Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Airborne ultrasonic application on hot air-drying of pork liver. Intensification of moisture transport and impact on protein solubility

  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Bon Corbín, José|||0000-0002-0457-9705
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Abril-Gisbert, Blanca
  • Toldrà, M.
  • Parés, D.
[EN] Nowadays, there is increasing interest in developing strategies for the efficient and sustainable use of animal byproducts, such as pork liver. In order to stabilize the product, a prior dehydration stage may be required due to its high perishability. The water removal process of pork liver is energy costly and time consuming, which justifies its intensification using novel technologies. In this sense, the aim of this study was to assess the effect of the airborne application of power ultrasound on the hot air-drying of pork liver. For that purpose, drying experiments were carried out at 30, 40, 50, 60 and 70 ?C on pork liver cylinders at 2 m.s(-1) with (US) and without ultrasonic application (AIR). The drying process was modeled from the diffusion theory and, in the dried pork liver, the protein solubility was analyzed in order to determine the effect of drying on the protein quality. The ultrasound application increased the drying rate, shortening the drying time by up to 40% at 30 ?C. The effect of power ultrasound at high temperatures (60 and 70 ?C) was of lesser magnitude. Drying at 70 ?C involved a noticeable reduction in the protein solubility for dried liver, while the impact of ultrasound application on the solubility was not significant (p > 0.05)., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad (MINECO)" and "Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Project RTA2017-00024-C04-03) . Eduardo A. Sanchez-Torres acknowledges the FPU PhD contract (FPU18/01439) granted by the Spanish Ministry of Science, Innovation and Universities. Funding for open access charge: Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of ultrasonic application on the enzymatic formation of zinc protoporphyrin

  • Abril-Gisbert, Blanca
  • Bou, R.
  • Llauger, M.
  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Ferrochelatase (FeCH), present in pork liver, catalyses the formation of zinc-protoporphyrin (ZnPP), a stable purple-red pigment found in Parma ham. Kinetics of ZnPP formation is especially slow. Thus, the aim of this study was to improve the ZnPP production using power ultrasound (US) at low (7.05 W/L) and moderate power (36.53 W/L) in homogenised pork liver (HLi) and with added oxyhemoglobin (HLi + OxyHb). ZnPP formation was performed at 37 degrees C, under anaerobic conditions, for different reaction times (6-48 h). When US was applied at low power, it shortened the time needed to reach maximum ZnPP formation by 50% and increased the yield by 25.77% in the case of HLi and by 4.42% in that of HLi + OxyHb, when compared to the control experiments; however, for the moderate power, ZnPP formation was hindered. Therefore, low power US proved to be an effective method with which to intensify enzymatic ZnPP production., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad (MINECO) and Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Project RTA 2017-00024-C04-03). The authors acknowledge the contribution of the slaughterhouse "Carnes de Teruel S.A." (D.O. Jamon de Teruel, Spain) for the supply of pork livers.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Aplicación de tecnologías emergentes para la obtención de Zinc-protoporfirina y proteínas funcionales a partir de co-productos cárnicos

  • Abril Gisbert, Blanca
[ES] El hígado de cerdo es un coproducto de origen animal que contiene una elevada cantidad de proteínas, así como otros compuestos de interés, entre los que destacan las enzimas como la ferroquelatasa (FeQ). La FeQ actúa como catalizadora en la formación del pigmento zinc protoporfirina (ZnPP), responsable del color característico del jamón de Parma y que puede resultar relevante en la elaboración de productos cárnicos crudo-curados. Así, en la presente Tesis Doctoral se va a estudiar la aplicación de tecnologías emergentes, como los ultrasonidos (US), para favorecer la extracción de la enzima FeQ y para la mejora de la formación del pigmento ZnPP. Asimismo, con el objetivo de la valorización del hígado como fuente de proteínas, en primer lugar se estudiará su estabilización mediante el secado convectivo, a un amplio rango de temperaturas, para optimizar el producto (fracción proteica). Posteriormente, el hígado deshidratado se desgrasará y desodorizará utilizando técnicas convencionales como el arrastre por vapor con aplicación de vacío (AVV) y CO2 supercríticos (CO2-SC), para lograr un producto rico en proteínas que sea aceptable organolépticamente por el consumidor. Los resultados experimentales mostraron que la aplicación de US intensificó en gran medida la extracción de la enzima FeQ del hígado de cerdo. Así, la aplicación de US durante la extracción de FeQ condujo a una mejora de la actividad enzimática y consecuentemente a un aumento de la formación de ZnPP. En cuanto a la formación de ZnPP asistida por US a partir hígado homogeneizado (Hhc) e hígado homogeneizado, con adición de oxihemoglobina (Hhc+OxiHb), el máximo de ZnPP formado cuando se aplicaron US a baja potencia (7.05 W/L) fue de 0.405 mmol ZnPP/L en Hhc y 0.449 mmol ZnPP/L en Hhc+OxiHb, alcanzándose este valor a las 12 h, mientras que sin aplicación de US el máximo se alcanzó a las 24 h, siendo éste de 0.322 mmol ZnPP/L en Hhc y 0.430 mmol ZnPP/L en Hhc+OxiHb. Sin embargo, cuando se aplicaron US a moderada potencia (36.53 W/L) fue solo de 0.037 mmol ZnPP/L a 24 h de incubación, debido a que el sistema de control de temperatura no pudo ser controlado. En relación al secado de hígado de cerdo a diferentes temperaturas (de -10 a 70ºC), los resultados revelaron que el aumento de la temperatura de secado influyó tanto en la actividad enzimática como en la concentración de FeQ aparente. Así, la condición óptima se encontró en el rango de 10 a 20ºC. Además, la temperatura de secado y el desgrasado también influyó en las propiedades fisicoquímicas y tecno-funcionales del hígado de cerdo, siendo la temperatura de 40ºC la que conllevó una menor degradación de proteínas en comparación con el deshidratado a 70ºC. En cuanto a la desodorización, los resultados mostraron que ambas técnicas (AVV y CO2-SC) fueron eficaces en la reducción y eliminación compuestos volátiles (COVs) característicos del hígado del cerdo. A través del AVV se redujo el contenido de COVs se redujo en su conjunto un 67.5%, mientras que mediante CO2-SC se redujo un 81.2%, con respecto al hígado de cerdo deshidratado sin desodorizar. Además, tras la aplicación de CO2-SC se eliminaron COVs característicos del olor desagradable del hígado de cerdo. Asimismo, mediante la extracción con CO2-SC se redujo el contenido de grasa un 24.9%, en comparación con la muestra sin desodorizar. Así pues, se puede concluir que las tecnologías emergentes como los US mejoraron el proceso de extracción de FeQ, así como su actividad enzimática en la formación de ZnPP. Además, mediante el secado y desgrasado del hígado, es posible alargar la vida útil del hígado. Así, a partir del hígado deshidratado se extrajo FeQ con actividad catalítica para la formación del pigmento ZnPP, y a partir del hígado deshidratado-desgrasado se recuperó la fracción proteica, la cual presentaba excelentes propiedades fisicoquímicas y tecno-funcionales. La extracción mediante CO2-SC resultó ser una alternativa a la técnica AVV para la desodorización., [CA] El fetge de porc és un coproducte d'origen animal que conté una elevada quantitat de proteïnes, així com altres compostos d'interès, entre els quals destaquen els enzims com la ferroquelatasa (FeQ). La FeQ actua com a catalitzadora en la formació del pigment zinc protoporfirina (ZnPP), responsable del color característic del pernil de Parma i que pot resultar rellevant en l'elaboració de productes carnis crucurats. Així, en aquesta Tesi Doctoral s'estudiarà l'aplicació de tecnologies emergents, com els ultrasons (US), per afavorir l'extracció de l'enzim FeQ i per a la millora de la formació del pigment ZnPP. Així mateix, amb l'objectiu de la valorització del fetge com a font de proteïnes, en primer lloc se n'estudiarà l'estabilització mitjançant l'assecatge convectiu, a un ampli rang de temperatures, per optimitzar el producte (fracció proteica). Posteriorment, el fetge deshidratat es desgreixarà i desodoritzarà utilitzant tècniques convencionals com l'arrossegament per vapor amb aplicació de buit (AVV) i CO2 supercrítics (CO2-SC), per aconseguir un producte ric en proteïnes que sigui acceptable organolèpticament pel consumidor. Els resultats experimentals van mostrar que l'aplicació US va intensificar en gran mesura l'extracció de l'enzim FeQ del fetge de porc. Així, l'aplicació US durant l'extracció de FeQ va conduir a una millora de l'activitat enzimàtica i conseqüentment a un augment de la formació de ZnPP. Quant a la formació de ZnPP assistida per US a partir fetge homogeneïtzat (Hfp) i fetge homogeneïtzat, amb addició de oxihemoglobina (Hfp+OxiHb) , el màxim de ZnPP format quan es van aplicar US a baixa potència (7.05 W/L) va ser de 0.405 mmol ZnPP/L a Hhc i 0.449 mmol ZnPP /L a Hhc+OxiHb, assolint-se aquest valor a les 12 h, mentre que sense aplicació d'US el màxim es va assolir a les 24 h, sent aquest de 0.322 mmol ZnPP/L a Hhc i 0.430 mmol ZnPP/L a Hhc+OxiHb . Tot i això, quan es van aplicar US a moderada potència (36.53 W/L) va ser només de 0.037 mmol ZnPP/L a 24 h d'incubació, pel fet que el sistema de control de temperatura no va poder ser controlat. Pel que fa a l'assecatge de fetge de porc a diferents temperatures (de -10 a 70ºC), els resultats van revelar que l'augment de la temperatura d'assecatge va influir tant en l'activitat enzimàtica com en la concentració de FeQ aparent. Així, la condició òptima es va trobar al rang de 10 a 20ºC. A més, la temperatura d'assecatge i el desgreixat també va influir en les propietats fisicoquímiques i tecnofuncionals del fetge de porc, sent la temperatura de 40ºC la que va comportar una menor degradació de proteïnes en comparació del deshidratat a 70ºC. Pel que fa a la desodorització, els resultats van mostrar que ambdues tècniques (AVV i CO2-SC) van ser eficaces en la reducció i eliminació compostos volàtils (COVs) característics del fetge del porc. A través de l'AVV es va reduir el contingut de COVs es va reduir en conjunt un 67.5%, mentre que mitjançant CO2-SC es va reduir un 81.2%, respecte al fetge de porc deshidratat sense desodoritzar. A més, després de l'aplicació de CO2-SC es van eliminar COV característics de l'olor desagradable del fetge de porc. Així mateix, mitjançant l'extracció amb CO2-SC es va reduir el contingut de greix un 24.9%, en comparació de la mostra sense desodoritzar. Així doncs, es pot concloure que les tecnologies emergents com els US van millorar el procés d'extracció de FeQ, així com la seva activitat enzimàtica a la formació de ZnPP. A més, mitjançant l'assecatge i desgreixatge del fetge, és possible allargar la vida útil del fetge. Així, a partir del fetge deshidratat es va extreure FeQ amb activitat catalítica per a la formació del pigment ZnPP, ia partir del fetge deshidratat-desgreixat es va recuperar la fracció proteica del fetge, la qual presentava excel·lents propietats fisicoquímiques i tecnofuncionals. L'extracció mitjançant CO2-SC va resultar ser una alternativa a la tècnica de AVV per a la desodorització., [EN] Pork liver is a co-product of animal origin that contains a high amount of protein, as well as other compounds of interest, among which enzymes such as ferrochelatase (FeCH). FeCH acts as a catalyst in the formation of the pigment zinc protoporphyrin (ZnPP), responsible for the characteristic color of Parma ham and which may be relevant in the production of raw-cured meat products. Thus, in this Doctoral Thesis, the application of emerging technologies, such as ultrasound (US), will be studied to favor the extraction of the FeCH enzyme and to improve the formation of the ZnPP pigment. Likewise, with the aim of valorizing the liver as a source of protein, its stabilization by means of convective drying will first be studied, at a wide range of temperatures, to optimize the product (protein fraction). Subsequently, the dehydrated liver will be defatted and deodorized using conventional techniques such asvacuum steam distillation (VSD) and supercritical CO2 (SC-CO2), to achieve a protein-rich product that is organoleptically acceptable to the consumer. The experimental results showed that the application of US greatly enhanced the extraction of FeCH enzyme from pork liver. Thus, the application of US during the FeCH extraction led to an improvement in the enzymatic activity and consequently to an increase in the ZnPP formation. Regarding US-assisted ZnPP formation from homogenized pork liver (HLi) and homogenized pork liver, with the addition of oxyhemoglobin (HLi+OxyHb, the maximum ZnPP formed when US was applied at low power (7.05 W/L) was 0.405 mmol ZnPP/L in Hhc and 0.449 mmol ZnPP /L in Hhc+OxyHb, reaching this value at 12 h, while without application of US the maximum was reached at 24 h, being 0.322 mmol ZnPP/L in Hhc and 0.430 mmol ZnPP/L in Hhc+OxyHb. However, when US was applied at moderate power (36.53 W/L) it was only 0.037 mmol ZnPP/L at 24 h of incubation, because the temperature control system could not be controlled. Regarding the drying of pig liver at different temperatures (from -10 to 70ºC), the results revealed that the increase in the drying temperature influenced both the enzymatic activity and the apparent FeCH concentration. Thus, the optimal condition was found in the range of 10 to 20ºC. In addition, the drying temperature and defatting also influenced the physicochemical and techno-functional properties of pork liver, being the temperature of 40ºC the one that led to less protein degradation compared to that dehydrated at 70ºC. Regarding deodorization, the results showed that both techniques (VSD and SC-CO2) were effective in reducing and eliminating volatile compounds (VOCs) characteristic of pig liver. Through AVV the content of VOCs was reduced as a whole by 67.5%, while through SC-CO2 towas reduced by 81.2%, with respect to dried pork liver without deodorizing. In addition, after the application of SC-CO2, VOCs characteristic of the unpleasant odor of pig liver were eliminated. Likewise, by extraction with SC-CO2, the fat content was reduced by 24.9%, compared to the sample without deodorization. Thus, it can be concluded that emerging technologies such as US improved the FeCH extraction process, as well as its enzymatic activity in the ZnPP formation. Furthermore, by drying and defatting the liver, it is possible to extend the lifespan of the liver. Thus, from the dehydrated liver, FeCH was extracted with catalytic activity for the formation of the ZnPP pigment, and from the dried-defatted liver, the protein fraction of the liver was recovered, which presented excellent physicochemical and techno-functional properties. The SC-CO2 extraction turned out to be an alternative to the VSD technique for the deodorization., The authors acknowledge the financial support from the “Ministerio de Economía y Competitividad (MINECO)” and “Instituto Nacional de Investigación y Tecnología Agraria y Alimentaria (INIA)” in Spain (Projects RTA2017-00024-C04-03 and RTA2017-00024-C04-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of pork liver drying on ferrochelatase activity for zinc protoporphyrin formation

  • Abril-Gisbert, Blanca
  • Bou, R.
  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
[EN] Pork liver contains an endogenous enzyme, ferrochelatase (FeCH), which catalyses the formation of zinc protoporphyrin (ZnPP), a natural pigment of great interest for the meat industry. The aim of this study was to analyse the effect of pork liver drying (from 10 to 70 degrees C), as a stabilisation method, on the FeCH activity (EA) and the apparent concentration (ECapp). Drying temperatures close to room conditions (from 10 to 20 degrees C) allowed to preserve well the ECapp, while the EA was slightly lower ( 15.2%) than in raw liver. However, when drying was conducted at extreme conditions ( 10 and 70 degrees C), the lowest values of ECapp and EA were manifested. Therefore, the drying process at moderate temperatures close to room conditions (10 - 20 degrees C) was considered to be an effective method for FeCH preservation since it was possible to stabilise the liver and the loss of FeCH activity was minimised., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad (MINECO)" and "Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Projects RTA2017-00024-C04-03 and RTA2017-00024-C04-01)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Physicochemical and Techno-Functional Properties of Dried and Defatted Porcine Liver

  • Abril-Gisbert, Blanca
  • Toldrà Alegret, Mònica
  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
[EN] Porcine liver has a high nutritional value and is rich in proteins, minerals, and vitamins, making it an interesting co-product to alleviate the growing global demand for protein. The objective of this study was to analyze how the drying and defatting processes of porcine liver affect the physicochemical and techno-functional properties of its proteins. Two drying temperatures (40 and 70 °C) were studied, and dried samples were defatted using organic solvents. The drying process turned out to be an effective method for the stabilization of the protein fraction; however, when the drying temperature was high (70 °C), greater protein degradation was found compared to drying at a moderate temperature (40 °C). Regarding the defatting stage, it contributed to an improvement in certain techno-functional properties of the liver proteins, such as the foaming capacity (the average of the dried and defatted samples was 397% higher than the dried samples), with the degree of foaming stability in the liver dried at 40 °C and defatted being the highest (13.76 min). Moreover, the emulsifying capacity of the different treatments was not found to vary significantly (p > 0.05). Therefore, the conditions of the drying and defatting processes conducted prior to the extraction of liver proteins must be properly adjusted to maximize the stability, quality, and techno-functional properties of the proteins., This research was financially supported by the "Ministerio de Economia y Competitividad (MINECO)" and the "Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Projects RTA2017-00024-C04-03 and RTA2017-00024-C04-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Use of air-coupled ultrasound for the non-invasive characterization of the textural properties of pork burger patties

  • Fernandez-Caballero-Fariñas, Maria Dolores
  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
  • Sanchez-Jimenez, Virginia|||0000-0002-2075-0664
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
[EN] This study tests the feasibility of air-coupled ultrasound for the characterization of the textural properties of pork burger patties. The samples were prepared by mixing lard at different percentages (0, 20, 40, 60 and 80%) with a commercial burger meat mixture. Through-transmission airborne ultrasound measurements (250 kHz) were carried out at 5 and 20 degrees C. Ultrasonic velocity at 5 degrees C increased exponentially with fat content (r = 0.99), varying from 1587 to 1668 m/s, whereas it remained fairly constant at 20 degrees C (1644 to 1624 m/s). Ultrasonic attenuation decreased with fat content following an exponential pattern (r = 0.83 at 5 degrees C; r = 0.93 at 20 degrees C) and ranged from 62.6 to 44.8 Np/m at 5 degrees C, and from 76.7 to 42.2 Np/m at 20 degrees C. Noticeable correlations were found between hardness and ultrasonic velocity (r = 0.89 at 5 degrees C), and between Total Relaxation Capacity and ultrasonic attenuation (r = 0.89 at 5 degrees C; r = 0.99 at 20 degrees C). Additionally, airborne ultrasound allowed an accurate (mean relative difference 2.3%) prediction of burger thickness., This work was supported by the Agencia Estatal de Investigacion in Spain (Project RTC-2017-6314-2 & RTA 2017-00024-C04-03). M.D. Farinas is grateful for her post-doctoral "Juan de la Cierva" fellowship (FJCI-2017-34,759) through the program funded by the Spanish Ministry of Science, Innovation and Universities.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Role of Enzymatic Reactions in Meat Processing and Use of Emerging Technologies for Process Intensification

  • Abril-Gisbert, Blanca
  • Bou, Ricard
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Meat processing involves different transformations in the animal muscle after slaughtering, which results in changes in tenderness, aroma and colour, determining the quality of the final meat product. Enzymatic glycolysis, proteolysis and lipolysis play a key role in the conversion of muscle into meat. The accurate control of enzymatic reactions in meat muscle is complicated due to the numerous influential factors, as well as its low reaction rate. Moreover, exogenous enzymes are also used in the meat industry to produce restructured products (transglutaminase), to obtain bioactive peptides (peptides with antioxidant, antihypertensive and gastrointestinal activity) and to promote meat tenderization (papain, bromelain, ficin, zingibain, cucumisin and actinidin). Emerging technologies, such as ultrasound (US), pulsed electric fields (PEF), moderate electric fields (MEF), high-pressure processing (HPP) or supercritical CO2 (SC-CO2), have been used to intensify enzymatic reactions in different food applications. This review aims to provide an overview of the enzymatic reactions taking place during the processing of meat products, how they could be intensified by using emerging technologies and envisage potential applications., This research was financially supported by the "Ministerio de Economia y Competitividad (MINECO)" and the "Instituto Nacional de Investigación y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Projects RTA2017-00024-C04-03 and RTA2017-00024-C04-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Use of ultrasound for the characterization and correction of textural defects in dry-cured ham

  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
[EN] Dry-cured ham is a product highly appreciated by consumers, nevertheless, there are a large number of manufacturing process-related parameters, as well as ham intrinsic factors, that compromise its final quality. One of the main problems in the quality of dry-cured ham is the appearance of textural defects, in particular, the development of pastiness. This defect is characterized by an excessive softness and loss of elastic behavior of the ham and when tasted, it provokes a feeling similar to the mouth-coating sensation produced by a flour-water paste during the mastication process. Pastiness also makes slicing difficult and promotes the adhesiveness between slices. Currently, the methods available to measure ham pastiness are time-consuming and destructive. For this reason, the seek of faster and non-destructive technologies capable of detecting pastiness is of great importance. In this sense, different technologies such as near infrared spectroscopy, X-rays or ultrasound, that have been previously tested for the nondestructive characterization of different meat products, could be of interest for the detection of ham pastiness. Different approaches, such as the use of high hydrostatic pressure (HHP) or the application of low-temperature long-time thermal treatments (LTLT) at the end of the ham manufacturing, have been previously addressed for the correction of pastiness in dry-cured ham. Notwithstanding, the high cost and the long time required for the HHP and LTLT treatments, respectively, highlights the need for moderate cost and faster alternatives. In this context, the main goals of this thesis were to determine the feasibility of using low intensity ultrasound to non-destructively detect the appearance of pastiness during ham manufacturing and to characterize the level of pastiness in the final product, as well as to explore the feasibility of mild ultrasonic assisted thermal treatments to correct this textural defect. To meet the goal of ham pastiness characterization and correction, a customized drycured ham manufacturing was designed and carried out in order to obtain hams with different levels of pastiness with no remarkable differences on the salt content. During ham manufacturing, the feasibility of using contact ultrasound to monitor the appearance of pastiness was addressed. The ultrasonic velocity was measured in the raw ham, at the end of the salting and post-salting stages, 3 times during the drying-maturation and once the manufacturing was finished. At the end of the manufacturing, the pastiness level (high, medium and no pasty) was also sensory evaluated by an expert panel. As the manufacturing progressed, a progressive increase in the ultrasonic velocity, from 1536 m/s in the raw ham to 1713 m/s in the final dry-cured ham, was found. Notwithstanding, the increase in the ultrasonic velocity was not related with the pastiness defect, probably because the ham texture changes linked to pastiness were masked by the great influence of the compositional changes (salt gain and moisture loss) on the ultrasonic velocity. Therefore, the ultrasonic velocity was not an effective parameter to detect the appearance of pastiness in hams during manufacturing, neither to classify them according to its pastiness level at the end of the manufacturing. Contact ultrasound was also used to monitor the compositional and textural changes taking place along the ham post-salting stage. For this purpose, another batch of hams was salted and post-salting times from 7 to 56 days were tested. During post-salting, the hams were weighted and the ultrasonic velocity was measured every 2 days. Each 7 post-salting days, the composition and the textural properties of a different ham were destructively analyzed. The ham weight loss during the post-salting stage was satisfactorily (r=0.95) described by the increase in the ultrasonic velocity. Moreover, the salt distribution and the moisture loss in the internal parts of the ham were satisfactorily related (r=0.93 and r=0.86, respectively) with the increase in the ultrasonic velocity. The variation in the ham hardness during post-salting was negligible and hence, the velocity increase was mainly attributed to the compositional changes, being barely affected by the changes in texture. The hams obtained after the customized manufacturing were sliced and the ultrasonic velocity and attenuation were measured on the Biceps femoris muscle with the aim of nondestructively finding out its pastiness level. Furthermore, in order to better analyze this textural defect, the composition, protein degradation, instrumental texture and microstructure of the hams were analyzed. Pasty samples presented the highest proteolysis index (38.7% compared to 33.1% for non-pasty hams), exhibited the more relevant structural degradation (merged myofibril structures and appearance of large gaps) and consequently, were the softest (5.4 N of hardness compared to 16.7 N for non-pasty hams) and presented the most intense viscous behavior (0.434 compared to 0.372 for non-pasty hams), although a high degree of experimental variability was found. The non-destructive assessment performed with ultrasound revealed that ultrasonic attenuation could be successfully applied for the grading of dry-cured ham slices according to its pastiness level. Thus, the greater the pastiness, the higher the ultrasonic attenuation, being the average attenuation coefficient for high, medium and no-pasty samples 48.2, 45.4 and 43.1 Np/m, respectively. Notwithstanding, the ultrasonic velocity was similar in all the ham samples, regardless its pastiness level. As observed in whole hams, the ultrasonic velocity was not a satisfactory parameter to detect pastiness in sliced ham, since the large influence of the composition on the ultrasonic velocity added to a similar salt and moisture content of the samples, regardless its pastiness level, led to a similar velocity for the different pastiness levels. Air-coupled ultrasonic techniques in both through-transmission and pulse-echo modes were developed for the characterization of dry-cured ham texture. The non-invasive nature of aircoupled ultrasound allows a contactless measurement, which makes easier its industrial implementation compared to conventional ultrasound techniques for high speed applications without material surface alteration and cross-contamination between food items. As for corrective actions of the texture defects in dry-cured ham, mild thermal treatments in two different heating media (water and air) were evaluated. Furthermore, the feasibility of intensifying these mild thermal treatments with the assistance of power ultrasound was considered. For that purpose, commercial vacuum-packed dry-cured ham slices were heated in a liquid medium, with and without ultrasonic assistance, at different temperatures (40, 45 and 50 ºC), measuring the temperature in the Biceps femoris and in the Semimembranosus muscles. Regarding the treatments in air, commercial vacuum-packed dry-cured ham cylinders were used. In the first set of experiments, ham was heated at a constant air velocity (2 m/s) until different temperatures (40, 45 and 50 ºC) were reached. While in the second set of experiments, ham was treated at constant air temperature (50 ºC) at different air velocities (1, 2, 3, 4 and 6 m/s). In both sets, the treatments were performed with and without power ultrasound application, measuring the temperature in the center of the cylinder. Thermal treatments were extended until a target temperature of 5 ºC lower than the medium (water-air) heating temperature was reached, thus, holding temperature stage did not exist and the treatments only considered the heating one. The heating kinetics of the ham treated in both water and air heating media were mathematically described by means of a heat conduction model. Once the heating finalized, the textural changes of ham (hardness and elastic behavior) were evaluated. The experiments showed that power ultrasound application sped up the heat transfer, significantly (p<0.05) shortening the heating time and increasing the apparent thermal diffusivity up to 51 and 37% for water and air heat treatments, respectively. For the thermal treatments using water, the increase in temperature during the heating brought about a lower ultrasonic intensification (the apparent thermal diffusivity was increased by 51% at 40 ºC compared to the 21% at 50 ºC). On the contrary, in experiments with air, the higher the temperature, the greater the ultrasonic enhancement (the apparent thermal diffusivity was increased by 5% at 40 ºC compared to the 38% at 50 ºC). The effect of the ultrasound application decreased as the air velocity increased, being minimal when the air velocity was the highest (the apparent thermal diffusivity was increased by 21% at 1 m/s compared to the 5% at 6 m/s). As regards the changes in the textural properties of ham after the mild thermal treatments at short times, an increase in hardness and elastic behavior was observed. Finally, the texture correction in dry-cured ham with different levels of pastiness was tackled. For this purpose, vacuum-packed dry-cured ham slices with high, medium and no pastiness were heated in a liquid medium at 40 and 50 ºC for a longer time (5 h, including heating and holding stages) than heating experiments, with and without the assistance of power ultrasound during the heating phase. The texture (hardness, elastic behavior and adhesiveness) and the microstructure of the ham was evaluated in both treated and control samples. After the mild thermal treatments, the texture of ham was improved since the hardness was increased (102%) and the viscous behavior diminished (11%). On average, the increase of hardness at 50 ºC was 159% higher than at 40 ºC, while the decrease of the viscous behavior was 13.5% larger at 50 ºC compared to 40 ºC. The ham adhesiveness was also enhanced independently of the treatment temperature, with a 55% reduction being observed. The application of power ultrasound during the heating phase did not involve any additional textural change. Likewise, after the thermal treatments, the microstructure of hams with pastiness notably changed, experiencing a severe shrinkage of the myofibrils, which contributed to explain the reported textural changes. In conclusion, pastiness is a relevant and highly complex textural defect in dry-cured ham. The use of contact ultrasound and the measurement of the ultrasonic attenuation could be considered a potential technology to non-destructively detect and characterize pastiness in sliced dry-cured ham. Future work should focus on extending this approach to identify pasty whole hams, considering for this purpose the use of air-coupled ultrasound. Moreover, the use of mild thermal treatments in liquid or gas media could be a feasible method to correct the defective texture of dry-cured hams and the application of power ultrasound during the heating phase could be a relevant means of speeding up the thermal treatments., [ES] El jamón curado es un producto muy apreciado por los consumidores, sin embargo, existen numerosos parámetros relacionados con el procesado, así como factores intrínsecos del jamón, que comprometen su calidad final. Uno de los principales problemas de calidad del jamón curado es la aparición de defectos de textura, concretamente, el desarrollo de pastosidad. Este defecto se caracteriza por una textura excesivamente blanda y un comportamiento menos elástico del jamón. A nivel sensorial, provoca una sensación de recubrimiento en boca similar a la masticación de una pasta de harina y agua. La pastosidad también dificulta el loncheado y promueve la adhesividad entre lonchas. Actualmente, los métodos disponibles para caracterizar la pastosidad requieren mucho tiempo y son destructivos. Por esta razón, la búsqueda de tecnologías más rápidas y no destructivas capaces de detectar la pastosidad es de gran importancia. En este sentido, distintas tecnologías como espectroscopía de infrarrojo cercano, rayos-X o ultrasonidos, que han sido ensayadas previamente para la caracterización no destructiva de diferentes productos cárnicos, podrían ser de interés para la detección de pastosidad en jamón. Diferentes alternativas, como el uso de altas presiones hidrostáticas (HHP) o la aplicación de tratamientos térmicos de larga duración a baja temperatura (LTLT) al final del proceso de elaboración del jamón, han sido abordadas previamente para la corrección de pastosidad en jamón curado. Sin embargo, el elevado coste y el largo tiempo requerido para los tratamientos HHP y LTLT, respectivamente, pone de manifiesto la necesidad de encontrar alternativas con un coste moderado y más rápidas. En este contexto, los principales objetivos de esta tesis fueron determinar la viabilidad de la utilización de ultrasonidos de baja intensidad para detectar de manera no destructiva la aparición de pastosidad durante el proceso de elaboración de jamón curado y caracterizar el nivel de pastosidad en el producto final, así como explorar la viabilidad de tratamientos térmicos moderados asistidos por ultrasonidos de alta intensidad para corregir dicho defecto de textura. Para cumplir el objetivo de caracterizar y corregir el defecto de pastosidad en jamón, se diseñó y se llevó a cabo un proceso de elaboración para obtener jamones con distintos niveles de pastosidad sin diferencias considerables del contenido en sal. Durante el procesado, se abordó la viabilidad de utilizar ultrasonidos por contacto para monitorizar la aparición de la pastosidad. Así, la velocidad ultrasónica se midió en el jamón fresco, al final de las etapas de salado y postsalado, 3 veces durante el secado-maduración y una vez terminado el proceso de elaboración. Al final del procesado, también se evaluó el nivel de pastosidad (alto, medio y sin pastosidad) en el jamón loncheado por un panel experto. A medida que avanzó el proceso de elaboración, se observó un aumento progresivo de la velocidad ultrasónica, de 1536 m/s en jamón fresco hasta 1713 m/s en jamón curado. Sin embargo, el aumento en la velocidad ultrasónica no se relacionó con el defecto de pastosidad, probablemente porque los cambios de textura del jamón vinculados con la pastosidad fueron enmascarados por la gran influencia de los cambios composicionales (ganancia de sal y pérdida de humedad) en la velocidad ultrasónica. Así, la velocidad ultrasónica no fue un parámetro útil para detectar la aparición de pastosidad en jamón durante su procesado ni para clasificar los jamones según su nivel de pastosidad al final del procesado. Los ultrasonidos por contacto también se utilizaron para monitorizar los cambios composicionales y texturales que tienen lugar a lo largo de la etapa de postsalado del jamón. Para ello, se saló otro lote de jamones y se evaluaron distintos tiempos de postsalado, desde 7 hasta 56 días. Durante el postsalado, los jamones se pesaron y se midió su velocidad ultrasónica cada 2 días. Cada 7 días de postsalado, se analizó destructivamente la composición y las propiedades texturales de un jamón. La pérdida de peso de los jamones durante la etapa de postsalado fue descrita satisfactoriamente (r=0.95) por el aumento de la velocidad ultrasónica. Además, la distribución de sal y la pérdida de humedad en el interior del jamón se relacionaron de forma satisfactoria (r=0.93 y r=0.86, respectivamente) con el aumento de la velocidad ultrasónica. La variación en la dureza del jamón durante el postsalado fue no significativa y, por ello, el aumento de la velocidad ultrasónica se atribuyó principalmente a los cambios de composición, siendo apenas afectada por los cambios de textura. Los jamones obtenidos con distintos niveles de pastosidad después del proceso de elaboración, se cortaron y se midió la velocidad y la atenuación ultrasónica del músculo Biceps femoris con el objetivo de averiguar de forma no destructiva su nivel de pastosidad. Además, con el fin de analizar mejor este defecto de textura, se analizaron el índice de proteólisis, la microestructura, la textura instrumental y la composición de los jamones. Las muestras pastosas presentaron el índice de proteólisis más alto (38.7% comparado con el 33.1% de los jamones no pastosos), mostraron la degradación estructural más relevante (estructuras miofibrilares fusionadas y aparición de grandes huecos) y, en consecuencia, fueron las más blandas (5.4 N de dureza en comparación con los 16.7 N de los jamones no pastosos) y presentaron el comportamiento viscoso más intenso (0.434 comparado con el 0.372 de los jamones no pastosos), aunque se encontró una gran variabilidad experimental. La evaluación no destructiva llevada a cabo mediante ultrasonidos reveló que la atenuación ultrasónica se podría aplicar con éxito para la clasificación de las lonchas de jamón curado según su nivel de pastosidad. Así, cuanto mayor fue la pastosidad, mayor fue la atenuación ultrasónica, siendo el coeficiente de atenuación promedio de las muestras con alta, media y sin pastosidad de 48.2, 45.4 y 43.1 Np/m, respectivamente. Sin embargo, la velocidad ultrasónica fue muy similar en todas las muestras de jamón, independientemente de su nivel de pastosidad. Como se observó en los jamones enteros, la velocidad ultrasónica no fue un parámetro útil para cuantificar el defecto de pastosidad en jamón loncheado, ya que la gran influencia de la composición en la velocidad ultrasónica sumada al contenido similar de sal y humedad de las muestras, independientemente de su nivel de pastosidad, dio lugar a una velocidad similar en todos los niveles de pastosidad. Se desarrollaron dos técnicas de ultrasonidos acoplados por aire, tanto en modo transmisión-recepción como en pulso-eco, para caracterizar la textura de jamón curado. El carácter no invasivo de los ultrasonidos acoplados por aire permite llevar a cabo medidas sin contacto, facilitando su aplicación a nivel industrial en comparación con las técnicas ultrasónicas convencionales, ya que pueden realizarse medidas a mayor velocidad, sin alterar la superficie del material y evitando la contaminación cruzada entre alimentos. En cuanto a las medidas de corrección de defectos texturales en jamón curado, se evaluaron tratamientos térmicos moderados en dos medios de calentamiento diferentes (agua y aire). Además, se consideró la viabilidad de intensificar dichos tratamientos mediante la aplicación de ultrasonidos de alta intensidad (o de potencia). Para ello, se calentaron lonchas de jamón curado comercial envasadas al vacío en medio líquido, con y sin la aplicación de ultrasonidos, a diferentes temperaturas (40, 45 y 50 ºC), midiendo la temperatura en los músculos Biceps femoris y Semimembranosus. Respecto a los tratamientos en aire, se utilizaron cilindros de jamón curado comercial envasado al vacío. En el primer set de experimentos, el jamón se calentó a velocidad de aire constante (2 m/s) a diferentes temperaturas (40, 45 y 50 ºC); mientras que, en el segundo experimento, el jamón se calentó a temperatura de aire constante (50 ºC) a distintas velocidades (1, 2, 3, 4 y 6 m/s). En los dos sets, los tratamientos se llevaron a cabo con y sin la aplicación de ultrasonidos de potencia, midiendo la temperatura en el centro del cilindro. Los tratamientos térmicos se prolongaron hasta alcanzar la temperatura objetivo, definida como 5 ºC por debajo de la temperatura del medio de calentamiento (agua o aire). Así, no se llevó a cabo una fase de mantenimiento de la temperatura y sólo se consideró la fase de calentamiento de los tratamientos térmicos. Las cinéticas de calentamiento del jamón tratado tanto en agua como en aire se describieron matemáticamente considerando que la transferencia de calor estuvo únicamente controlada por conducción. Una vez finalizado el calentamiento, se evaluaron los cambios texturales del jamón (dureza y comportamiento elástico). Los experimentos mostraron que la aplicación de ultrasonidos de potencia aceleró la transferencia de calor, reduciendo significativamente (p<0.05) el tiempo de calentamiento y aumentando la difusividad térmica aparente hasta un 51 y 37% en los tratamientos térmicos en agua y aire, respectivamente. En el caso de los tratamientos térmicos en agua, el aumento de la temperatura durante el calentamiento provocó una intensificación ultrasónica menor (la difusividad térmica aparente aumentó un 51% a 40 ºC comparado con el 21% a 50 ºC). Por el contrario, en las experiencias en aire, cuanto mayor fue la temperatura, más efectiva fue la aplicación de los ultrasonidos (la difusividad térmica aparente incrementó un 5% a 40 ºC comparado con el 38% a 50 ºC). El efecto de la aplicación de los ultrasonidos disminuyó con el aumento de la velocidad del aire, siendo mínimo con la velocidad de aire más alta ensayada (la difusividad térmica aparente aumentó un 21% a 1 m/s comparado con el 5% a 6 m/s). En cuanto a los cambios de las propiedades texturales del jamón después de los tratamientos térmicos moderados limitados a la fase de calentamiento, se observó un aumento en su dureza y en su comportamiento elástico. Por último, se abordó la corrección de textura en jamón curado con distintos niveles de pastosidad. Para ello, se calentaron lonchas de jamón con alta, media y sin pastosidad envasadas al vacío en medio líquido a 40 y 50 ºC durante tiempos más largos (5 h, incluyendo las fases de calentamiento y mantenimiento) que en las experiencias sólo de calentamiento, con y sin la aplicación de ultrasonidos de potencia únicamente durante la fase de calentamiento. La textura (dureza, comportamiento elástico y adhesividad) y la microestructura del jamón se evaluaron tanto en las muestras tratadas como en las control. Después de los tratamientos térmicos moderados, la textura del jamón se vio mejorada puesto que su dureza aumentó (102%) y su comportamiento viscoso disminuyó (11%). En promedio, el aumento de la dureza a 50 ºC fue un 159% mayor que a 40 ºC, mientras que la disminución del comportamiento viscoso fue un 13.5% mayor a 50 ºC que a 40 ºC. La adhesividad del jamón también se vio disminuida, independientemente de la temperatura de tratamiento, observándose una reducción media del 55%. La aplicación de ultrasonidos de potencia durante la fase de calentamiento no implicó ningún cambio textural adicional. Asimismo, después de los tratamientos térmicos, la microestructura de los jamones con alta pastosidad cambió notablemente, experimentando una severa contracción de las miofibrillas, lo cual contribuyó a explicar los cambios de textura mencionados. En conclusión, la pastosidad es un defecto textural relevante y muy complejo en jamón curado. El uso de ultrasonidos por contacto y la medida de la atenuación ultrasónica podría considerarse a nivel industrial para detectar y caracterizar de forma no destructiva la pastosidad en lonchas de jamón curado. Futuros trabajos deberían estar orientados a la aplicación de esta tecnología para la identificación de jamones pastosos enteros, considerando para ello el uso de ultrasonidos acoplados por aire. Además, el uso de tratamientos térmicos moderados en medio líquido o gaseoso podría ser un método viable para corregir la textura defectuosa de jamones curados y la aplicación de ultrasonidos de potencia durante la fase de calentamiento podría considerarse para acelerar los tratamientos térmicos., [CA] El pernil curat és un producte molt apreciat pels consumidors, no obstant això, existeixen nombrosos paràmetres relacionats amb el processament, així com factors intrínsecs del pernil, que comprometen la seua qualitat final. Un dels principals problemes de qualitat del pernil curat és l'aparició de defectes de textura, concretament, el desenvolupament de pastositat. Aquest defecte es caracteritza per una excessiva blanor i una pèrdua del comportament elàstic del pernil. A nivell sensorial, provoca una sensació de recobriment en boca similar a la masticació d'una pasta de farina i aigua. La pastositat també dificulta el tallat i promou l'adhesivitat entre rodanxes. Actualment, els mètodes disponibles per a mesurar la pastositat requereixen molt de temps i són destructius. Per aquesta raó, la cerca de tecnologies més ràpides i no destructives capaces de detectar la pastositat és de gran importància. En aquest sentit, diferents tecnologies com espectroscòpia d'infraroig pròxim, raigs-X o ultrasons, que han sigut assajades prèviament per a la caracterització no destructiva de diferents productes carnis, podrien ser d'interés per a la detecció de pastositat en pernil. Diferents alternatives, com l'ús d'altes pressions hidroestàtiques (HHP) o l'aplicació de tractaments tèrmics de llarga duració a baixa temperatura (LTLT) al final del procés d'elaboració del pernil, han sigut abordades prèviament per a la correcció de pastositat en pernil curat. No obstant això, l'elevat cost i el llarg temps requerit per als tractaments HHP i LTLT, respectivament, posa de manifest la necessitat de trobar alternatives amb un cost moderat i més ràpides. En aquest context, els principals objectius d'aquesta tesi van ser determinar la viabilitat de la utilització dels ultrasons de baixa intensità per a detectar de manera no destructiva l'aparició de pastositat durant el procés d’elaboració de pernil curat i caracteritzar el nivell de pastositat en el producte final, així com explorar la viabilitat de tractaments tèrmics moderats assistits per ultrasons d’alta intensitat per a corregir aquest defecte de textura. Per a complir l'objectiu de caracteritzar i corregir el defecte de pastositat en pernil, es va dissenyar i es va dur a terme un procés d'elaboració configurat per a obtindre pernils amb diferents nivells de pastositat sense diferències considerables del contingut en sal. Durant el processament, es va abordar la viabilitat d'utilitzar ultrasons per contacte per a monitorar l'aparició de pastositat. La velocitat ultrasònica es va mesurar en el pernil fresc, al final de les etapes de salat i postsalat, 3 vegades durant l'assecat-maduració i una vegada acabat el procés d'elaboració. Al final del processament, el nivell de pastositat (alta, mitjana i sense pastositat) també es va avaluar per un panell expert. A mesura que va avançar el procés d'elaboració, es va trobar un augment progressiu de la velocitat ultrasònica, anant des de 1536 m/s en pernil fresc fins a 1713 m/s en pernil curat. No obstant això, l'augment en la velocitat ultrasònica no es va relacionar amb el defecte de pastositat, probablement perquè els canvis de textura del pernil vinculats amb la pastositat van ser emmascarats per la gran influència dels canvis composicionals (guany de sal i pèrdua d'humitat) en la velocitat ultrasònica. Així, la velocitat ultrasònica no va ser un paràmetre efectiu per a detectar l'aparició de pastositat en pernil durant el seu processament ni per a classificar els pernils segons el seu nivell de pastositat al final del processament. Els ultrasons per contacte també es van utilitzar per a monitorar els canvis composicionals i texturals que tenen lloc al llarg de l'etapa de postsalat del pernil. Per a això, es va salar un altre lot de pernils i es van avaluar diferents temps de postsalat, des de 7 fins a 56 dies. Durant el postsalat, els pernils es van pesar i es va mesurar la seua velocitat ultrasònica cada 2 dies. Cada 7 dies de postsalat, es van analitzar destructivament la composició i les propietats texturals d'un pernil diferent. La pèrdua de pes dels pernils durant l'etapa de postsalat va ser descrita satisfactòriament (r=0.95) per l'augment de la velocitat ultrasònica. A més, la distribució de sal i la pèrdua d'humitat a l'interior del pernil es van relacionar de manera satisfactòria (r=0.93 i r=0.86, respectivament) amb l'augment de la velocitat ultrasònica. La variació en la duresa del pernil durant el postsalat va ser mínima i, per això, l'augment de la velocitat ultrasònica es va atribuir principalment als canvis de composició, sent a penes afectada pels canvis de textura. Els pernils obtinguts després del procés d'elaboració configurat per a obtindre pernils amb diferents nivells de pastositat, es van tallar i es va mesurar la velocitat i l'atenuació ultrasònica del múscul Biceps femoris amb l'objectiu d'esbrinar de forma no destructiva el seu nivell de pastositat. A més, amb la finalitat d'analitzar millor aquest defecte de textura, es van analitzar la composició, la degradació proteica, la textura instrumental i la microestructura dels pernils. Les mostres pastoses van presentar l'índex de proteòlisis més alt (38.7% comparat amb el 33.1% dels pernils no pastosos), van mostrar la degradació estructural més rellevant (estructures miofibrilars fusionades i aparició de grans buits) i, en conseqüència, van ser les més blanes (5.4 N de duresa en comparació amb els 16.7 N dels pernils no pastosos) i van presentar el comportament viscós més intens (0.434 comparat amb el 0.372 dels pernils no pastosos), encara que es va trobar una gran variabilitat experimental. L'avaluació no destructiva duta a terme mitjançant ultrasons va revelar que l'atenuació ultrasònica es podria aplicar amb èxit per a la classificació de les rodanxes de pernil curat segons el seu nivell de pastositat. Així, com més gran va ser la pastositat, major va ser l'atenuació ultrasònica, sent el coeficient d'atenuació mitjà de les mostres amb alta, mitjana i sense pastositat 48.2, 45.4 i 43.1 Np/m, respectivament. No obstant això, la velocitat ultrasònica va ser molt similar en totes les mostres de pernil, independentment del seu nivell de pastositat. Com es va observar en els pernils sencers, la velocitat ultrasònica no va ser un paràmetre satisfactori per a detectar el defecte de pastositat en pernil tallat a rodanxes, ja que la gran influència de la composició en la velocitat ultrasònica sumada al contingut similar de sal i humitat de les mostres, independentment del seu nivell de pastositat, va donar lloc a una velocitat similar en tots els nivells de pastositat. Es van desenvolupar dues tècniques d'ultrasons acoblats per aire, tant en manera transmissió-recepció com en pols-eco, per a caracteritzar la textura de pernil curat. El caràcter no invasiu dels ultrasons acoblats per aire permet dur a terme mesures sense contacte, facilitant la seua aplicació a nivell industrial en comparació amb les tècniques ultrasòniques convencionals, ja que poden realitzar-se mesures a major velocitat, sense alterar la superfície del material i evitant la contaminació creuada entre aliments. Quant a les mesures de correcció de defectes texturals en pernil curat, es van avaluar tractaments tèrmics moderats en dos medis de calfament diferents (aigua i aire). A més, es va considerar la viabilitat d'intensificar aquests tractaments mitjançant l'aplicació d'ultrasons de potència. Per a això, es van calfar rodanxes de pernil curat comercial envasades al buit en medi líquid, amb i sense l'aplicació d'ultrasons, a diferents temperatures (40, 45 i 50 °C), mesurant la temperatura en els músculs Biceps femoris i Semimembranosus. Respecte als tractaments en aire, es van utilitzar cilindres de pernil curat comercial envasat al buit. En el primer set d'experiments, el pernil es va calfar a velocitat d'aire constant (2 m/s) fins que es van aconseguir diferents temperatures (40, 45 i 50 °C). Mentre que, en el segon, el pernil es va calfar a temperatura d'aire constant (50 °C) a diferents velocitats (1, 2, 3, 4 i 6 m/s). En els dos sets, els tractaments es van dur a terme amb i sense l'aplicació d'ultrasons de potència, mesurant la temperatura en el centre del cilindre. Els tractaments tèrmics es van prolongar fins a aconseguir la temperatura objectiu, definida 5 °C per davall de la temperatura del medi de calfament (aigua o aire); així, no es va dur a terme una fase de manteniment de la temperatura i només es va considerar la fase de calfament dels tractaments tèrmics. Les cinètiques de calfament del pernil tractat tant en aigua com en aire es van descriure matemàticament mitjançant un model de conducció de calor. Una vegada finalitzat el calfament, es van avaluar els canvis texturals del pernil (duresa i comportament elàstic). Els experiments van mostrar que l'aplicació d'ultrasons de potència va accelerar la transferència de calor, reduint significativament (p<0.05) el temps de calfament i augmentant la difusivitat tèrmica aparent fins a un 51 i 37% en els tractaments tèrmics en aigua i aire, respectivament. En el cas dels tractaments tèrmics en aigua, l'augment de la temperatura durant el calfament va provocar una intensificació ultrasònica menor (la difusivitat tèrmica aparent va augmentar un 51% a 40 °C comparat amb el 21% a 50 °C). Per contra, en les experiències en aire, com més alta va ser la temperatura, més efectiva va ser l'aplicació dels ultrasons (la difusivitat tèrmica aparent va incrementar un 5% a 40 °C comparat amb el 38% a 50 °C). L'efecte de l'aplicació dels ultrasons va disminuir amb l'augment de la velocitat de l'aire, sent mínim amb la velocitat d'aire més alta assajada (la difusivitat tèrmica aparent va augmentar un 21% a 1 m/s comparat amb el 5% a 6 m/s). Quant als canvis de les propietats texturals del pernil després dels tractaments tèrmics moderats a temps curts, es va observar un augment en la seua duresa i en el seu comportament elàstic. Finalment, es va abordar la correcció de textura en pernil curat amb diferents nivells de pastositat. Per a això, es van calfar rodanxes de pernil amb alta, mitjana i sense pastositat envasades al buit en medi líquid a 40 i 50 °C durant temps més llargs (5 h, incloent les fases de calfament i manteniment) que en les experiències només de calfament, amb i sense l'aplicació d'ultrasons de potència durant la fase de calfament. La textura (duresa, comportament elàstic i adhesivitat) i la microestructura del pernil es van avaluar tant en les mostres tractades com en les control. Després dels tractaments tèrmics moderats, la textura del pernil es va veure millorada perquè la seua duresa va augmentar (102%) i el seu comportament viscós va disminuir (11%). En mitjana, l'augment de la duresa a 50 °C va ser un 159% major que a 40 °C, mentre que la disminució del comportament viscós va ser un 13.5% major a 50 °C que a 40 °C. L'adhesivitat del pernil també es va veure disminuïda, independentment de la temperatura de tractament, observant-se una reducció del 55%. L'aplicació d'ultrasons de potència durant la fase de calfament no va implicar cap canvi textural addicional. Així mateix, després dels tractaments tèrmics, la microestructura dels pernils amb alta pastositat va canviar notablement, experimentant una severa contracció de les miofibrilles, el que va contribuir a explicar els canvis de textura esmentats. En conclusió, la pastositat és un defecte de textura rellevant i molt complex en pernil curat. L'ús d'ultrasons per contacte i la mesura de l'atenuació ultrasònica podria considerar-se una tecnologia potencial per a detectar i caracteritzar de forma no destructiva la pastositat en rodanxes de pernil curat. Futurs treballs haurien d'estar orientats a l'aplicació d'aquesta tecnologia per a la identificació de pernils pastosos sencers, considerant per a això l'ús d'ultrasons acoblats per aire. A més, l'ús de tractaments tèrmics moderats en medi líquid o gasós podria ser un mètode viable per a corregir la textura defectuosa de pernils curats i l'aplicació d'ultrasons de potència durant la fase de calfament podria ser una forma rellevant d'accelerar els tractaments tèrmics., Gracias a la Universitat Politècnica de València por concederme la beca para realizar mis estudios de doctorado, así como a los proyectos de investigación en los que he participado (RTA2013-00030-C03-02 y RTA2017-00024-C04-03)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of air velocity on airborne ultrasound application in pork liver drying

  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Giacomozzi, Anabella Soledad|||0000-0002-6528-3000
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Bon Corbín, José|||0000-0002-0457-9705
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Dalmau-Estelrich, Maria Esperanza
[EN] Airborne ultrasound is considered a feasible emerging technology for the intensification of the drying of biological materials due to its mild thermal effect avoiding the degradation of heat sensitive compounds. The effects brought about by airborne ultrasound on the drying are largely dependent on both the product structure itself and the process variables used. Thus, the present study examines the effect of the air velocity and the application of airborne ultrasound during the low-temperature convective drying of pork liver. For this purpose, drying experiments were carried out at 50 ¿ 6 m¿s 1 , C on pork liver cylinders using different air velocities, ranging from 1 to without (AIR) and with ultrasound application (US). The modelling of the drying kinetics was approached using the diffusion theory, evaluating both the contribution of external convection and shrinkage. The experimental results demonstrated that the application of airborne ultrasound only increased the drying rate at air velocities below 3 m¿s 1 , shortening the drying time by up to 30 %., The authors acknowledge the financial support from the Ministerio de Economía y Competitividad (MINECO) and Instituto Nacional de Investigaci¿ on y Tecnología Agraria y Alimentaria (INIA) in Spain (Project RTA2017-00024-C04-03). Eduardo A. Sanchez-Torres acknowledges the FPU PhD contract (FPU18/01439) granted by the Spanish Ministry of Science, Innovation and Universities. E. Dalmau acknowledges the Margarita Salas contract from the Universitat de les Illes Balears. Funding for open access charge: Universitat Polit` ecnica de Val` encia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Supercritical CO2 deodorization of dried pork liver

  • Abril-Gisbert, Blanca
  • Lorenzo, J.M.
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Pork liver has excellent nutritional properties but is a highly perishable product often rejected by consumers due to its strong unpleasant flavour. The objective of this study was to analyze the feasibility of the deodorization , defatting of dried pork liver by means of supercritical CO2 (SC-CO2) and conventional vacuum steam distillation (VSD).The results showed that both deodorization techniques were effective at reducing volatile organic compounds (VOCs). Through VSD, the VOC content was reduced by 67.6% UA, while an 81.3% UA reduction was achieved by SC-CO2, with respect to dried pork liver. In addition, 3 characteristic compounds of raw pork liver were completely eliminated by applying SC-CO2, which could potentially reduce the characteristic mushroom (1-octen-3-ol), fatty and green (1-nonanol) , fishy ((E,E)- 2,4-heptadienal) off-flavours. Therefore, SC-CO2 could be considered a promising technique for the elimination of VOCs, and furthermore it leads to a reduction in the fat content (24.9%)., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad (MINECO) and Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Project RTA2017-00024-C04-03). The authors acknowledge the contribution of the slaughterhouse "Carnes de Teruel S.A.", (D.O. Jamon de Teruel, Spain) for the supply of pork livers.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Water desorption isotherms of pork liver and thermodynamic properties

  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Bon Corbín, José|||0000-0002-0457-9705
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Abril-Gisbert, Blanca
[EN] For the first time, the relationship between equilibrium moisture content and water activity is reported for the desorption process in pork liver. For that purpose, a standardized conductivity hygrometer was used at four different temperatures (0, 10, 30 and 50 degrees C) over a wide range of water activity (0.999-0.103). Five models frequently found in the literature (GAB, Oswin, Henderson, Hasley and Ratti) were considered for the purposes of describing the experimental desorption. The GAB model emerged as the best option (explained variance 96.6%) for the physical and mathematical description of the water desorption isotherms in pork liver. The computed isosteric heat, entropy and Gibbs energy illustrated the high water-sorbent affinity, because of a considerable availability of strong sorption sites at low moisture contents. The reported experimental desorption isotherms, and modeling results, are essentials for the optimal design of the drying process of pork liver, which is a necessary step for the further research addressing the extraction of the protein fraction from the dried product. Extraction and isolation of the protein fraction from pork liver could be considered a reasonable strategy considering the demand of protein materials and the high-environmental impact of the meat industry., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad (MINECO)" and "Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Project RTA 2017-00024-C04-03). Eduardo A. Sanchez-Torres acknowledges the FPU PhD contract (FPU18/01439) granted by the Spanish Ministry of Science, Innovation and Universities.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the induced mild heating by airborne ultrasound application on the convective drying of pork liver

  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Giacomozzi, Anabella Soledad|||0000-0002-6528-3000
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Bon Corbín, José|||0000-0002-0457-9705
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Abril-Gisbert, Blanca
[EN] Efcient use of meat by-products, such as pork liver, may entail a previous stage of dehydration for their stabilization, which involves signifcant energy and time investments. Airborne ultrasound application has been reported as a promising technique to accelerate the air drying of food materials. In this context, the present study addresses, for the frst time, the thermal efect associated with ultrasound application on a meat by-product. For that purpose, drying experiments were conducted at 40 and 60 °C on pork liver cylinders at 2 m¿s ¿1 with (US) and without (AIR) airborne ultrasound application. The modeling process was based on the principles of heat conduction and moisture difusion, taking into account the external convection. The results showed that the use of ultrasound reduced the drying time by around 30% at 40 °C, although its impact was less pronounced at 60 °C. With the application of ultrasound, both the sample and air fow temperatures rose by about 4.5 and 2.5 °C, respectively, which partly explains the improvement of drying rate. Due to this low heating efect, airborne ultrasound application must be considered a non-thermal intensifcation strategy for convective drying of pork liver., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The authors express their gratitude for the fnancial support provided by the Ministerio de Economía y Competitividad (MINECO) and the Instituto Nacional de Investigación y Tecnología Agraria y Alimentaria (INIA) in Spain (Project RTA2017-00024-C04-03). Eduardo A. Sanchez-Torres acknowledges the FPU PhD contract (FPU18/01439) awarded by the Ministerio de Ciencia, Innovación y Universidades in Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasound intensification of Ferrochelatase extraction from pork liver as a strategy to improve ZINC-protoporphyrin formation

  • Abril-Gisbert, Blanca
  • Bou, R.
  • Sanchez-Torres, E.A.|||0000-0003-4121-2459
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] The enzyme Ferrochelatase (FeCH), which is naturally present in pork liver, catalyses the formation of Zincprotoporphyrin (ZnPP), a natural pigment responsible for the typical color of dry-cured Italian Parma ham. The aim of this study was to evaluate the feasibility of using high power ultrasound in continuous and pulsed modes to intensify the extraction of the enzyme FeCH from pork liver. US application during FeCH extraction led to an improved enzymatic activity and further increase in the formation of ZnPP. The optimal condition tested was that of 1 min in continuous US application, in which time the enzymatic activity increased by 33.3 % compared to conventional extraction (30 min). Pulsed US application required 5 min treatments to observe a significant intensification effect. Therefore, ultrasound is a potentially feasible technique as it increases the catalytic activity of FeCH and saves time compared to the conventional extraction method, The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad (MINECO) and Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain (Project RTA2017-00024-C04-03). The authors acknowledge the contribution of the undergraduate student Jose V. Pedrero-Gonzalez to the experimental work.
IRTA Pubpro. Open Digital Archive
Publicación Artículo científico (JournalArticle)

Ultrasound intensification of Ferrochelatase extraction from pork liver as a strategy to improve ZINC-protoporphyrin formation

  • Abril, B.
  • Sanchez-Torres, E.A.
  • Bou, R.
  • Garcia-Perez, J.V.
  • Benedito, J.
The enzyme Ferrochelatase (FeCH), which is naturally present in pork liver, catalyses the formation of Zinc-protoporphyrin (ZnPP), a natural pigment responsible for the typical color of dry-cured Italian Parma ham. The aim of this study was to evaluate the feasibility of using high power ultrasound in continuous and pulsed modes to intensify the extraction of the enzyme FeCH from pork liver. US application during FeCH extraction led to an improved enzymatic activity and further increase in the formation of ZnPP. The optimal condition tested was that of 1 min in continuous US application, in which time the enzymatic activity increased by 33.3 % compared to conventional extraction (30 min). Pulsed US application required 5 min treatments to observe a significant intensification effect. Therefore, ultrasound is a potentially feasible technique as it increases the catalytic activity of FeCH and saves time compared to the conventional extraction method., info:eu-repo/semantics/publishedVersion
IRTA Pubpro. Open Digital Archive
Publicación Artículo científico (JournalArticle)

Influence of pork liver drying on ferrochelatase activity for zinc protoporphyrin formation

  • Abril, B.
  • Sanchez-Torres, E.A.
  • Bou, Ricard
  • Benedito, J.
  • Garcia-Perez, Jose V.
Pork liver contains an endogenous enzyme, ferrochelatase (FeCH), which catalyses the formation of zinc protoporphyrin (ZnPP), a natural pigment of great interest for the meat industry. The aim of this study was to analyse the effect of pork liver drying (from −10 to 70 °C), as a stabilisation method, on the FeCH activity (EA) and the apparent concentration (ECapp). Drying temperatures close to room conditions (from 10 to 20 °C) allowed to preserve well the ECapp, while the EA was slightly lower (−15.2%) than in raw liver. However, when drying was conducted at extreme conditions (−10 and 70 °C), the lowest values of ECapp and EA were manifested. Therefore, the drying process at moderate temperatures close to room conditions (10 - 20 °C) was considered to be an effective method for FeCH preservation since it was possible to stabilise the liver and the loss of FeCH activity was minimised., info:eu-repo/semantics/publishedVersion
IRTA Pubpro. Open Digital Archive
Publicación Artículo científico (JournalArticle)

Role of Enzymatic Reactions in Meat Processing and Use of Emerging Technologies for Process Intensification

  • Abril, Blanca
  • Bou, Ricard
  • García-Pérez, Jose V.
  • Benedito, Jose
Meat processing involves different transformations in the animal muscle after slaughtering, which results in changes in tenderness, aroma and colour, determining the quality of the final meat product. Enzymatic glycolysis, proteolysis and lipolysis play a key role in the conversion of muscle into meat. The accurate control of enzymatic reactions in meat muscle is complicated due to the numerous influential factors, as well as its low reaction rate. Moreover, exogenous enzymes are also used in the meat industry to produce restructured products (transglutaminase), to obtain bioactive peptides (peptides with antioxidant, antihypertensive and gastrointestinal activity) and to promote meat tenderization (papain, bromelain, ficin, zingibain, cucumisin and actinidin). Emerging technologies, such as ultrasound (US), pulsed electric fields (PEF), moderate electric fields (MEF), high-pressure processing (HPP) or supercritical CO2 (SC-CO2), have been used to intensify enzymatic reactions in different food applications. This review aims to provide an overview of the enzymatic reactions taking place during the processing of meat products, how they could be intensified by using emerging technologies and envisage potential applications., This research was financially supported by the “Ministerio de Economía y Competitividad (MINECO)” and the “Instituto Nacional de Investigación y Tecnología Agraria y Alimentaria (INIA)” in Spain (Projects RTA2017-00024-C04-03 and RTA2017-00024-C04-02)., info:eu-repo/semantics/publishedVersion
IRTA Pubpro. Open Digital Archive
Publicación Artículo científico (JournalArticle)

Influence of ultrasonic application on the enzymatic formation of zinc protoporphyrin

  • Abril, B.
  • Contreras, M.
  • Bou, Ricard
  • Llauger, Mar
  • García-Pérez, J.V.
  • Benedito, J.
Ferrochelatase (FeCH), present in pork liver, catalyses the formation of zinc-protoporphyrin (ZnPP), a stable purple-red pigment found in Parma ham. Kinetics of ZnPP formation is especially slow. Thus, the aim of this study was to improve the ZnPP production using power ultrasound (US) at low (7.05 W/L) and moderate power (36.53 W/L) in homogenised pork liver (HLi) and with added oxyhemoglobin (HLi + OxyHb). ZnPP formation was performed at 37 °C, under anaerobic conditions, for different reaction times (6–48 h). When US was applied at low power, it shortened the time needed to reach maximum ZnPP formation by 50% and increased the yield by 25.77% in the case of HLi and by 4.42% in that of HLi + OxyHb, when compared to the control experiments; however, for the moderate power, ZnPP formation was hindered. Therefore, low power US proved to be an effective method with which to intensify enzymatic ZnPP production., info:eu-repo/semantics/publishedVersion
IRTA Pubpro. Open Digital Archive
Publicación Artículo científico (JournalArticle)

Strategies for porcine liver valorization as a source of food ingredients

  • Saguer, Elena
  • Abril, Blanca
  • Pateiro, Mirian
  • Bermúdez, Roberto
  • Domínguez-Valencia, Rubén
  • BOU, RICARD
Purpose of Review The sustainable consumption and production goal and the decline of offal consumption have led to the interest in seeking alternatives for porcine livers, the largest edible gland. To that aim, we reviewed the potential of porcine livers as a source of food ingredients together with the use of eco-innovative processes and technologies for their valorization. Recent Findings It is possible to extract and transform various compounds and fractions into food ingredients with tailored techno-functional properties using eco-innovative strategies involving microbial, enzymatic, physical, and chemical processes. These strategies can also contribute to improving the efficacy of different extraction and transformation processes as well as enhance sensory properties. Summary Porcine liver is an interesting source of valuable compounds with multiple food applications and health benefits. Through extraction, processing, and transformation, these compounds can yield versatile food ingredients, thereby optimizing the profitability of this resource for human consumption through alternative presentations and potentially diminishing consumer reluctance compared to the whole liver, This work was funded by the Spanish Ministerio de Ciencia e Innovación and the Agencia Estatal de Investigación [10.13039/501100011033], grant numbers RTA2017-00024 (coordinated projects C01 to C04) and PDC2021-121822 (coordinated projects C21-C22), and by the “European Union NextGenerationEU/PRTR”. We thank the Consolidated Research Group (2021 SGR00468) and CERCA Program from the Generalitat de Catalunya., info:eu-repo/semantics/publishedVersion
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Use of air-coupled ultrasound for the non-invasive characterization of the textural properties of pork burger patties

  • Fariñas, María Dolores
  • Contreras, Marina
  • Sánchez-Jiménez, Virginia
  • Benedito, José
  • García-Pérez, José V.
This study tests the feasibility of air-coupled ultrasound for the characterization of the textural properties of pork burger patties. The samples were prepared by mixing lard at different percentages (0, 20, 40, 60 and 80%) with a commercial burger meat mixture. Through-transmission airborne ultrasound measurements (250 kHz) were carried out at 5 and 20 °C. Ultrasonic velocity at 5 °C increased exponentially with fat content (r = 0.99), varying from 1587 to 1668 m/s, whereas it remained fairly constant at 20 °C (1644 to 1624 m/s). Ultrasonic attenuation decreased with fat content following an exponential pattern (r = −0.83 at 5 °C; r = −0.93 at 20 °C) and ranged from 62.6 to 44.8 Np/m at 5 °C, and from 76.7 to 42.2 Np/m at 20 °C. Noticeable correlations were found between hardness and ultrasonic velocity (r = 0.89 at 5 °C), and between Total Relaxation Capacity and ultrasonic attenuation (r = 0.89 at 5 °C; r = 0.99 at 20 °C). Additionally, airborne ultrasound allowed an accurate (mean relative difference 2.3%) prediction of burger thickness., This work was supported by the Agencia Estatal de Investigación in Spain (Project RTC-2017-6314-2 & RTA 2017-00024-C04-03). M.D. Fariñas is grateful for her post-doctoral “Juan de la Cierva” fellowship (FJCI-2017-34,759) through the program funded by the Spanish Ministry of Science, Innovation and Universities., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Ultrasound intensification of Ferrochelatase extraction from pork liver as a strategy to improve ZINC-protoporphyrin formation

  • Abril, B.
  • Sanchez-Torres, E.A.
  • Bou, R.
  • Garcia-Perez, J.V.
  • Benedito, J.
The enzyme Ferrochelatase (FeCH), which is naturally present in pork liver, catalyses the formation of Zinc-protoporphyrin (ZnPP), a natural pigment responsible for the typical color of dry-cured Italian Parma ham. The aim of this study was to evaluate the feasibility of using high power ultrasound in continuous and pulsed modes to intensify the extraction of the enzyme FeCH from pork liver. US application during FeCH extraction led to an improved enzymatic activity and further increase in the formation of ZnPP. The optimal condition tested was that of 1 min in continuous US application, in which time the enzymatic activity increased by 33.3 % compared to conventional extraction (30 min). Pulsed US application required 5 min treatments to observe a significant intensification effect. Therefore, ultrasound is a potentially feasible technique as it increases the catalytic activity of FeCH and saves time compared to the conventional extraction method., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of pork liver drying on ferrochelatase activity for zinc protoporphyrin formation

  • Abril, B.
  • Sanchez-Torres, E.A.
  • Bou, Ricard
  • Benedito, J.
  • Garcia-Perez, Jose V.
Pork liver contains an endogenous enzyme, ferrochelatase (FeCH), which catalyses the formation of zinc protoporphyrin (ZnPP), a natural pigment of great interest for the meat industry. The aim of this study was to analyse the effect of pork liver drying (from −10 to 70 °C), as a stabilisation method, on the FeCH activity (EA) and the apparent concentration (ECapp). Drying temperatures close to room conditions (from 10 to 20 °C) allowed to preserve well the ECapp, while the EA was slightly lower (−15.2%) than in raw liver. However, when drying was conducted at extreme conditions (−10 and 70 °C), the lowest values of ECapp and EA were manifested. Therefore, the drying process at moderate temperatures close to room conditions (10 - 20 °C) was considered to be an effective method for FeCH preservation since it was possible to stabilise the liver and the loss of FeCH activity was minimised., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Role of Enzymatic Reactions in Meat Processing and Use of Emerging Technologies for Process Intensification

  • Abril, Blanca
  • Bou, Ricard
  • García-Pérez, Jose V.
  • Benedito, Jose
Meat processing involves different transformations in the animal muscle after slaughtering, which results in changes in tenderness, aroma and colour, determining the quality of the final meat product. Enzymatic glycolysis, proteolysis and lipolysis play a key role in the conversion of muscle into meat. The accurate control of enzymatic reactions in meat muscle is complicated due to the numerous influential factors, as well as its low reaction rate. Moreover, exogenous enzymes are also used in the meat industry to produce restructured products (transglutaminase), to obtain bioactive peptides (peptides with antioxidant, antihypertensive and gastrointestinal activity) and to promote meat tenderization (papain, bromelain, ficin, zingibain, cucumisin and actinidin). Emerging technologies, such as ultrasound (US), pulsed electric fields (PEF), moderate electric fields (MEF), high-pressure processing (HPP) or supercritical CO2 (SC-CO2), have been used to intensify enzymatic reactions in different food applications. This review aims to provide an overview of the enzymatic reactions taking place during the processing of meat products, how they could be intensified by using emerging technologies and envisage potential applications., This research was financially supported by the “Ministerio de Economía y Competitividad (MINECO)” and the “Instituto Nacional de Investigación y Tecnología Agraria y Alimentaria (INIA)” in Spain (Projects RTA2017-00024-C04-03 and RTA2017-00024-C04-02)., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of ultrasonic application on the enzymatic formation of zinc protoporphyrin

  • Abril, B.
  • Contreras, M.
  • Bou, Ricard
  • Llauger, Mar
  • García-Pérez, J.V.
  • Benedito, J.
Ferrochelatase (FeCH), present in pork liver, catalyses the formation of zinc-protoporphyrin (ZnPP), a stable purple-red pigment found in Parma ham. Kinetics of ZnPP formation is especially slow. Thus, the aim of this study was to improve the ZnPP production using power ultrasound (US) at low (7.05 W/L) and moderate power (36.53 W/L) in homogenised pork liver (HLi) and with added oxyhemoglobin (HLi + OxyHb). ZnPP formation was performed at 37 °C, under anaerobic conditions, for different reaction times (6–48 h). When US was applied at low power, it shortened the time needed to reach maximum ZnPP formation by 50% and increased the yield by 25.77% in the case of HLi and by 4.42% in that of HLi + OxyHb, when compared to the control experiments; however, for the moderate power, ZnPP formation was hindered. Therefore, low power US proved to be an effective method with which to intensify enzymatic ZnPP production., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Strategies for porcine liver valorization as a source of food ingredients

  • Saguer, Elena
  • Abril, Blanca
  • Pateiro, Mirian
  • Bermúdez, Roberto
  • Domínguez-Valencia, Rubén
  • BOU, RICARD
Purpose of Review The sustainable consumption and production goal and the decline of offal consumption have led to the interest in seeking alternatives for porcine livers, the largest edible gland. To that aim, we reviewed the potential of porcine livers as a source of food ingredients together with the use of eco-innovative processes and technologies for their valorization. Recent Findings It is possible to extract and transform various compounds and fractions into food ingredients with tailored techno-functional properties using eco-innovative strategies involving microbial, enzymatic, physical, and chemical processes. These strategies can also contribute to improving the efficacy of different extraction and transformation processes as well as enhance sensory properties. Summary Porcine liver is an interesting source of valuable compounds with multiple food applications and health benefits. Through extraction, processing, and transformation, these compounds can yield versatile food ingredients, thereby optimizing the profitability of this resource for human consumption through alternative presentations and potentially diminishing consumer reluctance compared to the whole liver, This work was funded by the Spanish Ministerio de Ciencia e Innovación and the Agencia Estatal de Investigación [10.13039/501100011033], grant numbers RTA2017-00024 (coordinated projects C01 to C04) and PDC2021-121822 (coordinated projects C21-C22), and by the “European Union NextGenerationEU/PRTR”. We thank the Consolidated Research Group (2021 SGR00468) and CERCA Program from the Generalitat de Catalunya., info:eu-repo/semantics/publishedVersion