Pasar al contenido principal

MODELIZACION Y COMPUTACION PARA UNA NUEVA GENERACION DE CELULAS FLEXO-FOTOVOLTAICAS

RTI2018-101662-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Switchable tribology of ferroelectrics

  • Cho, Seongwoo
  • Gaponenko, Iaroslav
  • Cordero-Edwards, Kumara
  • Barceló-Mercader, Jordi
  • Arias, Irene
  • Kim, Daeho
  • Lichtensteiger, Céline
  • Yeom, Jiwon
  • Musy, Loïc
  • Kim, Hyunji
  • Han, Seung Min
  • Catalán, Gustau
  • Paruch, Patrycja
  • Hong, Seungbum
Switchable tribological properties of ferroelectrics offer an alternative route to visualize and control ferroelectric domains. Here, we observe the switchable friction and wear behavior of ferroelectrics using a nanoscale scanning probe—down domains have lower friction coefficients and show slower wear rates than up domains and can be used as smart masks. This asymmetry is enabled by flexoelectrically coupled polarization in the up and down domains under a sufficiently high contact force. Moreover, we determine that this polarization-sensitive tribological asymmetry is widely applicable across various ferroelectrics with different chemical compositions and crystalline symmetry. Finally, using this switchable tribology and multi-pass patterning with a domain-based dynamic smart mask, we demonstrate three-dimensional nanostructuring exploiting the asymmetric wear rates of up and down domains, which can, furthermore, be scaled up to technologically relevant (mm–cm) size. These findings demonstrate that ferroelectrics are electrically tunable tribological materials at the nanoscale for versatile applications., S.H. acknowledges the National Research Foundation of Korea (NRF) grant funded by the Korean government (MSIT) (Grant No. 2020R1A2C2012078, NRF-2022K1A4A7A04095892 and RS-2023-00247245) and the KAIST-funded Global Singularity Research Program for 2022 and 2023. P.P. acknowledges Division II of the Swiss National Science Foundation under project 200021_178782. S.C. acknowledges the National Research Foundation of Korea (NRF) grant funded by the Korean government (NRF-2018-Global Ph.D. Fellowship Program). I.A. acknowledges the support of the European Research Council (No. StG-679451 to I.A.), the Spanish Ministry of Economy and Competitiveness (No. RTI2018-101662-B-I00), and the Generalitat de Catalunya (ICREA Academia award for excellence in research to I.A. and Grant No. 2017-SGR-1278 to I.A.). CIMNE is a Severo Ochoa Centre of Excellence (2019-2023) under the grant CEX2018-000797-S to I.A. funded by MCIN/AEI/10.13039/501100011033., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000797-S)., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A C0 interior penalty Finite Element Method for flexoelectricity

  • Ventura, Jordi
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
This is a post-peer-review, pre-copyedit version of an article published in Journal of scientific computing. The final authenticated version is available online at: http://dx.doi.org/10.1007/s10915-021-01613-w, We propose a C0 Interior Penalty Method (C0-IPM) for the computational modelling of flexoelectricity, with application also to strain gradient elasticity, as a simplified case. Standard high-order C0 finite element approximations, with nodal basis, are considered. The proposed C0-IPM formulation involves second derivatives in the interior of the elements, plus integrals on the mesh faces (sides in 2D), that impose C1 continuity of the displacement in weak form. The formulation is stable for large enough interior penalty parameter, which can be estimated solving an eigenvalue problem. The applicability and convergence of the method is demonstrated with 2D and 3D numerical examples., This work was supported by the European Research Council (StG679451 to Irene Arias), Agencia Estatal de Investigaci´on (RTI2018-101662-B-I00), Ministerio de Econom´ıa y Competitividad (CEX2018-000797-S) and Generalitat de Catalunya (2017- SGR-1278), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems

  • Barceló Mercader, Jordi
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
  • Arias Vicente, Irene|||0000-0002-6761-3499
This is the peer reviewed version of the following article: Barcelo, J. [et al.]. Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems. "International journal for numerical methods in engineering", 28 Febrer 2022, vol. 123, núm. 4, p. 901-923, which has been published in final form at DOI10.1002/nme.6882. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., We present a formulation for the weak enforcement of continuity conditions atmaterialinterfacesinhigh-orderproblemsbymeansofNitsche’smethod,whichis particularly suited for unfitted discretizations. This formulation is extendedto impose generalized periodicity conditions at the unit cell boundaries of peri-odic structures. The formulation is derived for flexoelectricity, a high-orderelectromechanical coupling between strain gradient and electric field, mathe-matically modeled as a coupled system of fourth-order PDEs. The design of flex-oelectricdevicesrequiresthesolutionofhigh-orderboundaryvalueproblemsoncomplex material architectures, including general multimaterial arrangements.ThiscanbeefficientlyachievedwithanimmersedboundaryB-splinesapproach.Furthermore, the design of flexoelectric metamaterials also involves the anal-ysis of periodic unit cells with generalized periodicity conditions. Optimalhigh-order convergence rates are obtained with an unfitted B-spline approxi-mation, confirming the reliability of the method. The numerical simulationsillustrate the usefulness of the proposed approach toward the design of func-tional electromechanical multimaterial devices and metamaterials harnessingthe flexoelectric effect., Departament d'Universitats, Recerca i Societat de la Informació, 2017-SGR-1278; ICREA Academia; H2020 European Research Council, StG-679451; Secretaría de Estado de Investigación, Desarrollo e Innovación, CEX2018-000797-S; RTI2018-101662-B-I00., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Flexoelectricity causes surface piezoelectric-like effects in dielectrics

  • Mohammadi, Hossein|||0000-0003-2716-9028
  • Greco, Francesco|||0000-0001-6126-493X
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Arias Vicente, Irene|||0000-0002-6761-3499
In this paper, we study the surface effects that bulk flexoelectric models exhibit in finite samples. We first show that flexoelectric materials do not exhibit electromechanical response under homogeneous loading when the body is infinite. However, when the size of the body is finite, due to the symmetry-breaking nature of surfaces, homogeneous loading (mechanical or electrical) can cause an electromechanical response near the surfaces. We obtain closed-form solutions for finite samples under different electromechanical loading conditions and show that the electromechanical response caused by the bulk flexoelectric effect is reminiscent of surface piezoelectricity, causing boundary layers in certain components of the strains and/or electric fields near the free surfaces., This work was supported by the Generalitat de Catalunya (“ICREA Academia” award for excellence in research to I.A., and Grants No. 2017-SGR-1278 and 2021-SGR-01049), the European Research Council (StG-679451 to I.A.), and the Spanish Ministry of Economy and Competitiveness (Grant PID2023-152533OB-I00 funded by MICIU/AEI/10.13039/501100011033/ERDF/EU, and Grant RTI2018-101662-B-I00). D.C. acknowledges the support of the Spanish Ministry of Universities through the Margarita Salas fellowship (European Union - NextGenerationEU). H.M. received the support of a fellowship from “la Caixa” Foundation (ID 100010434). The fellowship code is LCF/BQ/DI20/11780036. CIMNE is recipient of a Severo Ochoa Award of Excellence from the MINECO., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A C0 Interior Penalty Finite Element method for flexoelectricity at finite deformations

  • Pérez Escudero, Sergi|||0009-0005-6205-4260
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
© 2025 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC license (http://creativecommons.org/licenses/by-nc/4.0/)., The 4th-order partial differential equations modeling the flexoelectric effect at finite deformations are considered, accounting for direct and converse effects. Its numerical solution, using standard C0 Finite Elements, is carried out through the development of a C0 Interior Penalty method (C0 -IPM) with a Newton–Raphson nonlinear solver. The simulation of metamaterials by means of generalized periodicity conditions is also addressed within the C0 -IPM framework. The order of convergence of the method is assessed in a synthetic test, studying the effect of the penalty parameters in the accuracy of the scheme. The method is also applied to the solution of a cantilever beam problem, and to the simulation of metamaterials at large deformations., This work was supported by the Agència de Gestió d’Ajuts Universitaris i de Recerca (training grant FI-AGAUR 2022 to Sergi Pérez-Escudero), Ministerio de Ciencia, Innovación y Universidades (PID2023-152533OB-I00 funded by MICIU/AEI/10.13039/501100011033/ERDF/EU, and RTI2018-101662-B-I00), and Generalitat de Catalunya (2021-SGR-01049)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A comparison of formulations and non-linear solvers for computational modeling of semiconductor devices

  • Pérez Escudero, Sergi|||0009-0005-6205-4260
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Arias Vicente, Irene|||0000-0002-6761-3499
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
© The Author(s) 2024, The drift-diffusion formulation, modelling semiconductor materials in terms of carrier densities and electric potential, is considered together with an alternative formulation in terms of dimensionless logarithmic quantities. Stability of both formulations in presence of sharp variations with a Galerkin Finite Element discretisation is assessed in two realistic problems: a p-n junction and an n-MOSFET device. The robustness with respect to the initial guess and the computational efficiency of the Newton-Raphson and Gummel non-linear solvers are also compared., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. s This work was supported by the Agència de Gestió d’Ajuts Universitaris i de Recerca (training grant FI-AGAUR 2022 to Sergi Pèrez-Escudero), the European Research Council (StG679451 to Irene Arias), Agencia Estatal de Investigación (RTI2018-101662-B-I00), Ministerio de Economía y Competitividad (CEX2018-000797-S), and Generalitat de Catalunya (2017-SGR-1278)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Continuum and computational modeling of surface effects in flexoelectric materials

  • Dingle Palmer, Mònica|||0000-0002-8137-6469
  • Arias Vicente, Irene|||0000-0002-6761-3499
  • Codony Gisbert, David|||0000-0002-7341-9799
In recent times, with the rise of nanoscale technologies, miniaturization of devices has prompted the need to study electromechanical phenomena at small scales. Most studies focus on the phenomena occurring at the bulk portion of the material, such as flexoelectricity, but neglect the effects that arise from the surfaces of the samples. Given the fact that, at such scales, surface-to-volume ratio is inherently large, surface effects cannot be ignored if the full and accurate description of the material’s response wants to be provided. In this work, we present a model that successfully integrates flexoelectricity and the effects of surfaces, and we properly derive the governing equations and boundary conditions for the boundary value problem. We also present a numerical approach in order to computationally solve it, converging at high-order optimal rates. In addition, we present an analytical 1D Euler–Bernoulli electromechanical beam model. Numerically, we find the presence of boundary layers in the transversal electric field across the beam thickness, which are not accounted for in the analytical 1D model. Finally, we find numerical solutions for geometrically-polarized flexoelectric lattice metamaterials, which have large area-to-volume ratios, giving rise to very relevant surface effects. This work emphasizes the importance of accounting for surface effects in modeling and design of flexoelectric devices, including geometrically-polarized metamaterials., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

C0-IPM with generalised periodicity and application to flexoelectricity-based 2D metamaterials

  • Balcells Quintana, Oscar
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
The version of record is available online at: http://dx.doi.org/10.1007/s10915-022-01848-1, We propose a methodology to solve high-order PDE boundary value problems with generalised periodicity, in the framework of the C0 interior penalty method. The method is developed for the analysis of flexoelectricity- based metamaterial unit cells, formalising the corresponding problem statement and weak form, and giving details on the implementation of the local and macro conditions for generalised periodicity. Numerical examples demonstrate the high-order convergence of the method and its applicability in realistic problem settings., This work was supported by the European Research Council (StG-679451 to Irene Arias), Agencia Estatal de Investigación (RTI2018-101662-B-I00),Ministerio de Economía y Competitividad (CEX2018- 000797-S) and Generalitat de Catalunya (2017-SGR-1278), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Topology optimization of flexoelectric metamaterials with apparent piezoelectricity

  • Greco, Francesco|||0000-0001-6126-493X
  • Codony Gisbert, David|||0000-0002-7341-9799
  • Mohammadi, Hossein|||0000-0003-2716-9028
  • Fernández Méndez, Sonia|||0000-0002-9305-7684
  • Arias Vicente, Irene|||0000-0002-6761-3499
The flexoelectric effect, coupling polarization and strain gradient as well as strain and electric field gradients, is universal to dielectrics, but, as compared to piezoelectricity, it is more difficult to harness as it requires field gradients and it is a small-scale effect. This drawback can be overcome by suitably designing multiscale metamaterials made of a non-piezoelectric base material but exhibiting apparent piezoelectricity. We develop a theoretical and computational framework to perform topology optimization of the representative volume element of such metamaterials by accurately modeling the governing equations of flexoelectricity using a Cartesian B-spline method, describing geometry with a level set, and resorting to genetic algorithms for optimization. We consider a multi-objective optimization problem where area fraction competes with each one of the four fundamental piezoelectric functionalities (stress/strain sensor/actuator). We computationally obtain Pareto fronts, and discuss the different geometries depending on the apparent piezoelectric coefficient being optimized. Our results show that optimal material architectures strongly depend on the specific functional property being optimized, and that, except for stress actuators, optimal structures are low-area-fraction lattices. In general, we find competitive estimations of apparent piezoelectricity as compared to reference materials such as quartz and PZT ceramics. This opens the possibility to design devices for sensing, actuation and energy harvesting from a much wider, cheaper and effective class of materials., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems

  • Barceló Mercader, Jordi
  • Codony Gisbert, David
  • Fernández Méndez, Sonia
  • Arias Vicente, Irene
This is the peer reviewed version of the following article: Barcelo, J. [et al.]. Weak enforcement of interface continuity and generalized periodicity in high-order electromechanical problems. "International journal for numerical methods in engineering", 28 Febrer 2022, vol. 123, núm. 4, p. 901-923, which has been published in final form at DOI10.1002/nme.6882. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., We present a formulation for the weak enforcement of continuity conditions atmaterialinterfacesinhigh-orderproblemsbymeansofNitsche’smethod,whichis particularly suited for unfitted discretizations. This formulation is extendedto impose generalized periodicity conditions at the unit cell boundaries of peri-odic structures. The formulation is derived for flexoelectricity, a high-orderelectromechanical coupling between strain gradient and electric field, mathe-matically modeled as a coupled system of fourth-order PDEs. The design of flex-oelectricdevicesrequiresthesolutionofhigh-orderboundaryvalueproblemsoncomplex material architectures, including general multimaterial arrangements.ThiscanbeefficientlyachievedwithanimmersedboundaryB-splinesapproach.Furthermore, the design of flexoelectric metamaterials also involves the anal-ysis of periodic unit cells with generalized periodicity conditions. Optimalhigh-order convergence rates are obtained with an unfitted B-spline approxi-mation, confirming the reliability of the method. The numerical simulationsillustrate the usefulness of the proposed approach toward the design of func-tional electromechanical multimaterial devices and metamaterials harnessingthe flexoelectric effect., Departament d'Universitats, Recerca i Societat de la Informació, 2017-SGR-1278; ICREA Academia; H2020 European Research Council, StG-679451; Secretaría de Estado de Investigación, Desarrollo e Innovación, CEX2018-000797-S; RTI2018-101662-B-I00., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A comparison of formulations and non-linear solvers for computational modeling of semiconductor devices

  • Pérez Escudero, Sergi
  • Codony Gisbert, David
  • Arias Vicente, Irene
  • Fernández Méndez, Sonia
© The Author(s) 2024, The drift-diffusion formulation, modelling semiconductor materials in terms of carrier densities and electric potential, is considered together with an alternative formulation in terms of dimensionless logarithmic quantities. Stability of both formulations in presence of sharp variations with a Galerkin Finite Element discretisation is assessed in two realistic problems: a p-n junction and an n-MOSFET device. The robustness with respect to the initial guess and the computational efficiency of the Newton-Raphson and Gummel non-linear solvers are also compared., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. s This work was supported by the Agència de Gestió d’Ajuts Universitaris i de Recerca (training grant FI-AGAUR 2022 to Sergi Pèrez-Escudero), the European Research Council (StG679451 to Irene Arias), Agencia Estatal de Investigación (RTI2018-101662-B-I00), Ministerio de Economía y Competitividad (CEX2018-000797-S), and Generalitat de Catalunya (2017-SGR-1278)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Flexoelectricity causes surface piezoelectric-like effects in dielectrics

  • Mohammadi, Hossein
  • Greco, Francesco
  • Codony Gisbert, David
  • Arias Vicente, Irene
In this paper, we study the surface effects that bulk flexoelectric models exhibit in finite samples. We first show that flexoelectric materials do not exhibit electromechanical response under homogeneous loading when the body is infinite. However, when the size of the body is finite, due to the symmetry-breaking nature of surfaces, homogeneous loading (mechanical or electrical) can cause an electromechanical response near the surfaces. We obtain closed-form solutions for finite samples under different electromechanical loading conditions and show that the electromechanical response caused by the bulk flexoelectric effect is reminiscent of surface piezoelectricity, causing boundary layers in certain components of the strains and/or electric fields near the free surfaces., This work was supported by the Generalitat de Catalunya (“ICREA Academia” award for excellence in research to I.A., and Grants No. 2017-SGR-1278 and 2021-SGR-01049), the European Research Council (StG-679451 to I.A.), and the Spanish Ministry of Economy and Competitiveness (Grant PID2023-152533OB-I00 funded by MICIU/AEI/10.13039/501100011033/ERDF/EU, and Grant RTI2018-101662-B-I00). D.C. acknowledges the support of the Spanish Ministry of Universities through the Margarita Salas fellowship (European Union - NextGenerationEU). H.M. received the support of a fellowship from “la Caixa” Foundation (ID 100010434). The fellowship code is LCF/BQ/DI20/11780036. CIMNE is recipient of a Severo Ochoa Award of Excellence from the MINECO., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Topology optimization of flexoelectric metamaterials with apparent piezoelectricity

  • Greco, Francesco
  • Codony Gisbert, David
  • Mohammadi, Hossein
  • Fernández Méndez, Sonia
  • Arias Vicente, Irene
The flexoelectric effect, coupling polarization and strain gradient as well as strain and electric field gradients, is universal to dielectrics, but, as compared to piezoelectricity, it is more difficult to harness as it requires field gradients and it is a small-scale effect. This drawback can be overcome by suitably designing multiscale metamaterials made of a non-piezoelectric base material but exhibiting apparent piezoelectricity. We develop a theoretical and computational framework to perform topology optimization of the representative volume element of such metamaterials by accurately modeling the governing equations of flexoelectricity using a Cartesian B-spline method, describing geometry with a level set, and resorting to genetic algorithms for optimization. We consider a multi-objective optimization problem where area fraction competes with each one of the four fundamental piezoelectric functionalities (stress/strain sensor/actuator). We computationally obtain Pareto fronts, and discuss the different geometries depending on the apparent piezoelectric coefficient being optimized. Our results show that optimal material architectures strongly depend on the specific functional property being optimized, and that, except for stress actuators, optimal structures are low-area-fraction lattices. In general, we find competitive estimations of apparent piezoelectricity as compared to reference materials such as quartz and PZT ceramics. This opens the possibility to design devices for sensing, actuation and energy harvesting from a much wider, cheaper and effective class of materials., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Continuum and computational modeling of surface effects in flexoelectric materials

  • Dingle Palmer, Mònica
  • Arias Vicente, Irene
  • Codony Gisbert, David
In recent times, with the rise of nanoscale technologies, miniaturization of devices has prompted the need to study electromechanical phenomena at small scales. Most studies focus on the phenomena occurring at the bulk portion of the material, such as flexoelectricity, but neglect the effects that arise from the surfaces of the samples. Given the fact that, at such scales, surface-to-volume ratio is inherently large, surface effects cannot be ignored if the full and accurate description of the material’s response wants to be provided. In this work, we present a model that successfully integrates flexoelectricity and the effects of surfaces, and we properly derive the governing equations and boundary conditions for the boundary value problem. We also present a numerical approach in order to computationally solve it, converging at high-order optimal rates. In addition, we present an analytical 1D Euler–Bernoulli electromechanical beam model. Numerically, we find the presence of boundary layers in the transversal electric field across the beam thickness, which are not accounted for in the analytical 1D model. Finally, we find numerical solutions for geometrically-polarized flexoelectric lattice metamaterials, which have large area-to-volume ratios, giving rise to very relevant surface effects. This work emphasizes the importance of accounting for surface effects in modeling and design of flexoelectric devices, including geometrically-polarized metamaterials., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A C0 interior penalty Finite Element Method for flexoelectricity

  • Ventura, Jordi
  • Codony Gisbert, David
  • Fernández Méndez, Sonia
This is a post-peer-review, pre-copyedit version of an article published in Journal of scientific computing. The final authenticated version is available online at: http://dx.doi.org/10.1007/s10915-021-01613-w, We propose a C0 Interior Penalty Method (C0-IPM) for the computational modelling of flexoelectricity, with application also to strain gradient elasticity, as a simplified case. Standard high-order C0 finite element approximations, with nodal basis, are considered. The proposed C0-IPM formulation involves second derivatives in the interior of the elements, plus integrals on the mesh faces (sides in 2D), that impose C1 continuity of the displacement in weak form. The formulation is stable for large enough interior penalty parameter, which can be estimated solving an eigenvalue problem. The applicability and convergence of the method is demonstrated with 2D and 3D numerical examples., This work was supported by the European Research Council (StG679451 to Irene Arias), Agencia Estatal de Investigaci´on (RTI2018-101662-B-I00), Ministerio de Econom´ıa y Competitividad (CEX2018-000797-S) and Generalitat de Catalunya (2017- SGR-1278), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

C0-IPM with generalised periodicity and application to flexoelectricity-based 2D metamaterials

  • Balcells Quintana, Oscar
  • Codony Gisbert, David
  • Fernández Méndez, Sonia
The version of record is available online at: http://dx.doi.org/10.1007/s10915-022-01848-1, We propose a methodology to solve high-order PDE boundary value problems with generalised periodicity, in the framework of the C0 interior penalty method. The method is developed for the analysis of flexoelectricity- based metamaterial unit cells, formalising the corresponding problem statement and weak form, and giving details on the implementation of the local and macro conditions for generalised periodicity. Numerical examples demonstrate the high-order convergence of the method and its applicability in realistic problem settings., This work was supported by the European Research Council (StG-679451 to Irene Arias), Agencia Estatal de Investigación (RTI2018-101662-B-I00),Ministerio de Economía y Competitividad (CEX2018- 000797-S) and Generalitat de Catalunya (2017-SGR-1278), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A C0 Interior Penalty Finite Element method for flexoelectricity at finite deformations

  • Pérez Escudero, Sergi
  • Fernández Méndez, Sonia
© 2025 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC license (http://creativecommons.org/licenses/by-nc/4.0/)., The 4th-order partial differential equations modeling the flexoelectric effect at finite deformations are considered, accounting for direct and converse effects. Its numerical solution, using standard C0 Finite Elements, is carried out through the development of a C0 Interior Penalty method (C0 -IPM) with a Newton–Raphson nonlinear solver. The simulation of metamaterials by means of generalized periodicity conditions is also addressed within the C0 -IPM framework. The order of convergence of the method is assessed in a synthetic test, studying the effect of the penalty parameters in the accuracy of the scheme. The method is also applied to the solution of a cantilever beam problem, and to the simulation of metamaterials at large deformations., This work was supported by the Agència de Gestió d’Ajuts Universitaris i de Recerca (training grant FI-AGAUR 2022 to Sergi Pérez-Escudero), Ministerio de Ciencia, Innovación y Universidades (PID2023-152533OB-I00 funded by MICIU/AEI/10.13039/501100011033/ERDF/EU, and RTI2018-101662-B-I00), and Generalitat de Catalunya (2021-SGR-01049)., Peer Reviewed, Postprint (published version)
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Switchable tribology of ferroelectrics

  • Cho, Seongwoo|||0000-0002-3000-4251
  • Gaponenko, Iaroslav|||0000-0002-9694-7033
  • Cordero Edwards, Kumara|||0000-0003-3721-7863
  • Barceló-Mercader, Jordi
  • Arias, Irene|||0000-0002-6761-3499
  • Kim, Daeho
  • Lichtensteiger, Céline|||0000-0002-9796-8071
  • Yeom, Jiwon
  • Musy, Loïc|||0000-0002-7741-6763
  • Kim, Hyunji
  • Han, Seung Min
  • Catalan, Gustau|||0000-0003-0214-4828
  • Paruch, Patrycja
  • Hong, Seungbum|||0000-0002-2667-1983
Switchable tribological properties of ferroelectrics offer an alternative route to visualize and control ferroelectric domains. Here, we observe the switchable friction and wear behavior of ferroelectrics using a nanoscale scanning probe-down domains have lower friction coefficients and show slower wear rates than up domains and can be used as smart masks. This asymmetry is enabled by flexoelectrically coupled polarization in the up and down domains under a sufficiently high contact force. Moreover, we determine that this polarization-sensitive tribological asymmetry is widely applicable across various ferroelectrics with different chemical compositions and crystalline symmetry. Finally, using this switchable tribology and multi-pass patterning with a domain-based dynamic smart mask, we demonstrate three-dimensional nanostructuring exploiting the asymmetric wear rates of up and down domains, which can, furthermore, be scaled up to technologically relevant (mm-cm) size. These findings demonstrate that ferroelectrics are electrically tunable tribological materials at the nanoscale for versatile applications.