Pasar al contenido principal

DISEÑO EFICIENTE DE SISTEMAS DE CONTROL EN RED INALAMBRICA APLICADOS A UXVS UTILIZANDO TECNICAS DE CONTROL CON MUESTREO NO CONVENCIONAL Y BASADAS EN EVENTOS.

RTI2018-096590-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Autonomous Ground Vehicle Lane-Keeping LPV Model-Based Control: Dual-Rate State Estimation and Comparison of Different Real-Time Control Strategies

  • Salt Ducajú, Julián M.
  • Tomizuka, Masayoshi
  • Salt Llobregat, Julián José|||0000-0002-9640-2658
  • Cuenca, Ángel|||0000-0003-4466-2666
[EN] In this contribution, we suggest two proposals to achieve fast, real-time lane-keeping control for Autonomous Ground Vehicles (AGVs). The goal of lane-keeping is to orient and keep the vehicle within a given reference path using the front wheel steering angle as the control action for a specific longitudinal velocity. While nonlinear models can describe the lateral dynamics of the vehicle in an accurate manner, they might lead to difficulties when computing some control laws such as Model Predictive Control (MPC) in real time. Therefore, our first proposal is to use a Linear Parameter Varying (LPV) model to describe the AGV's lateral dynamics, as a trade-off between computational complexity and model accuracy. Additionally, AGV sensors typically work at different measurement acquisition frequencies so that Kalman Filters (KFs) are usually needed for sensor fusion. Our second proposal is to use a Dual-Rate Extended Kalman Filter (DREFKF) to alleviate the cost of updating the internal state of the filter. To check the validity of our proposals, an LPV model-based control strategy is compared in simulations over a circuit path to another reduced computational complexity control strategy, the Inverse Kinematic Bicycle model (IKIBI), in the presence of process and measurement Gaussian noise. The LPV-MPC controller is shown to provide a more accurate lane-keeping behavior than an IKIBI control strategy. Finally, it is seen that Dual-Rate Extended Kalman Filters (DREKFs) constitute an interesting tool for providing fast vehicle state estimation in an AGV lane-keeping application., This research was funded by the Spanish government Grant Number RTI2018-096590-B-I00
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Robust stability analysis of an energy-efficient control in a Networked Control System with application to Unmanned Ground Vehicles

  • González Sorribes, Antonio|||0000-0003-2690-0472
  • Cuenca, Ángel|||0000-0003-4466-2666
  • Salt Llobregat, Julián José|||0000-0002-9640-2658
  • Jacobs, Jelle
[EN] In this paper, the robust stability and disturbance rejection performance analysis of an energy-efficient control is addressed in the framework of Networked Control System (NCS). The control scheme under study integrates periodic event-triggered control, packet-based control, time-varying Kalman filter, dual-rate control and prediction techniques, whose design is aimed at reducing energy consumption and bandwidth usage. The robust stability against time-varying model uncertainties is analyzed by means of a sufficient condition based on Linear Matrix Inequalities (LMI). Finally, the effectiveness of the proposed approach is experimentally validated in a tracking control for an Unmanned Ground Vehicle (UGV), which is a battery-constrained mobile device with limited computation capacities., This research was funded in part by grant by projects PGC2018-098719-B-I00 (MCIU/AEI/FEDER, UE) , and RTI2018-096590-B-I00 (MCIU/AEI/FEDER, UE) , and by European Commission as part of Project H2020-SEC-2016-2017-Topic: SEC-20-BES-2016-Id: 740736-"C2 Advanced Multi-domain Environment and Live Observation Technologies" (CAMELOT) . Part WP5 supported by Tekever ASDS, Thales Research and Technology, Viasat Antenna Systems, Universitat Politecnica de Valencia, FundacAo da Faculdade de Ciencias da Universidade de Lisboa, Ministerio da Defensa Nacional-Marinha Por-tuguesa, Ministerio da AdministracAo Interna Guarda Nacional Republicana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multirate control strategies for avoiding sample losses. Application to UGV path tracking

  • Salt Llobregat, Julián José|||0000-0002-9640-2658
  • Cuenca, Ángel|||0000-0003-4466-2666
  • Alcaina, José
  • Baños, Alfonso
[EN] When in a digital control strategy there are samples lost due to limitations, different multirate (MR) control options can be used for solving the problem: Dual-rate inferential control (IC) and model-based dual-rate control (MBDR). The objective of this contribution is to analyze, compare, and to assess their behavior under different perspectives. Is a dual-rate inferential control better than a model-based dual-rate control? Both options lead to a periodically time-varying discrete-time system and for this reason a lifted modeling is considered. An efficient algorithm is used for computing a MR system's frequency response for these control structures. The robust performance and disturbance effects are studied in detail under sample losses and process uncertainty, and some considerations are reported. A new QFT (quantitative feedback theory) procedure for dual-rate systems analysis is also described. Analysis and simulation examples and experimental results for UGV path tracking are introduced in this work, revealing that MBDR outperforms IC when the model contains important uncertainties., This work is funded in part by grant RTI2018-096590-B-100 from Spanish government, and by European Commission as part of Project H2020-SEC-2016-2017 -Topic: SEC-20-BES-2016 -Id: 740736 -"C2 Advanced Multi-domain Environment and Live Observation Technologies'' (CAMELOT). Part WP5 supported by Tekever ASDS, Thales Research and Technology, Viasat Antenna Systems, Universitat Politecnica de Valencia, Fundacao da Faculdade de Ciencias da Universidade de Lisboa, Ministerio da Defensa Nacional -Marinha Portuguesa, Ministerio da Administracao Interna Guarda Nacional Republicana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Efficient Design of Wireless Networked Control Systems Applied to UxVs using Non-Conventional Sampling and Event-Based Control Techniques

  • Carbonell-Lázaro, Rafael|||0000-0002-2573-5041
[ES] La tesis doctoral se centra en el diseño eficiente de sistemas de control en red NCS aplicados a Vehículos Autónomos No Tripulados (UxVs), empleando técnicas de muestreo no convencional y control basado en eventos. La investigación aborda desafíos inherentes a los NCS, como el desorden y la pérdida de datos en la comunicación, limitaciones en el ancho de banda de la red, recursos computacionales y energéticos limitados, así como retrasos temporales variables. Se presentan cuatro artículos que contribuyen al tema. El primer y el segundo proponen un control de seguimiento de trayectoria Pure Pursuit para un vehículo terrestre no tripulado (UGV) de tracción en dos ruedas y a cuatro ruedas omnidireccionales, respectivamente, abordando la discrepancia en las frecuencias de muestreo uniforme y no uniforme, respectivamente. El uso de un filtro de Kalman extendido bifrecuencia (DREKF) y no uniforme (NUDREKF), respectivamente, permite estimar las mediciones no disponibles a frecuencia rápida y diseñar un controlador dinámico eficiente con la muestras compensadas por el filtro, logrando hacer un seguimiento efectivo de la trayectoria. Ambos artículos presentan el uso de herramientas de simulación avanzadas como Simscape Multibody que presentan una mayor fidelidad con la realidad. Este tipo de modelado presenta la problemática de la caracterización de parámetros, la cual se resuelve utilizando técnicas que emplean datos de experimentación reales, como se describe en el primer artículo. El tercer artículo presenta una metodología de síntesis de control para robots móviles con configuración diferencial bajo retrasos temporales variables y restricciones de saturación de entrada. Se propone un método de control basado en funciones no lineales estáticas suaves, demostrando convergencia garantizada hacia una posición objetivo con una tasa de decaimiento exponencial. En este artículo empleamos el simulador de Simscape del primer artículo para la simulación realista junto a las técnicas de estimación no uniforme del segundo artículo para la experimentación. El cuarto artículo introduce una estructura de control eficiente en el uso de recursos para el control remoto de seguimiento de trayectorias de vehículos autónomos basada en una combinación integral de filtrado de Kalman, muestreo de bifrecuencia no uniforme, comunicación activada por eventos periódicos y técnicas de control basadas en predicciones de h-pasos adelante, junto a una simulación que permite retardos y pérdidas de paquetes simulando una red inalámbrica. Este enfoque, validado mediante simulación y experimentación en una plataforma robótica holonómica de ruedas omnidireccionales, que ha sido mejorada a partir de la desarrollada en el artículo 2, demuestra una reducción significativa en el uso de recursos computacionales en la parte local en comparación con soluciones de control convencionales junto a un seguimiento de trayectoria satisfactorio. Adicionalmente, destacar que la estabilidad de media cuadrática es asegurada para el NUDREKF. En conjunto, estos artículos contribuyen al diseño eficiente de sistemas de control en red aplicados a UxVs, superando desafíos como retrasos temporales, variabilidad en las frecuencias de muestreo y limitaciones de recursos, y demostrando su efectividad a través de simulaciones realistas y experimentos prácticos., [CA] La tesi doctoral es centra en el disseny eficient de Sistemes de Control en Xarxa (NCS) aplicats a Vehicles Autònoms No Tripulats (UxVs), emprant tècniques de mostreig no convencional i control basat en esdeveniments. La investigació aborda desafiaments inherents als NCS, com el desorde i la pèrdua de dades en la comunicació, limitacions en l'amplada de banda de la xarxa, recursos computacionals i energètics limitats, així com retards temporals variables. Es presenten quatre articles que contribuïxen al tema. El primer i el segon proposen un control de seguiment de trajectòria Pure Pursuit per a un vehicle terrestre no tripulat (UGV) de tracció en dos rodes i a quatre rodes omnidireccionals, respectivament, abordant la discrepància en les taxes de mostreig uniforme i no uniforme, respectivament. L'ús d'un filtre de Kalman estés bifreqüència (DREKF) i no uniforme (NUDREKF), respectivament, permet estimar els mesuraments no disponibles a freqüència ràpida i dissenyar un controlador dinàmic eficient amb la mostres compensades pel filtre, aconseguint fer un seguiment efectiu de la trajectòria. Tots dos articles presenten l'ús de ferramentes de simulació avançades com Simscape Multibody que presenten una major fidelitat amb la realitat. Este tipus de modelatge presenta la problemàtica de la caracterització de paràmetres, la qual es resol utilitzant tècniques que empren dades d'experimentació reals, com es descriu en el primer article. El tercer article presenta una metodologia de síntesi de control per a robots mòbils amb configuració diferencial sota retards temporals variables i restriccions de saturació d'entrada. Es proposa un mètode de control basat en funcions no lineals estàtiques suaus, demostrant convergència garantida cap a una posició objectiu amb una taxa de decaïment exponencial. En este article emprem el simulador de Simscape Multibody del primer article per a la simulació realista junt a les tècniques d'estimació no uniforme del segon article per a l'experimentació. El quart article introduïx una estructura de control eficient en l'ús de recursos per al control remot de seguiment de trajectòries de vehicles autònoms basada en una combinació integral de filtrat de Kalman, mostreig de bifreqüència no uniforme, comunicació activada per esdeveniments periòdics i tècniques de control basades en prediccions d'h-passos avant, al costat d'una simulació que permet retards i pèrdues de paquets simulant una xarxa sense fil. Este enfocament, validat mitjançant simulació i experimentació en una plataforma robòtica holonómica de rodes omnidireccionals, que ha sigut millorada a partir de la desenvolupada en l'article 2, demostra una reducció significativa en l'ús de recursos computacionals en la part local en comparació amb solucions de control convencionals al costat d'un seguiment de trajectòria satisfactori. Addicionalment, cal destacar que l'estabilitat mitjana quadràtica és assegurada per al NUDREKF. En conjunt, estos articles contribuïxen al disseny eficient de sistemes de control en xarxa aplicats a UxVs, superant desafiaments com a retards temporals, variabilitat en les freqüències de mostreig i limitacions de recursos, i demostrant la seua efectivitat a través de simulacions realistes i experiments pràctics., [EN] The doctoral thesis focuses on the efficient design of Networked Control Systems (NCS) applied to Unmanned Autonomous Vehicles (UxVs), employing non-conventional sampling techniques and event-based control. The research addresses inherent challenges in NCS, such as packet disorder and data loss in communication, network bandwidth limitations, limited computational and energy resources, as well as variable time delays. Four articles are presented, contributing to the topic. The first and second articles propose a Pure Pursuit trajectory tracking control for a two-wheel drive Unmanned Ground Vehicle (UGV) and a four-wheel omnidirectional vehicle, respectively, addressing the discrepancy in uniform and non-uniform sampling rates, respectively. The use of uniform Dual-Rate Extended Kalman Filter (DREKF) and non-uniform Dual-Rate Extended Kalman Filter (NUDREKF) enables estimation of high-rate unavailable measurements and design of efficient dynamic controllers with filter-compensated samples, achieving effective trajectory tracking. Both articles employ advanced simulation tools such as Simscape Multibody, which provide higher fidelity to reality. This type of modeling addresses the problem of parameter characterization, which is resolved using techniques employing real-world experimental data, as described in the first article. {The third article presents a control synthesis methodology for mobile robots with differential configuration under variable time delays and input saturation constraints. A control method based on smooth static nonlinear functions is proposed, demonstrating guaranteed convergence to a target position with an exponential decay rate. In this article, we use the Simscape Multibody simulator for realistic simulation as in the first article, along with the non-uniform estimation techniques from the second article for experimentation. The fourth article introduces a resource-efficient control structure for remote trajectory tracking control of autonomous vehicles, based on a comprehensive combination of Kalman filtering, non-uniform dual-rate sampling, periodic event-triggered communication, and h-steps ahead prediction-based control techniques, alongside a simulation that incorporates delays and packet losses to simulate a wireless network. This approach, validated through simulation and experimentation on a holonomic omnidirectional-wheeled robotic platform modeled in the second article, demonstrates significant reduction in computational resource usage on the local side compared to conventional control solutions, along with satisfactory trajectory tracking. Additionally, it is worth highlighting that the stability of the NUDREKF is guaranteed through stability conditions. Together, these articles contribute to the efficient design of NCS applied to UxVs, overcoming challenges such as time delays, variability in sampling rates, and resource limitations, and demonstrating their effectiveness through realistic simulations and practical experiments., This PhD research was part of the R+D+i Project, Grant RTI2018-096590-B- I00 (Research, Development and Innovation projects - "Research Challengues"), funded by MCIN/AEI/ 10.13039/501100011033 (Ministry of Science, Innova- tion and Universities - Spanish government) and by Europe "ERDF A way of making Europe". And grant for predoctoral contracts for the training of doc- tors, Grant PRE2019-088467 funded by MCIN/AEI/10.13039 /501100011033 and by Europe "ESF Investing in your future".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dual-Rate Extended Kalman Filter Based Path-Following Motion Control for an Unmanned Ground Vehicle: Realistic Simulation

  • Carbonell-Lázaro, Rafael|||0000-0002-2573-5041
  • Cuenca, Ángel|||0000-0003-4466-2666
  • Casanova Calvo, Vicente|||0000-0002-7040-4815
  • Pizá, Ricardo|||0000-0001-8261-0045
  • Salt Llobregat, Julián José|||0000-0002-9640-2658
[EN] In this paper, a two-wheel drive unmanned ground vehicle (UGV) path-following motion control is proposed. The UGV is equipped with encoders to sense angular velocities and a beacon system which provides position and orientation data. Whereas velocities can be sampled at a fast rate, position and orientation can only be sensed at a slower rate. Designing a dynamic controller at this slower rate implies not reaching the desired control requirements, and hence, the UGV is not able to follow the predefined path. The use of dual-rate extended Kalman filtering techniques enables the estimation of the fast-rate non-available position and orientation measurements. As a result, a fast-rate dynamic controller can be designed, which is provided with the fast-rate estimates to generate the control signal. The fast-rate controller is able to achieve a satisfactory path following, outperforming the slow-rate counterpart. Additionally, the dual-rate extended Kalman filter (DREKF) is fit for dealing with non-linear dynamics of the vehicle and possible Gaussian-like modeling and measurement uncertainties. A Simscape Multibody (TM) (Matlab(R)/Simulink) model has been developed for a realistic simulation, considering the contact forces between the wheels and the ground, not included in the kinematic and dynamic UGV representation. Non-linear behavior of the motors and limited resolution of the encoders have also been included in the model for a more accurate simulation of the real vehicle. The simulation model has been experimentally validated from the real process. Simulation results reveal the benefits of the control solution., Grant RTI2018-096590-B-I00 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF Away of making Europe" and Grant PRE2019-088467 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Nonuniform Dual-Rate Extended Kalman-Filter-Based Sensor Fusion for Path-Following Control of a Holonomic Mobile Robot with Four Mecanum Wheels

  • Pizá, Ricardo|||0000-0001-8261-0045
  • Carbonell-Lázaro, Rafael|||0000-0002-2573-5041
  • Casanova Calvo, Vicente|||0000-0002-7040-4815
  • Cuenca, Ángel|||0000-0003-4466-2666
  • Salt Llobregat, Julián José|||0000-0002-9640-2658
[EN] This paper presents an extended Kalman-filter-based sensor fusion approach, which enables path-following control of a holonomic mobile robot with four mecanum wheels. Output measurements of the mobile platform may be sensed at different rates: odometry and orientation data can be obtained at a fast rate, whereas position information may be generated at a slower rate. In addition, as a consequence of possible sensor failures or the use of lossy wireless sensor networks, the presence of the measurements may be nonuniform. These issues may degrade the path-following control performance. The consideration of a nonuniform dual-rate extended Kalman filter (NUDREKF) enables us to estimate fast-rate robot states from nonuniform, slow-rate measurements. Providing these estimations to the motion controller, a fast-rate control signal can be generated, reaching a satisfactory path-following behavior. The proposed NUDREKF is stated to represent any possible sampling pattern by means of a diagonal matrix, which is updated at a fast rate from the current, existing measurements. This fact results in a flexible formulation and a straightforward algorithmic implementation. A modified Pure Pursuit path-tracking algorithm is used, where the reference linear velocity is decomposed into Cartesian components, which are parameterized by a variable gain that depends on the distance to the target point. The proposed solution was evaluated using a realistic simulation model, developed with Simscape Multibody (Matlab/Simulink), of the four-mecanum-wheeled mobile platform. This model includes some of the nonlinearities present in a real vehicle, such as dead-zone, saturation, encoder resolution, and wheel sliding, and was validated by comparing real and simulated behavior. Comparison results reveal the superiority of the sensor fusion proposal under the presence of nonuniform, slow-rate measurements., Grant RTI2018-096590-B-I00 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe" and Grant PRE2019-088467 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Remote Control Strategy for an Autonomous Vehicle with Slow Sensor Using Kalman Filtering and Dual-Rate Control

  • Cuenca, Ángel|||0000-0003-4466-2666
  • Salt Llobregat, Julián José|||0000-0002-9640-2658
  • Zhan, Wei
  • Alcaina-Acosta, José Joaquín
  • Tang, Chen
  • Tomizuka, Masayoshi
[EN] This work presents a novel remote control solution for an Autonomous Vehicle (AV), where the system structure is split into two sides. Both sides are assumed to be synchronized and linked through a communication network, which introduces time-varying delays and packet disorder. An Extended Kalman Filter (EKF) is used to cope with the non-linearities that appear in the global model of the AV. The EKF fuses the data provided by the sensing devices of the AV in order to estimate the AV state, reducing the noise effect. Additionally, the EKF includes an h-step-ahead state prediction stage, which, together with the consideration of a packet-based control strategy, enables facing the network-induced delays. Since the AV position is provided by a camera, which is a slow sensing device, a dual-rate controller is required to achieve certain desired (nominal) dynamic control performance. The use of a dual-rate control framework additionally enables saving network bandwidth and deals with packet disorder. As the path-tracking control algorithm, pure pursuit is used. Application results show that, despite existing communication problems and slow-rate measurements, the AV is able to track the desired path, keeping the nominal control performance., This research work has been developed as a result of a mobility stay funded by Spanish Ministry of Education under "Programa Estatal de Promocion del Talento y su Empleabilidad en I+D+i, Subprograma Estatal de Movilidad, del Plan Estatal de Investigacion Cientifica y Tecnica y de Innovacion 2013-2016". In addition, the research was funded in part by Grant RTI2018-096590-B-I00 from the Spanish government and by the European Commission as part of Project H2020-SEC-2016-2017, Topic: SEC-20-BES-2016, ID: 740736, "C2 Advanced Multi-domain Environment and Live Observation Technologies" (CAMELOT). Part WP5 supported by Tekever ASDS, Thales Research and Technology, Viasat Antenna Systems, Universitat Politecnica de Valencia, Fundacao da Faculdade de Ciencias da Universidade de Lisboa, Ministerio da Defensa Nacional, Marinha Portuguesa, and Ministerio da Administracao Interna Guarda Nacional Republicana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A QFT approach to robust dual-rate control systems

  • Baños, Alfonso
  • Salt Llobregat, Julián José|||0000-0002-9640-2658
  • Casanova Calvo, Vicente|||0000-0002-7040-4815
[EN] A dual-rate control system is a hybrid system composed of continuous-time and discrete-time elements with two sampling frequencies. In this work, a new frequency domain analysis and design approach, based on the quantitative feedback theory is developed, to cope with robust stability and robust tracking specifications. Tracking specifications are considered not only in the discrete-time but also in continuous-time, that allow a precise description of the intersample behavior (ripples), and characterization of frequencies below and beyond the Nyquist frequencies. Several illustrative examples and a case study has been developed., Fundacion Seneca, Grant/Award Number: 20842/PI/18; MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe", Grant/Award Numbers: PID2020-112709RB-C22, RTI2018-096590-B-I00
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Distributed Event-Triggered Flocking Control of Lagrangian Systems

  • Aranda-Escolastico, Ernesto
  • Colombo, Leonardo J.
  • Guinaldo, María
In this letter, an event-triggered control protocol is developed to investigate flocking control of Lagrangian systems, where event-triggering conditions are proposed to determine when the velocities of the agents are transmitted to their neighbors. In particular, the proposed controller is distributed, since it only depends on the available information of each agent on their own reference frame. In addition, we derive sufficient conditions to avoid Zeno behavior. Numerical simulations are provided to show the effectiveness of the proposed control law., 10.13039/501100004837-Ministerio de Ciencia e Innovación (Grant Number: CICYT RTI2018-094665-B-I00 and RTI2018-096590-B-I00) 10.13039/501100011033-Agencia Estatal de Investigación (AEI) (Grant Number: PID2020-112658RB-I00/AEI/10.13039/501100011033) “la Caixa” Foundation through the Project “Decentralized Strategies for Cooperative Robotic Swarms” (Grant Number: LCF/BQ/PI19/11690016) 10.13039/501100004837-Ministerio de Ciencia e Innovación (Grant Number: PID2019-106715GBC21), Peer reviewed