Pasar al contenido principal

PROFUNDIZANDO EN EL COMPORTAMIENTO DE MACIZOS ROCOSOS: EFFECTOS DE ESCALA EN LA RESPUESTA TENSO-DEFORMACIONAL DE PROBETAS FISURADAS CON ESPECIAL ATENCION A LA POST-ROTURA

RTI2018-093563-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE VIGO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Study of size effects on the peak and residual strength of intact and artificially fissured granite samples

  • Gonzalez Fernandez, Manuel Alejandro
  • Estevez Ventosa, Xian
  • García Bastante, Fernando Maria
  • Alejano Monge, Leandro Rafael
  • Ferrero, A M
There are not many studies on jointed rock specimens, which can be considered small scale rock mass analogs. On the other hand, the scale effects in the mechanical properties of such samples have seldom been studied. With the aim of continuing previous research on intact granite rocks, the authors have carried out sets of 25 stress-strain triaxial compressive tests on 1 sub-vertical and 2 sub-horizontal 38 mm, 54 mm and 84 mm diameter jointed granite specimens at various confinements. Peak and residual strength values were obtained and compared to those recovered form intact rock samples. Results suggest that peak strength follows similar trends with scale to those observed on intact rock, even if lower strength values are logically recorded. Regarding residual strength, the obtained results are in line with those observed trends for standard size samples, showing a similar trend for all cases independently of scale, even if we observe larger variability for jointed samples. The authors have also compared the values fitting the generalized Hoek-Brown criterion for rock masses to better understand the behavior in relation to sample size. So scale effects clearly appear on jointed rock peak strength of jointed sample; even if residual strength seems hardly affected by scale., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Mechanical behavior of intact and increasingly jointed marble laboratory specimens

  • West, Isabella
  • Walton, Gabriel
  • González Fernández, Manuel
  • Alejano Monge, Leandro Rafael
For many civil and mining engineering structures, rock is the primary construction medium. At engineering scales, the material of interest is the “rockmass,” which contains sections of intact rock separated by a network of pre-existing joints (i.e. fractures). The mechanical behavior of a rockmass is defined by attributes of its intact rock (e.g. strength, stiffness, dilatancy), in addition to attributes of the pre-existing joints (e.g. orientation, surface condition, persistence). Testing representative rockmass specimens in the laboratory is uncommon because of its difficulty due to the required scale. The present study uses laboratory-scale rockmass analog specimens to study the effects that the pre-existing joints have on rockmass mechanical behavior. Smooth joints were sawed into decimeter-scale cylindrical specimens of Carrara marble. Specimens with two joint sets and two different degrees of jointing were tested. Specimens were loaded in compression using a triaxial apparatus under varying levels of confining pressure, and mechanical attributes were calculated including peak strength, residual strength, and pre-peak damage threshold parameters. At the higher end of confining pressures tested (12 MPa), the peak strength of the Carrara marble specimens was not influenced by the presence of pre-existing joints. These results were compared to the results of previous jointed specimen testing on the more brittle Blanco Mera granite. Notably, the drops in peak strength with increasing degrees of jointing were smaller for Carrara Marble than for Blanco Mera granite, which suggests that the Generalized Hoek–Brown failure criterion may not be appropriate to estimate rockmass strength for less brittle rocks., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Residual strength of granitic rocks

  • Alejano Monge, Leandro Rafael
  • Walton, Gabriel
  • Gaines, S.
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, When carrying out compressive tests on rock specimens, a stress plateau is typically attained following peak strength within a strain range a few times larger than the strain at peak strength. This stress level is commonly known as residual strength. A large database of these tests on granitic rock specimens has been compiled and analyzed in detail with the aim of improving understanding of the residual strength of this type of rock. It is observed that physical scale does not significantly change this residual strength. This stress threshold is also shown to be independent of the initial level of jointing in the rock volume. The implication of these findings is that residual strength derived from rock specimen testing can be potentially extended to rock mass scale, at least for granitic rocks. Three one-parameter residual strength models have been used to fit laboratory test residual strength data of granitic rocks, and all of them are shown to reasonably approximate the actual data. Additionally, the residual laboratory strength parameters of all the varied studied granitic rocks for varying scale and pre-jointing tend not to be very different, covering a limited range of values. Ultimately, the potential errors in simple excavation analysis that might result from a priori assumptions regarding the residual strength of granitic rock masses are quantified., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Size-dependent behaviour of hard rock under triaxial loading

  • Gonzalez Fernandez, Manuel Alejandro
  • Estevez Ventosa, Xian
  • Alejano Monge, Leandro Rafael
  • Masoumi, Hossein
Understanding size effects is important to rigorously analyse the behaviour of rocks and rock masses at different scales and for different applications. A number of empirical and numerical studies have included size effects on the uniaxial compressive strength of different rocks, but only few have focussed on the triaxial compressive strength. In this study, several triaxial tests were conducted on granite samples at different confinements (from 0.2 to 15 MPa) and sizes (from 30 to 84 mm in diameter). The most relevant strength parameters were recovered including peak and residual strengths, orientation and frictional response of shear bands. Size effects were observed to be less dominant at high confining pressures for both peak and residual strengths. The resulting data were analysed in the context of size-dependent rock strength theories. For peak strength analyses, the unified size effect law (USEL) and the improved unified size law (IUSEL) were used, in which the double trends, ascending descending behaviours were observed. Size-dependent Hoek–Brown modified failure criteria based on USEL and IUSEL were fit to peak strengths exhibiting a good agreement between the models and the laboratory data. The brittle-ductile transition and the frictional behaviour of shear band under triaxial loading were also analysed. A clear brittle behaviour was particularly observed in samples with large-diameters tested at low confinements. Finally, in regards to frictional behaviour, the shear band angle found to be affected by both confinement and sample size., Ministerio de Ciencia e Innovación | Ref. PRE2019-087397, Ministerio de Ciencia e Innovación | Ref. RTI2018-093563-B-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Size effects on strength and deformability of artificially jointed hard rock

  • González Fernández, Manuel Alejandro
  • Estevez Ventosa, Xian
  • Pérez Rey, Ignacio
  • Alejano Monge, Leandro Rafael
  • Masoumi, Hossein
An extensive experimental study is presented including around 140 triaxial compressive strength tests on artificially jointed hard rock. The experiments were performed on cylindrical and jointed specimens with either 1 sub-vertical and 2 sub-horizontal (1 + 2) or 2 sub-vertical and 3-sub-horizontal (2 + 3) joint sets. The specimen diameter consisted of 38, 54 and 84 mm and the rock was Blanco Mera granite. The confining pressures ranged between 0.2 and 15 MPa and such a testing program complements the previous study in this regard with about 100 triaxial tests on intact rock specimens. A complete set of stress-strain curves were obtained from the experiments followed by extracting the peak and residual strengths as well as indicative deformability parameters (elastic and Poisson’s ratio). For the jointed specimens, the indirect strain measurement was corrected to implicitly calculate the elastic parameters following the energy-based concept. It was found that the peak strength is joint set dependent as per the conventional rock mass classification systems. For jointed specimens a moderate strength size effect was observed in which the peak strength tended to increase with size from 38 mm to 54 mm and then decreased with a rise in specimen diameter. Also, it was concluded that the effect of size on peak strength become less prominent in cases with more joints and the influence of additional jointing becomes less significant for larger specimens; both are novel findings which have not been explored before. The approximated variable elastic parameters of jointed specimens exhibited size independency but joint and confinement dependency, while the variable Poisson’s ratios specifically, appeared to be size and joint set independent. The presented stress-strain data from granite specimens suggests that the mechanical parameters of jointed rock are largely controlled by the rock structure where the specimen size can play a significant role, particularly at low confinements., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00, Universidade de Vigo/CRUE-CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Numerical analysis of anisotropic stiffness and strength for geomaterials

  • Song, Fei
  • González Fernández, Manuel Alejandro
  • Rodríguez Dono, Alfonso
  • Alejano Monge, Leandro Rafael
In numerical modelling, selection of the constitutive model is a critical factor in predicting the actual response of a geomaterial. The use of oversimplified or inadequate models may not be sufficient to reproduce the actual geomaterial behaviour. That selection is especially relevant in the case of anisotropic rocks, and particularly for shales and slates, whose behaviour may be affected, e.g. well stability in geothermal or oil and gas production operations. In this paper, an alternative anisotropic constitutive model has been implemented in the finite element method software CODE_BRIGHT, which is able to account for the anisotropy of shales and slates in terms of both deformability and strength. For this purpose, a transversely isotropic version of the generalised Hooke's law is adopted to represent the stiffness anisotropy, while a nonuniform scaling of the stress tensor is introduced in the plastic model to represent the strength anisotropy. Furthermore, a detailed approach has been proposed to determine the model parameters based on the stress–strain results of laboratory tests. Moreover, numerical analyses are performed to model uniaxial and triaxial tests on Vaca Muerta shale, Bossier shale and slate from the northwest of Spain (NW Spain slate). The experimental data have been recovered from the literature in the case of the shale and, in the case of the slate, performed by the authors in terms of stress-strain curves and strengths. A good agreement can be generally observed between numerical and experimental results, hence showing the potential applicability of the approach to actual case studies. Therefore, the presented constitutive model may be a promising approach for analysing the anisotropic behaviour of rocks and its impact on well stability or other relevant geomechanical problems in anisotropic rocks., Agencia Estatal de Investigación | Ref. RTI 2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Anisotropic deformability and strength of slate from NW-Spain

  • Alejano Monge, Leandro Rafael
  • Gonzalez Fernandez, Manuel Alejandro
  • Estevez Ventosa, Xian
  • Song, Fei
  • Delgado Martín, J.
  • Muñoz Ibáñez, A.
  • González Molano, N.
  • Alvarellos, J.
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Slates are metamorphic rocks characterized by the pervasive occurrence of cleavage or foliation producing a highly anisotropic mechanical behavior characterized by fissility. Deformability and strength of these rocks are therefore dependent on the cleavage plane orientations relative to the principal stresses. In this study, the failure and deformability of these rocks are experimentally investigated by means of a set of standard uniaxial and triaxial compression tests on samples cut with the cleavage forming different angles. Propagation velocity measurements have also been taken in a good number of specimens. Compression tests show that deformability and strength are clearly anisotropic for this rock and that failure through the cleavage plane is observed in the range of dip angles from 15 to 75°. Transversely isotropic elastic parameters are fit based on improved existing approaches. Moreover, the strength of tested samples cut normal and parallel to foliation relevantly differ, something noted qualitatively in the past by some authors in some metamorphic anisotropic rocks. However, this difference has neither been explicitly reported for the case of other foliated sedimentary rocks such as shales, nor formalized in theoretical strength approaches. The triaxial compression experimental data on slates were fit with the Jaeger's plane of weakness (JPW) model. Strength criteria differentiating the strength in directions normal and parallel to foliation are proposed to adapt the JPW model to the observations in slate strength behavior. Other model improvement is proposed, the use of a non-linear strength criterion for the intact rock (Hoek-Brown), which shows to better represent observed strength laboratory results., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Toppling susceptibility of a single rock block resting on a regularly rough base

  • Gui, Jing-Yun
  • Gonzalez Fernandez, Manuel Alejandro
  • Estevez Ventosa, Xian
  • Song, Fei
  • Alejano Monge, Leandro Rafael
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Toppling of individual rock blocks resting on an inclined surface has often been observed in nature. This instability mechanism has typically been analysed for simple block geometries, considering the contact between the block and the base where it lies is a planar surface. In this study, the authors analyse the case where this contact is a regularly rough surface. To do that, the authors resort to analytical limit equilibrium formulations, laboratory physical models and discrete element methods. All these approaches show a consistent trend of behaviour, where roughness does affect the toppling response. Regularly rough surfaces are studied in detail and a general analytical formulation able to show the potential influence of roughness on the block toppling response is derived. Additionally, some considerations are provided regarding the combined effects of rough bases and rounded corners on toppling stability. The authors show how under particular circumstances, roughness can control the potential failure mechanism of a block to produce toppling instead of sliding, and they eventually discuss the impact of rough bases on the toppling response of natural rock blocks., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Influence of microroughness on the frictional behavior and wear response of planar saw-cut rock surfaces

  • Pérez Rey, Ignacio
  • García Bastante, Fernando Maria
  • Alejano Monge, Leandro Rafael
  • Más Ivars, D
Saw-cut rock surfaces, classically utilized to estimate basic friction angle of discontinuities by means of tilt test and other procedures, may seem planar to the naked eye. Nevertheless, they actually present roughness at a micrometric scale. Aiming at characterizing some of these saw-cut rock surfaces and assessing the possible implications between their microscale topography and the resulting tribological behavior, the authors of this study resorted to the 3D focus-variation technique to analyze different surface-texture parameters. Tilt tests were carried out on specimens cut on three rock types, and the involved sliding surfaces were evaluated at a microscale for different testing stages (prior to any test and after two series of repeated tests). An apparently logical inverse correlation between repeated testing and friction angle has been observed, more marked for the smoother surfaces. Higher roughness at the scale of the analysis tends to produce lower friction-angle values, as otherwise observed for mismatched natural rock surfaces. In addition, saw-cut rock surfaces present systematically negative skewness and high values of kurtosis for their height distributions, indicating the occurrence of narrow and deep pits or valleys. Directional hybrid parameters and, in particular, the root mean square (RMS) of the gradient of the surface in the direction of sliding correlates rather well with the measured sliding angle. The authors concluded that the 3D focus-variation technique represents a powerful tool to assess surface-texture parameters of saw-cut rock surfaces, in addition to being useful for understanding some features of the tribological, or wear and frictional, behavior of these type of surfaces., Agencia Estatal de Investigación | Ref. RTI2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Size effects on the tensile strength and fracture toughness of granitic rock in different tests

  • Pérez Rey, Ignacio
  • Muñoz Ibáñez, Andrea
  • González Fernández, Manuel Alejandro
  • Muñiz Menéndez, Mauro
  • Herbón Penabad, Miguel
  • Estevez Ventosa, Xián
  • Delgado Martín, Jordi
  • Alejano Monge, Leandro Rafael
This study investigates the tensile failure mechanisms in granitic rock samples at different scales by means of different types of tests. To do that, we have selected a granitic rock type and obtained samples of different sizes with the diameter ranging from 30 mm to 84 mm. The samples have been subjected to direct tensile strength (DTS) tests, indirect Brazilian tensile strength (BTS) tests and to two fracture toughness testing approaches. Whereas DTS and fracture toughness were found to consistently grow with sample size, this trend was not clearly identified for BTS, where after an initial grow, a plateau of results was observed. This is a rather complete database of tensile related properties of a single rock type. Even if similar databases are rare, the obtained trends are generally consistent with previous scatter and partial experimental programs. However, different observations apply to different types of rocks and experimental approaches. The differences in variability and mean values of the measured parameters at different scales are critically analysed based on the heterogeneity, granular structure and fracture mechanics approaches. Some potential relations between parameters are revised and an indication is given on potential sample sizes for obtaining reliable results. Extending this database with different types of rocks is thought to be convenient to advance towards a better understanding of the tensile strength of rock materials., Agencia Estatal de Investigación | Ref. RTI 2018-093563-B-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Experimental observations and variability assessment of the basic friction angle of rock and concrete saw-cut surfaces under different testing conditions

  • Pérez Rey, Ignacio
  • Mas Ivars, Diego
  • Alejano Monge, Leandro Rafael
  • Arzua Touriño, Javier
Prediction of the shear strength of rock discontinuities is usually performed by resorting to empirical shear strength criteria that depend on different inputs, some of which can be estimated through laboratory tests. Even though these tests are usually developed with rock materials, concrete is often used to make joint replicas. A relevant parameter among those affecting the shear strength behaviour of discontinuities is the basic friction angle, representative of a planar surface and clearly related to the angle of repose of granular materials and solid bodies placed on an inclined plane. Many efforts were carried out by several researchers to suggest a straightforward and simple procedure to obtain this parameter for rock surfaces in a rigorous way by means of tilt tests, which crystallized into an ‘ISRM Suggested Method’. Aiming at complementing basic friction angle results from tests developed under different scenarios and with different materials (rock and concrete), this paper presents an experimental program encompassing more than 500 tilt tests carried out in dry, water-saturated and submerged conditions. Complementarily, a detailed assessment of both rock and concrete surfaces was carried out, in order to study the possible implications between surface topography, wear, mass loss and evolution of the basic friction angle with repeated testing. The basic friction angle of a granite and a concrete has been estimated for three different testing scenarios related to the water content of specimens. A relevant effect of the environmental conditions of the laboratory (humidity and temperature) on results has been detected. Experimental conclusions are complemented with a statistical assessment of results., Agencia Estatal de Investigación | Ref. RTI 2018-093563-B-I00, Swedish Nuclear Fuel and Waste Management Company
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Considerations Relevant to the Stability of Granite Boulders

  • Alejano, Leandro R.
  • Pérez-Rey, Ignacio
  • Múñiz-Menéndez, Mauro
  • Riquelme, Adrián
  • Walton, Gabriel
  • Riquelme, Adrián|||/items/03cd5ff0-7df3-4736-81f3-4d94bd19316a
Granite boulders are characteristic geomorphological structures formed in granitic terrains. Due to their formation process associated with typical spheroidal weathering phenomena, they tend to show more or less ellipsoidal shapes prone to instability, and they often lie on small contact surfaces. Analyzing the stability of these boulders is not a straightforward task. First, these boulders may topple or slide. Additionally, their typically irregular geometry and uneven contact with the surface where they lie makes the analysis more complex. The authors have identified some critical issues that are relevant to characterize these boulders from a rock mechanics point of view, with the aim of estimating the stability of boulders. In particular, an accurate description of the geometry of the boulder is necessary to perform accurate toppling calculations. Additionally, the contact area and the features of the contact plane need to be known in detail. The study is intended to serve as a guideline to address the stability of these granite boulders in a rigorous way, since standard rock mechanics approaches (planar failure, toppling stability, standard rock joint strength criteria, etc.) may not be directly applicable to these particular cases.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Size effects on the tensile strength and fracture toughness of granitic rock in different tests

  • Pérez-Rey, Ignacio
  • Muñoz-Ibáñez, Andrea
  • González Fernández, Manuel Alejandro
  • Muñiz-Menéndez, Mauro
  • Herbón-Penabad, Miguel
  • Estévez-Ventosa, Xian
  • Delgado Martín, Jordi
  • Alejano, Leandro R.
[Abstract:] This study investigates the tensile failure mechanisms in granitic rock samples at different scales by means of different types of tests. To do that, we have selected a granitic rock type and obtained samples of different sizes with the diameter ranging from 30 mm to 84 mm. The samples have been subjected to direct tensile strength (DTS) tests, indirect Brazilian tensile strength (BTS) tests and to two fracture toughness testing approaches. Whereas DTS and fracture toughness were found to consistently grow with sample size, this trend was not clearly identified for BTS, where after an initial grow, a plateau of results was observed. This is a rather complete database of tensile related properties of a single rock type. Even if similar databases are rare, the obtained trends are generally consistent with previous scatter and partial experimental programs. However, different observations apply to different types of rocks and experimental approaches. The differences in variability and mean values of the measured parameters at different scales are critically analysed based on the heterogeneity, granular structure and fracture mechanics approaches. Some potential relations between parameters are revised and an indication is given on potential sample sizes for obtaining reliable results. Extending this database with different types of rocks is thought to be convenient to advance towards a better understanding of the tensile strength of rock materials., The authors affiliated to the University of Vigo acknowledge the Spanish Ministry of Universities for partially funding this study as part of the project awarded under Contract Reference No. RTI2018-093563-B-I00, partially financed by means of ERDF funds from the EU.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Numerical analysis of anisotropic stiffness and strength for geomaterials

  • Song, Fei|||0000-0002-3888-5786
  • González Fernández, Manuel A.
  • Rodríguez Dono, Alfonso|||0000-0002-2296-4826
  • Alejano, Leandro R.
In numerical modelling, selection of the constitutive model is a critical factor in predicting the actual response of a geomaterial. The use of oversimplified or inadequate models may not be sufficient to reproduce the actual geomaterial behaviour. That selection is especially relevant in the case of anisotropic rocks, and particularly for shales and slates, whose behaviour may be affected, e.g. well stability in geothermal or oil and gas production operations. In this paper, an alternative anisotropic constitutive model has been implemented in the finite element method software CODE_BRIGHT, which is able to account for the anisotropy of shales and slates in terms of both deformability and strength. For this purpose, a transversely isotropic version of the generalised Hooke's law is adopted to represent the stiffness anisotropy, while a nonuniform scaling of the stress tensor is introduced in the plastic model to represent the strength anisotropy. Furthermore, a detailed approach has been proposed to determine the model parameters based on the stress–strain results of laboratory tests. Moreover, numerical analyses are performed to model uniaxial and triaxial tests on Vaca Muerta shale, Bossier shale and slate from the northwest of Spain (NW Spain slate). The experimental data have been recovered from the literature in the case of the shale and, in the case of the slate, performed by the authors in terms of stress-strain curves and strengths. A good agreement can be generally observed between numerical and experimental results, hence showing the potential applicability of the approach to actual case studies. Therefore, the presented constitutive model may be a promising approach for analysing the anisotropic behaviour of rocks and its impact on well stability or other relevant geomechanical problems in anisotropic rocks., The experimental part of the slate in this work was funded by REPSOL S.A. The numerical part of this work was supported by the CODE_BRIGHT Project (International Centre for Numerical Methods in Engineering). The work of the second and fourth authors was possible thanks to the Spanish Ministry of Science and Innovation, who funded the project, awarded under Contract Reference No. RTI 2018-093563-B-I00, partially financed by means of the European regional development fund (ERDF) funds from the European Union (EU)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Numerical analysis of anisotropic stiffness and strength for geomaterials

  • Song, Fei
  • González Fernández, Manuel A.
  • Rodríguez Dono, Alfonso
  • Alejano, Leandro R.
In numerical modelling, selection of the constitutive model is a critical factor in predicting the actual response of a geomaterial. The use of oversimplified or inadequate models may not be sufficient to reproduce the actual geomaterial behaviour. That selection is especially relevant in the case of anisotropic rocks, and particularly for shales and slates, whose behaviour may be affected, e.g. well stability in geothermal or oil and gas production operations. In this paper, an alternative anisotropic constitutive model has been implemented in the finite element method software CODE_BRIGHT, which is able to account for the anisotropy of shales and slates in terms of both deformability and strength. For this purpose, a transversely isotropic version of the generalised Hooke's law is adopted to represent the stiffness anisotropy, while a nonuniform scaling of the stress tensor is introduced in the plastic model to represent the strength anisotropy. Furthermore, a detailed approach has been proposed to determine the model parameters based on the stress–strain results of laboratory tests. Moreover, numerical analyses are performed to model uniaxial and triaxial tests on Vaca Muerta shale, Bossier shale and slate from the northwest of Spain (NW Spain slate). The experimental data have been recovered from the literature in the case of the shale and, in the case of the slate, performed by the authors in terms of stress-strain curves and strengths. A good agreement can be generally observed between numerical and experimental results, hence showing the potential applicability of the approach to actual case studies. Therefore, the presented constitutive model may be a promising approach for analysing the anisotropic behaviour of rocks and its impact on well stability or other relevant geomechanical problems in anisotropic rocks., The experimental part of the slate in this work was funded by REPSOL S.A. The numerical part of this work was supported by the CODE_BRIGHT Project (International Centre for Numerical Methods in Engineering). The work of the second and fourth authors was possible thanks to the Spanish Ministry of Science and Innovation, who funded the project, awarded under Contract Reference No. RTI 2018-093563-B-I00, partially financed by means of the European regional development fund (ERDF) funds from the European Union (EU)., Peer Reviewed, Postprint (published version)