-ratio CH4:H2 = 2 with the Ni–Cu/ArDC catalyst is the most active, producing 3.7 gC/gmetal after 2 h of reaction (equivalent to average hydrogen productivity of 0.61 g H2/gmetal∙h). The lower productivity of the Co–Cu/ArDC catalyst (1.4 gC/gmetal) could be caused by the higher proportion of small metallic NPs (<5 nm) that remain confined inside the micropores of the carbonaceous support, hindering the formation and growth of the CNTs. The TEM and Raman results indicate that the Co–Cu catalyst is able to selectively produce CNTs of high quality at temperatures below 850 °C, attaining the best results at 800 °C. The results obtained in this work also show the elevated potential of Argan residues, as a representative of other lignocellulosic raw materials, in the development of carbonaceous materials and nanomaterials of high added-value., Grant PID2020-113809RB-C31 funded by MCIN/AEI/10.13039/501100011033; grant PLEC2021-008086 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR; grant PRE2018-086557 funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Experimental and kinetic study of bimetallic Pd-based catalysts for selective reduction of nitrates in aqueous phase

  • González-Martín, Miguel
Programa de Doctorado en Ingeniería Química y del Medio Ambiente., [EN] Population growth and the need to supply a high demand for food has led to inefficient production and use of fertilisers leading to nitrate pollution in water, with the danger, among others, of causing cancer or blue baby syndrome in humans. Despite extensive legislation on nitrate, nitrite and ammonium pollution, nitrate, nitrite and ammonium contamination is widespread worldwide. However, an optimal industrial-scale method to solve this problem with the lowest possible drawback has not yet been found. Among the existing methods, selective catalytic nitrate reduction shows great potential to decompose nitrates into nitrogen gas, an inert and harmless gas, in a short period of time, in a reduced space and without producing other products that require further treatment, as brines or sludge. The main goal of this Doctoral Thesis has been to extend the knowledge on the influence of the operating variables of reaction, and of the composition and properties of the catalysts on their activity, stability and selectivity. To fulfil this purpose, different PdCu and PdSn catalysts supported on γ-alumina, and PdCu catalysts supported on a commercial graphite (Asbury-4124®) modified with thermal and chemical treatments have been synthesized. After the synthesis of these catalysts, physico-chemical characterization of the catalysts was carried out to know the influence of synthesis variables studied on the catalyst properties and subsequently on its catalytic performance. The techniques used were: X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Nitrogen adsorption analysis, Temperature programmed reduction (TPR), Atomic absorption spectroscopy (AAS), Temperature programmed desorption coupled to a mass spectrometer (TPD-MS), Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS). A series of PdCu/Al2O3 catalysts were synthesized fixing the Cu content at 0.4% w.t. and varying the Pd content between 0.25, 0.5, 0.75 and 1% w.t. Using these catalysts, the influence of the amount of noble metal in the catalyst was studied. Furthermore, using the 1Pd0.4Cu/Al2O3 catalyst, the influence of the stirring speed was studied by varying it from 520 rpm to 1500 rpm. After that, the influence of the catalyst loading on the reaction was studied by introducing catalyst concentrations from 0.25g/L to 2g/L. The influence of the ratio of H2 and CO2 in the feed was also studied, in this case the ratio of H2 and CO2 in the feed was varied while the total flow remained constant at 900 Nml/min. To study the influence of the ions in the dissolution, a catalytic study was carried out using 3 different types of water: distilled water, mineral water and tap water. Finally, using the 1Pd0.4Cu/Al2O3 catalyst, a study of the combination of the catalytic selective reduction of nitrates in conjunction with Amberlite® H + cation exchange resins was carried out, varying the load of cation exchange resin introduced from 0g to 6g of resin. Using the same Al2O3 support, a series of catalysts was synthesized using Sn as promoter metal. In this case, first two catalysts were prepared with 1%Pd w.t. and 0.4%Sn w.t. varying the order of impregnation of the metals. After this first test, it was decided to continue the synthesis with a first Sn impregnation followed by Pd impregnation. After that, the studies continued with the amount of promoter metal in the catalyst varying the amount of Sn between 0.2 and 2.5% w.t. and fixing 1% of Pd. Subsequently, the amount of Sn was fixed at 1.2% w.t. and the influence of the amount of Pd was studied, varying this percentage between 0.6 and 4% w.t. The results obtained were similar to those obtained in the case of the PdCu/Al2O3 study. After these tests, it was decided to use the 1Pd1.2Sn/Al2O3 catalyst to study the influence of the ratio of H2 and CO2 in the feed by varying the ratio between these two gases in the feed, however in this case the H2 flow rate was kept constant at 100NmL/min and the CO2 flow rate was varied from 0 to 400 NmL/min. In the same way as for PdCu/Al2O3, the influence of ions in water was studied using distilled water and tap water in the reaction. Finally, the influence of the reduction temperature of the catalyst prior to the reaction was studied by varying the reduction temperature from 250ºC to 550ºC. The last studies were carried out using the catalysts synthesized with commercial graphite (Asbury® 4124). In this case six catalysts were synthesized: three were synthesized in reducing atmosphere using a flow rate of 300NmL/min and a H2/N2 ratio of 1, while the other 3 were synthesized in an oxidizing atmosphere using an air flask. In addition, four of these catalysts were modified by chemical treatments, two of the catalysts (one in a reducing atmosphere and one in an oxidizing atmosphere) were coimpregnated with urea during the synthesis, while the other two (one in a reducing atmosphere and one in an oxidizing atmosphere) were subjected to oxidation with HNO3 prior to impregnation with the metals. All these catalysts were then tested in the selective catalytic reduction of nitrates. Using all these results, a kinetic model has been developed and adjusted to take into account the evolution of the main reactants and products, nitrates, nitrites, ammonium and nitrogen gas. In addition, this model takes into account the possible deactivation of the catalyst, the evolution of the intermediate compound NO or the reconversion of NO to NO2-. This model has even been modified to take into account the presence of cation exchange resins, all of which has allowed us to quantify the influence of the different variables and deepen our knowledge of the reaction. This model allows the simultaneous calculation of the evolution of all relevant species: NO3-, NO2-, NO, N2 and NH4+. The calculation of the kinetic parameters has been made by a multi-response non-linear regression procedure, solving numerically the set of differential-algebraic equations proposed., [ES] El crecimiento de la población y la necesidad de abastecer una gran demanda de alimentos ha llevado a una producción y uso ineficientes de fertilizantes que provocan la contaminación del agua por nitratos, con el peligro, entre otros, de causar cáncer o el síndrome del bebé azul en humanos. A pesar de la amplia legislación sobre contaminación por nitratos, nitritos y amonio, la contaminación por nitratos, nitritos y amonio está muy extendida en todo el mundo. Sin embargo, aún no se ha encontrado un método óptimo a escala industrial para resolver este problema. Entre los métodos existentes, la reducción catalítica selectiva de nitratos muestra un gran potencial para descomponer los nitratos en nitrógeno gas, un gas inerte e inocuo, en un corto periodo de tiempo, en un espacio reducido y sin producir otros productos que requieran tratamiento posterior, como salmueras o lodos. El objetivo principal de esta Tesis Doctoral ha sido ampliar el conocimiento sobre la influencia de las variables operativas de reacción, y de la composición y propiedades de los catalizadores en su actividad, estabilidad y selectividad. Para ello se han sintetizado diferentes catalizadores de PdCu y PdSn soportados sobre γalúmina, y catalizadores de PdCu soportados sobre un grafito comercial (Asbury4124®) modificado con tratamientos térmicos y químicos. Tras la síntesis de estos catalizadores, se llevó a cabo la caracterización físico-química de los mismos para conocer la influencia de las variables de síntesis estudiadas sobre las propiedades del catalizador y posteriormente sobre su rendimiento catalítico. Las técnicas utilizadas fueron: Difracción de rayos X (XRD), Microscopía electrónica de barrido (SEM), Microscopía electrónica de transmisión (TEM), Análisis de adsorción de nitrógeno, Reducción programada por temperatura (TPR), Espectroscopía de absorción atómica (AAS), Desorción programada por temperatura acoplada a un espectrómetro de masas (TPD-MS), Espectroscopía Raman (Raman) y Espectroscopía de fotoelectrones de rayos X (XPS). Se sintetizaron una serie de catalizadores PdCu/Al2O3 fijando el contenido de Cu al 0.4% en peso y variando el contenido de Pd entre 0.25, 0.5, 0.75 y 1% en peso. Utilizando estos catalizadores, se estudió la influencia de la cantidad de metal noble en el catalizador. Además, utilizando el catalizador 1Pd0.4Cu/Al2O3, se estudió la influencia de la velocidad de agitación variándola de 520 rpm a 1500 rpm. A continuación, se estudió la influencia de la carga de catalizador en la reacción introduciendo concentraciones de catalizador de 0.25g/L a 2g/L. También se estudió la influencia de la proporción de H2 y CO2 en la alimentación, en este caso se varió la proporción de H2 y CO2 en la alimentación mientras que el caudal total se mantuvo constante a 900 Nml/min. Para estudiar la influencia de los iones en la disolución, se realizó un estudio catalítico utilizando 3 tipos diferentes de agua: agua destilada, agua mineral y agua del grifo. Por último, utilizando el catalizador 1Pd0.4Cu/Al2O3, se realizó un estudio de la combinación de la reducción selectiva catalítica de nitratos junto con resinas de intercambio catiónico Amberlite® H+, variando la carga de resina de intercambio catiónico introducida desde 0g hasta 6g de resina. Utilizando el mismo soporte de Al2O3, se sintetizó una serie de catalizadores empleando Sn como metal promotor. En este caso, los dos primeros catalizadores se prepararon con 1%Pd en peso y 0.4%Sn en peso variando el orden de impregnación de los metales. Tras esta primera prueba, se decidió continuar la síntesis con una primera impregnación de Sn seguida de la impregnación de Pd. Después, los estudios continuaron con la cantidad de metal promotor en el catalizador variando la cantidad de Sn entre 0.2 y 2.5% en peso y fijando un 1% de Pd. Posteriormente, se fijó la cantidad de Sn en 1.2% en peso y se estudió la influencia de la cantidad de Pd, variando este porcentaje entre 0.6 y 4%. Los resultados obtenidos fueron similares a los obtenidos en el caso del estudio de PdCu/Al2O3. Tras estas pruebas, se decidió utilizar el catalizador 1Pd1.2Sn/Al2O3 para estudiar la influencia de la relación de H2 y CO2 en la alimentación variando la relación entre estos dos gases en la alimentación, sin embargo, en este caso el caudal de H2 se mantuvo constante en 100NmL/min y el caudal de CO2 se varió de 0 a 400 NmL/min. De la misma manera que para PdCu/Al2O3, se estudió la influencia de los iones en el agua utilizando agua destilada y agua del grifo en la reacción. Por último, se estudió la influencia de la temperatura de reducción del catalizador antes de la reacción variando la temperatura de reducción de 250ºC a 550ºC. Los últimos estudios se realizaron utilizando los catalizadores sintetizados con grafito comercial (Asbury® 4124). En este caso se sintetizaron seis catalizadores: tres se sintetizaron en atmósfera reductora utilizando un caudal de 300NmL/min y una relación H2/N2 de 1, mientras que los otros 3 se sintetizaron en atmósfera oxidante utilizando un matraz de aire. Además, cuatro de estos catalizadores se modificaron mediante tratamientos químicos, dos de los catalizadores (uno en atmósfera reductora y otro en atmósfera oxidante) se coimpregnaron con urea durante la síntesis, mientras que los otros dos (uno en atmósfera reductora y otro en atmósfera oxidante) se sometieron a oxidación con HNO3 antes de la impregnación con los metales. A continuación, todos estos catalizadores se ensayaron en la reducción catalítica selectiva de nitratos. A partir de todos estos resultados, se ha desarrollado y ajustado un modelo cinético que tiene en cuenta la evolución de los principales reactivos y productos, nitratos, nitritos, amonio y nitrógeno gas. Además, este modelo tiene en cuenta la posible desactivación del catalizador, la evolución del compuesto intermedio NO o la reconversión de NO en NO2-. Este modelo ha sido incluso modificado para tener en cuenta la presencia de resinas de intercambio catiónico, todo lo cual ha permitido cuantificar la influencia de las distintas variables y profundizar en el conocimiento de la reacción. Este modelo permite calcular simultáneamente la evolución de todas las especies relevantes: NO3-, NO2-, NO, N2 y NH4+. El cálculo de los parámetros cinéticos se ha realizado mediante un procedimiento de regresión no lineal multirrespuesta, resolviendo numéricamente el conjunto de ecuaciones diferenciales-algebraicas propuestas., Me gustaría agradecer al Ministerio de Ciencia, Innovación y Universidades por la concesión de mi beca FPI (PRE2018-086557) gracias al cual he podido realizar este trabajo de investigación. Y a los proyectos “Aprovechamiento de biomasa y producción sostenible de energía mediante (foto)catalizadores y reactores estructurados basados en materiales carbonosos” (ENE2017-82451-C3-1-R) y “Catalizadores Basados en Carbón Derivado de Biomasa para la Producción y Uso de Hidrógeno Verde” (PID2020-113809RB-C31)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogen and CNT production by methane cracking using Ni–Cu and Co–Cu catalysts supported on argan-derived carbon

  • Cazaña, Fernando
  • Afailal, Zainab
  • González-Martín, Miguel
  • Sánchez, José Luis
  • Latorre, Nieves
  • Romeo, Eva
  • Arauzo, Jesús
  • Monzón, Antonio
The 21st century arrived with global growth of energy demand caused by population and standard of living increases. In this context, a suitable alternative to produce COx-free H2 is the catalytic decomposition of methane (CDM), which also allows for obtaining high-value-added carbonaceous nanomaterials (CNMs), such as carbon nanotubes (CNTs). This work presents the results obtained in the co-production of COx-free hydrogen and CNTs by CDM using Ni–Cu and Co–Cu catalysts supported on carbon derived from Argan (Argania spinosa) shell (ArDC). The results show that the operation at 900 °C and a feed-ratio CH4:H2 = 2 with the Ni–Cu/ArDC catalyst is the most active, producing 3.7 gC/gmetal after 2 h of reaction (equivalent to average hydrogen productivity of 0.61 g H2/gmetal∙h). The lower productivity of the Co–Cu/ArDC catalyst (1.4 gC/gmetal) could be caused by the higher proportion of small metallic NPs (<5 nm) that remain confined inside the micropores of the carbonaceous support, hindering the formation and growth of the CNTs. The TEM and Raman results indicate that the Co–Cu catalyst is able to selectively produce CNTs of high quality at temperatures below 850 °C, attaining the best results at 800 °C. The results obtained in this work also show the elevated potential of Argan residues, as a representative of other lignocellulosic raw materials, in the development of carbonaceous materials and nanomaterials of high added-value.