Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Low-Power Operation in a Silicon Switch Based on an Asymmetric Mach Zehnder Interferometer

  • Sánchez Diana, Luis David
  • Lechago Buendía, Sergio
  • Brimont, Antoine Christian Jacques
  • Griol Barres, Amadeu
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] Mach Zehnder interferometer (MZI) structures are widely used as optical switches in photonic integrated circuits. However, power consumption is still the key parameter to make such devices practical in the silicon platform, particularly for those based on the thermo-optic effect. A new approach to significantly decrease the power consumption of a silicon switch based on an asymmetric MZI, together with an optimum selection of the operation wavelengths, is proposed. A power consumption reduction up to 50% is experimentally demonstrated in agreement with simulation results., This work was supported by TEC2012-38540 LEOMIS and NANOMET PLUS-Conselleria d'Educacio, Cultura i EsportPROMETEOII/2014/034. The work of L. Sanchez was supported by Generalitat Valenciana in the context of the VALi+d program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Low-Loss and Compact Silicon Rib Waveguide Bends

  • Brimont, Antoine Christian Jacques
  • Hu, X.
  • Cueff, Sébastien
  • Rojo-Romeo, Pedro
  • Saint Girons, Guillaume
  • Zanzi, Andrea
  • Orobtchouk, Regis
  • Griol Barres, Amadeu
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] Waveguide bends support intrinsically leaky propagation modes due to unavoidable radiation losses. It is known that the losses of deep-etched/strip waveguide bends increase inevitably for decreasing radius. Here, we theoretically and experimentally demonstrate that this result is not directly applicable to shallow-etched/rib waveguide bends. Indeed, we show that the total losses caused by the bends reach a local minimum value for a certain range of compact radii and rib waveguide dimensions. Specifically, we predicted the minimum intrinsic losses < 0.1 dB/90 degrees turn within the range of 25-30 mu m bend radii in a 220 nm-thick and 400 nm-wide silicon rib waveguide with 70 nm etching depth. This unexpected outcome, confirmed by experimental evidence, is due to the opposite evolution of radiation (bending) losses and losses caused by the coupling to lateral slab modes (slab leakage) as a function of the bend radius, hence creating an optimum loss region. This result may have important implications for the design of compact and low-loss silicon nanophotonic devices., This work was supported in part by the European STREP Program under Grant FP7-ICT-2013-11-619456-SITOGA and Grant FP7-ICT-2012-10-318240 PhoxTroT and in part by LEOMIS under Grant TEC2012-38540. (Corresponding author: Regis Orobtchouk.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electro-Optical Modulation Based on Pockels Effect in BaTiO3 With a Multi-Domain Structure

  • Castera, Pau
  • Gutiérrez Campo, Ana María
  • Tulli, Domenico
  • Cueff, Sébastien
  • Orobtchouk, Regis
  • Rojo Romeo, Pedro
  • Saint-Girons, Guillaume
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] The influence of an in-plane multi-domain structure in BaTiO3 films grown on SrTiO3/Si buffers for highly efficient electro-optic modulation has been analyzed. The modulation performance can be significantly enhanced by rotating a certain angle, the optical waveguide, with respect to the BaTiO3 crystallographic axes. A robust electro-optical performance against variations in the domain structure as well as the lowest V-pi voltage can be achieved by using the rotation angles between 35 degrees and 55 degrees. Our calculations show that Vp voltages below 1.7 V for a modulation length of 2 mm can be obtained by means of a CMOS compatible hybrid silicon/BaTiO3 waveguide structure., This work was supported by the European Commission under Grant FP7-ICT-2013-11-619456 SITOGA. The work of P. Sanchis was supported in part by GVA under Grant PROMETEOII/2014/034 and in part by the Ministerio de Economia y Competitividad under Grant TEC2012-38540 LEOMIS.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A photonic microwave filter based on an asymmetric silicon Mach-Zehnder modulator

  • Gutiérrez Campo, Ana María
  • Brimont, Antoine Christian Jacques
  • Thomson, David J.
  • Gardes, Frédéric Y.
  • Reed, Graham T.
  • Fédéli, Jean Marc
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
  • Vidal, Borja|||0000-0002-0942-3259
[EN] A new approach for implementing an integrable photonic microwave filter based on exploiting the asymmetry of a CMOS-compatible silicon Mach-Zehnder modulator is demonstrated. The strong dependence of the modulator response with wavelength is exploited for achieving positive and negative taps and, therefore, a fully reconfigurable filter, without the complexity of previous approaches. Two filter responses with two and three taps are experimentally demonstrated, showing the proof-of-principle for frequencies up to 10 GHz and thus going one step further toward a full integration of the complete filter device in the CMOS-compatible silicon photonics platform. © 2009-2012 IEEE., Manuscript received May 16, 2013; revised June 12, 2013; accepted June 13, 2013. Date of publication June 18, 2013; date of current version June 26, 2013. This work was supported by the European Commission through project HELIOS (Photonics Electronics functional Integration on CMOS) under Grant FP7-224312. The work of P. Sanchis was supported by funding from TEC2012-38540 LEOMIS, TEC2008-06333 SINADEC, and PROMETEO-2010-087. The works of D. J. Thomson, F. Y. Gardes, and G. T. Reed were supported by the UK EPSRC funding body under the grant BUK Silicon Photonics.[Corresponding author: P. Sanchis (e-mail: pabsanki@ntc.upv.es).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High performace silicon 2x2 optical switch based on a thermo-optically tunable multimode interference coupler and efficient electrodes

  • Rosa Escutia, Álvaro
  • Gutiérrez Campo, Ana María
  • Brimont, Antoine Christian Jacques
  • Griol Barres, Amadeu
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
Optical switches based on tunable multimode interference (MMI) couplers can simultaneously reduce the footprint and increase the tolerance against fabrication deviations. Here, a compact 2x2 silicon switch based on a thermo-optically tunable MMI structure with a footprint of only 0.005mm2 is proposed and demonstrated. The MMI structure has been optimized using a silica trench acting as a thermal isolator without introducing any substantial loss penalty or crosstalk degradation. Furthermore, the electrodes performance have significantly been improved via engineering the heater geometry and using two metallization steps. Thereby, a drastic power consumption reduction of around 90% has been demonstrated yielding to values as low as 24.9 mW. Furthermore, very fast switching times of only 1.19 μs have also been achieved., Financial support from LEOMIS TEC2012-38540 and PROMETEOII/2014/034 projects is acknowledged. Alvaro Rosa also acknowledges the Spanish Ministry of Economy and Competitiveness for funding his grant. The authors also would like to thank the Electronic Microscopy Department at UPV for taking the SEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of BaTiO3 ferroelectric orientation for electro-optic modulation on silicon

  • Castera Molada, Pau
  • Tulli, Domenico
  • Gutiérrez Campo, Ana María
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] The influence of BaTiO3 ferroelectric domain orientations for high efficiency electro-optic modulation has been thoroughly analyzed. The Mach-Zehnder modulator structure is based on a CMOS compatible silicon/BaTiO3/silicon slot waveguide that supports both TE and TM polarizations whereas the Pockels effect is exploited by the application of a horizontal electric field with lateral electrodes placed on top of the BaTiO3 layer. The influence of the waveguide parameters has been optimized for each configuration and the lowest V&#960; voltage combined with low losses has been determined. A V&#960;L as low as 0.27 V·cm has been obtained for a-axis oriented BaTiO3 and TE polarization by rotating the waveguide structure to an optimum angle., This work was supported by the European Commission under project FP7-ICT-2013-11-619456 SITOGA. Financial support from TEC2012-38540 LEOMIS is also acknowledged. We also acknowledge Stefan Abel and Sebastien Cueff for their helpful comments.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Luminescence properties of Ce3+ and Tb3+ co-doped SiOxNy thin films: Prospects for color tunability in silicon-based hosts

  • Ramirez, J. M.
  • Ruiz-Caridad, A.
  • Wojcik, J.
  • Gutiérrez Campo, Ana María
  • Estrade, S.
  • Peiro, F.
  • Mascher, P.
  • Garrido, B.
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
In this work, the role of the nitrogen content, the annealing temperature, and the sample morphology on the luminescence properties of Ce3+ and Tb3+ co-doped SiOxNy thin films has been investigated. An increasing nitrogen atomic percentage has been incorporated in the host matrix by gradually replacing oxygen with nitrogen during fabrication while maintaining the Si content unaltered, obtaining a sequential variation in the film composition from nearly stoichiometric SiO2 to SiOxNy. The study of rare earth doped single layers has allowed us to identify the parameters that yield an optimum optical performance from Ce3+ and Tb3+ ions. Ce3+ ions proved to be highly sensitive to the annealing temperature and the nitrogen content, showing strong PL emission for relatively low nitrogen contents (from 0 to 20%) and moderate annealing temperatures (800-1000 degrees C) or under high temperature annealing (1180 degrees C). Tb3+ ions, on the other hand, displayed a mild dependence on those film parameters. Rare earth co-doping has also been investigated by comparing the luminescence properties of three different approaches: (i) a Ce3+ and Tb3+ co-doped SiOxNy single layer, (ii) a bilayer composed of two SiOxNy single layers doped with either Ce3+ or Tb3+ ions, and (iii) a multilayer composed of a series of either Tb3+ or Ce3+-doped SiOxNy thin films with interleaved SiO2 spacers. Bright green emission and efficient energy transfer from either Ce3+ ions or Ce silicates to Tb3+ ions has been observed in the co-doped single layer as a consequence of the strong ion-ion interaction. On the other hand, independent luminescence from Ce3+ and Tb3+ ions has been observed in the Ce3+ and Tb3+ co-doped bilayer and multilayer, providing a good scenario to develop light emitting devices with wide color tunability by varying the number of deposited films that contain each rare earth dopant. Moreover, the optoelectronic properties of Ce3+-and/or Tb3+-doped thin films have been studied by depositing transparent conductive electrodes over selected samples. An electroluminescence signal according to the rare earth transitions is obtained in all cases, validating the excitation of Ce3+ and Tb3+ ions upon electron injection. Also, the main charge transport of injected electrons has been evaluated and correlated with the layer stoichiometry. Finally, a simple reliability test has allowed disclosing the origin of the early breakdown of test devices, attributed to the excessive joule heating at filament currents that occur around a region close to the polarization point. (C) 2016 AIP Publishing LLC., This research was supported by the Spanish Ministry of Science and Innovation (TEC2012-38540-C02-01). RBS characterization was performed in the Tandetron Accelerator Laboratory at Western University in London, ON (Canada). TEM characterization was carried out in the Science and Technical Centers (CCiT) of the University of Barcelona. In Canada, this work was supported by the Natural Sciences and Engineering Research Council (NSERC) under the Discovery Grants program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis and design optimization of a hybrid VO2/Silicon 2x2 microring switch

  • Sánchez Diana, Luis David
  • Lechago-Buendia, Sergio
  • Gutiérrez Campo, Ana María
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
The metal-to-insulator transition (MIT) property of vanadium dioxide (VO2) has been recently used in several application fields like plasmonics, sensing, metamaterials and optical modulation. Due to the MIT nature, VO2 allows a huge change in its complex refractive index that can be electro-optically controlled. In this work, the analysis and design optimization of a 2x2 microring switch based on a hybrid VO2/silicon waveguide structure is addressed. Switching is achieved by exploiting the change in both absorption loss and phase shift that occurs in the VO2 when changing from the insulating to the metallic state. The device is optimized to minimize insertion losses and crosstalk. An active length of only 2.8µm is required to achieve a data throughput rate higher than 500Gbps at a single optical wavelength., This work was also supported by LEOMIS (TEC2012-38540) and NANOMET PLUS-Conselleria d'Educacio, Cultura i Esport (PROMETEOII/2014/034). The work of L. Sanchez was supported by the Generalitat Valenciana in the context of the VALi+d program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Compact focusing grating couplers for silicon horizontal slot waveguides

  • Larrea-Luzuriaga, Roberto Alejandro
  • Gutiérrez Campo, Ana María
  • Ramirez, J. M.
  • Garrido, B.
  • Hurtado Montañés, Juan|||0000-0002-4870-7641
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
In this Letter, we present the design, simulation (2D and 3D), fabrication, and experimental characterization of compact and fully etched focusing gratings for a horizontal slot waveguide based on a silicon nitride layer sandwiched between amorphous silicon and a silicon-on-insulator. The measured coupling losses are about 4 dB with a 3 dB bandwidth of 38 nm. The fully etched configuration allows the fabrication in a single lithography step., Ministerio de Economia y Competitividad (MINECO) (TEC2012-38540-C02-02, TEC2016-76849-C2-2-R); Generalitat Valenciana (NANOMET PLUS -PROMETEOII/2014/034).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultra-compact TE and TM pass polarizers based on vanadium dioxide on silicon

  • Sánchez Diana, Luis David
  • Lechago Buendía, Sergio
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] Vanadium dioxide (VO2) is a metal-insulator transition (MIT) oxide recently used in plasmonics, metamaterials, and reconfigurable photonics. Because of the MIT, VO2 shows great change in its refractive index allowing for ultra-compact devices with low power consumption. We theoretically demonstrate a transverse electric (TE) and a transverse magnetic (TM) pass polarizer with an ultra-compact length of only 1 &#956;m and tunable using the MIT of the VO2. During the insulating phase, both devices exhibit insertion losses below 2 dB at 1550 nm. Changing to the metallic phase, the unwanted polarization is attenuated above 15 dB while insertion losses are kept below 3 dB. Broadband operation over a range of 60 nm is also achieved., This work was supported by the European Commission under project FP7-ICT-2013-11-619456 SITOGA. Financial support from TEC2012-38540 LEOMIS is also acknowledged. L. Sanchez also acknowledges the Generalitat Valenciana for funding his grant in the context of the VALi+d program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Resistive switching and charge transport mechanisms in ITO/ZnO/p-Si devices

  • Blázquez, O.
  • Frieiro, J.L.
  • López-Vidrier, J.
  • Guillaume, C.
  • Portier, X.
  • Labbé, C.
  • Hernández, S.
  • Garrido, B.
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] The resistive switching properties of ITO/ZnO/p-Si devices have been studied, which present well-defined resistance states with more than five orders of magnitude difference in current. Both the high resistance state (HRS) and the low resistance state (LRS) were induced by either sweeping or pulsing the voltage, observing some differences in the HRS. Finally, the charge transport mechanisms dominating the pristine, HRS, and LRS states have been analyzed in depth, and the obtained structural parameters suggest a partial re-oxidation of the conductive nanofilaments and a reduction of the effective conductive area., This work was financially supported by the Spanish Ministry of Economy and Competitiveness (Project Nos. TEC2012-38540-C02-01 and TEC2016-76849-C2-1-R). O.B. also acknowledges the subprogram "Ayudas para Contratos Predoctorales para la Formacion de Doctores" of the Spanish Ministry of Economy and Competitiveness for economical support. X.P., C.L., and C.G. are grateful to C. Frilay for his expertise in the maintenance of the sputtering kit used for the growth of the ZnO films.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Broadband 8 micrometers long hybrid silicon-plasmonic transverse magnetic-transverse electric converter with losses below 2 dB

  • Sánchez Diana, Luis David
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
A novel ultracompact (8 mu m length) hybrid silicon-plasmonic TM-TE converter is reported. The conversion is achieved during a partial power coupling between a waveguide and a hybrid plasmonic parallel waveguide. The impact of different types of metals is also analyzed. At a wavelength of 1.55 mu m, the device has an extinction ratio (ER) of 27.6 dB and insertion loss (IL) of 1.75 dB. Furthermore, an optical bandwidth as large as 100 nm is achieved with ERs higher than 25 dB and ILs below 2 dB. (C) 2013 Optical Society of America, The authors acknowledge funding from TEC2012-38540 LEOMIS and PROMETEO-2010-087. L. Sanchez also acknowledges the Generalitat Valenciana for funding his grant in the context of the VALi+d program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Compact and low-loss asymmetrical multimode interference splitter for power monitoring applications

  • Zanzi, Andrea
  • Brimont, Antoine Christian Jacques
  • Griol Barres, Amadeu
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
  • Martí Sendra, Javier
[EN] This Letter presents a compact and low-loss 1 x 2 asymmetrical multimode interference (A-MMI) splitter in rib geometry for on-chip power monitoring at 1.55 mu m, where a given alteration of the component cavity determines arbitrary values of the output power splitting ratios. The device shows reduced losses (similar to 0.4-0.8 dB) and robustness across a 40 nm optical bandwidth (1540-1580 nm). (C) 2016 Optical Society of America, 7th European community Framework Programme (FP7-ICT-318240); Spanish Ministry of Science and Technology (TEC2012-38540).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optical phase characterization of photonic integrated devices

  • Matres Abril, Joaquín
  • Ballesteros García, Guillem
  • Mas Gómez, Sara María
  • Brimont, Antoine Christian Jacques
  • Oton Nieto, Claudio José
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
  • Martí Sendra, Javier
We propose a relatively simple experimental setup, capable of accurately characterizing the optical phase response of an integrated photonic circuit. The setup is based on a phase-noise reduction scheme using an external heterodyne Mach Zehnder interferometer. In particular, we characterize the phase response of different silicon photonic components: under- and over-coupled ring resonators, and a slow-light corrugated waveguide., This work was supported by the Spanish Ministry of Science and Innovation through SINADEC (TEC2008-06333), LEOMIS (TEC2012-38540), and PROMETEO/2010/087 NANOFOTONICA Contracts, Universidad Politecnica de Valencia for PAID2011/1914 and Joaquin Matres FPI Doctoral Grant, and Transatlantic partnership for Excellence in Engineering funded by EU Commission under the Erasmus Mundus Action 2 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analytical model for calculating the nonlinear distortion in silicon-based electro-optic Mach-Zehnder modulators

  • Gutiérrez Campo, Ana María
  • Brimont, Antoine Christian Jacques
  • Herrera Llorente, Javier
  • Aamer, Mariam
  • Thomson, Dave J.
  • Gardes, Frederic Y.
  • Reed, Graham T.
  • Fedeli, Jean-Marc
  • Sanchis Kilders, Pablo|||0000-0003-2984-4218
[EN] In this study, an analytical model for calculating the nonlinear harmonic/intermodulation distortion for RF signals in silicon-based electro-optic modulators is investigated by considering the nonlinearity on the effective index change curve with the operation point and the device structure simultaneously. Distortion expressions are obtained and theoretical results are presented showing that optimal modulator parameters can be found to linearize it. Moreover, the harmonic distortion of a 1 mm silicon-based asymmetric MZI is RF characterized and used to corroborate the theoretical results. Based on the present model, the nonlinear distortion in terms of bias voltage or operating wavelength is calculated and validated by comparing with the experimental data, showing a good agreement between measurements and theory. Analog photonic link quality parameter like carrier-todistortion is one of the parameters that can be found with that model. Finally, the modulation depth is measured to assure that no over-modulation is produced., This work was supported by the funding from the European Commission under project HELIOS (pHotonics Electronics functional Integration on CMOS), FP7-224312. The work of P. Sanchis and J.-M. Fedeli was supported by the funding funding from TEC2012-38540 LEOMIS, TEC2008-06333 SINADEC, and PROMETEO-2010-087. The work of F. Y. Gardes, D. J. Thomson and G. T. Reed was supported by funding received from the UK EPSRC funding body under the grant "UK Silicon Photonics."