Pasar al contenido principal

TECNOLOGIAS DE FIBRA OPTICA PARA LA SEGURIDAD CIVIL

TEC2012-37958-C02-02

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Relative intensity noise transfer reduction in raman-assisted BOTDA systems

  • Angulo Vinuesa, Xabier
  • Bacquet, D.
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Szriftgiser, P.
  • González Herráez, Miguel|||0000-0003-2555-2971
Raman-assistance (RA) has been identified as a promising technique to extend the measurement range of Brillouin optical time-domain analysis (BOTDA)-based distributed sensors. Unfortunately, Raman amplification introduces a great amount of relative intensity noise (RIN) to the detected low-frequency probe wave. This RIN transfer problem has been widely identified as a major limitation in RA-BOTDA. In vector BOTDA (VBOTDA), the detected signal is transferred to a high-frequency carrier where the Raman RIN transfer turns out to be much less harmful. In addition, a VBOTDA can also provide information about the phase-shift induced by the local stimulated Brillouin scattering gain curve, paving the way for dynamic measurements. In this letter, we demonstrate, for the first time to our knowledge, the RA in a VBOTDA obtaining gain and phase measurements. Our results show a significant reduction of the RIN transfer effect in RA-VBOTDA compared with standard RA-BOTDA, making this type of scheme particularly interesting for long-range and dynamic distributed sensing., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Modulation instability-induced fading in phase-sensitive optical time-domain reflectometry

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Salgado, P.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
Phase-sensitive optical time-domain reflectometry (φOTDR) is a simple and effective tool allowing the distributed monitoring of vibrations along single-mode fibers. We show in this Letter that modulation instability (MI) can induce a position-dependent signal fading in long-range φOTDR over conventional optical fibers. This fading leads to a complete masking of the interference signal recorded at certain positions and therefore to a sensitivity loss at these positions. We illustrate this effect both theoretically and experimentally. While this effect is detrimental in the context of distributed vibration analysis using φOTDR, we also believe that the technique provides a clear and insightful way to evidence the Fermi-Pasta-Ulam recurrence associated with the MI process., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Simple Method for the Elimination of Polarization Noise in BOTDA Using Balanced Detection and Orthogonal Probe Sidebands

  • López Gil, Alexia Inés
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
Polarization noise arises in Brillouin optical timedomain analysis due to the strong polarization sensitivity of stimulated Brillouin scattering. To avoid this noise, it turns out to be indispensable to perform some kind of polarization scrambling, either in the pump pulse, the probe signal or both. This is usually achieved using polarization scrambling/switching systems, which, being mechanical, tend to be not as robust as it would be desirable. In this paper, we propose a completely passive system,with no moving parts, to eliminate polarization noise in a BOTDA. It is based on the use of passive depolarization of the pump pulse together with balanced detection among orthogonally polarized Stokes and anti-Stokes bands of the probe signal. The setup requires no alignment readjustment over time and provides a performance similar to a conventional BOTDA using scrambler., Ministerio de Economía y Competitividad, Comunidad de Madrid, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Reaching the ultimate performance limit given by non-local effects in BOTDA sensors

  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Yang, Z.
  • Soto Hernández, Marcelo Alfonso
  • Angulo Vinuesa, Xabier
  • Martín López, Sonia|||0000-0001-5203-6206
  • Thévenaz, Luc
  • González Herráez, Miguel|||0000-0003-2555-2971
24th International Conference on Optical Fibre Sensors, 96343Y, Curitiba, Brazil, September 28, 2015., Non-local effects have been traditionally identified as one of the most limiting factors of the performance of Brillouin optical time-domain analyzers. These phenomena, directly linked with the energy gained/lost by the pump pulse, limit the probe power and ultimately the SNR of the system. Several solutions have been proposed, although none offers the possibility to increase the probe power until its limit, the onset of amplified spontaneous Brillouin scattering. In this work, we propose a technique that avoids non-local effects and permits to set the probe power at its maximum, reaching a 100 km sensing distance with 2 meter resolution., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Raman-assisted Vector Brillouin Optical Time Domain Analysis

  • Angulo Vinuesa, Xabier
  • Bacquet, D.
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Szriftgiser, P.
  • González Herráez, Miguel|||0000-0003-2555-2971
Raman-assistance (RA) has become a promising technique to enhance the sensing range of standard Brillouin Optical Time Domain Analysis (BOTDA) fiber sensors due to its ability to amplify in a distributed way all the interacting signals within the fiber. Unfortunately, Raman amplification introduces a great amount of Relative Intensity Noise (RIN) to the detected low-frequency probe wave. This RIN transfer problem has been widely identified as a major limitation in RABOTDA. In Vector Brillouin Optical Time Domain Analysis (VBOTDA) the detected signal is transferred to a highfrequency carrier where the Raman RIN transfer turns out to be much less harmful. In this work we demonstrate, for the first time to our knowledge, Raman-assistance in a VBOTDA. Our results show significant reduction of the RIN transfer effect in RA-VBOTDA compared to standard RA-BOTDA, making this type of scheme particularly interesting for long range distributed sensing., European Commission, Ministerio de Economía y Competividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Limits of BOTDA Range Extension Techniques

  • Angulo Vinuesa, Xabier
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • López Gil, Alexia Inés
  • Ania Castañón, Juan Diego
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
Brillouin-based temperature and strain sensors have attracted great attention of both the academic and industrial sectors in the past few decades due to their ability to perform distributed measurements. Particularly, Brillouin Optical Time Domain Analysis (BOTDA) systems have been applied in many different scenarios, proving particularly useful in those requiring especially wide coverage ranging extremely long distances, such as in civil structure monitoring, energy transportation or environmental applications. The extension of the measuring range in these sensors has therefore become one of the main areas of research and development around BOTDA. To do so, it is necessary to increase the Signal to Noise Ratio (SNR) of the retrieved signal. So far, several techniques have been applied in order to achieve this goal, such as pre-amplification before detection, pulse coding or Raman amplification. Here, we analyze these techniques in terms of their performance limits and provide guidelines that can assist in finding out which is the best configuration to break current range limitations. Our analysis is based on physical arguments as well as current literature results., European Commission, Ministerio de Economía y Competitividad, Universidad de Alcalá, Ministerio de Ciencia e Innovación, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Strong Cancellation of RIN Transfer in a Raman-Assisted BOTDA Using Balanced Detection

  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • López Gil, Alexia Inés
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
Raman assistance is one of the most interesting routes toward extending the range of Brillouin optical timedomain analysis (BOTDA) systems. Unfortunately, the use of Raman amplification normally entails an important relative intensity noise (RIN) transfer toward the probe wave, which severely limits this approach. In this letter, we show that the RIN transfer problem can be effectively avoided using a slightly modified scheme comprising a dual-sideband modulated probe and balanced detection. Our measurements clearly indicate a nearly complete cancellation of the RIN noise in the detected trace signal. The use of balanced detection in our Raman-assisted BOTDA setup implies a fivefold increase in figure of merit compared with the same setup using conventional detection., European Commission, Ministerio de Economía y Competitividad
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Distributed vibration sensing over 125 km with enhanced SNR using ΦOTDR over a URFL cavity

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Ania Castañón, Juan Diego
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
We describe the use of a phase-sensitive optical time domain reflectometer (ΦOTDR) over an ultra-long Raman fiber laser cavity allowing fully distributed detection of vibrations over 125 km. Compared to a first-order Raman-assisted ΦOTDR, this scheme shows an enhanced signal-to-noise ratio (SNR). This is due to the fact that the relative intensity noise introduced by the Raman amplification is mostly transferred to a lower frequency range, where the balanced detection implemented in the setup provides better suppression of the common-mode noise. The sensor was able to measure vibrations of up to 380 Hz (limit set by the time of flight of light pulses) in a distance of 125 km with a resolution of 10 m and an average SNR of 8 dB with no postprocessing. This implies a >3 dB improvement in SNR over a first-order Raman-assisted setup with similar characteristics, Ministerio de Economía y Competitividad, Ministerio de Ciencia e Innovación, Comunidad de Madrid, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Phase-sensitive optical time domain reflectometer assisted by first-order raman amplification for distributed vibration sensing over >100 km

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Filograno, M. L.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
In this study, the authors present an experimental and theoretical description of the use of first order Raman amplification to improve the performance of a Phase-sensitive optical time domain reflectometer (φ OTDR) when used for vibration measurements over very long distances. A special emphasis is given to the noise which is carefully characterized and minimized along the setup. A semiconductor optical amplifier and an optical switch are used to greatly decrease the intra-band coherent noise of the setup and balanced detection is used to minimize the effects of RIN transferred from the Raman pumps. The sensor was able to detect vibrations of up to 250 Hz (close to the limits set by the time of flight of light pulses) with a resolution of 10 m in a range of 125 km. To achieve the above performance, no post-processing was required in the φOTDR signal. The evolution of the φOTDR signal along the fiber is also shown to have a good agreement with the theoretical model., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Coherent noise reduction in high visibility phase-sensitive optical time domain reflectometer for distributed sensing of ultrasonic waves

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Filograno, M. L.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
Phase-sensitive optical time domain reflectometry (\phi \hbox{OTDR}) is a simple and effective tool allowing the distributed monitoring of vibrations along single-mode fibers. Up to now, \phi {\rm OTDRs} have been used mostly for the measurement of sub-kHz vibrations, normally in the context of intrusion sensing. In this paper, the authors present an experimental and theoretical description of a high-visibility \phi {\rm OTDR} and its performance when used for ultrasonic vibration measurements. The use of a semiconductor optical amplifier in the setup allows to suppress coherent noise and also to improve the spectral response of the pump pulses. These two advantages greatly decrease the detected intra-band noise thus allowing frequency measurements in the limits set by the time of flight of the light pulses while maintaining the simplicity of the scheme, as no post-processing, extremely high coherence lasers or coherent detection methods are required. The sensor was able to measure vibrations of up to 39.5 kHz with a resolution of 5 m over a range which could go up to 1.25 km. This is the first time to our knowledge that a fully distributed measurement of ultrasonic waves was achieved. The statistical behavior of the system was also described theoretically and characterized experimentally, European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Comparison of the use of first and second-order Raman amplification to assist a phase-sensitive optical time domain reflectometer in distributed vibration sensing over 125 km

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Filograno, M. L.
  • Corredera Guillén, Pedro
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
We report on the use of second-order Raman amplification to assist a phase-sensitive optical time domain reflectometer ( φOTDR ) used for vibration measurements over very long distances. The sensor was able to measure vibrations of up to 380 Hz (limit set by the time of flight of light pulses) in a distance of 125 km with a resolution of 10 m and no postprocessing. Balanced detection is used to reduce the relative intensity noise. A comparison with a sensor using first-order Raman amplification under similar conditions is presented and a clear improvement of performance is demonstrated., Ministerio de Economía y Competitividad, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Non-local effects in dual-probe-sideband Brillouin optical time domain analysis

  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Angulo Vinuesa, Xabier
  • López Gil, Alexia Inés
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
According to recent models, non-local effects in dual-probesideband Brillouin Optical Time Domain Analysis (BOTDA) systems should be essentially negligible whenever the probe power is below the Stimulated Brillouin Scattering (SBS) threshold. This paper shows that actually there appear non-local effects in this type of systems before the SBS threshold. To explain these effects it is necessary to take into account a full spectral description of the SBS process. The pump pulse experiences a frequency-dependent spectral deformation that affects the readout process differently in the gain and loss configurations. This paper provides a simple analytical model of this phenomenon, which is validated against compelling experimental data, showing good agreement. The main conclusion of our study is that the measurements in gain configuration are more robust to this non-local effect than the loss configuration. Experimental and theoretical results show that, for a total probe wave power of ~1 mW (500 μW on each sideband), there is an up-shifting of ~1 MHz in the Brillouin Frequency Shift (BFS) retrieved from the Brillouin Loss Spectrum, whereas the BFS extracted from the measured Brillouin Gain Spectrum is up-shifted only ~0.6 MHz. These results are of particular interest for manufacturers of longrange BOTDA systems., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

III-nitride-based waveguides for ultrafast all-optical signal processing at 1.55 μm

  • Monteagudo Lerma, Laura
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
  • Valdueza Felip, Sirona|||0000-0003-1817-5354
  • Jiménez Rodríguez, Marco
  • Monroy, Eva
  • Postigo, P.A.
  • Corredera Guillén, Pedro
  • González Herráez, Miguel|||0000-0003-2555-2971
We present an overview of the recently developed III-nitride-based optical waveguides for application in ultrafast signal processing at telecom wavelengths. We focus on different active and passive optical devices for further implementation within all-optical integrated circuits. Optical waveguides based on GaN/AlN quantum dots have been demonstrated to act as saturable absorbers requiring ∼3 pJ of input pulse energy to reach +3 dB transmittance contrast for TM-polarized light. On the contrary, sputtered-InN-based devices show -3 dB transmittance contrast associated to two-photon absorption for input pulse energies of ∼1 pJ, making them suitable to act as highly-efficient reverse saturable absorbers. Finally, the passive optical nature of waveguides based on sputtered AlN at 1.55 μm makes them suitable for further connections between different III-nitride-based active devices. Similar to the development of electronic integrated circuits, photonic integrated circuits are being widely investigated to implement active and passive optical functions in different material platforms. III-nitrides on sapphire substrates emerge as efficient all-optical solutions within the photonic integrated circuit presenting high nonlinear behavior and ultrafast response. These heterostructures make possible the full exploitation of the optical fiber bandwidth which is highly required in today's globalized world. © 2015 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim., Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá, European Commission