Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Single cell induced starvation in a high temperature proton exchange membrane fuel cell stack

  • Alegre Gresa, Cinthia
  • Lozano Fantoba, Antonio
  • Pérez Manso, Ángel
  • Álvarez Manuel, Laura
  • Fernández Marzo, Florencio
  • Barreras Toledo, Félix
This manuscript version is made available under the CC-BY-NC-ND 4.0 license https://creativecommons.org/licenses/by-nc-nd/4.0, Fuel and oxidant starvation are amongst the most critical phenomena affecting fuel cell durability. Reactant starvation during proton exchange membrane fuel cell operation can cause serious irreversible damages. In the present research, the effect of a selective induced starvation of reactant gases on the performance and degradation of a high-temperature PEM fuel cell is studied. A specifically designed 5-cell stack is used, which enables varying the gas supplied to any of the individual cells. The particularity of selectively starving only one cell in a controlled manner is one of the novelties of this study. Two different tests are performed actuating on the central cell (cell 3). They are denoted as moderate and severe starvation, depending on the intensity of the limitation imposed to the gases flowrate. Some relevant and novel results are obtained. It is verified that the performance degradation caused by a moderate starvation of the reactant gases in a cell is reversible. On the contrary, the damages caused by an aggressive gas starvation, which is also maintained in time (30 min), are irreversible. However, the behavior of the rest of the cells is barely affected by the gas starvation to cell 3. Thus, the other major novelty of the present work is the evidence/proof of the ability of a stack with a starved and highly degraded cell, to continue operating, although with a drastic reduction in the total generated current., Authors acknowledge the financial support of the Secretariat of State for Research of the Spanish Ministry of Economy and Competitiveness under project DPI2015-69286-C3-1-R, and the Spanish Ministry of Science, Innovation and Universities under the project RTI2018-096001-B-C31. Support of the Regional Government of Aragon to the Fluid Mechanics for a Clean Energy Research Group (T01_17R) of the LIFTEC is also acknowledged. C. Alegre acknowledges the support of MINECO for her Juan de la Cierva contract and L. Álvarez-Manuel acknowledges the funding provided by the European Social Fund and CSIC under the Youth Employment Initiative., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evaluation of the corrosion resistance of Ni(P)Cr coatings for bipolar plates by electrochemical impedance spectroscopy

  • Marzo, F. F.
  • Alberro, M.
  • Manso, A. P.
  • Garikano, X.
  • Alegre Gresa, Cinthia
  • Montiel, Manuel
  • Lozano Fantoba, Antonio
  • Barreras Toledo, Félix
In the present research, the corrosion resistance of Ni–P and Ni–P–Cr coatings on AA7075-T6 aluminum plates under simulated anodic and cathodic conditions of polymer electrolyte membrane fuel cells (PEMFC) has been studied by electrochemical impedance spectroscopy (EIS). Three Ni–P coatings 20 μm, 30 μm, and 40 μm thick applied by electroless deposition were tested. Besides, a two-layer Ni–P–Cr coating 30 μm thick was also analyzed. It was formed by an inner Ni–P layer, and an outer 10 μm thick chromium one added by electroplating. Corrosion tests were combined with interfacial contact resistance (ICR), roughness, contact angle, and SEM-EDX measurements. The best results were obtained for the 20 μm Ni–P and the two-layer Ni–P–Cr coatings, although the latter showed a high ICR value due to the high electrical resistivity of the chromium oxide surface formed. It was verified that coating degradation occurs when the electrolyte penetrates the micro-cracks and the nodular surface interfaces, reaching the base metal and causing the coating delamination. This behavior is associated with a sharp decrease in the polarization resistance (Rp) of the equivalent circuit model fitted to the EIS results., Authors acknowledge the financial support of the Secretariat of State for Research of the Spanish Ministry of Economy and Competitiveness under project DPI2015-69286-C3-1-R, and the Spanish Ministry of Science, Innovation and Universities under the project RTI2018-096001-B-C31. Support of the Regional Government of Aragon to the Fluid Mechanics for a Clean Energy Research Group (T01_17R) of the LIFTEC is also acknowledged, as well as the technical and human support of the Materials and Surfaces Service provided by SGIker (UPV/EHU/ERDF, EU).