Pasar al contenido principal

APROXIMACION HOLISTICA A LA ALIMENTACION DE LOS NODOS DEL INTERNET DE LAS COSAS

TEC2016-76991-P

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Experimental characterization of the energy consumption of ADC embedded into microcontrollers operating in low power

  • Reverter Cubarsí, Ferran
  • Gasulla Forner, Manuel
This work aims to experimentally characterize the energy consumption of analog-to-digital converters (ADC) embedded into microcontroller units (MCU) operating in low power for autonomous sensor applications. The study is carried out at low and high operating frequencies, and for different numbers of conversion bits. In addition, this work not only takes into account the energy to do the conversion, but also the wake-up energy, which is implicit to any conversion performed by an embedded ADC. The contribution of this wake-up energy can be quite significant, especially when the conversion is performed at high frequency. Experimental tests have been done using a commercial low-power MCU (MSP430FR5969 from Texas Instruments) that includes a 12- bit ADC., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Effect of the sampling parameters in FOCV-MPPT circuits for fast-varying EH sources

  • Carandell Widmer, Matias
  • Holmes, Andrew S.
  • Toma, Daniel
  • Río Fernández, Joaquín del
  • Gasulla Forner, Manuel
© 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The fractional open circuit voltage (FOCV) method is extensively used in low-power energy harvesting (EH) sources to extract maximum power. For fast-varying EH sources a fast sampling rate is required. This work theoretically analyzes the influence of the sampling time and period on the harvested power of sinusoidal EH sources. In addition, the circuit limitations to achieve a fast sampling rate are presented and circuits to deal with them proposed and implemented. Furthermore, one of the circuits is based on a novel pseudo-FOCV method and achieves the fastest sampling rate. Experimental tests are performed with a 2 Hz, 1 V to 3 V sinusoidal source having an output resistance of 127 ¿, and the results are shown to agree with theoretical predictions. It is shown that 1) the harvested power increases with the sampling rate when the sampling time is negligible (sampling 15 times faster than the source frequency extracts around 99 % of the maximum), and 2) for fixed sampling times there is an optimum sampling rate where the harvested power is maximum. The first result is generic and valid for methods other than the FOCV. Tests were also performed with a small-scale wave energy converter placed in a linear shaker emulating a sea environment. Harvested power increases by 25 % with respect using a commercial FOCV unit with a low sampling rate., This work was supported by the project MELOA from the European Commission’s Horizon 2020 research and Innovation program under Grant Agreement No. 776280 and by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under project TEC2016-76991-P. The first author has a grant from the Secretariat of Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia on the FI program (ref. BDNS 362582)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Differential inductive sensor-to-microcontroller interface circuit

  • Kokolanski, Zivko
  • Gasulla Forner, Manuel
  • Reverter Cubarsí, Ferran
This paper proposes a low-cost interface circuit for differential inductive sensors where the sensor is directly connected to a microcontroller unit (MCU) without any active intermediate electronics in between. The timer embedded into the MCU is employed to measure the discharging or charging time interval of two passive RL networks formed by each sensor coil and an external resistor. Two topologies of the circuit are presented, evaluating their advantages and drawbacks. One of the topologies is implemented using a low-cost 8-bit MCU (Atmel ATmega328P) and its transfer characteristics is evaluated when measuring a commercial displacement inductive sensor. Experimental results show that, in a range of ±25 mm, the non-linearity error is smaller than 1%, and the resolution is 9 bits for an overall measuring time of a few milliseconds., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Experimental characterization of off-the-shelf LEDs as photodetectors for waking up microcontrollers

  • Ripoll Vercellone, Edgar
  • Reverter Cubarsí, Ferran
  • Ferrandiz, Vicent
  • Gasulla Forner, Manuel
The use of LEDs as photodetectors has been subject of study for a long time. However, LEDs manufacturers do not provide information about the response of LEDs to the light. It is essential for the designers of electronic devices to know what the behavior of LEDs is so as to develop new applications in this area. In this work, we propose the use of commercially off-the-shelf LEDs, illuminated by the flashlight of a smartphone, as a contactless wake-up system for microcontrollers that are in a sleep mode. In particular, the generated LED voltage is proposed as the wake-up signal. So, in order to choose the most suitable LED and depending of the main interfering light, the currentvoltage (I-V) characterization of different kind of LEDs is performed for two scenarios: outdoors and indoors. It is demonstrated that placing a resistor in parallel with the LEDs allows a better discrimination between the LED voltage coming from the flashlight and that from the interfering lights. Results show that red and blue LEDs are more appropriate for outdoor and indoor applications, respectively., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Real-time wave monitoring on coastal areas using LPWAN-based embedded systems

  • Carandell Widmer, Matias
  • Toma, Daniel
  • Artero Delgado, Carola
  • Gasulla Forner, Manuel
  • Río Fernández, Joaquín del
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A new embedded system is presented for real-time wave monitoring on coastal areas using SigFox communication. SigFox is a Low-Power Wide-Area Network technology that has been rarely used in coastal marine monitoring. The system is based on the low-power TD1205P module that includes a microcontroller, an accelerometer, a GNSS receiver and a SigFox transceiver. Each hour, the module estimates the wave’s maximum height (Hmax) and mean period (Tz), determines the GPS position, and wirelessly transmits the data through the SigFox network. The procedure for wave parameter estimation is based on the zero-upcrossing method using the vertical acceleration data. It was experimentally validated by attaching the embedded system to a moored buoy and comparing Hmax and Tz with that provided by a seafloor acoustic wave and current profiler, used as a reference. Results over a period of two months show a good match for Hmax but less for Tz, which cross-correlation values at zero lag of about 0.85 and 0.5, respectively. Power tests of the embedded system were also performed resulting in a lifetime estimation of 420 days with a battery pack of 3 Ah., This work was supported by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under project TEC2016-76991-P and by the project MELOA from the European Commission’s Horizon 2020 research and Innovation program under Grant Agreement No. 776280. The first author has a grant from the Secretariat of Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia on the FI program (ref. BDNS 362582)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A compact Thévenin model for a rectenna and its application to an RF harvester with MPPT

  • Gasulla Forner, Manuel
  • Ripoll Vercellone, Edgar
  • Reverter Cubarsí, Ferran
This paper proposes a compact Thévenin model for a rectenna. This model is then applied to design a high-efficiency radio frequency harvester with a maximum power point tracker (MPPT). The rectenna under study consists of an L-matching network and a half-wave rectifier. The derived model is simpler and more compact than those suggested so far in the literature and includes explicit expressions of the Thévenin voltage (Voc) and resistance and of the power efficiency related with the parameters of the rectenna. The rectenna was implemented and characterized from -30 to -10 dBm at 808 MHz. Experimental results agree with the proposed model, showing a linear current–voltage relationship as well as a maximum efficiency at Voc/2, in particular 60% at -10 dBm, which is a remarkable value. An MPPT was also used at the rectenna output in order to automatically work at the maximum efficiency point, with an overall efficiency near 50% at -10 dBm. Further tests were performed using a nearby transmitting antenna for powering a sensor node with a power consumption of 4.2 µW., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Electronic reading of a mechanical gas meter based on dual magnetic sensing

  • Ripoll Vercellone, Edgar
  • Gasulla Forner, Manuel
  • Reverter Cubarsí, Ferran
This article proposes a measurement system controlled by a microcontroller unit (MCU) for the electronic reading of a mechanical gas meter. The measurement relies on dual magnetic sensing: (a) low-cost low-power primary sensing based on reed switches connected to the digital inputs of the MCU and (b) secondary sensing based on Hall-effect sensors connected to the analogue inputs of the MCU. In addition, both sensing strategies have an active and a passive element to achieve an output that is insensitive to external interfering magnets. A prototype has been implemented and characterized under different test conditions to confirm its reliability., This work was supported by the Secretariat of University and Research of the Ministry of Business and Knowledge of the Government of Catalonia, and by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under project TEC2016-76991-P., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On measuring power efficiency in DC-DC converters at light load currents

  • Gasulla Forner, Manuel
  • Reverter Cubarsí, Ferran
This paper tackles the problematic issue of measuring the efficiency at DC-DC converters operating in PFM mode, which are used for light loads such as sensor nodes. Such converters present a pulsed input current, which hinders a correct estimation of the average input power. For estimating it, two instruments were used (a power analyzer and a current waveform analyzer) as well as two methods respectively based on the following calculations: 1) exact from the voltage and current samples and 2) approximate from the average values of voltage and current., This work was supported by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under project TEC2016-76991-P., Postprint (updated version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A microcontroller-based interface circuit for non-linear resistive sensors

  • Reverter Cubarsí, Ferran
This article proposes a circuit based on a microcontroller unit (MCU) for the direct measurement and linearization of non-linear resistive sensors, such as thermistors. The measurement relies on an embedded digital timer and does not require (either embedded or external) operational amplifiers or an analog-to-digital converter, thus resulting in a low-cost, low-power design solution. The circuit includes a known resistor with a twofold function: it is a reference for circuit auto-calibration purposes, and it is in parallel with the non-linear resistive sensor for linearization purposes., Postprint (updated version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Seat occupancy detection based on a low-power microcontroller and a single FSR

  • Sifuentes, Ernesto
  • González Landaeta, Rafael
  • Cota Ruiz, Juan
  • Reverter Cubarsí, Ferran
This paper proposes a microcontroller-based measurement system to detect and confirm the presence of a subject in a chair. The system relies on a single Force Sensing Resistor (FSR), which is arranged in the seat of the chair, that undergoes a sudden resistance change when a subject/object is seated/placed over the chair. In order to distinguish between a subject and an inanimate object, the system also monitors small-signal variations of the FSR resistance caused by respiration. These resistance variations are then directly measured by a low-cost general-purpose microcontroller unit (MCU) without using either an analogue processing stage or an analogue-to-digital converter. Two versions of such a MCU-based circuit are presented: one to prove the concept of the measurement, and another with a smart wake-up (generated by the sudden resistance change) intended to reduce the energy consumption. The feasibility of the proposed measurement system is experimentally demonstrated with subjects of different weight sitting at different postures, and also with objects of different weight. The MCU-based circuit with a smart wake-up shows a standby current consumption of 800 nA, and requires an energy of 125 µJ to carry out the measurement after the wake-up., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Design and testing of a kinetic energy harvester embedded into an oceanic drifter

  • Carandell Widmer, Matias
  • Toma, Daniel
  • Carbonell Ventura, Montserrat
  • Río Fernández, Joaquín del
  • Gasulla Forner, Manuel
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., A novel Kinetic Energy Harvester (KEH) has been developed for powering oceanic undrogued drifters. It consists on a double pendulum system capable of transforming the wave oscillations into rotation on a flywheel. This rotation is converted into DC current by an electrical generator and further processed by a power management unit (PMU). The PMU includes a “maximum power point tracking” system to maximize energy production by the generator. An oceanic drifter has also been designed to embed the KEH and a custom-made measurement system to perform real sea tests. It counts on an Inertial Measurement Unit to study the motion of the drifter and an embedded measurement system to estimate the rotation speed of the generator and the power at both the input and output of the PMU. A Wi-Fi connection is also included for data transfer at short distances. The generator was firstly characterized at the laboratory; the drifter was then placed on a linear shaker to assess its performance. Finally, the drifter was deployed in a controlled sea area with average values of wave height and frequency of 1.43 m and 0.29 Hz, respectively. In these conditions, the drifter showed horizontal and vertical oscillations with peak-to-peak accelerations of 0.8 g and power spectra centered around 1.5 Hz and 1 Hz, respectively. As a result, the KEH generated a mean output power of 0.18 mW, with peaks of 2.5 mW., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Contributions to the pendulum-type wave energy converter system for oceanic drifter applications

  • Carandell Widmer, Matias
  • Toma, Daniel
  • Gasulla Forner, Manuel
  • Río Fernández, Joaquín del
Lagrangian Drifters are autonomous floating passive devices that provide oceanographic surface data. They are low-cost, versatile and easy-deployable marine instrumentation used in climate research. One of the main challenges related to the drifter’s design is the power autonomy. Some studies explore the kinetic oscillatory movement of the waves as an Energy Harvesting (EH) source. At [1] a novel pendulum-type wave energy converter (WEC) system was presented (Fig. 1). The WEC consists of an articulated pendulum arm with a proof mass. This mass moves relatively to the drifter with pendulum motion. Then, through a gear system, rotation is accumulated and increased in a flywheel which drives a dc electrical generator. Then, a first prototype of an oceanic drifter was designed to embed the WEC and was used to perform tests in real sea conditions [2]. The main purpose of this drifter is to measure its own motion and analyze how it translates into energy production. It contains an Inertial Measurement Unit (IMU) for the motion study and a measurement system for the estimation of the WEC power generation. Results from the first sea test show a useful mean power on the order of milliwatts, which can be used as an unlimited backup powering system to recover the unit. An algorithm was developed to estimate wave parameters (height and period) from the IMU embedded on the drifter. Then, the effect of the WEC’s inertia on this estimation was assessed by deploying the drifter in a controlled wave flume. It was concluded that the WEC does not generate significant errors [3]. Finally, several maximum power point tracking (MPPT) techniques for maximizing the WEC harvested energy were evaluated. The designed WEC, together with a power management unit (PMU), was tested on a linear shaker to compare three MPPT techniques, the Constant Voltage versus two variants of the Fractional Open Circuit Voltage (FOCV). Results show a 25% improvement on the scavenged energy with one of the proposed FOCV techniques with respect to the other ones [4]. The purpose of this article is to review the contributions made on WEC systems for lowpower marine environmental monitoring applications., This work was supported by the project MELOA from the European Commission’s Horizon 2020 research and Innovation program under Grant Agreement No. 776280 and by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under project TEC2016-76991-P. The first author has a grant from the Secretariat of Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia on the FI program (ref. BDNS 362582). The authors extend their thanks to researchers from LIM – UPC for their kind support and yield the facilities of CIEM where the experimental tests were done., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Optimum MPPT strategy for low-power pendulum-type wave energy converters

  • Carandell Widmer, Matias
  • Toma, Daniel
  • Río Fernández, Joaquín del
  • Gasulla Forner, Manuel
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Maximum Power Point Tracking (MPPT) techniques for low-power pendulum-type Wave Energy Converters were evaluated. A Kinetic Energy Harvester previously designed, together with a Power Management Unit, were tested on a linear shaker to compare three MPPT techniques, the Constant Voltage versus two variants of the Fractional Open Circuit Voltage (FOCV). Results show a 25% improvement on the scavenged energy with one of the proposed FOCV techniques with respect to the other ones., This work was supported by the project MELOA from the European Commission’s Horizon 2020 research and Innovation program under Grant Agreement No. 776825 and by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under project TEC2016-76991-P. The first author has a grant from the Secretariat of Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia on the FI program (ref. BDNS 362582)., Peer Reviewed, Postprint (author's final draft)