Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A gap waveguide-based compact rectangular waveguide to a packaged microstrip inline transition

  • Pérez Escudero, José Manuel
  • Torres García, Alicia E.
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
In this paper two different simple to design and easy to manufacturing transitions from a microstrip to rectangular waveguide based on ridge and groove gap waveguides are studied. The first one is based on a combination of a groove and ridge gap waveguide. In this case, the microstrip substrate occupies the whole bottom metallic housing block, namely, the transition and the gap between the bed of nails and the lid; therefore, it does not require any substrate shaping. Nevertheless, the transition needs to replace groove waveguide by ridge gap waveguide sections to avoid higher-order mode excitation. In the second approach, based on only a groove gap waveguide, the substrate is shaped to be only in the microstrip section, that is, outside the bed of nails area. This leads to a simplification of the design procedure. Prototypes of both transitions have been characterized, showing good agreement with the simulations taking into account the manufacturing tolerances. Performance comparable to the state-of-the-art in this frequency band has been achieved., This research was funded by the Spanish Ministry of Economy and Competitiveness, project numbers TEC2013-47753-C3-1-R, TEC2016-76997-C3-1-R and PID2019-109984RB-C43.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A water content continuous monitoring of grapevine xylem tissue using a portable low-power cost-effective FMCW radar

  • Quemada Mayoral, Carlos
  • García González, Cebrián
  • Iriarte Galarregui, Juan Carlos
  • Marín Ederra, Diana
  • Gastón Beraza, Diego
  • Miranda Jiménez, Carlos
  • Gonzalo García, Ramón
  • Maestrojuán Biurrun, Itziar
  • Santesteban García, Gonzaga
  • Ederra Urzainqui, Íñigo
This paper presents the real-time monitoring of a grapevine’s water content that flows up through the xylem tissue by means of a frequency-modulated continuous-wave (FMCW) radar. The application of an optimization process, based on the super-resolution multiple signal classification (MUSIC) algorithm, has enabled the reduction of the bandwidth required to discern the xylem water content, and thus the operating frequency, achieving a depth resolution of at least 3 mm. This design advantage has resulted in a significant step forward towards a real life application, allowing the use of fully-integrated off-the-shelf components in order to implement a completely portable low-power cost-effective radar at 23.1 GHz with a 3.4 GHz bandwidth. The sensor performance has been evaluated by means of three different experiments: irrigation cycles, day/night cycles and comparison between irrigation cycles at different temperatures. From the experimental results, it is possible to assert that the contactless sensor presented in this work is very sensitive to changes in the plant’s water content, differentiating between daytime and nighttime. In addition, it has been proved that temperature has a noticeable influence over the evapotranspiration, observing negative drying slopes of 5.62 mV/cycle and 6.28 mV/cycle at 23ºC and 26ºC respectively., This work was supported in part by the Spanish Ministry of Economy and Competitiveness under Project TEC2016-76997-C3-1-R and in part by the Navarra Government under Project PI025 VITHZ and Project 0011-1365-2016-000084 RAFF.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Silicon integrated subharmonic mixer on a photonic-crystal platform

  • Torres García, Alicia E.
  • Pérez Escudero, José Manuel
  • Teniente Vallinas, Jorge
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photoniccrystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a simple, easy to integrate, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the stateof-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds., This work was supported by the Spanish Ministry of Economy and Competitiveness, TEC2016-76997-C3-1-R and PID2019-109984RB-C43.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Experimental validation of a Ku-band dual circularly polarized metasurface antenna

  • Tellechea Pereda, Amagoia
  • Caminita, Francesco
  • Martini, Enrica
  • Ederra Urzainqui, Íñigo
  • Teniente Vallinas, Jorge
  • Iriarte Galarregui, Juan Carlos
  • Gonzalo García, Ramón
  • Maci, Stefano
The experimental validation of a Ku-band dual circularly polarized (CP) broadside-beam metasurface (MTS) antenna is presented. A radially modulated anisotropic single layer MTS has been synthesised employing sub-wavelength elliptical slotted metallic patches printed on top of a thin Arlon grounded substrate. In the structure, two decoupled phasematched transverse magnetic and transverse electric surface waves (SWs) are excited, which interact with the modulated surface leading to a CP broadside radiation. Two different orthomode transducers have been designed to excite the SWs with orthogonal polarization and equal amplitude. The first feeding system is composed of a metallic stepped septum inside an airfilled square waveguide. A conical section is included to match the output port of the square waveguide with the terminal, dielectric filled circular waveguide. The second feed is much more compact and efficient and it is composed of a circular waveguide completely filled by a dielectric. Depending on the input port excited on the feeds, two TE11 modes are excited with ±90° phase shift, which determine the right-hand or left-hand sense of the broadside beam generated by the MTS. Manufacturing details of the MTS and excitations are given and the measurements are compared with the simulation results. Finally, conclusions are drawn., The authors would like to thank financial support by the Spanish Ministry of Science and Innovation, Direccion General de Investigacion y Gestion del Plan Nacional de I+D+I, Subdireccion General de Proyectos de Investigacion, Project No. TEC2013-47753-C3-1-R and Project No. TEC2016- 76997-C3-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Comparison of modified Soret lenses for dual band integrated detectors

  • Torres García, Alicia E.
  • Pérez Escudero, José Manuel
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
This paper presents the comparison of different modified Soret lenses suitable for a millimeter and submillimeterwave dualband integrated pixel detectors. The approach is based on the modification of a printed planar Soret lens, designed to operate in the sub-mm range, to obtain an antenna at the millimeter region. Three modifications of a transmission-mode Soret Lens at 850 GHz based on spiral, logarithmic and meander antennas geometries have been analyzed with a combination of Kirchhoffs Diffraction and full-wave simulation methods. The performance of the designs has been experimentally demonstrated in the submillimeterwave band, showing good agreement with simulation results., The authors would like to thank financial support by the Spanish Ministry of Science and Innovation, Project No. TEC2013-47753-C3-1-R, TEC2014-61817-EXP and TEC2016-76997-C3-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

300 GHz optoelectronic transmitter combining integrated photonics and electronic multipliers for wireless communication

  • Ali, Muhsin
  • Pérez Escudero, José Manuel
  • Guzmán Martínez, Robinson Cruzoe
  • Lo, Mu Chieh
  • Ederra Urzainqui, Íñigo
  • Gonzalo García, Ramón
  • García Muñoz, Luis Enrique
THz communications systems at carrier frequencies above 200 GHz are the key to enable next-generation mobile communication networks with 100 Gbit/s wireless data rates. One of the key questions is, which carrier frequency generation technique will be the most suitable. This is currently addressed by two separate approaches, electronics-based and photonics-based. We present in this paper a truly microwave photonic approach that benefits from the main key features of each, bandwidth, tunability, stability and fiber compatibility from photonics and power handling capability from the electronics. It is based on a Photonic Local Oscillator (PLO), generating a 100 GHz frequency, fed into an electronic frequency multiplier. A high speed uni-travelling carrier photodiode (UTC-PD) provides the 100 GHz PLO for Schottky tripler diodes, generating 300 GHz signal. To feed the UTC-PD, we present a photonic integrated mode locked laser source. According to the simulations and measurements, the developed transmitter can produce a maximum of 12 μWof THz power at 280 GHz., This work has been supported by European Union’s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 642355 FiWiN5G, as well as by Spanish Ministerio de Economía y Competitividad through Programa Estatal de Investigación, Desarrollo e Inovación Orientada a los Retos de la Sociedad (grant iTWIT, TEC2016-76997-C3-3-R).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A millimeter-wave 4th-harmonic Schottky diode mixer with integrated local oscillator

  • Pérez Escudero, José Manuel
  • Quemada Mayoral, Carlos
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
In this paper the design and experimental validation of a fourth-harmonic mixer based on Schottky diodes working around 300 GHz is presented. The main novelty of this work consists in the integration of an MMIC-based local oscillator, working around 75 GHz, and a mixer in the same metallic block housing. A prototype has been characterized using the Y-Factor method and yields a best measured conversion loss and an equivalent noise temperature of 14 dB and 9600 K, respectively. This performance is comparable to the state-of-the-art for this type of mixer., This research was funded by the Spanish MINECO, Project No. TEC2016-76997-C3-1-R, and by the Spanish State Research Agency, Project No. PID2019-109984RB-C43/AEI/10.13039/501100011033.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Modified Soret lenses for dual band integrated detectors at submillimetre and millimetre wavelengths

  • Torres García, Alicia E.
  • Pérez Escudero, José Manuel
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photonic crystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a simple, easy to integrate, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the state of-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds., The authors would like to thank financial support by the Spanish Ministry of Science and Innovation, Dirección General de Investigación y Gestión del Plan Nacional de I+D+I,Subdirección General de Proyectos de Investigación, Project No. TEC2013-47753-C3-1-R, TEC2014-61817-EXP and TEC2016-76997-C3-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A simplified design inline microstrip-to-waveguide transition

  • Ederra Urzainqui, Íñigo
  • Gonzalo García, Ramón
  • Pérez Escudero, José Manuel
  • Torres García, Alicia E.
A simplified design of an inline transition between microstrip and rectangular waveguide is presented in this paper. The transition makes use of a dielectric filled rectangular waveguide (DFRW) as an intermediate step, which simplifies manufacturing and allows for an analytical design. The behavior of the transition has been experimentally validated in the W-band by means of a back-to-back configuration. Good performance has been achieved: a return loss greaterthan 10 dB and mean insertion loss lower than 1 dB., This research was funded by the Spanish Ministry of Economy and Competitiveness, grant number TEC2013-47753-C3-1-R and TEC2016-76997-C3-1-R
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A Chebyshev transformer-based microstri-to-groove-gap-waveguide inline transition for MMIC packaging

  • Pérez Escudero, José Manuel
  • Torres García, Alicia E.
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
The gap waveguide technology has become an alternative to millimeter- and submillimeter-wave electronic circuit packaging thanks to the loss reduction associated with its use. In this paper, a simplified design of an inline transition between a microstrip and a groove gap waveguide (GGW) operating at the W-band is presented. The transition consists of a tapered microstrip line and a Chebyshev adapter that couple the quasi-TEM mode of the microstrip line to the so-called vertical mode of the GGW. The simplicity of this design makes this transition appropriate for monolithic microwave integrated circuit (MMIC) packaging at millimeter frequencies and above. The simulation results have been experimentally validated in the W-band. A good performance has been achieved, resulting in a return loss better than 10 dB and a mean insertion loss lower than 2 dB., This work was support by the Spanish MINECO under Project TEC2013-47753-C3-1-R and Project TEC2016-76997-C3-1R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Remote sensing for plant water content monitoring: a review

  • Quemada Mayoral, Carlos
  • Pérez Escudero, José Manuel
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
  • Santesteban García, Gonzaga
  • Torres Molina, Nazareth
  • Iriarte Galarregui, Juan Carlos
Las redes sociales se han convertido en una de las principales fuentes de información, especialmente entre los más jóvenes. Al mismo tiempo, se ha incrementado la producción y circulación de información falsa o fake news a través de las redes. En este contexto, resulta crucial que los jóvenes adquieran estrategias y competencias para realizar una lectura crítica de la información que consumen. Este estudio busca analizar el comportamiento del alumnado de secundaria ante la información falsa y el efecto de una intervención didáctica, realizada online durante la pandemia de la covid-19, cuyo objetivo era que el alumnado desarrollara competencias para detectar noticias falsas. Se trata de una investigación participativa con un diseño de pre-test y post-test. Los resultados muestran que el alumnado incrementó su competencia para identificar algunos tipos de falsedad como la información no probada y la información tergiversada, si bien tuvo problemas para reconocer información descontextualizada o el uso de lenguaje discriminatorio. Las estrategias que más utilizó son la comprobación de datos en internet y el uso de verificadores. Se observaron comportamientos diferenciados entre el alumnado que identificó la información falsa y el que no lo hizo. Las conclusiones apuntan a la necesidad de trabajar en el aula de forma integral, extensiva y transversal la evaluación de la información partiendo de las habilidades que el alumnado ya posee., This paper reviews the different remote sensing techniques found in the literature to monitor plant water status, allowing farmers to control the irrigation management and to avoid unnecessary periods of water shortage and a needless waste of valuable water. The scope of this paper covers a broad range of 77 references published between the years 1981 and 2021 and collected from different search web sites, especially Scopus. Among them, 74 references are research papers and the remaining three are review papers. The different collected approaches have been categorized according to the part of the plant subjected to measurement, that is, soil (12.2%), canopy (33.8%), leaves (35.1%) or trunk (18.9%). In addition to a brief summary of each study, the main monitoring technologies have been analyzed in this review. Concerning the presentation of the data, different results have been obtained. According to the year of publication, the number of published papers has increased exponentially over time, mainly due to the technological development over the last decades. The most common sensor is the radiometer, which is employed in 15 papers (20.3%), followed by continuous-wave (CW) spectroscopy (12.2%), camera (10.8%) and THz time-domain spectroscopy (TDS) (10.8%). Excluding two studies, the minimum coefficient of determination (R2) obtained in the references of this review is 0.64. This indicates the high degree of correlation between the estimated and measured data for the different technologies and monitoring methods. The five most frequent water indicators of this study are: normalized difference vegetation index (NDVI) (12.2%), backscattering coefficients (10.8%), spectral reflectance (8.1%), reflection coefficient (8.1%) and dielectric constant (8.1%)., This research was funded by the Spanish MINECO, Project No. TEC2016-76997-C3-1-R, and by the Spanish State Research Agency, Project No. PID2019-109984RBC43/AEI/10.13039/501100011033.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Design of 300 ghz combined doubler/subharmonic mixer based on schottky diodes with integrated mmic based local oscillator

  • Pérez Escudero, José Manuel
  • Quemada Mayoral, Carlos
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
In this paper the design and experimental characterization of a combined doublersubharmonic mixer based on Schottky diodes which uses a 75 GHz MMIC based local oscillator is presented. This solution integrates in the same substrate the doubler and the mixer, which share the same metallic packaging with the local oscillator. The prototype has been fabricated and measured. For characterization, the Y-Factor technique has been used and the prototype yields a best conversion loss and equivalent noise temperature of 11 dB and 1976 K, respectively, at 305 GHz. This performance is close to the state of the art, and shows the potential of this approach, which allows a significant reduction in terms of size and volume., This research was funded by the Spanish MINECO, Project No. TEC2016-76997-C3-1-R, and by the Spanish State Research Agency, Project No. PID2019-109984RB-C43/AEI/10.13039/501100011033.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Real-time imaging with frequency scanning array antenna for industrial inspection applications at W band

  • Larumbe Gonzalo, Belén
  • Laviada, Jaime
  • Ibáñez Loinaz, Asier
  • Teniente Vallinas, Jorge
A real-time imaging system based on a frequency scanning antenna for conveyor belt setups is presented in this paper. The frequency scanning antenna together with an inexpensive parabolic reflector operates at the W band enabling the detection of details with dimensions in the order of 2 mm. In addition, a low level of sidelobes is achieved by optimizing unequal dividers to window the power distribution for sidelobe reduction. Furthermore, the quality of the images is enhanced by the radiation pattern properties. The performance of the system is validated by showing simulation as well as experimental results obtained in real time, proving the feasibility of these kinds of frequency scanning antennas for cost-effective imaging applications., This work was supported by the Spanish Ministry of Economy and Competitiveness Project Nos. TEC2016-76997-C3-1-R, TEC 2013-47753-C3-1-R, RTC-2014-2110-2, and postdoctoral fellowship FPDI-2013-16278.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Bull’s-eye antenna with circular polarization at millimeter waves based on ridge gap waveguide technology

  • Pérez Quintana, Dayan
  • Ederra Urzainqui, Íñigo
  • Beruete Díaz, Miguel
In this communication, a Bull’s-Eye (BE) antenna with circular polarization (CP) based on ridge gap waveguide (RGW) technology is numerically and experimentally demonstrated. The structure is excited from the bottom with a standard WR-15 waveguide (V -band) coupled through a step transition to a ridgeline that ends in two orthogonal arms of different lengths to generate CP. Radiation is coupled to the top plate by a central diamond slot surrounded by the BE structure, which consists of four concentric periodic corrugations around the slot. Simulations and experimental results are in good agreement, with axial ratio below 1 dB at the operation frequency and peak gain of 18.4 dB. The antenna has right-handed CP (RHCP) with polarization discrimination of more than 30 dB., This work was supported by the Ministerio de Ciencia, Innovación y Universidades under Grants RTI2018-094475-B-I00 (MCIU/AEI/FEDER, UE), TEC2016-76997-C3-1-R. and PID2019-109984RB-C43.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Design of a groove gap waveguide to microstrip inline transition

  • Pérez Escudero, José Manuel
  • Torres García, Alicia E.
  • Gonzalo García, Ramón
  • Ederra Urzainqui, Íñigo
In this paper the design of an inline transition between microstrip and groove gap waveguide operating at Wband is presented. The transition consists of two sections: a tapered microstrip line and a Chebyshev transformer. The simplicity of this design makes this transition appropriate for MMIC packaging at millimeter frequencies and above. Experimental validation has been carried out in theW-band. Good performance has been achieved: return loss better than 10 dB and mean insertion loss lower than 2 dB., The authors would like to thank financial support by the Spanish MINECO, Project No. TEC2013-47753-C3-1-R and Project No. TEC2016-76997-C3-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Dispersion properties of an elliptical patch with cross shaped aperture for synchronized propagation of transverse magnetic and electric surface waves

  • Tellechea Pereda, Amagoia
  • Ederra Urzainqui, Íñigo
  • Gonzalo García, Ramón
  • Iriarte Galarregui, Juan Carlos
This paper presents a novel pixel geometry for the implementation of metasurfaces requiring synchronized phase propagation of transverse magnetic (TM) and transverse electric (TE) modes. The pixel is composed by an elliptical metallic patch with an asymmetric cross-shaped aperture in the center, printed on a grounded slab. A practical implementation of a metasurface was carried out employing such a pixel geometry. Simulation results show similar frequency dispersion properties for both modes within the working frequency band, in agreement with the theoretical basis., The authors would like to thank the financial support by the Spanish Ministry of Economy and Competitiveness, Project No. TEC2013-47753-C3-1-R and TEC2016-76997-C3-1-R and by the Gobierno de Navarra, Project PI017 COMUNICACIONES 5G and PI018 COMUNICACIONES 5G.