Pasar al contenido principal

ENVASE ACTIVO MULTICAPA TERMOFORMABLE DE ALTA BARRERA BASADO EN ECONOMIA BIOCIRCULAR

RTI2018-097249-B-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT JAUME I DE CASTELLO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of the Compatibilization Effect of Different Reactive Agents in PHB/Natural Fiber-Based Composites

  • Sánchez-Safont, Estefanía Lidón
  • Aldureid, Abdulaziz
  • Lagarón Cabello, José María
  • Cabedo, Luis
  • Gámez-Pérez, José
© 2020 by the authors., Fiber–matrix interfacial adhesion is one of the key factors governing the final properties of natural fiber-based polymer composites. In this work, four extrusion reactive agents were tested as potential compatibilizers in polyhydroxylbutyrate (PHB)/cellulose composites: dicumyl peroxide (DCP), hexamethylene diisocyanate (HMDI), resorcinol diglycidyl ether (RDGE), and triglycidyl isocyanurate (TGIC). The influence of the fibers and the different reactive agents on the mechanical properties, physical aging, and crystallization behavior were assessed. To evaluate the compatibilization effectiveness of each reactive agent, highly purified commercial cellulose fibers (TC90) were used as reference filler. Then, the influence of fiber purity on the compatibilization effect of the reactive agent HMDI was evaluated using untreated (U_RH) and chemically purified (T_RH) rice husk fibers, comparing the results with the ones using TC90 fibers. The results show that reactive agents interact with the polymer matrix at different levels, but all compositions showed a drastic embrittlement due to the aging of PHB. No clear compatibilization effect was found using DCP, RDGE, or TGIC reactive agents. On the other hand, the fiber–polymer interfacial adhesion was enhanced with HMDI. The purity of the fiber played an important role in the effectiveness of HMDI as a compatibilizer, since composites with highly purified fibers showed the greatest improvements in tensile strength and the most favorable morphology. None of the reactive agents negatively affected the compostability of PHB. Finally, thermoformed trays with good mold reproducibility were successfully obtained for PHB/T_RH/HMDI composition., The authors would like to thank the financial support for this research from Ministerio de Ciencia e Innovación (RTI2018-097249-B-C22), Pla de Promoció de la Investigació de la Universitat Jaume I (UJI-B2019-44) and H2020 EU Project YPACK (H2020-SFS-2017-1, Reference 773872)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of the Purification Treatment on the Valorization of Natural Cellulosic Residues as Fillers in PHB-Based Composites for Short Shelf Life Applications

  • Sánchez-Safont, Estefanía Lidón
  • Aldureid, Abdulaziz
  • Lagarón Cabello, José María
  • Gámez Pérez, José
  • Cabedo, Luis
In this work the effect of a combined NaOH + peracetic acid (PAA) purification treatment on the valorization of almond shell (AS) and rice husk (RH) lignocellulosic residues as fillers in PHB-based composites for short shelf life applications has been studied. The efficiency of the treatment at removing the non-cellulosic components of the fibers has been evaluated by SEM, FTIR, WAXS and TGA taking a commercial cellulose as reference. The influence of the untreated and treated fibers on the morphology, thermal, crystallization, tensile properties, fracture toughness and dynamo mechanical behavior of the PHB/fiber composites has been studied. The treatment has demonstrated its ability at removing the lignin, hemicelluloses and waxes allowing the obtention of fibers with relative crystallinity, thermal stability and composition similar to the commercial cellulose. The different agro-food based lignocellulosic residues used resulted in two suitable reinforcing fillers for a PHB matrix. Hence, composites prepared with the treated fibers presented better thermal and mechanical performance than those prepared with the untreated ones. Therefore, the so-obtained purified residue fibers are comparable to a pure cellulose as a filler for PHB composites., The authors would like to thank the financial support for this research from Ministerio de Ciencia, Innovación y Universidades (RTI2018-097249-B-C22), Pla de Promoció de la Investigació de la Universitat Jaume I (UJI-B2019-44) and H2020 EU Project YPACK (H2020-SFS-2017-1, Reference 773872). Authors would like to acknowledge the Instituto de Tecnología de Materiales of Universitat Politècnica de València-Campus de Alcoy, the Unidad Asociada IATA-UJI “Polymers Technology” and Servicios Centrales de Instrumentación Científica (SCIC) of Universitat Jaume I., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Role of Plasticizers on PHB/bio-TPE Blends Compatibilized by Reactive Extrusion

  • Samaniego, Kerly
  • Matos, Armando
  • Sánchez-Safont, Estefanía
  • Candal, María V.
  • Lagarón Cabello, José María
  • Cabedo, Luis
  • Gámez Pérez, José
Poly(hydroxybutyrate) (PHB) is a biopolymer biologically synthesized by controlled bacterial fermentation from a wide variety of microorganisms. PHB is proposed as a potential green alternative to commonly used plastics in packaging, due to its biodegradability and biocompatibility. However, if PHB is to replace commodities, it has some limitations regarding its thermo-mechanical performance to overcome. Among them are its critically the low toughness values at room temperature and poor thermoforming ability. With the aim of overcoming these weaknesses, in this work, blends of PHB with the addition of a biodegradable thermoplastic elastomer (bio-TPE) were prepared and evaluated. Films of such compounds were made by cast extrusion. In order to enhance the compatibility of both polymers during the extrusion process, three different reactive agents (poly-hexametylene diisocianate, triglycidyl isocyanurate, and Joncryl® ADR-4368) were assessed. The morphology and mechanical- and thermal properties of the films obtained were analyzed. In addition, the thermoforming ability of the produced films was evaluated. The results show that the plasticizers present in the bio-TPE interacted with the reactive agents, making them chemical competitors and altering the outcome of the blends., This research was supported by MCIN/AEI/ 10.13039/501100011033 and FEDER “Una manera de hacer Europa”, project number I+D+i RTI2018-097249-B-C22. In addition, this work has also been granted with the financial support of the Universitat Jaume I, UJI-B2019-44., Peer reviewed